Test Report

FCC ID: JVPH0523

Test Report

Download: PDF
FCCID_257759

PCTEST Engineering Laboratory, Inc. 6660-B Dobbin Road • Columbia, MD 21045 • U.S.A. TEL (410) 290-6652 • FAX (410) 290-6654 http://www.pctestlab.com CERTIFICATE OF COMPLIANCE FCC Part 24 & 22 Certification BENQ CORPORATION Dates of Tests: June 5-7, 2002 157 Shan-Ying Road Kweishan Test Report S/N: 22/24.220605283.JVP Taoyuan 333 TAIWAN, R.O.C. Test Site: PCTEST Lab, Columbia MD Attn: George Chiou Technical Manager FCC ID JVPH0523 APPLICANT BENQ CORPORATION Classification: Licensed Portable Transmitter Held to Ear (PCE) FCC Rule Part(s): §24(E), §22(H), §22.901(d); §2 EUT Type: Tri-Mode Dual-Band Analog/PCS Phone (AMPS/CDMA) Model: C900 Tx Frequency Range: 824.04MHz — 848.97MHz (AMPS) / 824.70 — 848.31MHz (CDMA) 1851.25MHz — 1908.75MHz (PCS CDMA) Rx Frequency Range: 869.04MHz — 893.97MHz (AMPS) / 869.70 — 893.31MHz (CDMA) 1931.25MHz — 1988.75MHz (PCS CDMA) Max. RF Output Power: 0.606 W ERP AMPS (27.823 dBm) / 0.388 W ERP CDMA (25.883 dBm) 0.396 W EIRP PCS CDMA (25.981 dBm) Max. SAR Measurement: 1.46W/kg AMPS Head SAR; 0.93W/kg AMPS Body SAR; 0.93W/kg CDMA Head SAR; 0.61W/kg CDMA Body SAR; 1.45W/kg PCS CDMA Head SAR; 0.52W/kg PCS CDMA Body SAR Emission Designator(s): 40K0F8W / 40K0F1D (AMPS), 1M25F9W (CDMA) This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in §2.947. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. PCTEST certifies that no party to this application has been denied the FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. 220605283.JVP FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 1 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

TABLE OF CONTENTS ATTACHMENT A: COVER LETTER(S) ATTACHMENT B: ATTESTATION STATEMENT(S) ATTACHMENT C: TEST REPORT 1.1 SCOPE 3 2.1 INTRODUCTION 4 3.1 INSERTS 5 4.1 DESCRIPTION OF TESTS 6-10 5.1 EFFECTIVE RADIATED POWER OUTPUT 11-12 6.1 EQUIVALENT ISOTROPIC RADIATED POWER 13 7.1 RADIATED MEASUREMENTS 14-22 8.1 FREQUENCY STABILITY 23-26 9.1 PLOTS OF EMISSIONS 27 10.1 LIST OF TEST EQUIPMENT 28 11.1 SAMPLE CALCULATIONS 29 12.1 CONCLUSION 30 ATTACHMENT D: TEST PLOTS ATTACHMENT E: FCC ID LABEL / LOCATION ATTACHMENT F: TEST SETUP PHOTOGRAPHS ATTACHMENT G: EXTERNAL PHOTOGRAPHS ATTACHMENT H: INTERNAL PHOTOGRAPHS ATTACHMENT I: BLOCK DIAGRAM(S) ATTACHMENT J: SCHEMATIC DIAGRAM(S) ATTACHMENT K: OPERATIONAL / CIRCUIT DESCRIPTION ATTACHMENT L: PARTS LIST/TUNE UP PROCEDURE ATTACHMENT M: USER’S MANUAL ATTACHMENT N: SAR MEASUREMENT DATA ATTACHMENT O: SAR TEST DATA ATTACHMENT P: SAR TEST SETUP PHOTOGRAPHS ATTACHMENT Q: DIPOLE VALIDATION ATTACHMENT R: PROBE CALIBRATION FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 2 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

MEASUREMENT REPORT 1.1 Scope Measurement and determination of electromagnetic emissions (EME) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission. §2.1033 General Information Applicant Name: BENQ CORPORATION Address: 157 Shan-Ying Road Kweishan Taoyuan 333 TAIWAN, R.O.C. Attention: George Chiou Technical Manager • FCC ID: JVPH0523 • Quantity: Quantity production is planned • Emission Designators: 40K0F8W / 40K0F1D (AMPS), 1M25F9W (CDMA) • Tx Freq. Range: 824.04 — 848.97 MHz (AMPS) 824.70 — 848.31 MHz (CDMA) 1851.25 — 1908.75 MHz (PCS CDMA) • Rx Freq. Range: 869.04 — 893.97 MHz (AMPS) 869.70 — 893.31 MHz (CDMA) 1931.25 — 1988.75 MHz (PCS CDMA) • Max. Power Rating: 0.606 W ERP AMPS (27.823 dBm) / 0.388 W ERP CDMA (25.883 dBm) 0.396 W EIRP PCS CDMA (25.981 dBm) • FCC Classification(s): Licensed Portable Tx Held to Ear (PCE) • Equipment (EUT) Type: Tri-Mode Dual-Band Analog/PCS Phone • Modulation(s): AMPS / CDMA • Frequency Tolerance: ± 0.00025% (2.5 ppm) • FCC Rule Part(s): § 24(E), §22(H), §22.901(d) • Dates of Tests: June 5-7, 2002 • Place of Tests: PCTEST Lab, Columbia, MD U.S.A. • Test Report S/N: 22/24.220605283.JVP FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 3 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

2.1 INTRODUCTION These measurement tests were conducted at PCTEST Engineering Laboratory, Inc. facility in New Concept Business Park, Guilford Industrial Park, Columbia, Maryland. The site address is 6660-B Dobbin Road, Columbia, MD 21045. The test site is one of the highest points in the Columbia area with an elevation of 390 feet above mean sea level. The site coordinates are 39° 11'15" N latitude and 76° 49'38" W longitude. The facility is 1.5 miles North of the FCC laboratory, and the ambient signal and ambient signal strength are approximately equal to those of the FCC laboratory. There are no FM or TV transmitters within 15 miles of the site. The detailed description of the measurement facility was found to be in compliance with the requirements of § 2.948 according to ANSI C63.4 on October 19, 1992. Figure 1. Map of the Greater Baltimore and Metropolitan Washington, D.C. area. Measurement Procedure The radiated and spurious measurements were made outdoors at a 3-meter test range (see Figure2). The equipment under test is placed on a wooden turntable 3-meters from the receive antenna. The receive antenna height and turntable rotations were adjusted for the highest reading on the receive spectrum analyzer. A half- wave dipole was substituted in place of the EUT. This dipole antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same receive spectrum analyzer reading. This level is recorded. For readings above 1GHz, the above procedure is repeated using horn antennas and the difference between the gain of the horn and an isotropic antenna are taken into consideration. Figure 2. Diagram of 3-meter outdoor test range FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 4 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

3.1 INSERTS Function of Active Devices (Confidential) The Function of active devices are shown in Attachment K. Block & Schematic Diagrams (Confidential) The block diagrams are shown in Attachment I, and the schematic diagrams are shown in Attachment J. Operating Instructions The instruction manual is shown in Attachment M. Parts List & Tune-Up Procedure (Confidential) The parts list & tune-up procedure is shown in Attachment L. Description of Freq. Stabilization Circuit (Confidential) The description of frequency stabilization circuit is shown in Attachment K. Description for Suppression of Spurious Radiation, for Limiting Modulation, and Harmonic Suppresion Circuits (Confidential) The description of suppression stabilization circuits is shown in Attachment K. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 5 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

4.1 DESCRIPTION OF TESTS 4.2 Transmitter Audio Frequency Response The frequency response of the audio modulating circuit over the frequency range 100 — 5000 Hz is measured. The audio signal generator is connected to the audio input circuit/microphone of the EUT. The audio signal input is adjusted to obtain 50% modulation at 1kHz and this point is taken as the 0dB reference. With the input held constant and below the limit at all frequencies, the audio signal generator is varied from 100 to 50 kHz. 4.3 Audio Low Pass Filter Frequency Response The response in dB relative to 1kHz is measured using the HP8901 a Modulation Analyzer. For the frequency response of the audio low-pass filter, the audio input is connected at the input to the modulation limiter and the modulated stage. The audio output is connected at the output of the modulated stage. The corresponding plots are shown herein. 4.4 Modulation Limiting The audio signal generator is connected to the audio input circuit/microphone of the EUT. The modulation response is measured for each of the three modulating frequencies (300Hz, 1000 Hz, and 3000Hz), and the input voltage is varied from 30% modulation (±3.6kHz deviation) to at least 20dB higher than the saturation point. Measurements of modulation and the plots are attached herein. Measurements were performed for ST, SAT, and wide-band data modulations. The corresponding results are shown herein. Note: ST, SAT, & Wide-Band data were internally generated by the EUT. EUT HP 8901A HP 8903B HP 8903B Modulation Audio Audio Generator Analyzer Analyzer Fig. 3. Transmitter Audio Frequency & Tone Modulation Test Setup. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 6 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

4.1 DESCRIPTION OF TESTS (CONTINUED) 4.5 Occupied Bandwidth Emission Limits (a) On any frequency outside a licensee’s frequency block, the power of any emission shall be attenuated below the transmitter power (P) by at least 43 + 10 log(P) dB. (b) Compliance with these provisions is based on the use of measurement instrumentation employing a resolution bandwidth of 1 MHz or greater. However, in the 1 MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed. The emission bandwidth is defined as the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, outside of which all emission are attenuated at least 26 dB below the transmitter power. (c) When measuring the emission limits, the nominal carrier frequency shall be adjusted as close to the licensee’s frequency block edges, both upper and lower, as the design permits. (d) The measurement of emission power can be expressed in peak or average values, provided they are expressed in the same parameters as the transmitter power. BLOCK Freq. Range (MHz) Freq. Range (MHz) Transmitter (Tx) Receiver (Rx) A 1850 - 1865 1930 - 1945 B 1870 - 1885 1950 - 1965 C 1895 - 1910 1975 - 1990 D 1865 - 1870 1945 - 1950 E 1885 - 1890 1965 - 1970 F 1890 - 1895 1970 - 1975 Table 1. Broadband PCS Service Frequency Blocks. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 7 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

4.1 DESCRIPTION OF TESTS (CONTINUED) 4.6 Occupied Bandwidth The audio signal generator is adjusted to 1kHz. The output level is set to ±6kHz deviation. With the level constant, the frequency is set to 2500Hz. Then the audio signal level is increased by 16dB. The occupied bandwidth data is obtained for the SAT (Supervisory Audio Tone), ST (Signaling Tone), WBD (Wideband data), and DTMF (Dual Tone Multi Frequencies). The results are shown on the attached graphs. Specified Limits: a. On any frequency removed from the assigned carrier frequency by more than 20 kHz, up to and including 45kHz, the sideband is at least 26dB below the carrier. b. On any frequency removed from the assigned carrier frequency by more than 45 kHz, up to and including 90kHz, the sideband is at least 45dB below the carrier. c. On any frequency removed from the assigned carrier frequency by more than 90 kHz, up to the first multiple of the carrier frequency, the sideband is at least 60dB below the carrier or 40 + log10 (mean power output in Watts) dB, whichever is the smaller attenuation. 4.7 Spurious and Harmonic Emissions at Antenna Terminal The level of the carrier and the various conducted spurious and harmonic frequencies is measured by means of a calibrated spectrum analyzer. The spectrum is scanned from the lowest frequency generated in the equipment up to 10 GHz. The transmitter is modulated with a 2500Hz tone at a level of 16dB greater than that required to provided 50% modulation. At the input terminals of the spectrum analyzer, an isolator (RF circulator with on port terminated with 50 ohms) and an 870 MHz to 890 MHz bandpass filter is connected between the test transceiver (for conducted tests) or the receive antenna (for radiated tests) and the analyzer. The rejection of the bandpass filter to signals in the 825 — 845 MHz range is adequate to limit the transmit energy from the test transceiver which appears to a level which will allow the analyzer to measure signals less than — 90dBm. Calibration of the test receiver is performed in the 870 — 890 MHz range to insure accuracy to allow variation in the bandpass filter insertion loss to be calibrated. 4.8 Frequencies At the input terminals of the spectrum analyzer, an isolator (RF pad) and an high-pass filter are connected between the test transceiver (for conducted tests) or the receive antenna (for radiated tests) and the analyzer. The high-pass filter (signals below 1.6 GHz) is to limit the fundamental frequency from interfering with the measurement of low-level spurious and harmonic emissions and to ensure that the preamplifier is not saturated. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 8 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

4.9 Radiation Spurious and Harmonic Emissions Radiation and harmonic emissions are measured outdoors at our 3-meter test range. The equipment under test is placed on a wooden turntable 3-meters from the receive antenna. The receive antenna height and turntable rotations were adjusted for the highest reading on the receive spectrum analyzer. A half-wave dipole was substituted in place of the EUT. This dipole antenna was driven by a signal generator with the level of the signal generator being adjusted to obtain the same receive spectrum analyzer reading. This level is recorded. For readings above 1GHz, the above procedure is repeated using horn antennas and the difference between the gain of the horn and an isotropic or dipole antenna are taken into consideration. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 9 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

5.0 Frequency Stability/Temperature Variation. The frequency stability of the transmitter is measured by: a.) Temperature: The temperature is varied from -30°C to +60°C using an environmental chamber. b.) Primary Supply Voltage: The primary supply voltage is varied from 85% to 115% of the voltage normally at the input to the device or at the power supply terminals if cables are not normally supplied. Specification — The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized frequency block. The frequency stability of the transmitter shall be maintained within ±0.00025 (±2.5 ppm) of the center frequency. Time Period and Procedure: 1. The carrier frequency of the transmitter and the individual oscillators is measured at room temperature (25°C to 27°C to provide a reference). 2. The equipment is subjected to an overnight “soak” at -30°C without any power applied. 3. After the overnight “soak” at 30°C (usually 14-16 hours), the equipment is turned on in a “standby” condition for one minute before applying power to the transmitter. Measurement of the carrier frequency of the transmitter and the individual oscillators is made within a three minute interval after applying power to the transmitter. 4. Frequency measurements are made at 10°C interval up to room temperature. At least a period of one and one half-hour is provided to allow stabilization of the equipment at each temperature level. 5. Again the transmitter carrier frequency and the individual oscillators is measured at room temperature to begin measurement of the upper temperature levels. 6. Frequency measurements are at 10 intervals starting at 30°C up to +50°C allowing at least two hours at each temperature for stabilization. In all measurements the frequency is measured within three minutes after re-applying power to the transmitter. 7. The artificial load is mounted external to the temperature chamber. NOTE: The EUT is tested down to the battery endpoint. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 10 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

5.1 Test Data 5.2 Effective Radiated Power Output A. POWER: Low (Analog Mode) REF. Freq. Tuned POL ERP ERP LEVEL (MHz) (dBm) (H/V) (W) (dBm) 824.04 -33.450 H 0.006 7.823 836.49 -33.650 H 0.006 7.779 848.97 -33.900 H 0.006 7.685 B. POWER: High (Analog Mode) REF. Freq. Tuned POL ERP ERP BATTERY LEVEL (MHz) (dBm) (H/V) (W) (dBm) 824.04 -13.450 H 0.60580 27.823 Standard 836.49 -13.650 H 0.60021 27.783 Standard 848.97 -13.900 H 0.58654 27.683 Standard Note: Standard batteries are the only options for this phone NOTES: Effective Radiated Power Output Measurements by Substitution Method according to ANSI/TIA/EIA-603-A-2001, Aug. 15, 2001: The EUT was placed on a wooden turn table 3-meters from the receive antenna. The receive antenna height and turntable rotation was adjusted for the highest reading on the receive spectrum analyzer. A half-wave dipole was substituted in place of the EUT. This dipole antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same receive spectrum analyzer reading. The conducted power at the terminals of the dipole is measured. The ERP is recorded. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 11 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

5.1 Test Data 5.3 Effective Radiated Power Output A. POWER: High (CDMA Mode) REF. Freq. Tuned POL ERP ERP BATTERY LEVEL (MHz) (dBm) (H/V) (W) (dBm) 824.70 -15.400 H 0.38753 25.883 Standard 835.89 -15.700 H 0.37435 25.733 Standard 848.31 -15.900 H 0.36923 25.673 Standard Note: Standard batteries are the only options for this phone NOTES: Effective Radiated Power Output Measurements by Substitution Method according to ANSI/TIA/EIA-603-A-2001, Aug. 15, 2001: The EUT was placed on a wooden turn table 3-meters from the receive antenna. The receive antenna height and turntable rotation was adjusted for the highest reading on the receive spectrum analyzer. A half-wave dipole was substituted in place of the EUT. This dipole antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same receive spectrum analyzer reading. The conducted power at the terminals of the dipole is measured. The ERP is recorded. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 12 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

6.1 Test Data 6.2 Equivalent Isotropic Radiated Power (E.I.R.P.) Radiated measurements at 3 meters Supply Voltage: 3.7 VDC Modulation: PCS CDMA REF. FREQ. POL Azimuth EIRP EIRP Battery LEVEL (MHz) (dBm) (H/V) (o angle) (dBm) (W) 1851.25 -17.100 H 60 25.981 0.396 Standard 1880.00 -17.400 H 60 25.851 0.385 Standard 1908.75 -17.700 H 60 25.721 0.373 Standard Note: Standard batteries are the only options for this phone NOTES: Equivalent Isotropic Radiated Power Measurements by Substitution Method according to ANSI/TIA/EIA-603-A-2001, Aug. 15, 2001: The EUT was placed on a wooden turn table 3-meters from the receive antenna. The receive antenna height and turntable rotation was adjusted for the highest reading on the receive spectrum analyzer. A Horn antenna was substituted in place of the EUT. This Horn antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same receive spectrum analyzer reading. The conducted power at the terminals of the Horn antenna is measured. The difference between the gain of the horn and an isotropic antenna is taken into consideration and the EIRP is recorded. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 13 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

7.1 Test Data 7.2 AMPS Radiated Measurements Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 824.04 MHz CHANNEL: 0991 (Low) MEASURED OUTPUT POWER: 27.823 dBm = 0.606 W MODULATION SIGNAL: FM (Internal) DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 40.82 dBc REFERENCE FREQ. POL LEVEL (MHz) (dBm) (H/V) (dBc) 1648.08 -40.88 H 68.7 2472.12 -44.58 H 72.4 3296.16 -53.38 H 81.2 4120.20 -60.78 H 88.6 4944.24 -68.38 H 96.2 NOTES: Radiated Spurious Emission Measurements by Substitution Method according to ANSI/TIA/EIA-603-A-2001, Aug. 15, 2001: The EUT was placed on a wooden turn table 3-meters from the receive antenna. The receive antenna height and turntable rotation was adjusted for the highest reading on the receive spectrum analyzer. A half-wave dipole was substituted in place of the EUT. This dipole antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same receive spectrum analyzer reading. This spurious level is recorded. For readings above 1GHz, the above procedure is repeated using horn antennas and the difference between the gain of the horn and an isotropic or dipole antenna are taken into consideration. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 14 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

7.1 Test Data (Continued) 7.3 AMPS Radiated Measurements Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 836.49 MHz CHANNEL: 0383 (Mid) MEASURED OUTPUT POWER: 27.823 dBm = 0.606 W MODULATION SIGNAL: FM (Internal) DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 40.82 dBc REFERENCE FREQ. POL LEVEL (MHz) (dBm) (H/V) (dBc) 1672.98 -46.38 H 74.2 2509.47 -49.88 H 77.7 3345.96 -57.68 H 85.5 4182.45 -63.18 H 91.0 5018.94 -71.88 H 99.7 NOTES: Radiated Spurious Emission Measurements by Substitution Method according to ANSI/TIA/EIA-603-A-2001, Aug. 15, 2001: The EUT was placed on a wooden turn table 3-meters from the receive antenna. The receive antenna height and turntable rotation was adjusted for the highest reading on the receive spectrum analyzer. A half-wave dipole was substituted in place of the EUT. This dipole antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same receive spectrum analyzer reading. This spurious level is recorded. For readings above 1GHz, the above procedure is repeated using horn antennas and the difference between the gain of the horn and an isotropic or dipole antenna are taken into consideration. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 15 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

7.1 Test Data (Continued) 7.4 AMPS Radiated Measurements Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 848.97 MHz CHANNEL: 0799 (High) MEASURED OUTPUT POWER: 27.823 dBm = 0.606 W MODULATION SIGNAL: FM (Internal) DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 40.82 dBc REFERENCE FREQ. POL LEVEL (MHz) (dBm) (H/V) (dBc) 1697.94 -47.48 H 75.3 2546.91 -52.48 H 80.3 3395.88 -62.23 H 90.1 4244.85 -65.28 H 93.1 NOTES: Radiated Spurious Emission Measurements by Substitution Method according to ANSI/TIA/EIA-603-A-2001, Aug. 15, 2001: The EUT was placed on a wooden turn table 3-meters from the receive antenna. The receive antenna height and turntable rotation was adjusted for the highest reading on the receive spectrum analyzer. A half-wave dipole was substituted in place of the EUT. This dipole antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same receive spectrum analyzer reading. This spurious level is recorded. For readings above 1GHz, the above procedure is repeated using horn antennas and the difference between the gain of the horn and an isotropic or dipole antenna are taken into consideration. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 16 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

7.1 Test Data (Continued) 7.5 CELLULAR CDMA Radiated Measurements Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 824.70 MHz CHANNEL: 1013 (Low) MEASURED OUTPUT POWER: 25.883 dBm = 0.388 W MODULATION SIGNAL: CDMA (Internal) DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 38.88 dBc REFERENCE FREQ. POL LEVEL (MHz) (dBm) (H/V) (dBc) 1649.40 -42.78 H 68.7 2474.10 -49.38 H 75.3 3298.80 -53.38 H 79.3 4123.50 -64.18 H 90.1 4948.20 -70.38 H 96.3 NOTES: Radiated Spurious Emission Measurements by Substitution Method according to ANSI/TIA/EIA-603-A-2001, Aug. 15, 2001: The EUT was placed on a wooden turn table 3-meters from the receive antenna. The receive antenna height and turntable rotation was adjusted for the highest reading on the receive spectrum analyzer. A half-wave dipole was substituted in place of the EUT. This dipole antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same receive spectrum analyzer reading. This spurious level is recorded. For readings above 1GHz, the above procedure is repeated using horn antennas and the difference between the gain of the horn and an isotropic or dipole antenna are taken into consideration. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 17 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

7.1 Test Data (Continued) 7.6 CELLULAR CDMA Radiated Measurements Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 835.89 MHz CHANNEL: 0383 (Mid) MEASURED OUTPUT POWER: 25.883 dBm = 0.388 W MODULATION SIGNAL: CDMA (Internal) DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 38.88 dBc REFERENCE FREQ. POL LEVEL (MHz) (dBm) (H/V) (dBc) 1671.78 -46.18 H 72.1 2507.67 -52.08 H 78.0 3343.56 -58.18 H 84.1 4179.45 -62.28 H 88.2 NOTES: Radiated Spurious Emission Measurements by Substitution Method according to ANSI/TIA/EIA-603-A-2001, Aug. 15, 2001: The EUT was placed on a wooden turn table 3-meters from the receive antenna. The receive antenna height and turntable rotation was adjusted for the highest reading on the receive spectrum analyzer. A half-wave dipole was substituted in place of the EUT. This dipole antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same receive spectrum analyzer reading. This spurious level is recorded. For readings above 1GHz, the above procedure is repeated using horn antennas and the difference between the gain of the horn and an isotropic or dipole antenna are taken into consideration. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 18 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

7.1 Test Data (Continued) 7.7 CELLULAR CDMA Radiated Measurements Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 848.31 MHz CHANNEL: 0777 (High) MEASURED OUTPUT POWER: 25.883 dBm = 0.388 W MODULATION SIGNAL: CDMA (Internal) DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 38.88 dBc REFERENCE FREQ. POL LEVEL (MHz) (dBm) (H/V) (dBc) 1696.62 -47.88 H 73.8 2544.93 -56.78 H 82.7 3393.24 -60.28 H 86.2 4241.55 -70.78 H 96.7 NOTES: Radiated Spurious Emission Measurements by Substitution Method according to ANSI/TIA/EIA-603-A-2001, Aug. 15, 2001: The EUT was placed on a wooden turn table 3-meters from the receive antenna. The receive antenna height and turntable rotation was adjusted for the highest reading on the receive spectrum analyzer. A half-wave dipole was substituted in place of the EUT. This dipole antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same receive spectrum analyzer reading. This spurious level is recorded. For readings above 1GHz, the above procedure is repeated using horn antennas and the difference between the gain of the horn and an isotropic or dipole antenna are taken into consideration. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 19 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

7.1 Test Data (Continued) 7.8 PCS CDMA Radiated Measurements Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 1851.25 MHz CHANNEL: 0025 (Low) MEASURED OUTPUT POWER: 25.981 dBm = 0.396 W MODULATION SIGNAL: CDMA (Internal) DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 38.98 dBc REFERENCE FREQ. POL LEVEL (MHz) (dBm) (H/V) (dBc) 3702.50 -30.83 H 56.8 5553.75 -35.03 H 61.0 7405.00 -39.53 H 65.5 9256.25 -56.03 H 82.0 NOTES: Radiated Spurious Emission Measurements by Substitution Method according to ANSI/TIA/EIA-603-A-2001, Aug. 15, 2001: The EUT was placed on a wooden turn table 3-meters from the receive antenna. The receive antenna height and turntable rotation was adjusted for the highest reading on the receive spectrum analyzer. A half-wave dipole was substituted in place of the EUT. This dipole antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same receive spectrum analyzer reading. This spurious level is recorded. For readings above 1GHz, the above procedure is repeated using horn antennas and the difference between the gain of the horn and an isotropic or dipole antenna are taken into consideration. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 20 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

7.1 Test Data (Continued) 7.9 PCS CDMA Radiated Measurements Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 1880.00 MHz CHANNEL: 0600 (Mid) MEASURED OUTPUT POWER: 25.981 dBm = 0.396 W MODULATION SIGNAL: CDMA (Internal) DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 38.98 dBc REFERENCE FREQ. POL LEVEL (MHz) (dBm) (H/V) (dBc) 3760.00 -33.23 H 59.2 5640.00 -39.33 H 65.3 7520.00 -45.73 H 71.7 9400.00 -54.63 H 80.6 NOTES: Radiated Spurious Emission Measurements by Substitution Method according to ANSI/TIA/EIA-603-A-2001, Aug. 15, 2001: The EUT was placed on a wooden turn table 3-meters from the receive antenna. The receive antenna height and turntable rotation was adjusted for the highest reading on the receive spectrum analyzer. A half-wave dipole was substituted in place of the EUT. This dipole antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same receive spectrum analyzer reading. This spurious level is recorded. For readings above 1GHz, the above procedure is repeated using horn antennas and the difference between the gain of the horn and an isotropic or dipole antenna are taken into consideration. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 21 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

7.1 Test Data (Continued) 7.10 PCS CDMA Radiated Measurements Field Strength of SPURIOUS Radiation OPERATING FREQUENCY: 1908.75 MHz CHANNEL: 1175 (High) MEASURED OUTPUT POWER: 25.981 dBm = 0.396 W MODULATION SIGNAL: CDMA (Internal) DISTANCE: 3 meters LIMIT: 43 + 10 log10 (W) = 38.98 dBc REFERENCE FREQ. POL LEVEL (MHz) (dBm) (H/V) (dBc) 3817.50 -35.23 H 61.2 5726.25 -46.13 H 72.1 7635.00 -51.13 H 77.1 9543.75 -59.53 H 85.5 NOTES: Radiated Spurious Emission Measurements by Substitution Method according to ANSI/TIA/EIA-603-A-2001, Aug. 15, 2001: The EUT was placed on a wooden turn table 3-meters from the receive antenna. The receive antenna height and turntable rotation was adjusted for the highest reading on the receive spectrum analyzer. A half-wave dipole was substituted in place of the EUT. This dipole antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same receive spectrum analyzer reading. This spurious level is recorded. For readings above 1GHz, the above procedure is repeated using horn antennas and the difference between the gain of the horn and an isotropic or dipole antenna are taken into consideration. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 22 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

8.1 Test Data 8.2 FREQUENCY STABILITY (AMPS) OPERATING FREQUENCY: 836,490,003 Hz CHANNEL: 383 REFERENCE VOLTAGE: 3.7 VDC DEVIATION LIMIT: ± 0.00025 % or 2.5 ppm VOLTAGE POWER TEMP FREQ. Deviation (%) (VDC) (ºC) (Hz) (%) 100 % 3.70 + 20 (Ref) 836,490,003 0.000000 100 % - 30 836,489,886 0.000014 100 % - 20 836,489,903 0.000012 100 % - 10 836,489,919 0.000010 100 % 0 836,489,936 0.000008 100 % + 10 836,489,970 0.000004 100 % + 20 836,490,003 0.000000 100 % + 25 836,489,961 0.000005 100 % + 30 836,490,020 -0.000002 100 % + 40 836,490,036 -0.000004 100 % + 50 836,490,078 -0.000009 100 % + 60 836,490,112 -0.000013 85 % 3.17 + 20 836,490,003 0.000000 115 % 4.26 + 20 836,490,003 0.000000 BATT. ENDPOINT 3.03 + 20 836,490,003 0.000000 FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 23 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

8.1 Test Data (Continued) 8.3 FREQUENCY STABILITY (AMPS) Frequency Stability 3.5 2.5 1.5 Deviation (ppm) 0.5 -0.5 -1.5 -2.5 -3.5 -20 - 30 - 20 - 10 0 + 10 + 20 + 25 + 30 + 40 + 50 + 60 + 20 + 20 + 20 Temperature (°C) FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 24 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

8.1 Test Data (Continued) 8.4 FREQUENCY STABILITY (PCS CDMA) OPERATING FREQUENCY: 1,880,000,005 Hz CHANNEL: 600 REFERENCE VOLTAGE: 3.7 VAC DEVIATION LIMIT: ± 0.00025 % or 2.5 ppm VOLTAGE POWER TEMP FREQ. Deviation (%) (VDC) (ºC) (Hz) (%) 100 % 3.70 + 20 (Ref) 1,880,000,005 0.000000 100 % - 30 1,879,999,817 0.000010 100 % - 20 1,879,999,836 0.000009 100 % - 10 1,879,999,817 0.000010 100 % 0 1,879,999,855 0.000008 100 % + 10 1,879,999,911 0.000005 100 % + 20 1,880,000,005 0.000000 100 % + 25 1,879,999,949 0.000003 100 % + 30 1,879,999,836 0.000009 100 % + 40 1,880,000,193 -0.000010 100 % + 50 1,880,000,174 -0.000009 100 % + 60 1,880,000,193 -0.000010 85 % 3.17 + 20 1,880,000,005 0.000000 115 % 4.26 + 20 1,880,000,005 0.000000 BATT. ENDPOINT 3.03 + 20 1,880,000,005 0.000000 FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 25 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

8.1 Test Data (Continued) 8.5 FREQUENCY STABILITY (PCS CDMA) Frequency Stability 3.5 2.5 1.5 Deviation (ppm) 0.5 -0.5 -1.5 -2.5 -3.5 -20 - 30 - 20 - 10 0 + 10 + 20 + 25 + 30 + 40 + 50 + 60 + 20 + 20 + 20 Temperature (°C) FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 26 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

PCTEST* PeTEST rouueninumnium Bena,

10.1 TEST EQUIPMENT Type Model Cal. Due Date S/N Microwave Spectrum Analyzer HP 8566B (100Hz-22GHz) 08/15/02 3638A08713 Microwave Spectrum Analyzer HP 8566B (100Hz-22GHz) 04/17/03 2542A11898 Spectrum Analyzer/Tracking Gen. HP 8591A (100Hz-1.8GHz) 08/10/02 3144A02458 Signal Generator* HP 8640B (500Hz-1GHz) 06/03/03 2232A19558 Signal Generator* HP 8640B (500Hz-1GHz) 06/03/03 1851A09816 Signal Generator* Rohde & Schwarz (0.1-1000MHz) 09/11/02 894215/012 Ailtech/Eaton Receiver NM 37/57A-SL (30-1000MHz) 04/12/03 0792-03271 Ailtech/Eaton Receiver NM 37/57A (30-1000MHz) 03/11/03 0805-03334 Ailtech/Eaton Receiver NM 17/27A (0.1-32MHz) 09/17/02 0608-03241 Quasi-Peak Adapter HP 85650A 08/15/02 2043A00301 Ailtech/Eaton Adapter CCA-7 CISPR/ANSI QP Adapter 03/11/03 0194-04082 Gigatronics Universal Power Meter 8657A 1835256 Gigatronics Power Sensor 80701A (0.05-18GHz) 1833460 Signal Generator HP 8648D (9kHz-4GHz) 3613A00315 Amplifier Research 5S1G4 (5W, 800MHz-4.2GHz) 22322 Network Analyzer HP 8753E (30kHz-3GHz) JP38020182 Audio Analyzer HP 8903B 3011A09025 Modulation Analyzer HP 8901A 2432A03467 Power Meter HP 437B 3125U24437 Power Sensor HP 8482H (30µW-3W) 2237A02084 Harmonic/Flicker Test System HP 6841A (IEC 555-2/3) 3531A00115 Broadband Amplifier (2) HP 8447D 1145A00470, 1937A03348 Broadband Amplifier HP 8447F 2443A03784 Horn Antenna EMCO Model 3115 (1-18GHz) 9704-5182 Horn Antenna EMCO Model 3115 (1-18GHz) 9205-3874 Horn Antenna EMCO Model 3116 (18-40GHz) 9203-2178 Biconical Antenna (4) Eaton 94455/Eaton 94455-1/Singer 94455-1/Compliance Design 1295, 1332, 0355 Log-Spiral Antenna (3) Ailtech/Eaton 93490-1 0608, 1103, 1104 Roberts Dipoles Compliance Design (1 set) Ailtech Dipoles DM-105A (1 set) 33448-111 EMCO LISN (6) 3816/2 1079 Microwave Preamplifier 40dB Gain HP 83017A (0.5-26.5GHz) 3123A00181 Microwave Cables MicroCoax (1.0-26.5GHz) Ailtech/Eaton Receiver NM37/57A-SL 0792-03271 Spectrum Analyzer HP 8594A 3051A00187 Spectrum Analyzer (2) HP 8591A 3034A01395, 3108A02053 Microwave Survey Meter Holaday Model 1501 (2.450GHz) 80931 Digital Thermometer Extech Instruments 421305 426966 Attenuator HP 8495A (0-70dB) DC-4GHz Bi-Directional Coax Coupler Narda 3020A (50-1000MHz) Shielded Screen Room RF Lindgren Model 26-2/2-0 6710 (PCT270) Shielded Semi-Anechoic Chamber Ray Proof Model S81 R2437 (PCT278) Enviromental Chamber Associated Systems Model 1025 (Temperature/Humidity) PCT285 * Calibration traceable to the National Institute of Standards and Technology (NIST). FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 28 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

11.1 SAMPLE CALCULATIONS A. Emission Designator Emission Designator = 1M25F9W CDMA BW = 1.25 MHz F = Frequency Modulation 9 = Composite Digital Info W = Combination (Audio/Data) (Measured at the 99.75% power bandwidth) Emission Designator = 40K0F8W Calculation: Voice + SAT Modulation: Voice is 2.5 kHz and SAT is 6 kHz — Maximum modulation is M = 6 kHz Deviation: Voice is 12 kHz and SAT is 2 kHz — Maximum deviation is D = 12 + 2 = 14 kHz Bn = 2xM + 2xDK with K = 1 Bn = 40 kHz Calculation: Signaling Tone (ST) + SAT Modulation: ST is 10 kHz and SAT is 6 kHz — Maximum modulation is M = 10 kHz Deviation: ST is 8 kHz and SAT is 2 kHz — Maximum deviation is D = 8 + 2 = 10 kHz Bn = 2xM + 2xDK with K = 1 Bn = 40 kHz Emission Designator = 40K0F1D Calculation: Voice + SAT Modulation: Wideband Data is 10 kHz and SAT is 6 kHz — Maximum modulation is M = 10 kHz Deviation: Wideband Data is 8 kHz and SAT is 2 kHz — Maximum deviation is D = 8 + 2 = 10 kHz Bn = 2xM + 2xDK with K = 1 Bn = 40 kHz B. Spurious Radiated Emission - PCS Band Example: Channel 25 PCS Mode 2nd Harmonic (3702.50 MHz) The receive analyzer reading at 3 meters with the EUT on the turntable was —81.0 dBm. The gain of the substituted antenna is 8.1 dBi. The signal generator connected to the substituted antenna terminals is adjusted to produce a reading of —81.0 dBm on the receive analyzer. The loss of the cable between the signal generator and the terminals of the substituted antenna is 2.0 dB at 3702.50 MHz. So 6.1 dB is added to the signal generator reading of —30.9 dBm yielding —24.80 dBm. The fundamental EIRP was 25.501 dBm so this harmonic was 25.501 dBm — (-24.80) = 50.3 dBc FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 29 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.

12.1 CONCLUSION The data collected shows that the BENQ Tri-Mode Dual-Band Analog/PCS Phone (AMPS/CDMA) FCC ID: JVPH0523 complies with all the requirements of Parts 2, 22, and 24 of the FCC rules. FCC CERTIFICATION Reviewed By: PCTEST PT. 22/24 REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: FCC ID: Page 30 of 30 22/24.220605283.JVP June 5-7, 2002 Tri-Mode Dual-Band Phone JVPH0523 © 2002 PCTEST ENGINEERING LABORATORY, INC.


Document Created: 2002-07-18 16:54:27
Document Modified: 2002-07-18 16:54:27
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC