Instruction Manual

FCC ID: K44474500

Users Manual

Download: PDF
FCCID_2717028

NXR-5700 NXR-5800 VHF DIGITAL BASE-REPEATER UHF DIGITAL BASE-REPEATER INSTRUCTION MANUAL BASE-RELAIS NUMÉRIQUE VHF BASE-RELAIS NUMÉRIQUE UHF MODE D’EMPLOI BASE-REPETIDOR DIGITAL VHF BASE-REPETIDOR DIGITAL UHF MANUAL DE INSTRUCCIONES B5A-0713-00 (K,K3,K5)

NXR-5700 / NXR-5800 INSTRUCTION MANUAL VHF DIGITAL BASE-REPEATER / UHF DIGITAL BASE-REPEATER THANK YOU! We are grateful you purchased this KENWOOD repeater. ◆ Do not install the repeater in explosive atmospheres KENWOOD incorporates the latest in advanced technology into (inflammable gas, dust particles, metallic powders, grain all of our products. As a result, we feel strongly that you will be powders, etc.). pleased with the quality and features of this product. PRECAUTIONS ◆ This repeater is intended for use as a fixed base station with • Do not expose the unit to rain or moisture; to prevent fire or the antenna located outdoors on the rooftop or on an antenna electric shock. tower. • Do not open the unit under any circumstances; to avoid risk ◆ This repeater is designed for a 13.6 V DC power source! of electric shock. Never use a 24 V DC or higher source to power the repeater. ◆ Use only the supplied DC cord. • Do not expose the unit to long periods of direct sunlight, nor place it close to heating appliances. ◆ Do not remove the ferrite core attached to the DC cord. Doing so may cause interference with radio communications. • Do not place the unit in excessively dusty and/or humid areas, nor on unstable surfaces. UNPACKING AND CHECKING EQUIPMENT • Do not put the plastic bag used for packing of this equipment on the place which reaches a small child's hand. It will Note: The following unpacking information is for use by your become a cause of suffocation if it wears flatly. KENWOOD dealer, an authorized KENWOOD service center, or the factory. • Always switch the transceiver power off before installing optional accessories. Carefully unpack the repeater. We recommend that you identify the items listed in the following table before discarding the • If you detect an abnormal odor or smoke coming from the packing material. If any items are missing or have been damaged unit, disconnect the power from the unit immediately. Contact during shipment, file a claim with the carrier immediately. your KENWOOD service center or dealer. Item Part Number Quantity Front glass B10-2781-XX 1 NOTICES TO THE USER Dressed screw N08-0563-XX 1 Bracket J29-0725-XX 2 ◆ Government law prohibits the operation of unlicensed radio Flat head machine screw N32-4008-XX 4 transmitters within the territories under government control. Handle K01-0421-XX 1 ◆ Illegal operation is punishable by fine and/or imprisonment. DC cord E30-3427-XX 1 ◆ Refer service to qualified technicians only. Lead wire with connector (15 pin) E31-3228-XX 1 Fuse (15 A) F52-0042-XX 1 One or more of the following statements may be applicable: SYNC Cable E30-7701-XX 1 FCC WARNING Instruction Manual B5A-0713-XX 1 This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved by the party responsible/JVC KENWOOD. The user could lose the authority to INSTALLATION operate this equipment if an unauthorized change or modification is To install the handles onto the front panel of the repeater, align made. the handles with the holes on the front panel, then secure the handles using the supplied screws. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY Please consult your dealer for installing the repeater and THE FCC antenna. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. MICROPHONE These limits are designed to provide reasonable protection against harmful interference in a residential installation. Connect an optional KMC-30, KMC-35, KMC-9C, or KMC-53 This equipment generates, uses and can generate radio frequency KENWOOD microphone to the MICROPHONE jack on the front energy and, if not installed and used in accordance with the panel. instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful OCXO UNIT (KXK-3):Option interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to The OCXO unit (KXK-3) is an Oven Controlled Crystal Oscillator correct the interference by one or more of the following measures: (OCXO) unit. • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer for technical assistance. The AMBE+2TM voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, Firmware Copyrights reverse engineer, or disassemble the Object Code, or in any other The title to and ownership of copyrights for firmware embedded in way convert the Object Code into a human-readable form. U.S. KENWOOD product memories are reserved for JVC KENWOOD Patent Nos. #6,199,037, #6,912,495, #8,200,497, #7,970,606, and Corporation. #8,359,197. 1

CONTROLS AND FUNCTIONS ■ Front Panel a b c d e f g STATUS 1 2 3 4 5 6 7 8 VOLUME TAKE RPT MON OVER DISABLE CTRL OCXO BUSY TX POWER A B C MICROPHONE OFF/ l k j ih a Speaker i TX indicator b CH/STATUS Display Lights red while transmitting. Two 17-segment digits display the channel number, name, j BUSY indicator or status. Lights green while a signal is being received. c STATUS indicator k OCXO indicator Indicates the status of the repeater. (NXDN mode) The OCXO indicator shows the state of the reference d Programmable Function keys 10 MHz oscillator : Press these keys to activate their programmable functions. Lights Green when using a reference signal from an e USB jack (B-Type) optional OCXO unit (KXK-3). Connect to the PC using a USB cable. Lights Orange when using a reference signal from another f VOLUME control repeater. Turn clockwise until a click sounds, to unmute the audio. Lights red when no reference signal is available or when Rotate to adjust the audio. Turn counterclockwise fully to an error occurs. mute the audio. Does not light when the reference signal is an internal g MICROPHONE jack VCXO signal. Connect a microphone to this 8-pin modular jack. l CTRL indicator h POWER indicator The CTRL indicator shows the control channel status Lights green when power is supplied to the DC 13.6V jack. while using Digital trunking : Blinks red when an abnormal voltage is present. While Lights Green when the repeater is used as control channel. blinking, the repeater cannot be used. Blinks Green when using a non-dedicated control channel. ■ Rear Panel a b c d e f g h i j TEST/SPKR FUSE DC 13.6V SYNC LAN REF OUT REF IN CONTROL I/O 1 2 15A RX TX a RX IN jack f REF OUT jack Connect an RX antenna or a duplexer to this BNC Connect to another repeater within the site to supply a receptacle. reference signal. b TEST/SPKR jack g REF IN jack Test input/output jack. Connect an external speaker to this Connect from another repeater within the site to receive a jack. When using a Built-in speaker, connect the attached reference signal. Lead wire with connector (15 pin) to this jack. h FUSE c CONTROL I/O jack Insert 15 A blade fuse into this fuse holder. Connect a repeater controller or a remote panel to this i DC 13.6V jack DB-25 interface. Connect a 13.6 V DC power supply to this jack. d SYNC 1 / 2 jack j TX OUT jack Connect to another repeater to use synchronous frame Connect a TX antenna or a duplexer to this BNC receptacle. signaling for digital trunking. e LAN jack Connect to Ethernet. Use the category 5e or higher TRANSCEIVER OPERATION standard STP cable shorter than 3 meters. ■ Receive REPEATER OPERATION Adjust the volume to your desired level. You may need to Note: Please consult your dealer for programming the repeater. readjust the volume if you are having interference while Due to the frequency stability on the 6.25 kHz bandwidth channel, receiving a message from your dispatcher or another member when operating the repeater using an optional OCXO unit, allow the unit to warm up after turning the power on. Refer to the KXK-3 in your fleet. instruction manual concerning the warm up duration. The BUSY indicator lights green while a signal is being After turning on the power, wait for approximately 10 seconds for received. the VCXO or 5 minutes for the OCXO (when mounting) to warm up. During this time, the CH/STATUS Display will blink. The keys will function when they are pressed. ■ Transmit When power is applied to the unit, the POWER indicator lights 1 Listen to the channel before transmitting, to make sure it green. Turn the VOLUME control clockwise until a click sounds, to is not being used. unmute the audio. Rotate to adjust the audio. Turn the VOLUME 2 Press the microphone PTT switch, then speak in your control counterclockwise fully to mute the audio. normal speaking voice. The BUSY indicator lights green while receiving a signal and the The TX indicator lights red while transmitting. TX indicator lights red while transmitting. 2 3 When you finish speaking, release the PTT switch.

Addendum Terminal Description MIC (Modular Jack) Control I/O (D-SUB 25 Pin) CONNECTOR Pin Pin Pin Name Description Specification I/O Notes NO. Pin Name Description Specification I/O Notes NO. 1 NC Not used Not used − 1 NC Not used Not used − 2 SB Power Output 13.6 V O 2 RXD Asynchronous Receive Data Comform to RS-232C standard I 3 GND GND GND − 3 TXD Asynchronous Send Data Comform to RS-232C standard O 4 PTT PTT Signal Input Impedance 100 k I 4 AI1 Programmable Function Input 1 Input Impedance 47 k I 5 MICG MIC GND MIC GND − 5 AI2 Programmable Function Input 2 Input Impedance 47 k I 6 MIC MIC Input 600  I 6 AI3 Programmable Function Input 3 Input Impedance 47 k I 7 HOOK Hook Detection Input Impeadance 100 k I 7 DG Digital GND Digital GND − 8 NC Not used Not used − 8 TD TX Data Input Input Impedance 600  I not Pre-emphasis 9 TA TX Audio Input Input Impedance 600  I Pre-emphasis USB (USB Type-B) 10 RD RX Data Output Load Impedance 4.7 k O not De-emphasis Pin Pin Name Description Specification I/O Notes 11 RA RX Audio Output Load Impedance 4.7 k O De-emphasis NO. 12 RXG RX Signal GND RX Signal GND − 1 VBUS USB VBUS Conform to USB specification I 13 SPM Speaker Mute Input Impedance 47 k I 2 D- USB Data minus Conform to USB specification I/O 14 BER CLK For Bit Error Rate Clock CMOS O 3 D+ USB Data plus Conform to USB specification I/O 15 EMON External Monitor Switch Input Impedance 47 k I 4 GND USB GND USB GND − 16 EPTT External PTT Switch Input Impedance 47 k I TEST/ SPEAKER CONNECTOR 17 SC Squelch Control Output level 0 or 5 V O 18 BER DAT For Bit Error Rate Data CMOS O Pin Pin Name Description Specification I/O Notes NO. 19 TXG TX Signal GND TX Signal GND − 1 SB Power Output 13.6 V O 20 IO1 Programmable Function I/O 1 Input Impedance 47 k I/O Output level 0 or 5 V 2 SB Power Output 13.6 V O 21 IO2 Programmable Function I/O 2 Input Impedance 47 k I/O Output level 0 or 5 V 3 NC Not used Not used − 22 IO3 Programmable Function I/O 3 Input Impedance 47 k I/O Output level 0 or 5 V 4 GND GND GND − 23 IO4 Programmable Function I/O 4 Input Impedance 47 k I/O Output level 0 or 5 V 5 GND GND GND − 24 IO5 Programmable Function I/O 5 Input Impedance 47 k I/O Output level 0 or 5 V 6 SPG Speaker GND Speaker GND − 25 IO6 Programmable Function I/O 6 Input Impedance 47 k I/O Output level 0 or 5 V 7 RD RX Data Output Allowable load MIN 100 k O not De-emphasis LAN (Modular Jack) 8 RSSI RSSI Signal Output Output Level 0 to 5 V O 9 SPI Internal Speaker Input Short with "SPO" I Pin Pin Name Description Specification I/O Notes NO. 10 AO1 Open Collector Terminal Allowable current value MAX 200 mA O 1 TD+ TX Signal + Comform to IEEE802.3 standard O 100 Mbps 11 AO2 Open Collector Terminal Allowable current value MAX 200 mA O 2 TD- TX Signal − Comform to IEEE802.3 standard O 100 Mbps 12 SPO External Speaker Output Output Level 3W (5%Distortion) O 3 RD+ RX Signal + Use Designated Transformer I 100 Mbps 13 AO3 Open Collector Terminal Allowable current value MAX 200 mA O 4 NC Not used Not used − 14 AO4 Open Collector Terminal Allowable current value MAX 200 mA O 5 NC Not used Not used − 15 AO5 Open Collector Terminal Allowable current value MAX 200 mA O 6 RD- RX Signal − Use Designated Transformer I 100 Mbps 7 NC Not used Not used − 8 NC Not used Not used − SYNC 1, 2 Connector (There are two connectors) Pin Pin Name Description Specification I/O Notes NO. 1 FRMA RS-485 Differential Signal A Conform to RS485 I/O 2 NC Not used Not used − 3 NC Not used Not used − 4 FRMB RS-485 Differential Signal B Conform to RS485 I/O RX ANT Impedance 50  TX ANT Impedance 50  REF IN External Reference Signal Input (10 MHz). Impedance : more than 1 k REF OUT Reference Signal Distribution (10 MHz). Load Impedance : more than 50  B5K-0197-00

MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS • Use only manufacturer or dealer supplied antennas. • Antenna Minimum Safe Distance: 180 cm (6 feet). • Antenna Gain: 0 dBd referenced to a dipole. The Federal Communications Commission has adopted a safety standard for human exposure to RF (Radio Frequency) energy which is below the OSHA (Occupational Safety and Health Act) limits. • Antenna Mounting: The antenna supplied by the manufacturer or radio dealer must not be mounted at a location such that during radio transmission, any person or persons can come closer than the above indicated minimum safe distance to the antenna, i.e. 180 cm (6 feet). • To comply with current FCC RF Exposure limits, the antenna must be installed at or exceeding the minimum safe distance shown above, and in accordance with the requirements of the antenna manufacturer or supplier. • Vehicle installation: The antenna can be mounted at the center of a vehicle metal roof or trunk lid, if the minimum safe distance is observed. • Base Station Installation: The antenna should be fixed-mounted on an outdoor permanent structure. RF Exposure compliance must be addressed at the time of installation. Antenna substitution: Do not substitute any antenna for the one supplied or recommended by the manufacturer or radio dealer. You may be exposing person or persons to excess radio frequency radiation. You may contact your radio dealer or the manufacturer for further instructions. Maintain a separation distance from the antenna to person(s) of at least 180 cm (6 feet). You, as the qualified end-user of this radio device must control the exposure conditions of bystanders to ensure the minimum separation distance (above) is maintained between the antenna and nearby persons for satisfying RF Exposure compliance. The operation of this transmitter must satisfy the requirements of Occupational/Controlled Exposure Environment, for work-related use, transmit only when person(s) are at least the minimum distance from the properly installed, externally mounted antenna. Transmit only when people outside the vehicle are at least the recommended minimum lateral distance away from the antenna/vehicle. B59-2667-00


Document Created: 2015-07-15 09:59:40
Document Modified: 2015-07-15 09:59:40
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC