CKC test report

FCC ID: JQ6537Y

Test Report

Download: PDF
FCCID_62889

CERTIFICATION TEST REPORT FOR THE RFID PROXIMITY READER, 5375A MAXIPROX (5375-310-01) FCC PART 15 SUBPART C & CANADIAN DEPARTMENT OF INDUSTRY RSS-210 COMPLIANCE DATE OF ISSUE: SEPTEMBER 14, 1999 PREPARED FOR: PREPARED BY: HID Corporation Joyce Walker 9292 Jeronimo Road CKC Laboratories, Inc. Irvine, CA 92618-1905 5473A Clouds Rest Mariposa, CA 95338 P.O. No: 008008 W.O. No: 72268 Date of test: August 30 & September 2, 1999 Report No: FC99-030 DOCUMENTATION CONTROL: APPROVED BY: _____________________________ _____________________________ Tracy Phillips Dennis Ward Documentation Control Supervisor Director of Laboratories CKC Laboratories, Inc. CKC Laboratories, Inc. This report contains a total of 34 pages and may be reproduced in full only. Partial reproduction may only be done with the written consent of CKC Laboratories, Inc. Page 1 of 34 Report No: FC99-030

TABLE OF CONTENTS Administrative Information .............................................................................................3 Summary Of Results........................................................................................................4 Equipment Under Test (EUT) Description......................................................................4 Measurement Uncertainty................................................................................................4 EUT Operating Frequency...............................................................................................4 Peripheral Devices...........................................................................................................4 Report Of Measurements.................................................................................................5 Table 1: Highest Radiated Emission Levels - 9 kHz-30 MHz ...........................5 Table 2: Six Highest Radiated Emission Levels - 30 MHz-1000 MHz .............6 Table 3: Six Highest Conducted Emission Levels – 12 & 24 VDC...................7 Table A : List Of Test Equipment ...................................................................................8 EUT Setup .......................................................................................................................9 Test Instrumentation And Analyzer Settings...................................................................10 Table B : Analyzer Bandwidth Settings Per Frequency Range...........................10 Spectrum Analyzer Detector Functions...............................................................11 Peak .........................................................................................................11 Quasi-Peak...............................................................................................11 Average....................................................................................................11 Test Methods ...................................................................................................................12 Radiated Emissions Testing.................................................................................12 Conducted Emissions Testing .............................................................................13 Sample Calculations ........................................................................................................13 Appendix A : Information About The Equipment Under Test........................................14 I/O Ports...............................................................................................................15 Crystal Oscillators ...............................................................................................15 Printed Circuit Boards .........................................................................................15 Cable Information................................................................................................15 Required EUT Changes To Comply....................................................................15 Photograph Showing Radiated Emissions...........................................................16 Photograph Showing Radiated Emissions...........................................................17 Photograph Showing Conducted Emissions........................................................18 Appendix B : Measurement Data Sheets.........................................................................19 Page 2 of 34 Report No: FC99-030

CKC Laboratories, Inc. has Certificates of Accreditation from the following agencies: DATech (Germany); A2LA (USA); FCC (USA); VCCI (Japan); BSMI (Taiwan); HOKLAS (Hong Kong). CKC Laboratories, Inc. has Letters of Acceptance through an MRA for the following agencies: ACA/NATA (Australia); SABS (South Africa); SWEDAC (Sweden); TUV Rheinland-Germany; TUV Rheinland- Korea; TUV Rheinland-Russia; Radio Communications Agency (RA); NEMKO (Norway). ADMINISTRATIVE INFORMATION DATE OF TEST: August 30 & September 2, 1999 PURPOSE OF TEST: To demonstrate the compliance of the RFID Proximity Reader, 5375A MaxiProx (5375- 310-01), with the requirements for FCC Part 15 Subpart C & RSS-210 devices. MANUFACTURER: HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 REPRESENTATIVE: Ken Long TEST LOCATION: CKC Laboratories, Inc. 5473A Clouds Rest Mariposa, CA 95338 TEST PERSONNEL: Dustin Oaks TEST METHOD: ANSI C63.4 1992 FREQUENCY RANGE TESTED: 9kHz - 1000 MHz EQUIPMENT UNDER TEST: RFID Proximity Reader Manuf: HID Corporation Model: 5375A MaxiPro Final Assy: 5375-310-01 Serial: N/A FCC ID: JQ6537Y(pending) Page 3 of 34 Report No: FC99-030

SUMMARY OF RESULTS The HID Corporation RFID Proximity Reader, 5375A MaxiProx (5375-310-01), was tested in accordance with ANSI C63.4 1992 for compliance with FCC Part 15 Subpart C and RSS-210. As received, the above equipment was found to be fully compliant with the limits of FCC Part 15 Subpart C and RSS-210. The results in this report apply only to the items tested, as identified herein. EQUIPMENT UNDER TEST (EUT) DESCRIPTION RFID Proximity Reader MEASUREMENT UNCERTAINTY Associated with data in this report is a ±4dB measurement uncertainty. EUT OPERATING FREQUENCY The EUT was operating at 0.125 MHz. TEMPERATURE AND HUMIDITY DURING TESTING The temperature during testing was within +15°C and + 35°C. The relative humidity was between 20% and 75%. PERIPHERAL DEVICES The EUT was tested with the following peripheral device(s): DC Power Supply Manuf: Topward Electric Instruments Model: 2306 Serial: 920035 FCC ID: N/A Page 4 of 34 Report No: FC99-030

REPORT OF MEASUREMENTS The following tables report the highest worst case levels recorded during the tests performed on the RFID Proximity Reader, 5375A MaxiProx (5375-310-01). All readings taken are peak readings unless otherwise noted by a “Q” or “A”. The data sheets from which these tables were compiled are contained in Appendix B. Table 1: Highest Radiated Emission Levels – 9 kHz-30 MHz METER CORRECTION FACTORS CORRECTED SPEC FREQUENCY READING Mag Cable 15.31 Dist READING LIMIT MARGIN NOTES Loop MHz dBµV dB dB DB dB dBµV/m dBµV/m dB 0.125 48.5 12.2 0.1 -40.0 20.8 25.7 -4.9 NA-1 0.125 50.9 12.2 0.1 -40.0 23.2 25.7 -2.5 NA-2 Test Method: ANSI C63.4 1992 NOTES: H = Horizontal Polarization Spec Limit : FCC Part 15.209 V = Vertical Polarization Test Distance: 30 Meters N = No Polarization D = Dipole Reading Q = Quasi Peak Reading A = Average Reading 1 = 12VDC 2 = 24VDC COMMENTS: EUT operating on 12/24VDC via DC power supply. EUT is in continuos read mode with no card in the field. 40dB correction factor IAW FCC 15.31. Frequency Range scanned from 9kHz to 30MHz. Page 5 of 34 Report No: FC99-030

Table 2: Six Highest Radiated Emission Levels – 30 MHz-1000 MHz METER CORRECTION FACTORS CORRECTED SPEC FREQUENCY READING Ant Amp Cable Dist READING LIMIT MARGIN NOTES MHz dBµV dB dB dB dB dBµV/m dBµV/m dB 32.064 42.6 12.8 -27.0 1.0 29.4 40.0 -10.6 V-1 43.879 39.4 10.7 -27.0 1.2 24.3 40.0 -15.7 V-2 56.217 44.3 9.8 -26.8 1.3 28.6 40.0 -11.4 V-2 108.806 32.6 12.7 -26.8 1.9 20.4 43.5 -23.1 V-2 134.956 33.2 13.6 -26.8 2.1 22.1 43.5 -21.4 V-1 150.042 36.1 12.7 -26.8 2.2 24.2 43.5 -19.3 V-1 Test Method: ANSI C63.4 1992 NOTES: H = Horizontal Polarization Spec Limit : FCC Part 15.209 V = Vertical Polarization Test Distance: 3 Meters N = No Polarization D = Dipole Reading Q = Quasi Peak Reading A = Average Reading 1 = 12VDC 2 = 24VDC COMMENTS: EUT operating on 12 VDC & 24VDC via power supply. EUT operating in normal configuration, no card in the field. Frequency Range scanned from 30MHz – 1000MHz. Page 6 of 34 Report No: FC99-030

Table 3: Six Highest Conducted Emission Levels - 12 & 24 VDC METER CORRECTION FACTORS CORRECTED SPEC FREQUENCY READING Lisn Cable READING LIMIT MARGIN NOTES MHz dBµV dB dB dB dB dBµV dBµV dB 2.907180 37.7 0.0 0.10 37.8 48.0 -10.2 B-2 3.145198 38.0 0.0 0.10 38.1 48.0 -9.9 B-2 9.908866 40.2 0.0 0.20 40.4 48.0 -7.6 W-2 13.644450 40.7 0.0 0.20 40.9 48.0 -7.1 W-1 19.415950 41.0 0.0 0.30 41.3 48.0 -6.7 W-2 19.611300 38.0 0.0 0.30 38.3 48.0 -9.7 W-2 Test Method: ANSI C63.4 1992 NOTES: Q = Quasi Peak Reading Spec Limit : FCC 15.207 A = Average Reading B = Black Lead W = White Lead 1 = 12VDC 2 = 24VDC COMMENTS: EUT operating in normal mode with no card in the field. EUT operating on 12VDC & 24VDC via power supply. Page 7 of 34 Report No: FC99-030

TABLE A LIST OF TEST EQUIPMENT Mariposa Site B Industry Canada File No. IC 3082-D 1. Spectrum Analyzer, Hewlett Packard, Model No. 8566B, CKC 1, S/N 2403A08241 (Display Unit), S/N 2209A01404 (rf Unit). Calibration date: July 7, 1999. Calibration due date: July 7, 2000. 2. Preamp, Hewlett Packard, Model No. 8447D, S/N 1937A02604. Calibration Date: April 28, 1999. Calibration Due: April 28, 2000. 3. Quasi-Peak Adapter, Hewlett Packard, Model No. 85650A, S/N 2811A01267. Calibration Date: July 7, 1999. Calibration Due; July 7, 2000. 4. Biconical Antenna, A & H Systems, Model No. SAS-200/542, S/N 156. Calibration Date: May 20, 1999. Calibration Due: May 20, 2000. 5. Log Periodic Antenna, A & H Systems, Model No. SAS-200/512, S/N 154. Calibration date: May 20, 1999. Calibration Due: May 20, 2000. 6. Magnetic Loop Antenna, EMCO, Model 6502, S/N 1074. Calibration date: June 16, 1999. Calibration due date: June 16, 2000. 7. LISN (FCC), Solar Electronics, S/N 855996, 992. Calibration date: June 4, 1999. Calibration due date: June 4, 2000. 8. LISN, Solar Electronics, S/N 8144793, 474. Calibration date: June 2, 1999. Calibration due date: June 2, 2000. 9. Mariposa Site B (Barn). Calibration date: June 18, 1998. Calibration due date: June 18 2001. 10. Test software, EMI Test 3.08. Page 8 of 34 Report No: FC99-030

EUT SETUP The equipment under test (EUT) and the peripheral(s) listed were set up in a manner that represented their normal use. Any special conditions required for the EUT to operate normally are identified in the comments that accompany Tables 1-3 for l radiated and conducted emissions. Additionally, a complete description of all the ports and I/O cables is included on the information sheets contained in Appendix A. During radiated emissions testing, the EUT was mounted on a nonconductive, rotating table 80 cm above the conductive grid. The nonconductive table dimensions were 1 meter by 1.5 meters. This configuration is typical for radiated emissions testing of table top devices. I/O cables were connected to the EUT and peripherals in the manner required for normal operation of the system. Excess cabling was bundled in the center in a serpentine fashion using 30-40 centimeter lengths. During conducted emissions testing, the EUT was located on a wooden table measuring approximately 80 cm high, 1 meter deep, and 1.5 meters in length. One wall of the room where the EUT is located has a minimum 2 meter by 2 meter conductive plane. The EUT was mounted on the wooden table 40 cm away from the conductive plane, and 80 cm from any other conductive surface. The vertical metal plane used for conducted emissions was grounded to the earth. Power to the EUT was provided through a LISN. The LISN was grounded to the ground plane. All other objects were kept a minimum of 80 cm away from the EUT during the conducted test. Conducted emissions tests required the use of the LISN's listed in Table A. Page 9 of 34 Report No: FC99-030

TEST INSTRUMENTATION AND ANALYZER SETTINGS The test instrumentation and equipment listed in Table A were used to collect both the radiated and conducted emissions data for the RFID Proximity Reader, 5375A MaxiProx (5375-310-01). For radiated measurements below 300 MHz, the biconical antenna was used. For frequencies from 300 to 1000 MHz, the log periodic antenna was used. All antennas were located at a distance of 30 meters from the edge of the EUT while doing testing from 9kHz to 30 MHz, and 3 meters while doing testing from 30 MHz to 1 GHz. Conducted emissions tests required the use of the FCC type LISN's. The HP spectrum analyzer was used for all measurements. Table B shows the analyzer bandwidth settings that were used in designated frequency bands. For conducted emissions, an appropriate reference level and a vertical scale size of 10 dB per division were used. A 10 dB external attenuator was also used during conducted tests, with internal offset correction in the analyzer. During radiated testing, the measurements were made with 0 dB of attenuation, a reference level of 97 dBµV, and a vertical scale of 10 dB per division. TABLE B : ANALYZER BANDWIDTH SETTINGS PER FREQUENCY RANGE TEST BEGINNING FREQUENCY ENDING FREQUENCY BANDWIDTH SETTING CONDUCTED EMISSIONS 450 kHz 30 MHz 9 kHz RADIATED EMISSIONS 9 kHz 150 kHz 200 Hz RADIATED EMISSIONS 150 kHz 30 MHz 9 kHz RADIATED EMISSIONS 30 MHz 1000 MHz 120 kHz Page 10 of 34 Report No: FC99-030

SPECTRUM ANALYZER DETECTOR FUNCTIONS The notes that accompany the measurements contained in Tables 1-3 indicate the type of detector function used to obtain the given readings. Unless otherwise noted, all readings were made in the "Peak" mode. Whenever a "Quasi-Peak" or "Average" reading is listed as one of the highest readings, this is indicated as a "Q" or an "A" in the appropriate table. The following paragraphs describe in more detail the detector functions and when they were used to obtain the emissions data for the RFID Proximity Reader, 5375A MaxiProx (5375-310-01). Peak In this mode, the Spectrum Analyzer or test engineer recorded all emissions at their peak value as the frequency band selected was scanned. By combining this function with another feature of the analyzer called "peak hold," the analyzer had the ability to measure transients or low duty cycle transient emission peak levels. In this mode the analyzer made a slow scan across the frequency band selected and measured the peak emission value found at each frequency across the band. Quasi-Peak When the true peak values exceeded or were within 2 dB of the specification limit, quasi-peak measurements were taken using the HP Quasi-Peak Adapter for the HP Spectrum Analyzer. The detailed procedure for making quasi peak measurements contained in the HP Quasi-Peak Adapter manual were followed. Average When the frequencies are between 9-90 kHz, 110-490 kHz or exceed 1 GHz, average measurements may be made using the spectrum analyzer. To make these measurements, the test engineer reduces the video bandwidth on the analyzer until the modulation of the signal is filtered out. At this point the analyzer is set into the linear mode and the scan time is reduced. Page 11 of 34 Report No: FC99-030

TEST METHODS The radiated and conducted emissions data of the RFID Proximity Reader, 5375A MaxiProx (5375-310-01) was taken with the HP Spectrum Analyzer. Incorporating the applicable correction factors for distance, antenna, cable loss and amplifier gain, the data was reduced as shown in the "Sample Calculations". The corrected data was then compared to the FCC Part 15, Subpart C emissions limits to determine compliance. Preliminary and final measurements were taken in order to better ensure that all emissions from the EUT were found and maximized. Radiated Emissions Testing During the preliminary radiated scan, the EUT was powered up and operating in its defined FCC test mode with the I/O cables and line cords facing the antenna. The frequency range of 9 kHz – 30 MHz was scanned with the magnetic loop antenna. The frequency range of 30 MHz - 88 MHz was then scanned with the biconical antenna located about 1.5 meter above the ground plane in the vertical configuration. During this scan, the turntable was rotated and all peaks which were at or near the limit were recorded. The frequency range of 100 - 300 MHz was scanned with the biconical antenna in the same manner, and the peaks recorded. Lastly, a scan of the FM band from 88 - 110 MHz was made, using a reduced resolution bandwidth and a reduced frequency span. The biconical antenna was changed to the horizontal polarity and the above steps were repeated. After changing to the log periodic antenna in the horizontal configuration, the frequency range of 300 - 1000 MHz was scanned. The log periodic antenna was changed to the vertical polarity and the frequency range of 300 - 1000 MHz was again scanned. Care was taken to ensure that no frequencies were missed within the FM and TV bands. An analysis was performed to determine if the signals that were at or near the limit were caused by an ambient transmission. If unable to determine by analysis, the equipment was powered down to make the final determination if the EUT was the source of the emission. For the final radiated scan, the equipment was again positioned with its I/O and power cables facing the antenna. A thorough scan of all frequencies was manually made using a small frequency span, rotating the turntable as needed. Comparison with the previously recorded measurements was then made. Using the peak readings from both scans as a guide, the test engineer then maximized the readings with respect to the table rotation, antenna height and configuration of the peripherals and cables. Maximizing of the cables was achieved by monitoring the spectrum analyzer on a closed circuit television monitor while the EUT cables were being moved and rearranged on the EUT table for maximum emissions. Photographs showing the final worst case configuration of the EUT are contained in Appendix A. Page 12 of 34 Report No: FC99-030

Conducted Emissions Testing For conducted emissions testing, a 30 to 50 second sweep time was used for automated measurements in the frequency bands of 450 kHz to 1.705 MHz, 1.705 MHz to 3 MHz, and 3 MHz to 30 MHz. All readings within 20 dB of the limit were recorded. At frequencies where the recorded emissions were close to the limit, further investigation was performed manually at a slower sweep rate. SAMPLE CALCULATIONS The basic spectrum analyzer reading was converted using correction factors as shown in the emissions readings in Tables 1-3. For radiated emissions in dBµV/m, the spectrum analyzer reading in dBµV was corrected by using the following formula: Meter reading (dBµV) + Antenna Factor (dB) + Cable Loss (dB) - Distance Correction (dB) - Pre-amplifier Gain (dB) = Corrected Reading (dBµV/m) This reading was then compared to the applicable specification limit to determine compliance. A typical data sheet will display the following in column format: # Freq Rdng Cable Amp Bicon Mag Log Dist 15.31 Corr Spec Margin Polar MHz dBuV Loop dBuV/m # means reading number Freq MHz is the frequency in MHz of the obtained reading. Rdng dBuV is the reading obtained on the spectrum analyzer in dBµV. Amp is short for the preamplifier factor or gain in dB. Bicon is the biconical antenna factor in dB. Log is the log periodic antenna factor in dB. Mag Loop is the magnetic loop antenna factor in dB. Cable is the cable loss in dB of the coaxial cable on the OATS. Dist is the distance factor (in dB). It is used when testing at a different test distance than the one stated in the spec. Corr dBµ µV/m is the corrected reading which is now in dBµV/m (field strength). Spec is the specification limit (dB) stated in the agency's regulations. Margin is the closeness to the specified limit in dB; + is over and - is under the limit. Polar is the Polarity of the antenna with respect to earth. 15.31 is the FCC extraploation factor. Page 13 of 34 Report No: FC99-030

APPENDIX A INFORMATION ABOUT THE EQUIPMENT UNDER TEST Page 14 of 34 Report No: FC99-030

INFORMATION ABOUT THE EQUIPMENT UNDER TEST Test Software/Firmware: 5375-520-01 CRT was displaying: NA Power Supply Manufacturer: Customer Supplied Power Supply Part Number: AC Line Filter Manufacturer: NA AC Line Filter Part Number: NA Line voltage used during testing: 12 & 24 VDC I/O PORTS CRYSTAL OSCILLATORS Type # Type Freq In MHz DC Power & IO Signals 1 Crystal 4.00 PRINTED CIRCUIT BOARDS Function Model & Rev Clocks, MHz Layers Location All Rev. 3 4 4 0.001 CABLE INFORMATION Cable #: Cable(s) of this type: Cable Type: Shielded Shield Type: Foil with drain wire Construction: Multiconductor Length In Meters: * Connected To End (1): MaxiProx Connected To End (2): DC supply & controller Connector At End (1): None Connector At End (2): Shield Grounded At (1): TB1-2 Shield Grounded At (2): DC supply “-“ & chassis ground Part Number: Number of Conductors: 5 to 14 Notes: *Up to 152m for Wiegand, 15.2m for RS232, or 1,220m for RS422 REQUIRED EUT CHANGES TO COMPLY: None. Page 15 of 34 Report No: FC99-030

PHOTOGRAPH SHOWING RADIATED EMISSIONS Radiated Emissions - Front View Page 16 of 34 Report No: FC99-030

PHOTOGRAPH SHOWING RADIATED EMISSIONS Radiated Emissions - Back View Page 17 of 34 Report No: FC99-030

PHOTOGRAPH SHOWING CONDUCTED EMISSIONS Conducted Emissions - Front View Page 18 of 34 Report No: FC99-030

APPENDIX B MEASUREMENT DATA SHEETS Page 19 of 34 Report No: FC99-030

Test Location: CKC Laboratories, Inc / 5473A Clouds Rest / Mariposa, CA 95338• • • Customer: HID Specification: FCC 15 C PARA 15.209 Work Order #: 72268 Date: Mon Aug-30-1999 Test Type: Maximized Emissions Time: 16:51:41 Equipment: Proximity Reader Sequence#: 32 Manufacturer: HID Tested By: Dustin Oaks Model: 5375A S/N: N/A Equipment Under Test (* = EUT): Function Manufacturer Model # S/N Proximity Reader* HID 5375A N/A Support Devices: Function Manufacturer Model # S/N DC Power Supply Topward Electric 2306 920035 Instruments Test Conditions / Notes: EUT operating on 12/24VDC via DC power supply. EUT is in continuos read mode with no card in the field. 40dB correction factor IAW FCC 15.31. Frequency Range scanned from 9kHz to 30MHz. Measurement Data: Reading listed by order taken. Test Distance: 30 Meters Mag Cable 15.31 # Freq Rdng Loop Dist Corr Spec Margin Polar MHz dBµV dB dB dB dB Table dBµV/m dBµV/m dB Ant 1 124.968k 50.9 +12.2 +0.1 -40.0 +0.0 23.2 25.7 -2.5 None Ave EUT operating on 24VDC 2 124.982k 48.5 +12.2 +0.1 -40.0 +0.0 20.8 25.7 -4.9 None Ave EUT operating on 12VDC Page 20 of 34 Report No: FC99-030

Test Location: CKC Laboratories, Inc / 5473A Clouds Rest / Mariposa, CA 95338 • • • Customer: HID Specification: FCC 15.209 Work Order #: 72268 Date: Mon Aug-30-1999 Test Type: Maximized Emissions Time: 16:58:37 Equipment: Proximity Reader Sequence#: 34 Manufacturer: HID Tested By: Dustin Oaks Model: 5375A S/N: N/A Equipment Under Test (* = EUT): Function Manufacturer Model # S/N Proximity Reader* HID 5375A N/A Support Devices: Function Manufacturer Model # S/N DC Power Supply Topward Electric 2306 920035 Instruments Test Conditions / Notes: EUT operating on 12VDC via power supply. EUT operating in normal configuration, no card in the field. Measurement Data: Reading listed by order taken. Test Distance: 3 Meters Amp Bicon Log Cable # Freq Rdng Dist Corr Spec Margin Polar MHz dBµV dB dB dB dB Table dBµV/m dBµV/m dB Ant 1 56.219M 43.2 -26.8 +9.8 +0.0 +1.3 +0.0 27.5 40.0 -12.5 Vert 2 32.064M 42.6 -27.0 +12.8 +0.0 +1.0 +0.0 29.4 40.0 -10.6 Vert 3 43.870M 38.3 -27.0 +10.7 +0.0 +1.2 +0.0 23.2 40.0 -16.8 Vert 4 150.042M 36.1 -26.8 +12.7 +0.0 +2.2 +0.0 24.2 43.5 -19.3 Vert 5 108.813M 32.3 -26.8 +12.7 +0.0 +1.9 +0.0 20.1 43.5 -23.4 Vert 6 134.956M 33.2 -26.8 +13.6 +0.0 +2.1 +0.0 22.1 43.5 -21.4 Vert Page 21 of 34 Report No: FC99-030

Test Location: CKC Laboratories, Inc / 5473A Clouds Rest / Mariposa, CA 95338• • • Customer: HID Specification: FCC 15.209 Work Order #: 72268 Date: Mon Aug-30-1999 Test Type: Maximized Emissions Time: 14:50:44 Equipment: Proximity Reader Sequence#: 29 Manufacturer: HID Tested By: Dustin Oaks Model: 5375A S/N: N/A Equipment Under Test (* = EUT): Function Manufacturer Model # S/N Proximity Reader* HID 5375A N/A Support Devices: Function Manufacturer Model # S/N DC Power Supply Topward Electric 2306 920035 Instruments Test Conditions / Notes: EUT operating on 24VDC via power supply. EUT operating in normal configuration, no card in the field. Measurement Data: Reading listed by order taken. Test Distance: 3 Meters Amp Bicon Log Cable # Freq Rdng Dist Corr Spec Margin Polar MHz dBµV dB dB dB dB Table dBµV/m dBµV/m dB Ant 1 32.056M 40.2 -27.0 +12.8 +0.0 +1.0 +0.0 27.0 40.0 -13.0 Vert 2 43.846M 39.3 -27.0 +10.7 +0.0 +1.2 +0.0 24.2 40.0 -15.8 Vert 3 143.300M 31.5 -26.8 +13.2 +0.0 +2.1 +0.0 20.0 43.5 -23.5 Vert 4 150.037M 34.0 -26.8 +12.7 +0.0 +2.2 +0.0 22.1 43.5 -21.4 Vert 5 134.946M 31.5 -26.8 +13.6 +0.0 +2.1 +0.0 20.4 43.5 -23.1 Vert 6 108.806M 32.6 -26.8 +12.7 +0.0 +1.9 +0.0 20.4 43.5 -23.1 Vert 7 43.879M 39.4 -27.0 +10.7 +0.0 +1.2 +0.0 24.3 40.0 -15.7 Vert 8 56.217M 44.3 -26.8 +9.8 +0.0 +1.3 +0.0 28.6 40.0 -11.4 Vert Page 22 of 34 Report No: FC99-030

Test Location: CKC Laboratories, Inc / 5473A Clouds Rest / Mariposa, CA 95338 • • • Customer: HID Specification: FCC 15.207 Work Order #: 72268 Date: Thur Sep-02-1999 Test Type: Conducted Emissions Time: 18:35:41 Equipment: Proximity Reader Sequence#: 44 Manufacturer: HID Tested By: Dustin Oaks Model: 5375A S/N: N/A Equipment Under Test (* = EUT): Function Manufacturer Model # S/N Proximity Reader* HID 5375A N/A Support Devices: Function Manufacturer Model # S/N DC Power Supply Topward Electric 2306 920035 Instruments Test Conditions / Notes: EUT operating in normal mode with no card in the field. EUT operating on 12VDC via power supply. Measurement Data: Reading listed by margin. Test Lead: Black Cable # Freq Rdng Dist Corr Spec Margin Polar MHz dBµV dB dB dB dB Table dBµV/m dBµV/m dB Ant 1 13.644M 38.4 +0.2 +0.0 38.6 48.0 -9.4 Black 2 11.783M 34.6 +0.2 +0.0 34.8 48.0 -13.2 Black 3 9.611M 34.4 +0.2 +0.0 34.6 48.0 -13.4 Black 4 11.674M 33.8 +0.2 +0.0 34.0 48.0 -14.0 Black 5 4.395M 33.7 +0.1 +0.0 33.8 48.0 -14.2 Black 6 9.949M 33.4 +0.2 +0.0 33.6 48.0 -14.4 Black 7 8.758M 33.4 +0.2 +0.0 33.6 48.0 -14.4 Black 8 556.608k 33.5 +0.1 +0.0 33.6 48.0 -14.4 Black 9 14.000M 33.3 +0.2 +0.0 33.5 48.0 -14.5 Black 10 1.493M 33.4 +0.1 +0.0 33.5 48.0 -14.5 Black 11 14.888M 33.2 +0.2 +0.0 33.4 48.0 -14.6 Black 12 12.757M 33.2 +0.2 +0.0 33.4 48.0 -14.6 Black 13 16.379M 33.0 +0.3 +0.0 33.3 48.0 -14.7 Black 14 26.821M 32.9 +0.3 +0.0 33.2 48.0 -14.8 Black Page 23 of 34 Report No: FC99-030

15 6.259M 33.0 +0.2 +0.0 33.2 48.0 -14.8 Black Page 24 of 34 Report No: FC99-030

ore Te mceimTe naras worme ree mar Hex las ta Soaweer o sowam snsaore wo wooe ns ns sns

Test Location: CKC Laboratories, Inc / 5473A Clouds Rest / Mariposa, CA 95338 • • • Customer: HID Specification: FCC 15.207 Work Order #: 72268 Date: Thu Sep-02-1999 Test Type: Conducted Emissions Time: 18:40:04 Equipment: Proximity Reader Sequence#: 45 Manufacturer: HID Tested By: Dustin Oaks Model: 5375A S/N: N/A Equipment Under Test (* = EUT): Function Manufacturer Model # S/N Proximity Reader* HID 5375A N/A Support Devices: Function Manufacturer Model # S/N DC Power Supply Topward Electric 2306 920035 Instruments Test Conditions / Notes: EUT operating in normal mode with no card in the field. EUT operating on 12VDC via power supply. Measurement Data: Reading listed by margin. Test Lead: White Cable # Freq Rdng Dist Corr Spec Margin Polar MHz dBµV dB dB dB dB Table dBµV/m dBµV/m dB Ant 1 13.644M 40.7 +0.2 +0.0 40.9 48.0 -7.1 White 2 9.919M 37.9 +0.2 +0.0 38.1 48.0 -9.9 White 3 11.873M 37.5 +0.2 +0.0 37.7 48.0 -10.3 White 4 9.611M 37.5 +0.2 +0.0 37.7 48.0 -10.3 White 5 15.030M 36.0 +0.3 +0.0 36.3 48.0 -11.7 White 6 9.830M 34.4 +0.2 +0.0 34.6 48.0 -13.4 White 7 16.876M 34.0 +0.3 +0.0 34.3 48.0 -13.7 White 8 11.674M 33.9 +0.2 +0.0 34.1 48.0 -13.9 White 9 9.512M 33.6 +0.2 +0.0 33.8 48.0 -14.2 White 10 12.508M 33.5 +0.2 +0.0 33.7 48.0 -14.3 White 11 2.137M 33.6 +0.1 +0.0 33.7 48.0 -14.3 White 12 28.704M 33.2 +0.4 +0.0 33.6 48.0 -14.4 White 13 24.086M 33.2 +0.4 +0.0 33.6 48.0 -14.4 White 14 20.819M 33.3 +0.3 +0.0 33.6 48.0 -14.4 White Page 26 of 34 Report No: FC99-030

15 11.337M 33.3 +0.2 +0.0 33.5 48.0 -14.5 White Page 27 of 34 Report No: FC99-030

ore Te mczim me nae wornie ree mar Hex lwee Soaweer a sowam snsaore wo wooe ns ns sns

Test Location: CKC Laboratories, Inc / 5473A Clouds Rest / Mariposa, CA 95338 • • • Customer: HID Specification: FCC 15.207 Work Order #: 72268 Date: Thu Sep-02-1999 Test Type: Conducted Emissions Time: 18:33:00 Equipment: Proximity Reader Sequence#: 43 Manufacturer: HID Tested By: Dustin Oaks Model: 5375A S/N: N/A Equipment Under Test (* = EUT): Function Manufacturer Model # S/N Proximity Reader* HID 5375A N/A Support Devices: Function Manufacturer Model # S/N DC Power Supply Topward Electric 2306 920035 Instruments Test Conditions / Notes: EUT operating in normal mode with no card in the field. EUT operating on 24VDC via power supply. Measurement Data: Reading listed by margin. Test Lead: White Cable # Freq Rdng Dist Corr Spec Margin Polar MHz dBµV dB dB dB dB Table dBµV/m dBµV/m dB Ant 1 19.150M 47.9 +0.3 +0.0 48.2 48.0 +0.2 White 2 19.416M 41.0 +0.3 +0.0 41.3 48.0 -6.7 White 3 9.909M 40.2 +0.2 +0.0 40.4 48.0 -7.6 White 4 13.644M 39.5 +0.2 +0.0 39.7 48.0 -8.3 White 5 19.611M 38.0 +0.3 +0.0 38.3 48.0 -9.7 White 6 12.508M 37.3 +0.2 +0.0 37.5 48.0 -10.5 White 7 15.278M 37.0 +0.3 +0.0 37.3 48.0 -10.7 White 8 13.751M 37.1 +0.2 +0.0 37.3 48.0 -10.7 White 9 20.144M 36.3 +0.3 +0.0 36.6 48.0 -11.4 White 10 11.873M 36.2 +0.2 +0.0 36.4 48.0 -11.6 White 11 11.754M 35.9 +0.2 +0.0 36.1 48.0 -11.9 White 12 11.674M 35.6 +0.2 +0.0 35.8 48.0 -12.2 White 13 2.391M 35.7 +0.1 +0.0 35.8 48.0 -12.2 White 14 2.125M 35.4 +0.1 +0.0 35.5 48.0 -12.5 White Page 29 of 34 Report No: FC99-030

15 12.011M 35.2 +0.2 +0.0 35.4 48.0 -12.6 White 16 19.150M 26.0 +0.3 +0.0 26.3 48.0 -21.7 White QP Page 30 of 34 Report No: FC99-030

ore Te mcem me wass wornie ree mar es lwee Sowea sowam snsaore wo wooe ns ns sns

Test Location: CKC Laboratories, Inc / 5473A Clouds Rest / Mariposa, CA 95338 • • • Customer: HID Specification: FCC 15.207 Work Order #: 72268 Date: Thu Sep-02-1999 Test Type: Conducted Emissions Time: 18:27:20 Equipment: Proximity Reader Sequence#: 42 Manufacturer: HID Tested By: Dustin Oaks Model: 5375A S/N: N/A Equipment Under Test (* = EUT): Function Manufacturer Model # S/N Proximity Reader* HID 5375A N/A Support Devices: Function Manufacturer Model # S/N DC Power Supply Topward Electric 2306 920035 Instruments Test Conditions / Notes: EUT operating in normal mode with no card in the field. EUT operating on 24VDC via power supply. Measurement Data: Reading listed by margin. Test Lead: Black Cable # Freq Rdng Dist Corr Spec Margin Polar MHz dBµV dB dB dB dB Table dBµV/m dBµV/m dB Ant 1 3.145M 38.0 +0.1 +0.0 38.1 48.0 -9.9 Black 2 2.907M 37.7 +0.1 +0.0 37.8 48.0 -10.2 Black 3 3.403M 37.0 +0.1 +0.0 37.1 48.0 -10.9 Black 4 13.609M 36.4 +0.2 +0.0 36.6 48.0 -11.4 Black 5 19.931M 35.5 +0.3 +0.0 35.8 48.0 -12.2 Black 6 2.659M 35.7 +0.1 +0.0 35.8 48.0 -12.2 Black 7 14.994M 35.3 +0.3 +0.0 35.6 48.0 -12.4 Black 8 20.464M 35.2 +0.3 +0.0 35.5 48.0 -12.5 Black 9 20.286M 35.0 +0.3 +0.0 35.3 48.0 -12.7 Black 10 3.641M 35.2 +0.1 +0.0 35.3 48.0 -12.7 Black 11 29.982M 34.6 +0.3 +0.0 34.9 48.0 -13.1 Black 12 4.137M 34.8 +0.1 +0.0 34.9 48.0 -13.1 Black 13 19.327M 34.5 +0.3 +0.0 34.8 48.0 -13.2 Black 14 6.269M 34.6 +0.2 +0.0 34.8 48.0 -13.2 Black Page 32 of 34 Report No: FC99-030

15 2.123M 34.6 +0.1 +0.0 34.7 48.0 -13.3 Black Page 33 of 34 Report No: FC99-030

ore Te mceimTe zza wormie ree mar Hex baa ta Sower a sowam snsaore wo wooe ns ns sns


Document Created: 1999-10-08 10:29:55
Document Modified: 1999-10-08 10:29:55
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC