Test Setup Photos on Pages 17 and 18

FCC ID: JQ6535Y

Test Setup Photos

Download: PDF
FCCID_124763

ADDENDUM TO TEST REPORT FC99-014 FOR THE PROXPRO, 5355/8A (5355-300) FCC PART 15 SUBPART C SECTION 15.207/15.209 COMPLIANCE DATE OF ISSUE: SEPTEMBER 19, 2000 PREPARED FOR: PREPARED BY: HID Corporation Joyce Walker 9292 Jeronimo CKC Laboratories, Inc. Irvine, CA 92618-1905 5473A Clouds Rest Mariposa, CA 95338 P.O. No: 007532 W.O. No: 70946 Date of test: February 18, 25, 1999 Report No: FC99-014A DOCUMENTATION CONTROL: APPROVED BY: _____________________________ _____________________________ Tracy Phillips Dennis Ward Documentation Control Supervisor Director of Laboratories CKC Laboratories, Inc. CKC Laboratories, Inc. This report contains a total of 25 pages and may be reproduced in full only. Partial reproduction may only be done with the written consent of CKC Laboratories, Inc. Page 1 of 25 Report No: FC99-014A

TABLE OF CONTENTS Administrative Information .............................................................................................3 Summary Of Results........................................................................................................4 Equipment Under Test (EUT) Description......................................................................4 Measurement Uncertainty................................................................................................4 EUT Operating Frequency...............................................................................................4 Peripheral Devices...........................................................................................................5 Report Of Measurements.................................................................................................6 Table 1: Six Highest Radiated Emission Levels – 9kHz-30MHz .......................6 Table 2: Six Highest Radiated Emission Levels - 30MHz-1000MHz ................7 Table 3: Six Highest Conducted Emission Levels ..............................................8 Table A : List Of Test Equipment ...................................................................................9 EUT Setup .......................................................................................................................10 Test Instrumentation And Analyzer Settings...................................................................10 Table B : Analyzer Bandwidth Settings Per Frequency Range...........................11 Spectrum Analyzer Detector Functions...............................................................11 Peak .........................................................................................................11 Quasi-Peak...............................................................................................11 Average....................................................................................................12 Test Methods ...................................................................................................................12 Radiated Emissions Testing.................................................................................12 Conducted Emissions Testing .............................................................................13 Sample Calculations ........................................................................................................13 Appendix A : Information About The Equipment Under Test........................................15 I/O Ports...............................................................................................................16 Crystal Oscillators ...............................................................................................16 Printed Circuit Boards .........................................................................................16 Required EUT Changes To Comply....................................................................16 Photograph Showing Radiated Emissions...........................................................17 Photograph Showing Conducted Emissions........................................................18 Appendix B: Measurement Data Sheets..........................................................................19 Page 2 of 25 Report No: FC99-014A

CKC Laboratories, Inc. has Certificates of Accreditation from the following agencies: DATech (Germany); A2LA (USA); FCC (USA); VCCI (Japan); BSMI (Taiwan); HOKLAS (Hong Kong). CKC Laboratories, Inc. has Letters of Acceptance through an MRA for the following agencies: ACA/NATA (Australia); SABS (South Africa); SWEDAC (Sweden); TUV Rheinland-Germany; TUV Rheinland- Korea; TUV Rheinland-Russia; Radio Communication Agency (RA); NEMKO (Norway). ADMINISTRATIVE INFORMATION DATE OF TEST: February 18, 25, 1999 PURPOSE OF TEST: To demonstrate the compliance of the ProxPro, 5355/8A (5355-300), with the requirements for FCC Part 15 Subpart C Sections 15.207/15.209 devices. The addendum is to accommodate product name changes by the manufacturer. MANUFACTURER: HID Corporation 9292 Jeronimo Irvine, CA 92618-1905 REPRESENTATIVE: Frank de Vall TEST LOCATION: CKC Laboratories, Inc. 5473A Clouds Rest Mariposa, CA 95338 TEST PERSONNEL: Dustin Oaks TEST METHOD: ANSI C63.4 1992 FREQUENCY RANGE TESTED: 9 kHz - 1000 MHz EQUIPMENT UNDER TEST: ProxPro Manuf: HID Corporation Model: 5355/8A (5355-300) Serial: N/A FCC ID: JQ6535Y (pending) Page 3 of 25 Report No: FC99-014A

SUMMARY OF RESULTS The HID Corporation ProxPro, 5355/8A (5355-300), was tested in accordance with ANSI C63.4 1992 for compliance with FCC Part 15 Subpart C Sections 15.207/15.209. As received, the above equipment was found to be fully compliant with the limits of FCC Part 15 Subpart C Sections 15.207/15.209. The results in this report apply only to the items tested, as identified herein. EQUIPMENT UNDER TEST (EUT) DESCRIPTION RFID Access Control Reader. The following model has been tested by CKC Laboratories: Prox Reader, 5355/8B The following additional model is identical electrically to the one, which was tested, or any differences between them do not affect their EMC characteristics, and therefore they comply with the level of testing equivalent to the tested models. ProxPro, 5355/8A (5355-300) MEASUREMENT UNCERTAINTY Associated with data in this report is a ±4dB measurement uncertainty. EUT OPERATING FREQUENCY The EUT was operating at 125 kHz. TEMPERATURE AND HUMIDITY DURING TESTING The temperature during testing was within +15°C and + 35°C. The relative humidity was between 20% and 75%. Page 4 of 25 Report No: FC99-014A

PERIPHERAL DEVICES The EUT was tested with the following peripheral device(s): Power Supply Power Supply Manuf: Sorensen Manuf: Topward Electronic Instruments Model: DCR60 - 30B Model: 2306 Serial: 0176 Serial: 920035 FCC ID: N/A FCC ID: N/A Page 5 of 25 Report No: FC99-014A

REPORT OF MEASUREMENTS The following tables report the six highest worst case levels recorded during the tests performed on the ProxPro, 5355/8A (5355-300). All readings taken are peak readings unless otherwise noted by a “Q” or “A”. The data sheets from which these tables were compiled are contained in Appendix B. Table 1: Six Highest Radiated Emission Levels - 9kHz-30MHz METER CORRECTION FACTORS CORRECTED SPEC FREQUENCY READING Mag Cable FCC Dist READING LIMIT MARGIN NOTES 15.31 MHz dBµV dB dB dB dB dBµV/m dBµV/m dB 0.125 42.5 12.2 0.1 -40.0 14.8 25.7 -10.9 N 0.375 28.2 14.3 0.1 -40.0 2.6 16.1 -13.5 N 0.500 6.8 12.8 0.2 0.0 19.8 33.6 -13.8 N 0.625 9.9 11.6 0.2 0.0 21.7 31.7 -10.0 N 0.750 0.5 10.7 0.2 0.0 11.4 30.1 -18.7 N 0.875 7.5 10.0 0.2 0.0 17.7 28.7 -11.0 N Test Method: ANSI C63.4 1992 NOTES: N = No Polarization Spec Limit : FCC Part 15.209 Test Distance: 30 Meters COMMENTS: EUT operating in normal mode. No Proxcard in field. EUT receiving operating voltage of 24VDC via power supply. 40dB/Dec correction used in accordance to FCC Part 15.31. Page 6 of 25 Report No: FC99-014A

Table 2: Six Highest Radiated Emission Levels - 30MHz-1000MHz METER CORRECTION FACTORS CORRECTED SPEC FREQUENCY READING Amp Ant Cable Dist READING LIMIT MARGIN NOTES MHz dBµV dB dB dB dBµV/m dBµV/m dB 33.940 49.4 -27.3 12.6 1.0 35.7 40.0 -4.3 VQ 48.063 46.5 -27.2 11.0 1.3 31.6 40.0 -8.4 VQ 65.072 49.3 -27.2 8.9 1.4 32.4 40.0 -7.6 VQ 119.976 45.5 -27.2 13.8 2.0 34.1 43.5 -9.4 V 188.025 42.0 -26.8 16.7 2.6 34.5 43.5 -9.0 V 192.037 41.4 -26.8 17.1 2.6 34.3 43.5 -9.2 V Test Method: ANSI C63.4 1992 NOTES: Q = Quasi Peak Reading Spec Limit : FCC Part 15.209 V = Vertical Polarization Test Distance: 3 Meters COMMENTS: EUT operating in normal mode. No Proxcard in field. EUT receiving operating voltage of 24VDC via power supply. Page 7 of 25 Report No: FC99-014A

Table 3: Six Highest Conducted Emission Levels METER CORRECTION FACTORS CORRECTED SPEC FREQUENCY READING Lisn READING LIMIT MARGIN NOTES MHz dBµV dB dB dB dB dBµV dBµV dB 8.509804 34.1 0.0 34.1 48.0 -13.9 W 11.511150 35.4 0.0 35.4 48.0 -12.6 B 11.639690 34.2 0.0 34.2 48.0 -13.8 B 15.142350 34.2 0.0 34.2 48.0 -13.8 W 15.640430 35.0 0.0 35.0 48.0 -13.0 W 16.636600 35.6 0.0 35.6 48.0 -12.4 W Test Method: ANSI C63.4 1992 NOTES: B = Black Lead Spec Limit : FCC Part 15.207 W = White Lead Test Distance: No Distance COMMENTS: EUT is operating in normal operating mode. No Proxcard located in field. EUT received operating voltage of 24VDC via power supply. Negative power lead from EUT tied to DC power supply chassis ground. Page 8 of 25 Report No: FC99-014A

TABLE A LIST OF TEST EQUIPMENT 1. Spectrum Analyzer, Hewlett Packard, Model No. 8566B, S/N 2209A01404. Calibration date: June 12, 1998. Calibration due date: June 12, 1999. 2. Preamp, Hewlett Packard, Model No. 8447D, S/N 1937A02604. Calibration date: April 10, 1998. Calibration due date: April 10, 1999. 3. Quasi-Peak Adapter, Hewlett Packard, Model No. 85650A, S/N 2811A01267. Calibration date: June 12, 1998. Calibration due date: June 12, 1999. 4. Biconical Antenna, A & H Systems, Model No. SAS-200/542, S/N 156. Calibration date: June 9, 1998. Calibration due date: June 9, 1999. 5. Log Periodic Antenna, A & H Systems, Model No. SAS-200/512, S/N 154. Calibration date: June 9, 1998. Calibration due date: June 9, 1999. 6. Magnetic Loop Antenna, EMCO, Model No. 6502, S/N 1074. Calibration date: May 11, 1998. Calibration due date: May 11, 1999. 7. LISN (FCC), Solar Electronics, S/N 855996, 992. Calibration date: May 28, 1998. Calibration due date: May 28, 1999. Page 9 of 25 Report No: FC99-014A

EUT SETUP The equipment under test (EUT) and the peripheral(s) listed were set up in a manner that represented their normal use. Any special conditions required for the EUT to operate normally are identified in the comments that accompany Table 1-3 for radiated and conducted emissions. Additionally, a complete description of all the ports and I/O cables is included on the information sheets contained in Appendix A. During radiated emissions testing, the EUT was mounted on a nonconductive, rotating table 80 cm above the conductive grid. The nonconductive table dimensions were 1 meter by 1.5 meters. This configuration is typical for radiated emissions testing of wall mounted devices. I/O cables were connected to the EUT and peripheral in the manner required for normal operation of the system. Excess cabling was bundled in the center in a serpentine fashion using 30-40 centimeter lengths. During conducted emissions testing, the EUT was located on a wooden table measuring approximately 80 cm high, 1 meter deep, and 1.5 meters in length. One wall of the room where the EUT is located has a minimum 2-meter by 2-meter conductive plane. The EUT was mounted on the wooden table 40 cm away from the conductive plane, and 80 cm from any other conductive surface. The vertical metal plane used for conducted emissions was grounded to the earth. Power to the EUT was provided through a LISN. The LISN was grounded to the ground plane. All other objects were kept a minimum of 80 cm away from the EUT during the conducted test. Conducted emissions tests required the use of the LISN's listed in Table A. TEST INSTRUMENTATION AND ANALYZER SETTINGS The test instrumentation and equipment listed in Table A were used to collect both the radiated and conducted emissions data for the ProxPro, 5355/8A (5355-300). For frequencies below 30 MHz, the magnetic loop antenna was used. For radiated measurements below 300 MHz, the biconical antenna was used. For frequencies from 300 to 1000 MHz, the log periodic antenna was used. All antennas were located at a distance of 30 meters from the edge of the EUT while doing testing from 9kHz to 30 MHz, and 3 meters while doing testing from 30 MHz to 1 GHz. Conducted emissions tests required the use of the FCC type LISN's. Page 10 of 25 Report No: FC99-014A

The HP spectrum analyzer was used for all measurements. Table B shows the analyzer bandwidth settings that were used in designated frequency bands. For conducted emissions, an appropriate reference level and a vertical scale size of 10 dB per division were used. A 10 dB external attenuator was also used during conducted tests, with internal offset correction in the analyzer. During radiated testing, the measurements were made with 0 dB of attenuation, a reference level of 97 dBµV, and a vertical scale of 10 dB per division. TABLE B : ANALYZER BANDWIDTH SETTINGS PER FREQUENCY RANGE TEST BEGINNING FREQUENCY ENDING FREQUENCY BANDWIDTH SETTING CONDUCTED EMISSIONS 450 kHz 30 MHz 9 kHz RADIATED EMISSIONS 9 kHz 150 kHz 200 Hz RADIATED EMISSIONS 150 kHz 30 MHz 9 kHz RADIATED EMISSIONS 30 MHz 1000 MHz 120 kHz SPECTRUM ANALYZER DETECTOR FUNCTIONS The notes that accompany the measurements contained in Tables 1, 2 and 3 indicate the type of detector function used to obtain the given readings. Unless otherwise noted, all readings were made in the "Peak" mode. Whenever a "Quasi-Peak" or "Average" reading is listed as one of the six highest readings, this is indicated as a "Q" or an "A" in the appropriate table. The following paragraphs describe in more detail the detector functions and when they were used to obtain the emissions data for the ProxPro, 5355/8A (5355-300). Peak In this mode, the Spectrum Analyzer or test engineer recorded all emissions at their peak value as the frequency band selected was scanned. By combining this function with another feature of the analyzer called "peak hold," the analyzer had the ability to measure transients or low duty cycle transient emission peak levels. In this mode the analyzer made a slow scan across the frequency band selected and measured the peak emission value found at each frequency across the band. Quasi-Peak When the true peak values exceeded or were within 2 dB of the specification limit, quasi-peak measurements were taken using the HP Quasi-Peak Adapter for the HP Spectrum Analyzer. The detailed procedure for making quasi peak measurements contained in the HP Quasi-Peak Adapter manual were followed. Page 11 of 25 Report No: FC99-014A

Average When the frequencies are below 30 MHz, average measurements may be made using the spectrum analyzer. To make these measurements, the test engineer reduces the video bandwidth on the analyzer until the modulation of the signal is filtered out. At this point the analyzer is set into the linear mode and the scan time is reduced. TEST METHODS The radiated and conducted emissions data of the ProxPro, 5355/8A (5355-300), was taken with the HP Spectrum Analyzer. Incorporating the applicable correction factors for distance, antenna, cable loss and amplifier gain, the data was reduced as shown in the "Sample Calculations". The corrected data was then compared to the FCC Part 15 Subpart C Sections 15.207/15.209 emissions limits to determine compliance. Preliminary and final measurements were taken in order to better ensure that all emissions from the EUT were found and maximized. Radiated Emissions Testing During the preliminary radiated scan, the EUT was powered up and operating in its defined FCC test mode with the I/O cables and power cable facing the antenna. The frequency range of 9 kHz to 30 MHz was scanned with the magnetic loop antenna. The frequency range of 30 MHz - 88 MHz was then scanned with the biconical antenna located about 1.5 meter above the ground plane in the vertical configuration. During this scan, the turntable was rotated and all peaks, which were at or near the limit, were recorded. The frequency range of 100 - 300 MHz was scanned with the biconical antenna in the same manner, and the peaks recorded. Lastly, a scan of the FM band from 88 - 110 MHz was made, using a reduced resolution bandwidth and a reduced frequency span. The biconical antenna was changed to the horizontal polarity and the above steps were repeated. After changing to the log periodic antenna in the horizontal configuration, the frequency range of 300 - 1000 MHz was scanned. The log periodic antenna was changed to the vertical polarity and the frequency range of 300 - 1000 MHz was again scanned. Care was taken to ensure that no frequencies were missed within the FM and TV bands. An analysis was performed to determine if the signals that were at or near the limit were caused by an ambient transmission. If unable to determine by analysis, the equipment was powered down to make the final determination if the EUT was the source of the emission. For the final radiated scan, the equipment was again positioned with its I/O and power cables facing the antenna. A thorough scan of all frequencies was manually made using a small frequency span, rotating the turntable as needed. Comparison with the previously recorded measurements was then made. Page 12 of 25 Report No: FC99-014A

Using the peak readings from both scans as a guide, the test engineer then maximized the readings with respect to the table rotation, antenna height and configuration of the peripheral and cables. Maximizing of the cables was achieved by monitoring the spectrum analyzer on a closed circuit television monitor while the EUT cables were being moved and rearranged on the EUT table for maximum emissions. Photographs showing the final worst case configuration of the EUT are contained in Appendix A. Conducted Emissions Testing For conducted emissions testing, a 30 to 50 second sweep time was used for automated measurements in the frequency bands of 450 kHz to 1.705 MHz, 1.705 MHz to 3 MHz, and 3 MHz to 30 MHz. All readings within 20 dB of the limit were recorded. At frequencies where the recorded emissions were close to the limit, further investigation was performed manually at a slower sweep rate. SAMPLE CALCULATIONS The basic spectrum analyzer reading was converted using correction factors as shown in the emissions readings in Tables 1, 2 and 3. For radiated emissions in dBµV/m, the spectrum analyzer reading in dBµV was corrected by using the following formula: Meter reading (dBµV) + Antenna Factor (dB) + Cable Loss (dB) - Distance Correction (dB) - Pre-amplifier Gain (dB) = Corrected Reading (dBµV/m) This reading was then compared to the applicable specification limit to determine compliance. Page 13 of 25 Report No: FC99-014A

A typical data sheet will display the following in column format: # Freq Rdng Cable Amp Bicon Mag FCC Dist Corr Spec Margin Polar MHz dBuV 15.31 dBuV/m LISN # means reading number Freq MHz is the frequency in MHz of the obtained reading. Rdng dBuV is the reading obtained on the spectrum analyzer in dBµV. Amp is short for the preamplifier factor or gain in dB. Bicon is the biconical antenna factor in dB. FCC 15.31 is 40dB/Dec correction used in accordance with 15.31. Mag is the magnetic loop antenna factor in dB. Cable is the cable loss in dB of the coaxial cable on the OATS. Dist is the distance factor (in dB). It is used when testing at a different test distance than the one stated in the spec. Corr dBµ µV/m is the corrected reading which is now in dBµV/m (field strength). Spec is the specification limit (dB) stated in the agency's regulations. Margin is the closeness to the specified limit in dB; + is over and - is under the limit. Polar is the Polarity of the antenna with respect to earth. FCC 15.31 is the average correction called in FCC Part 15.31. LISN is the line impedance stabilization network factor in dB. Page 14 of 25 Report No: FC99-014A

APPENDIX A INFORMATION ABOUT THE EQUIPMENT UNDER TEST Page 15 of 25 Report No: FC99-014A

INFORMATION ABOUT THE EQUIPMENT UNDER TEST Test Software/Firmware: None CRT was displaying: NA Power Supply Manufacturer: Customer Supplied Power Supply Part Number: NA AC Line Filter Manufacturer: NA AC Line Filter Part Number: NA Voltage used during testing: 24VDC I/O PORTS CRYSTAL OSCILLATORS Type # Type Freq In MHz DC Power & Signals 1 Ceramic Resonator 4 MHz PRINTED CIRCUIT BOARDS Function Model & Rev Clocks, MHz Layers Location All Electronics Rev B 4 MHz 4 CABLE INFORMATION Cable #: Cable(s) of this type: Cable Type: Shielded Shield Type: Foil with Drain Construction: Multiconductor Length In Meters: 152 Connected To End (1): Reader Connected To End (2): DC Supply and Controller Connector At End (1): None Connector At End (2): None Shield Grounded At (1): Shield Ground Shield Grounded At (2): NC Part Number: Number of Conductors: 6 to 10 Notes: REQUIRED EUT CHANGES TO COMPLY: None. Page 16 of 25 Report No: FC99-014A

PHOTOGRAPH SHOWING RADIATED EMISSIONS Radiated Emissions - Front View Page 17 of 25 Report No: FC99-014A

PHOTOGRAPH SHOWING CONDUCTED EMISSIONS Conducted Emissions - Front View Page 18 of 25 Report No: FC99-014A

APPENDIX B MEASUREMENT DATA SHEETS Page 19 of 25 Report No: FC99-014A

Test Location: CKC Laboratories, Inc. • 5473A Clouds Rest Rd, Barn • Mariposa, CA 95338 • (800)-500- 4EMC Customer: HID Corporation Date: Feb-18-99 Specification: FCC 15.209 Time: 10:46 Test Type: Maximized Emissions Sequence#: 17 Equipment: Proximity Reader Manufacturer: HID Tested By: Dustin Oaks Model: 5355/8B S/N: N/A Equipment Under Test (* = EUT): Function Manufacturer Model # S/N Proximity Reader* HID 5355/8B N/A Support Devices: Function Manufacturer Model # S/N Power Supply Sorensen DCR60 - 30B 0176 Test Conditions / Notes: EUT operating in normal mode. No Proxcard in field. EUT receiving operating voltage of 24VDC via power supply. 40dB/Dec correction used in accordance with FCC Part 15.31. Measurement Data: Sorted by Margin Test Distance: 30 Meters FCC 15.31 # Freq Rdng Mag Cable Dist Corr Spec Margin Polar dBµV dB dB dB dB dB dBµV/m dBµV/m dB 1 625.144k 9.9 +11.6 +0.2 +0.0 +0.0 21.7 31.7 -10.0 None 2 125.009k 42.5 +12.2 +0.1 -40.0 +0.0 14.8 25.7 -10.9 None 3 874.973k 7.5 +10.0 +0.2 +0.0 +0.0 17.7 28.7 -11.0 None 4 374.985k 28.2 +14.3 +0.1 -40.0 +0.0 2.6 16.1 -13.5 None 5 500.144k 6.8 +12.8 +0.2 +0.0 +0.0 19.8 33.6 -13.8 None 6 749.973k 0.5 +10.7 +0.2 +0.0 +0.0 11.4 30.1 -18.7 None 7 250.144k 24.4 +14.7 +0.1 -40.0 +0.0 -0.8 19.6 -20.4 None Page 20 of 25 Report No: FC99-014A

Test Location: CKC Laboratories, Inc. • 5473A Clouds Rest Rd, Barn • Mariposa, CA 95338 • (800)-500- 4EMC Customer: HID Corporation Date: Feb-18-99 Specification: FCC 15.209 Time: 14:54 Test Type: Maximized Emissions Sequence#: 24 Equipment: Proximity Reader Manufacturer: HID Tested By: Dustin Oaks Model: 5355/8B S/N: N/A Equipment Under Test (* = EUT): Function Manufacturer Model # S/N Proximity Reader* HID 5355/8B N/A Support Devices: Function Manufacturer Model # S/N Power Supply Sorensen DCR60 - 30B 0176 Test Conditions / Notes: EUT operating in normal mode. No Proxcard in field. EUT receiving operating voltage of 24VDC via power supply. Measurement Data: Sorted by Margin Test Distance: 3 Meters Amp Bicon Cable # Freq Rdng Dist Corr Spec Margin Polar MHz dBµV dB dB dB dB dB dBµV/m dBµV/m dB 1 33.940 49.3 -27.3 +12.6 +1.0 +0.0 35.7 40.0 -4.3 Vert Quasi Peak ^ 33.905 54.3 -27.3 +12.6 +1.0 +0.0 40.6 40.0 +0.6 Vert 3 65.072 49.3 -27.2 +8.9 +1.4 +0.0 32.4 40.0 -7.6 Vert Quasi Peak ^ 65.070 51.8 -27.2 +8.9 +1.4 +0.0 34.9 40.0 -5.1 Vert 5 48.063 46.5 -27.2 +11.0 +1.3 +0.0 31.6 40.0 -8.4 Vert Quasi Peak ^ 48.054 50.7 -27.2 +11.0 +1.3 +0.0 35.8 40.0 -4.2 Vert 7 188.025 42.0 -26.8 +16.7 +2.6 +0.0 34.5 43.5 -9.0 Vert 8 192.036 41.4 -26.8 +17.1 +2.6 +0.0 34.3 43.5 -9.2 Vert 9 119.976 45.5 -27.2 +13.8 +2.0 +0.0 34.1 43.5 -9.4 Vert 10 168.043 42.0 -26.9 +14.8 +2.4 +0.0 32.3 43.5 -11.2 Vert 11 180.041 40.4 -26.9 +15.9 +2.5 +0.0 31.9 43.5 -11.6 Vert Page 21 of 25 Report No: FC99-014A

Test Location: CKC Laboratories, Inc. • 5473A Clouds Rest Rd, Barn • Mariposa, CA 95338 • (800)-500- 4EMC Customer: HID Corporation Date: Feb-25-99 Specification: FCC pt 15.207 Time: 10:02 Test Type: Conducted Emissions Sequence#: 40 Equipment: Proximity Reader Manufacturer: HID Tested By: Dustin Oaks Model: 5355/8B S/N: N/A Equipment Under Test (* = EUT): Function Manufacturer Model # S/N Proximity Reader* HID 5355/8B N/A Support Devices: Function Manufacturer Model # S/N Power Supply Topward Electronic 2306 920035 Instruments Test Conditions / Notes: EUT is operating in normal operating mode. No Proxcard located in field. EUT received operating voltage of 24VDC via power supply. Negative power lead from EUT tied to DC power supply chassis ground. Measurement Data: Sorted by Margin Test Lead: Black # Freq Rdng Dist Corr Spec Margin Polar MHz dBµV dB dB dB dB dB dBµV/m dBµV/m dB 1 11.511 35.4 +0.0 35.4 48.0 -12.6 Black 2 16.653 34.8 +0.0 34.8 48.0 -13.2 Black 3 11.640 34.2 +0.0 34.2 48.0 -13.8 Black 4 8.632 33.9 +0.0 33.9 48.0 -14.1 Black 5 17.660 33.8 +0.0 33.8 48.0 -14.2 Black 6 16.139 33.8 +0.0 33.8 48.0 -14.2 Black 7 17.022 33.7 +0.0 33.7 48.0 -14.3 Black 8 16.010 33.7 +0.0 33.7 48.0 -14.3 Black 9 7.009 33.6 +0.0 33.6 48.0 -14.4 Black 10 1.510 33.5 +0.0 33.5 48.0 -14.5 Black Page 22 of 25 Report No: FC99-014A

CKC Laboratories, Inc._. Date: Thy Feb25—1999 Tine: 100230 won: 70946 ECC t5.207 Test Lead: Black Sequencetl 40 dBy. 59697Connected to LISN se 70— sa4 soe— ane4 ane4 2004 1e : : asocne mine toune coutte

Test Location: CKC Laboratories, Inc. • 5473A Clouds Rest Rd, Barn • Mariposa, CA 95338 • (800)-500- 4EMC Customer: HID Corporation Date: Feb-25-99 Specification: FCC pt 15.207 Time: 10:02 Test Type: Conducted Emissions Sequence#: 41 Equipment: Proximity Reader Manufacturer: HID Tested By: Dustin Oaks Model: 5355/8B S/N: N/A Equipment Under Test (* = EUT): Function Manufacturer Model # S/N Proximity Reader* HID 5355/8B N/A Support Devices: Function Manufacturer Model # S/N Power Supply Topward Electronic 2306 920035 Instruments Test Conditions / Notes: EUT is operating in normal operating mode. No Proxcard located in field. EUT received operating voltage of 24VDC via power supply. Negative power lead from EUT tied to DC power supply chassis ground. Measurement Data: Sorted by Margin Test Lead: White # Freq Rdng Dist Corr Spec Margin Polar MHz dBµV dB dB dB dB dB dBµV/m dBµV/m dB 1 16.637 35.6 +0.0 35.6 48.0 -12.4 White 2 15.640 35.0 +0.0 35.0 48.0 -13.0 White 3 15.142 34.2 +0.0 34.2 48.0 -13.8 White 4 17.006 34.1 +0.0 34.1 48.0 -13.9 White 5 15.512 34.1 +0.0 34.1 48.0 -13.9 White 6 8.510 34.1 +0.0 34.1 48.0 -13.9 White 7 13.632 33.9 +0.0 33.9 48.0 -14.1 White 8 12.636 33.9 +0.0 33.9 48.0 -14.1 White 9 1.020 33.8 +0.0 33.8 48.0 -14.2 White 10 9.003 33.6 +0.0 33.6 48.0 -14.4 White Page 24 of 25 Report No: FC99-014A

CKC Laboratories, Inc._. Date: Thu Feb25—1999 Tine: 100217 Won: 70946 ECC t5.207 Test Lead: whie Sequencetl 4t dBy. 59697Connected to LISN se 70— sa4 soe— ane4 aned 2004 1e : : asocne mine toune coutte


Document Created: 2000-09-21 09:46:36
Document Modified: 2000-09-21 09:46:36
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC