SAR Test Report

FCC ID: JUPTRIMTRACE

RF Exposure Info

Download: PDF
FCCID_833385

IN ACCORDANCE WITH THE REQUIREMENTS OF FCC OET BULLETIN 65 SUPPLEMENT C FOR TrimTrac Pro E MODEL: 80200-00 FCC ID: JUPTRIMTRACE REPORT NUMBER: 07U11144-1 ISSUE DATE: JUNE 29, 2007 Prepared for Trimble Navigation Limited 510 DeGuigne Dr. Sunnyvale, CA 94085 Prepared by COMPLIANCE CERTIFICATION SERVICES 47173 BENICIA STREET, FREMONT, CA 94538 USA

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE Revision History Rev. Issued date Revisions Revised By -- June 29, 2007 Initial issue Sunny Shih COMPLIANCE CERTIFICATION SERVICES Page: 2 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE CERTIFICATE OF COMPLIANCE (SAR EVALUATION) DATES OF TEST: June 21 - 22, 2007 APPLICANT: Trimble Navigation Limited ADDRESS: 510 DeGuigne Dr. Sunnyvale, CA 94085 FCC ID: JUPTRIMTRACE MODEL: 80200-00 DEVICE CATEGORY: Portable Device EXPOSURE CATEGORY: General Population/Uncontrolled Exposure TrimTrac Pro E operates at GSM850 & GSM1900 US bands. Test Sample is a: Production unit The Highest Rule Parts Frequency Range [MHz] SAR Values [1g_mW/g] FCC 22H 824.2 - 848.8 0.645 FCC 24E 1850.20 - 1909.8 0.375 This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for General Population/Uncontrolled Exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in FCC OET 65 Supplement C (Edition 01-01). This wireless device has been shown to be capable of compliance for localized specific absorption rate (SAR) for General Population/Uncontrolled Exposure limits specified and tested in accordance with procedures referenced below in Section 2. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by Compliance Certification Services and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by Compliance Certification Services will constitute fraud and shall nullify the document. No part of this report may be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any government agency. Approved & Released For CCS By: Tested By: Hsin Fu Shih Ninous Davoudi Engineering Supervisor EMC Engineer Compliance Certification Services Compliance Certification Services COMPLIANCE CERTIFICATION SERVICES Page: 3 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE TABLE OF CONTENTS 1 DEVICE UNDER TEST (DUT) DESCRIPTION ................................................................................... 5 2 FACILITIES AND ACCREDITATION ................................................................................................... 6 3 SYSTEM DESCRIPTION ..................................................................................................................... 7 3.1 COMPOSITION OF INGREDIENTS FOR TISSUE SIMULATING LIQUIDS .............................. 8 4 SIMULATING LIQUID PARAMETERS CHECK................................................................................... 9 4.1 SIMULATING LIQUID PARAMETER CHECK RESULT............................................................ 10 5 SYSTEM PERFORMANCE CHECK .................................................................................................. 13 5.1 SYSTEM PERFORMANCE CHECK RESULTS........................................................................ 14 6 SAR MEASURMENT PROCEDURE ................................................................................................. 15 6.1 DASY4 SAR MEASURMENT PROCEDURE ............................................................................ 16 7 PROCEDURE USED TO ESTABLISH TEST SIGNAL ...................................................................... 17 8 SAR MEASURMENT RESULTS........................................................................................................ 18 8.1 CELL BAND ............................................................................................................................... 18 8.1.1 POSITION 1 & 2...................................................................................................................... 18 8.1.2 POSITION 3 & 4...................................................................................................................... 19 8.1.3 POSITION 5 & 6...................................................................................................................... 20 8.2 PCS BAND................................................................................................................................. 21 8.2.1 POSITION 1 & 2...................................................................................................................... 21 8.2.2 POSITION 3 & 4...................................................................................................................... 22 8.2.3 POSITION 5 & 6...................................................................................................................... 23 9 MEASURMENT UNCERTAINTY ....................................................................................................... 24 9.1 MEASURMENT UNCERTAINTY FOR 300 MHZ – 3000 MHZ ................................................. 24 10 EQUIPMENT LIST AND CALIBRATION............................................................................................ 25 11 PHOTOS ............................................................................................................................................ 26 12 ATTACHMENTS................................................................................................................................. 29 COMPLIANCE CERTIFICATION SERVICES Page: 4 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 1 DEVICE UNDER TEST (DUT) DESCRIPTION TrimTrac Pro E operates at GSM850 & GSM1900 US bands. Normal operation: Body position Accessories: N/A Earphone/Headset Jack: N/A Duty cycle: 12.5% Power supply: • Disposable battery - AA Alkaline battery x 4, rating 1.5 Vdc • Rechargeable battery - Lexel, LH070-3A44C3BROT, 3.6 Vdc, 700 mAh. COMPLIANCE CERTIFICATION SERVICES Page: 5 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 2 FACILITIES AND ACCREDITATION The test sites and measurement facilities used to collect data are located at 47173 Benicia Street, Fremont, CA 94538 USA. The sites are constructed in conformance with the requirements of ANSI C63.4, ANSI C63.7 and CISPR Publication 22. All receiving equipment conforms to CISPR Publication 16-1, “Radio Interference Measuring Apparatus and Measurement Methods.” CCS is accredited by NVLAP, Laboratory Code 200065-0. The full scope of accreditation can be viewed at http://www.ccsemc.com. No part of this report may be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any government agency. COMPLIANCE CERTIFICATION SERVICES Page: 6 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 3 SYSTEM DESCRIPTION The DASY4 system for performing compliance tests consists of the following items: • A standard high precision 6-axis robot (Stäubli RX family) with controller, teach pendant and software. An arm extension for accommodating the data acquisition electronics (DAE). • A dosimetric probe, i.e., an isotropic E-field probe optimized and calibrated for usage in tissue simulating liquid. The probe is equipped with an optical surface detector system. • A data acquisition electronics (DAE) which performs the signal amplification, signal multiplexing, AD-conversion, offset measurements, mechanical surface detection, collision detection, etc. The unit is battery powered with standard or rechargeable batteries. The signal is optically transmitted to the EOC. • The function of the measurement server is to perform the time critical tasks such as signal filtering, control of the robot operation and fast movement interrupts. • A probe alignment unit which improves the (absolute) accuracy of the probe positioning. • A computer operating Windows 2000 or Windows XP. • DASY4 software. • Remote controls with teach pendant and additional circuitry for robot safety such as warning lamps, etc. • The SAM twin phantom enabling testing left-hand and right-hand usage. • The device holder for handheld mobile phones. • Tissue simulating liquid mixed according to the given recipes. • Validation dipole kits allowing to validate the proper functioning of the system. COMPLIANCE CERTIFICATION SERVICES Page: 7 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 3.1 COMPOSITION OF INGREDIENTS FOR TISSUE SIMULATING LIQUIDS The following tissue formulations are provided for reference only as some of the parameters have not been thoroughly verified. The composition of ingredients may be modified accordingly to achieve the desired target tissue parameters required for routine SAR evaluation. Ingredients Frequency (MHz) (% by weight) 450 835 915 1900 2450 Tissue Type Head Body Head Body Head Body Head Body Head Body Water 38.56 51.16 41.45 52.4 41.05 56.0 54.9 40.4 62.7 73.2 Salt (NaCl) 3.95 1.49 1.45 1.4 1.35 0.76 0.18 0.5 0.5 0.04 Sugar 56.32 46.78 56.0 45.0 56.5 41.76 0.0 58.0 0.0 0.0 HEC 0.98 0.52 1.0 1.0 1.0 1.21 0.0 1.0 0.0 0.0 Bactericide 0.19 0.05 0.1 0.1 0.1 0.27 0.0 0.1 0.0 0.0 Triton X-100 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 36.8 0.0 DGBE 0.0 0.0 0.0 0.0 0.0 0.0 44.92 0.0 0.0 26.7 Dielectric Constant 43.42 58.0 42.54 56.1 42.0 56.8 39.9 54.0 39.8 52.5 Conductivity (S/m) 0.85 0.83 0.91 0.95 1.0 1.07 1.42 1.45 1.88 1.78 Salt: 99+% Pure Sodium Chloride Sugar: 98+% Pure Sucrose Water: De-ionized, 16 MΩ+ resistivity HEC: Hydroxyethyl Cellulose DGBE: 99+% Di(ethylene glycol) butyl ether, [2-(2-butoxyethoxy)ethanol] Triton X-100 (ultra pure): Polyethylene glycol mono [4-(1,1, 3, 3-tetramethylbutyl)phenyl]ether COMPLIANCE CERTIFICATION SERVICES Page: 8 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 4 SIMULATING LIQUID PARAMETERS CHECK The simulating liquids should be checked at the beginning of a series of SAR measurements to determine of the dielectric parameters are within the tolerances of the specified target values. The relative permittivity and conductivity of the tissue material should be within ± 5% of the values given in the table below. Dielectric Probe Network Analyzer Personal Computer Set-up for liquid parameters check Reference Values of Tissue Dielectric Parameters for Head and Body Phantom (for 150 – 3000 MHz and 5800 MHz) The head tissue dielectric parameters recommended by the IEEE SCC-34/SC-2 in IEEE Standard 1528 have been incorporated in the following table. These head parameters are derived from planar layer models simulating the highest expected SAR for the dielectric properties and tissue thickness variations in a human head. Other head and body tissue parameters that have not been specified in P1528 are derived from the tissue dielectric parameters computed from the 4-Cole-Cole equations and extrapolated according to the head parameters specified in IEEE Standard 1528. Head Body Target Frequency (MHz) εr σ (S/m) εr σ (S/m) 150 52.3 0.76 61.9 0.80 300 45.3 0.87 58.2 0.92 450 43.5 0.87 56.7 0.94 835 41.5 0.90 55.2 0.97 900 41.5 0.97 55.0 1.05 915 41.5 0.98 55.0 1.06 1450 40.5 1.20 54.0 1.30 1610 40.3 1.29 53.8 1.40 1800 – 2000 40.0 1.40 53.3 1.52 2450 39.2 1.80 52.7 1.95 3000 38.5 2.40 52.0 2.73 5800 35.3 5.27 48.2 6.00 (εr = relative permittivity, σ = conductivity and ρ = 1000 kg/m3) COMPLIANCE CERTIFICATION SERVICES Page: 9 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 4.1 SIMULATING LIQUID PARAMETER CHECK RESULT Simulating Liquid Dielectric Parameters Check Result @ Muscle 835 MHz Room Ambient Temperature = 22°C; Relative humidity = 40% Measured by: Ninous Davoudi Simulating Liquid Target Parameters Measured Deviation (%) Limit (%) f (MHz) Temp. (°C) Depth (cm) e' 55.3136 Relative Permittivity (єr): 55.3136 55.2 0.21 ±5 835 21 15 e" 21.4024 Conductivity (σ): 0.99419 0.97 2.49 ±5 Liquid Check Ambient temperature: 22.0 deg. C; Liquid temperature: 21.0 deg C June 21, 2007 05:04 PM Frequency e' e'' 800000000. 55.2550 21.3126 805000000. 55.3172 21.3286 810000000. 55.4131 21.3426 815000000. 55.4450 21.3508 820000000. 55.4764 21.3866 825000000. 55.4377 21.3972 830000000. 55.4019 21.4122 835000000. 55.3136 21.4024 840000000. 55.2328 21.3790 845000000. 55.1098 21.3282 850000000. 54.9945 21.2644 855000000. 54.8690 21.2275 860000000. 54.7685 21.1385 865000000. 54.6143 21.1037 870000000. 54.4945 21.0138 875000000. 54.4055 20.9453 880000000. 54.3413 20.9108 885000000. 54.2910 20.8819 890000000. 54.2997 20.8934 895000000. 54.3417 20.8809 900000000. 54.3494 20.9393 The conductivity (σ) can be given as: σ = ωε0 e''= 2 π f ε0 e'' where f = target f * 106 ε0 = 8.854 * 10-12 COMPLIANCE CERTIFICATION SERVICES Page: 10 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE Simulating Liquid Dielectric Parameters Check Result @ Muscle 900 MHz Room Ambient Temperature = 22°C; Relative humidity = 40% Measured by: Ninous Davoudi Simulating Liquid Target Parameters Measured Deviation (%) Limit (%) f (MHz) Temp. (°C) Depth (cm) e' 54.3494 Relative Permittivity (єr): 54.3494 55.0 -1.18 ±5 900 21 15 e" 20.9393 Conductivity (σ): 1.04839 1.05 -0.15 ±5 Liquid Check Ambient temperature: 22.0 deg. C; Liquid temperature: 21.0 deg C June 21, 2007 05:04 PM Frequency e' e'' 850000000. 54.9945 21.2644 855000000. 54.8690 21.2275 860000000. 54.7685 21.1385 865000000. 54.6143 21.1037 870000000. 54.4945 21.0138 875000000. 54.4055 20.9453 880000000. 54.3413 20.9108 885000000. 54.2910 20.8819 890000000. 54.2997 20.8934 895000000. 54.3417 20.8809 900000000. 54.3494 20.9393 905000000. 54.3442 21.0282 910000000. 54.3139 21.0899 915000000. 54.2622 21.1339 920000000. 54.1839 21.1470 925000000. 54.0997 21.1422 930000000. 54.0571 21.1105 935000000. 53.9922 21.0474 940000000. 53.9574 20.9318 945000000. 53.9776 20.8755 950000000. 53.9663 20.7919 The conductivity (σ) can be given as: σ = ωε0 e''= 2 π f ε0 e'' where f = target f * 106 ε0 = 8.854 * 10-12 COMPLIANCE CERTIFICATION SERVICES Page: 11 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE Simulating Liquid Dielectric Parameters Check Result @ Muscle 1900 MHz Room Ambient Temperature = 22°C; Relative humidity = 40% Measured by: Ninous Davoudi Simulating Liquid Target Parameters Measured Deviation (%) Limit (%) f (MHz) Temp. (°C) Depth (cm) e' 53.7197 Relative Permittivity (єr): 53.7197 53.3 0.79 ±5 1900 21 15 e" 13.8737 Conductivity (σ): 1.46644 1.52 -3.52 ±5 Liquid Check Ambient temperature: 22.0 deg. C; Liquid temperature: 21.0 deg C June 21, 2007 09:31 PM Frequency e' e'' 1710000000. 53.8263 13.5427 1720000000. 53.8735 13.6551 1730000000. 53.9369 13.7568 1740000000. 54.0297 13.7808 1750000000. 54.1042 13.6860 1760000000. 54.1659 13.5420 1770000000. 54.2101 13.4713 1780000000. 54.1210 13.4620 1790000000. 53.9680 13.4950 1800000000. 53.7937 13.5591 1810000000. 53.6549 13.6849 1820000000. 53.5282 13.8703 1830000000. 53.4333 14.0465 1840000000. 53.4011 14.1052 1850000000. 53.5181 14.0589 1860000000. 53.7537 13.9685 1870000000. 53.9508 13.9467 1880000000. 54.0063 13.9254 1890000000. 53.8783 13.8992 1900000000. 53.7197 13.8737 1910000000. 53.5079 13.8712 The conductivity (σ) can be given as: σ = ωε0 e''= 2 π f ε0 e'' where f = target f * 106 ε0 = 8.854 * 10-12 COMPLIANCE CERTIFICATION SERVICES Page: 12 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 5 SYSTEM PERFORMANCE CHECK The system performance check is performed prior to any usage of the system in order to guarantee reproducible results. The system performance check verifies that the system operates within its specifications of ±10%. System Performance Check Measurement Conditions • The measurements were performed in the flat section of the SAM twin phantom filled with Body simulating liquid of the following parameters. • The DASY4 system with an Isotropic E-Field Probe EX3DV3-SN: 3531 was used for the measurements. • The dipole was mounted on the small tripod so that the dipole feed point was positioned below the center marking of the flat phantom section and the dipole was oriented parallel to the body axis (the long side of the phantom). The standard measuring distance was 10 mm (above 1 GHz) and 15 mm (below 1 GHz) from dipole center to the simulating liquid surface. • The coarse grid with a grid spacing of 15 mm was aligned with the dipole. For 5 GHz band - The coarse grid with a grid spacing of 10 mm was aligned with the dipole. • Special 5 x 5 x 7 fine cube was chosen for cube integration(dx=dy=7.5mm; dz=5mm). For 5 GHz band - Special 8x8x8 fine cube was chosen for cube integration(dx=dy=4.3mm; dz=3mm) • Distance between probe sensors and phantom surface was set to 4 mm. For 5 GHz band - Distance between probe sensors and phantom surface was set to 2.0mm • The dipole input power (forward power) was 250 mW±3%. • The results are normalized to 1 W input power. Reference SAR Values for body-tissue In the table below, the numerical reference SAR values of a SPEAG validation dipoles placed below the flat phantom filled with body-tissue simulating liquid are given. The reference SAR values were calculated using the finite-difference time-domain method and the geometry parameters. Distance Frequency SAR (1g) SAR (10g) SAR (peak) Dipole Type (mm) (MHz) [W/kg] [W/kg] [W/kg] D450V2 15 450 5.01 3.36 7.22 D835V2 15 835 9.71 6.38 14.1 D900V2 15 900 11.1 7.17 16.3 D1450V2 10 1450 29.6 16.6 49.8 D1800V2 10 1800 38.5 20.3 67.5 D1900V2 10 1900 39.8 20.8 69.6 D2000V2 10 2000 40.9 21.2 71.5 D2450V2 10 2450 51.2 23.7 97.6 Note: All SAR values normalized to 1 W forward power. COMPLIANCE CERTIFICATION SERVICES Page: 13 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 5.1 SYSTEM PERFORMANCE CHECK RESULTS System Validation Dipole: D900V2 SN: 108 Date: June 21, 2007 Room Ambient Temperature = 22°C; Relative humidity = 40% Measured by: Ninous Davoudi Body Sim ulating Liquid Norm alized Deviation Lim it SAR (m W /g) Target to 1 W (% ) (% ) f (MHz) Tem p. (°C) Depth (cm ) 1g 2.78 11.12 11.1 0.18 ± 10 900 21 15 10g 1.81 7.24 7.17 0.98 ± 10 System Validation Dipole: D1900V2 SN:5d043 Date: June 21, 2007 Room Ambient Temperature = 22°C; Relative humidity = 40% Measured by: Ninous Davoudi Body Sim ulating Liquid Norm alized Deviation Lim it SAR (m W /g) Target to 1 W (% ) (% ) f (MHz) Tem p. (°C) Depth (cm ) 1g 10.30 41.2 39.8 3.52 ± 10 1900 21 15 10g 5.4 21.6 20.8 3.85 ± 10 COMPLIANCE CERTIFICATION SERVICES Page: 14 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 6 SAR MEASURMENT PROCEDURE A summary of the procedure follows: a) A measurement of the SAR value at a fixed location is used as a reference value for assessing the power drop of the DUT. The SAR at this point is measured at the start of the test, and then again at the end of the test. b) The SAR distribution at the exposed flat section of the flat phantom is measured at a distance of 4 mm from the inner surface of the shell. The area covers the entire dimension of the DUT and the horizontal grid spacing is 15 mm x 15 mm. Based on this data, the area of the maximum absorption is determined by Spline interpolation. The first Area Scan covers the entire dimension of the DUT to ensure that the hotspot was correctly identified. For 5 GHz band - The SAR distribution at the exposed flat section of the flat phantom is measured at a distance of 2.0 mm from the inner surface of the shell. The area covers the entire dimension of the DUT and the horizontal grid spacing is 10 mm x 10 mm. Based on this data, the area of the maximum absorption is determined by Spline interpolation. The first Area Scan covers the entire dimension of the DUT to ensure that the hotspot was correctly identified. c) Around this point, a volume of X=Y= 30 and Z=21 mm is assessed by measuring 5 x 5 x 7 mm points. On the basis of this data set, the spatial peak SAR value is evaluated with the following procedure: For 5 GHz band - Around this point, a volume of X=Y=24 and Z=20 mm is assessed by measuring 7 x 7 x 9 mm points. On the basis of this data set, the spatial peak SAR value is evaluated with the following procedure: (i) The data at the surface are extrapolated, since the centre of the dipoles is 1.2 mm away from the tip of the probe and the distance between the surface and the lowest measuring point is 1.3 mm. The extrapolation is based on a least square algorithm. A polynomial of the fourth order is calculated through the points in z-axes. This polynomial is then used to evaluate the points between the surface and the probe tip. (ii) The maximum interpolated value is searched with a straightforward algorithm. Around this maximum the SAR values averaged over the spatial volumes (1 g and 10 g) are computed using the 3D-Spline interpolation algorithm. The 3D-Spline is composed of three one- dimensional splines with the “Not a knot”- condition (in x, y and z-direction). The volume is integrated with the trapezoidal – algorithm. One thousand points (10 x 10 x 10) are interpolated to calculate the averages. (iii) All neighbouring volumes are evaluated until no neighbouring volume with a higher average value is found. (iv) The SAR value at the same location as in Step (a) is again measured to evaluate the actual power drift. COMPLIANCE CERTIFICATION SERVICES Page: 15 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 6.1 DASY4 SAR MEASURMENT PROCEDURE Step 1: Power Reference Measurement The Power Reference Measurement and Power Drift Measurements are for monitoring the power drift of the device under test in the batch process. The Minimum distance of probe sensors to surface determines the closest measurement point to phantom surface. The minimum distance of probe sensors to surface is 2.1 mm. This distance cannot be smaller than the Distance of sensor calibration points to probe tip as defined in the probe properties (for example, 1.2 mm for an EX3DV3 probe type). Step 2: Area Scan The Area Scan is used as a fast scan in two dimensions to find the area of high field values, before doing a fine measurement around the hot spot. The sophisticated interpolation routines implemented in DASY4 software can find the maximum locations even in relatively coarse grids. When an Area Scan has measured all reachable points, it computes the field maximal found in the scanned area, within a range of the global maximum. The range (in dB) is specified in the standards for compliance testing. For example, a 2 dB range is required in IEEE Standard 1528, EN 50361 and IEC 62209 standards, whereby 3 dB is a requirement when compliance is assessed in accordance with the ARIB standard (Japan). If only one Zoom Scan follows the Area Scan, then only the absolute maximum will be taken as reference. For cases where multiple maximums are detected, the number of Zoom Scans has to be increased accordingly. Step 3: Zoom Scan Zoom Scans are used to assess the peak spatial SAR values within a cubic averaging volume containing 1 g and 10 g of simulated tissue. The Zoom Scan measures 5 x 5 x 7 points within a cube whose base faces are centered on the maxima found in a preceding area scan job within the same procedure. When the measurement is done, the Zoom Scan evaluates the averaged SAR for 1 g and 10 g and displays these values next to the job’s label. For 5 GHz band – Same as above except the Zoom Scan measures 7 x 7 x 9 points. Step 4: Power drift measurement The Power Drift Measurement measures the field at the same location as the most recent power reference measurement within the same procedure, and with the same settings. The Power Drift Measurement gives the field difference in dB from the reading conducted within the last Power Reference Measurement. This allows a user to monitor the power drift of the device under test within a batch process. The measurement procedure is the same as Step 1. Step 5: Z-Scan The Z Scan measures points along a vertical straight line. The line runs along the Z-axis of a one- dimensional grid. In order to get a reasonable extrapolation, the extrapolated distance should not be larger than the step size in Z-direction. COMPLIANCE CERTIFICATION SERVICES Page: 16 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 7 PROCEDURE USED TO ESTABLISH TEST SIGNAL The following procedures had been used to prepare the EUT for the SAR test. The following setting is used to prepare the EUT in GSM850/1900MHz bands for the SAR test. Agilent 8960 series 10 E5515C, Wireless Communication Test Set is used to control the EUT and measure the output power. The following setting was used to establish the signal. Service selection Î Test Mode A – Auto Slot Config. Î off Main Service Î Packet Data Network Support Î GSM only Slot Config Î 33 dBm for GSM850 and 30 dBm for GSM1900 Conducted power: GSM850 Channel Frequency Power (MHz) (dBm) 128 824.2 33.20 192 837 33.10 251 848.8 33.00 GSM1900 Channel Frequency Power (MHz) (dBm) 512 1850.2 29.40 661 1880.0 29.60 810 1909.8 29.80 COMPLIANCE CERTIFICATION SERVICES Page: 17 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 8 SAR MEASURMENT RESULTS 8.1 CELL BAND 8.1.1 POSITION 1 & 2 15mm 15mm Position 1 Position 2 GSM 850 Test Mode Channel f (MHz) Measured SAR Power Drift Extrapolated1) SAR 1g (mW/g) (dB) 1g (mW/g) 128 824.2 Position 1 192 837.0 0.638 0.000 0.638 251 848.8 251 4) 848.8 0.645 0.000 0.645 128 824.2 Position 2 192 837.0 0.349 0.000 0.349 251 848.8 Notes: 1) The exact method of extrapolation is Measured SAR x 10^(-drift/10). The SAR reported at the end of the measurement process by the DASY4 system can be scaled up by the Power drift to determine the SAR at the beginning of the measurement process. 2) The SAR measured at the middle channel for this configuration is at least 3 dB lower (0.8 mW/g) than SAR limit (1.6 mW/g), thus testing at low & high channel is optional. 3) Please see attachments for the detailed measurement data and plots showing the maximum SAR location of the EUT. 4) With alternate battery. COMPLIANCE CERTIFICATION SERVICES Page: 18 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 8.1.2 POSITION 3 & 4 15mm 15mm Position 3 Position 4 GSM 850 Test Mode Channel f (MHz) Measured SAR Power Drift Extrapolated1) SAR 1g (mW/g) (dB) 1g (mW/g) 128 824.2 Position 3 192 837.0 0.272 0.000 0.272 251 848.8 128 824.2 Position 4 192 837.0 0.309 0.000 0.309 251 848.8 Notes: 1) The exact method of extrapolation is Measured SAR x 10^(-drift/10). The SAR reported at the end of the measurement process by the DASY4 system can be scaled up by the Power drift to determine the SAR at the beginning of the measurement process. 2) The SAR measured at the middle channel for this configuration is at least 3 dB lower (0.8 mW/g) than SAR limit (1.6 mW/g), thus testing at low & high channel is optional. 3) Please see attachments for the detailed measurement data and plots showing the maximum SAR location of the EUT. COMPLIANCE CERTIFICATION SERVICES Page: 19 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 8.1.3 POSITION 5 & 6 Position 5 Position 6 GSM 850 Test Mode Channel f (MHz) Measured SAR Power Drift Extrapolated1) SAR 1g (mW/g) (dB) 1g (mW/g) 128 824.2 Position 5 192 837.0 0.016 -0.055 0.017 251 848.8 128 824.2 Position 6 192 837.0 0.023 -0.029 0.023 251 848.8 Notes: 1) The exact method of extrapolation is Measured SAR x 10^(-drift/10). The SAR reported at the end of the measurement process by the DASY4 system can be scaled up by the Power drift to determine the SAR at the beginning of the measurement process. 2) The SAR measured at the middle channel for this configuration is at least 3 dB lower (0.8 mW/g) than SAR limit (1.6 mW/g), thus testing at low & high channel is optional. 3) Please see attachments for the detailed measurement data and plots showing the maximum SAR location of the EUT. 4) The separation distance is 15mm. COMPLIANCE CERTIFICATION SERVICES Page: 20 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 8.2 PCS BAND 8.2.1 POSITION 1 & 2 15mm 15mm Position 1 Position 2 GSM 1900 Test Mode Channel f (MHz) Measured SAR Power Drift Extrapolated1) SAR 1g (mW/g) (dB) 1g (mW/g) 512 1850.2 Position 1 661 1880.0 0.351 -0.050 0.355 810 1909.8 6614) 1880.0 0.370 -0.057 0.375 512 1850.2 Position 2 661 1880.0 0.082 -0.080 0.084 810 1909.8 Notes: 1) The exact method of extrapolation is Measured SAR x 10^(-drift/10). The SAR reported at the end of the measurement process by the DASY4 system can be scaled up by the Power drift to determine the SAR at the beginning of the measurement process. 2) The SAR measured at the middle channel for this configuration is at least 3 dB lower (0.8 mW/g) than SAR limit (1.6 mW/g), thus testing at low & high channel is optional. 3) Please see attachments for the detailed measurement data and plots showing the maximum SAR location of the EUT. 4) With alternate battery. COMPLIANCE CERTIFICATION SERVICES Page: 21 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 8.2.2 POSITION 3 & 4 15mm 15mm Position 3 Position 4 GSM 1900 Test Mode Channel f (MHz) Measured SAR Power Drift Extrapolated1) SAR 1g (mW/g) (dB) 1g (mW/g) 512 1850.2 Position 3 661 1880.0 0.097 0.000 0.097 810 1909.8 Notes: 1) The exact method of extrapolation is Measured SAR x 10^(-drift/10). The SAR reported at the end of the measurement process by the DASY4 system can be scaled up by the Power drift to determine the SAR at the beginning of the measurement process. 2) The SAR measured at the middle channel for this configuration is at least 3 dB lower (0.8 mW/g) than SAR limit (1.6 mW/g), thus testing at low & high channel is optional. 3) Please see attachments for the detailed measurement data and plots showing the maximum SAR location of the EUT. 4) Position 4 skipped since SAR value is low. COMPLIANCE CERTIFICATION SERVICES Page: 22 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 8.2.3 POSITION 5 & 6 Position 5 Position 6 GSM 1900 Test Mode Channel f (MHz) Measured SAR Power Drift Extrapolated1) SAR 1g (mW/g) (dB) 1g (mW/g) 512 1850.2 Position 5 661 1880.0 0.226 0.000 0.226 810 1909.8 512 1850.2 Position 6 661 1880.0 0.017 0.000 0.017 810 1909.8 Notes: 1) The exact method of extrapolation is Measured SAR x 10^(-drift/10). The SAR reported at the end of the measurement process by the DASY4 system can be scaled up by the Power drift to determine the SAR at the beginning of the measurement process. 2) The SAR measured at the middle channel for this configuration is at least 3 dB lower (0.8 mW/g) than SAR limit (1.6 mW/g), thus testing at low & high channel is optional. 3) Please see attachments for the detailed measurement data and plots showing the maximum SAR location of the EUT. 4) The separation distance is 15mm. COMPLIANCE CERTIFICATION SERVICES Page: 23 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 9 MEASURMENT UNCERTAINTY 9.1 MEASURMENT UNCERTAINTY FOR 300 MHz – 3000 MHz Probe Std. Unc.(±%) Uncertainty component Tol. (±%) Div. Ci (1g) Ci (10g) Dist. Ui (1g) Ui(10g) Measurement System Probe Calibration 4.80 N 1 1 1 4.80 4.80 Axial Isotropy 4.70 R 1.732 0.707 0.707 1.92 1.92 Hemispherical Isotropy 9.60 R 1.732 0.707 0.707 3.92 3.92 Boundary Effects 1.00 R 1.732 1 1 0.58 0.58 Linearity 4.70 R 1.732 1 1 2.71 2.71 System Detection Limits 1.00 R 1.732 1 1 0.58 0.58 Readout Electronics 1.00 N 1 1 1 1.00 1.00 Response Time 0.80 R 1.732 1 1 0.46 0.46 Integration Time 2.60 R 1.732 1 1 1.50 1.50 RF Ambient Conditions - Noise 1.59 R 1.732 1 1 0.92 0.92 RF Ambient Conditions - Reflections 0.00 R 1.732 1 1 0.00 0.00 Probe Positioner Mechnical Tolerance 0.40 R 1.732 1 1 0.23 0.23 Probe Positioning With Respect to Phantom Shell 2.90 R 1.732 1 1 1.67 1.67 Extrapolation, interpolation, and integration algorithms for max. SAR evaluation 3.90 R 1.732 1 1 2.25 2.25 Test sample Related Test Sample Positioning 1.10 N 1 1 1 1.10 1.10 Device Holder Uncertainty 3.60 N 1 1 1 3.60 3.60 Power and SAR Drift Measurement 5.00 R 1.732 1 1 2.89 2.89 Phantom and Tissue Parameters Phantom Uncertainty 4.00 R 1.732 1 1 2.31 2.31 Liquid Conductivity - Target 5.00 R 1.732 0.64 0.43 1.85 1.24 Liquid Conductivity - Meas. 8.60 N 1 0.64 0.43 5.50 3.70 Liquid Permittivity - Target 5.00 R 1.732 0.6 0.49 1.73 1.41 Liquid Permittivity - Meas. 3.30 N 1 0.6 0.49 1.98 1.62 Combined Standard Uncertainty RSS 11.44 10.49 Expanded Uncertainty (95% Confidence Interval) K=2 22.87 20.98 Notesfor table 1. Tol. - tolerance in influence quaitity 2. N - Nomal 3. R - Rectangular 4. Div. - Divisor used to obtain standard uncertainty 5. Ci - is te sensitivity coefficient COMPLIANCE CERTIFICATION SERVICES Page: 24 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 10 EQUIPMENT LIST AND CALIBRATION Cal. Due date Name of Equipment Manufacturer Type/Model Serial Number MM DD Year Robot - Six Axes Stäubli RX90BL N/A N/A Robot Remote Control Stäubli CS7MB 3403-91535 N/A DASY4 Measurement Server SPEAG SEUMS001BA 1041 N/A Probe Alignment Unit SPEAG LB (V2) 261 N/A SAM Phantom (SAM1) SPEAG QD000P40CA 1185 N/A SAM Phantom (SAM2) SPEAG QD000P40CA 1050 N/A Oval Flat Phantom (ELI 4.0) SPEAG QD OVA001 B 1003 N/A Electronic Probe kit HP 85070C N/A N/A S-Parameter Network Analyzer Agilent 8753ES-6 US39173569 2 14 2008 E-Field Probe SPEAG EX3DV4 3554 4 24 2008 Thermometer ERTCO 639-1S 1718 11 7 2007 Data Acquisition Electronics SPEAG DAE3 V1 427 11 16 2007 System Validation Dipole SPEAG D900V2 108 2 22 2008 System Validation Dipole SPEAG D1900V2 5d043 1 23 2008 Signal Generator R&S SMP 04 DE34210 10 9 2007 Power Meter Giga-tronics 8651A 8651404 4 3 2008 Power Sensor Giga-tronics 80701A 1834588 4 17 2008 Amplifier Mini-Circuits ZHL-42W D072701-5 N/A Radio Communication Tester R &S CMU 200 106291 4 16 2008 Simulating Liquid CCS M835 N/A Within 24 hrs of first test Simulating Liquid CCS M1900 N/A Within 24 hrs of first test COMPLIANCE CERTIFICATION SERVICES Page: 25 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 11 PHOTOS DUT COMPLIANCE CERTIFICATION SERVICES Page: 26 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE Antenna Location Antenna DUT with Battery Compartment COMPLIANCE CERTIFICATION SERVICES Page: 27 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE Battery – Lexel LH070-3A44C3BROT COMPLIANCE CERTIFICATION SERVICES Page: 28 of 29 This report shall not be reproduced except in full, without the written approval of CCS.

REPORT NO: 07U11144-1 DATE: June 29, 2007 FCC ID: JUPTRIMTRACE 12 ATTACHMENTS No. Contents No. Of Pages 1 System Performance Check Plots 4 2-1 SAR Test Plots – Cell Band 8 2-2 SAR Test Plots – PCS Band 7 3 Certificate of E-Field Probe - EX3DV4SN3554 10 4 Certificate of System Validation Dipole - D900V2 SN:108 9 5 Certificate of System Validation Dipole - D1900V2 SN:5d043 9 END OF REPORT COMPLIANCE CERTIFICATION SERVICES Page: 29 of 29 This report shall not be reproduced except in full, without the written approval of CCS.


Document Created: 2007-06-29 14:09:05
Document Modified: 2007-06-29 14:09:05
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC