revised installation instructed with corrected RF exposure statement

FCC ID: JQU-801154

Users Manual

Download: PDF
FCCID_288040

CR2000 Reader Installation Instructions                                                                                      Document A316000-775

CR2000 - Reader Kit                                                                        CR2000- Installation Items
                                                                                           The kit of reader components described at left does not
                                                                                           include the following required items…
                                                   antenna                                  1 PC cable, RS232 (DTE-DCE), 12 feet (see Fig 1)
                                                                                            A/R antenna mount hardware: bracket(s), clamp(s), mast, etc.
                                                                                            100 feet (or less A/R) of RG213U cable
                                                                                            2.5 feet of RG58U cable
                                                                                            1 N-male connector for RG213U cable
                                                                                            1 N-female connector for RG213U cable
                                          CR2000 reader                                     1 N-male connector for RG58U cable
                                                                                            1 N-female connector for RG58U cable
           power                                                                            1 each of fixed attenuators: 1, 2, 3, 4, 5, 6, and 7 dB
            pack                                                                            A/R heat shrink tubing, electrical tape, cable ties and clamps

                                                                                           NOTE: During system installation, the contractor determines
                                                software diskette                          the fixed RF attenuation level required.

                                                                                           CR2000- Installation Overview
                                                                                           ♦    The antenna is installed within the distance/angular limits
                                                                                                of the "pick-up point" as indicated in Table 1 on the back
                                                                                                page
                                                                                           ♦    The reader, power pack, antenna adapter cable and "total
                                                                                                RF attenuation" components are installed at a location
                                                                                                inside the building (see Figure 1 on the back page) that is
CR2000 - Reader Kit Packing List                                                                (all of)…
 Part Number            Description                                                                  ƒ within 6 feet of a 110Vac power main drop
 801075-001             CR2000 Compact Reader                                                        ƒ within 12 feet (4 meters) of the host computer
 318993-009             DC Power Pack, 110Vac input, output 5V/3A,                                   ƒ within 100 feet of the antenna mounting location
                        15V/1.5A, -15V/0.3A, Skynet #SNP-PA54                                            outside the building
 318145-177             CR2000 PC Software on Diskette                                     ♦    All system connections are completed as indicated in the
 801076-001             Antenna Assembly                                                        CR2000 - Installation Steps listed on the back page.
                                                                                           ♦    The CR2000 PC application software is transferred from
CR2000 Reader - Connections                                                                     the diskette to the host computer and is running.
                                                                                           ♦    The total RF attenuation value is determined by varying
                                                                                                the configuration of the available fixed attenuators.
                                             antenna
         power                 PC            adapter
         cable                cable                                                        NOTE: Where necessary, Mark IV Industries Ltd. I.V.H.S.
                                              cable
                                                                                           personnel may be required to "fine tune" the system RF
                                                                                           attenuation parameters.

                                                                                           Document Revision Record
                                                                                            Rev Date          ECN                                           Approved
                                                                                            A    18-Jan-01    Preliminary


CR2000 - Installation Tools
Your tool kit should include (but is not limited to)…
♦ N-type connector crimp tool
♦ screwdrivers: flat blade, Philips blade
♦ SAE Socket set
♦ utility knife, wire cutter, wire stripper




2001 MARK IV INDUSTRIES LTD. Revision B, Issue printed on 12/6/2002 1:46 PM,                                                          filename: E:\Ready_To_Convert\Doc\288040.DOC
CONFIDENTIAL: This document is the confidential property of Mark IV Industries Ltd. and may not be released or copied without written permission.


CR2000 Reader Installation Instructions                                                                               Document A316000-775
                                                                                                    CR2000 - Installation Steps
CR2000 - Antenna mounting                                                                           Connect the antenna with the reader via RF feedline and RF
The antenna will be mounted over-head at a height of Ha ft                                          attenuator(s) and antenna adapter cable.
with horizontal polarization where Ha is measured from the
                                                                                                    1) Disconnect the power main input to the power supply.
highest part of the antenna. Determine the distance Do (in ft)
                                                                                                    2) Connect the Power supply output to the CR2000 reader.
between the "pick-up point" and the antenna mast, and use it
                                                                                                    3) Connect the PC port COM1 to the reader host port using
to determine the antenna tilt down angle α° in the in-lane                                              the provided straight through RS-232 cable.
direction (H Plane), using the following table.                                                     4) Connect the RF cable adapter (RG58 short cable) to the
     Antenna        Pick-up Point     Antenna Tilt       Beam                                           reader RF port (Type N connector).
   Height (Ha)          (Do) *         Angle (α)       Center **                                    5) Connect the RF feedline to the RF cable adapter via the
       [ft]               [ft]           [Deg]             [ft]                                         fixed attenuator(s) referenced in step 9. Install a Type-N
  12               5 to 7            15               3                                                 Male connector at the end of the feedline.
                   7 to 9            18               4                                             6) Route the RF feedline through the wall. At the feedline
  12.5             5 to 7            15               3                                                 antenna end, slip 6" of heatshrink tubing on the cable.
                   7 to 9            18               4                                                 Install a Type-N female connector at the end of the
  13               6 to 8            15               3.5                                               feedline. Make the connection with the antenna.
                   8 to 10           18               4.5                                           7) Reconnect the power main input to the power supply.
  13.5             7 to 9            15               4                                             8) Execute the CR2000 PC application software as
                   9 to 10           18               4.5                                               referenced in document A316000-743.
* Distance referred to the antenna mast.                                                            9) Determine the "total RF attenuation" value by varying the
** Based on semi-empirical data.                                                                        configuration of the available fixed attenuator value(s).
                                                                                                    10) After the system has been fully tested OK then heat shrink
Note: User must maintain a separation distance of 23cm from                                             the tubing (in step 6) over the antenna connector to make
the antenna. The antenna has gain of 6 db.                                                              it water tight.



                     Figure 1 - Installation Diagram                                                                   vehicle with a
                                                                                                                        transponder




                                                                                                                                        antenna
                                                                                               "RF capture zone"
                                                                                              when RF is turned on
                                                                                                                                N male
                         ***total RF attenuation" value
                            is determined at the end of                                                                         N female
                                                                                                       outside the building
                            the installation process
                                                                                                        inside the building    RF cable
                                         "total RF attenuation" value                                                          RG213U
                              N male                                                                          N male           < 100 ft
                                           attenuator ***               attenuator         attenuator
                                                                                                                antenna feedline cable
                                          N female/female           N male/female       N male/female
                                                                                                                                  110 Vac
                                                                                                                       DC
                                                                                                                                   mains
                     RF cable                                                                                        power
                                                                                       CR2000                         pack
                                                                                                                                   supply
                     RG58U                                            N male           Reader
                     < 2.5 ft            antenna adapter cable                                      DCE DB9 female Host port (P2)
                                                                                N female

                                                                                                       DB9 male
                                                           DB9 male*
                                                                                   PC cable           RS232 cable
                                     Host PC             DTE
                                                                    DB9 female*                       #22AWG, 3 conductor
                                     running                                                          > 6 ft < 40 ft (12 ft default or specify)
                                    CR2000-PC                      *Please verify the serial port
                                                                                                      Optional: RS485 cable
                                     software                      connector type on your host
                                                                   PC, is it DB9 or DB25?             #22AWG, 5 conductor
                                                                                                      > 40 ft < 200 ft (always specify)




2001 MARK IV INDUSTRIES LTD. Revision B, Issue printed on 12/6/2002 1:46 PM,                                                                 filename: E:\Ready_To_Convert\Doc\288040.DOC
CONFIDENTIAL: This document is the confidential property of Mark IV Industries Ltd. and may not be released or copied without written permission.



Document Created: 2002-12-06 13:46:57
Document Modified: 2002-12-06 13:46:57

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC