User Manual

FCC ID: JQ623X24X

Users Manual

Download: PDF
FCCID_374783

‰ 3110-2305 Prox/Magstripe Reader, Black ‰ 3110-2405 Prox/Magstripe Reader, w/ kypd, Black 1-Instructions 2280-4587 General The Wall Mount Combination Proximity & Magnetic Stripe Card Reader reads the following format cards: Magnetic Stripe: ABA/ANSI/ISO and EMPI Proximity: HID 26-37 bit, EMPI and Proxi 10 The readers are normally wall mounted and designed for indoor or outdoor use. Proximity cards are placed in front of the reader and normally read at a distance of six inches (at +5 VDC) and seven inches (at 12.0 VDC). Mounting the readers on metal will typically reduce the distance. The data is transmitted to any host controller that can supply +5 to +24 VDC operating voltage to the reader, and that can accept the standard Wiegand 26-bit or 34-bit format. Before Installing Figure 1 Reade 1 The host controller must supply +5 to +24 VDC operating 3 For outdoor applications, use a suitable weather-proof back voltage to the reader. The voltage drop as measured box, or handy box, and install the weather seal (provided) on across the reader must be within 5 to 24.0 VDC. the back of the readers' base by pushing it securely and evenly into the "U" shaped recess. See figure 2. 2 The maximum recommended reader distance from the host is: 200 feet with #22 AWG 5 or 6-wire cable 500 feet with #18 AWG 5 or 6-wire cable Unshielded wire is acceptable. Some host controllers may require tighter standards. Mounting 1 The reader is designed to be mounted with the slot facing the floor. The user inserts the card upward into the card insertion slot. 2 The reader can be mounted on a standard single-gang handy box, (the preferred method) or on any firm flat surface. The mounting screws should be firmly tightened, but not excessively. Note that the read head assembly screws are Grasp the lower edge of the reader cover. While applying gentle purposely loose to allow the head to "float"; no adjustments pressure pull the cover away from the base. are necessary. See figure 1. 4 Recommended reader mounting height from the floor is "shoulder height" or about 60 inches. A lower height causes significant user inconvenience. Reader height may be lowered to accommodate ADA requirements. PN: 2280-4587 REV 4 Card Reader kit consists of: 1-Reader assembly 1-Installation Kit 2270-0580

Installation Steps Keypad Data Specifications Returned Material WARNING The model 240 keypad sends data keystroke-by-keystroke to INPUT: Before returning ANY product, you must call the Customer To prevent damage to equipment, make all the host controller in an 8-bit (per keystroke). data format. See Magnetic Stripe: ABA/ANSI/ISO & EMPI Service Department (949) 598-2000, to obtain a Return Material connections with power off. Dorado by HID Application Note 20 for details. Proximity: HID 26 – 37 bit, EMPI & PROXI 10. Authorization (RMA) number. Equipment that fails during normal use within the warranty period (see warranty information) will be repaired or replaced at the discretion of Dorado by HID. Equipment that fails after the warranty period has expired from Diagnostic Tests READING DISTANCE: external sources (such as lightning or abuse) will be repaired at Seven inches typical at 12 VDC (six if mounted on 1 If the reader is to be mounted on a mullion or firm flat Dorado by HID’s current labor rate after a repair estimate has surface, pull an appropriate length and gauge of cable The Model 230 Proximity Card Readers are factory calibrated metal) six inches typical at 5 VDC (five if mounted on been provided. Following agreement by the client as evidence by between the host and mullion. and is not field serviceable. metal) Purchase Order or Credit Card submitted. 2 If the reader is to be mounted on a flat surface rather than a 1 A card with the expected card format will cause the reader DATA OUTPUT: LED to "wink" dark and the buzzer to sound for 0.1 second handy box, use the reader base both as a template to Proximity Data: Output based on card type FCC Notice establish drill locations for suitable molly fasteners, etc. (not while outputting data to the host. Magnetic Stripe Data: Wiegand 26, Wiegand 34 or All provided), and as a guide to remove sufficient material for Bits Wiegand (up to 64 bits) wire clearance. Then pull the appropriate wire between the Proximity Readers (Transmitters) host and reader location. 2 Direct substitution with a known good reader is the best way to isolate the problem. LED CONTROL: Red/Green control with brown wire control line (ground This device complies with part 15 of the FCC rules. Operation is 3. Connect the wires of the pigtail assembly to the cable end at wire) subject to the following two conditions: (1) this device may not cause the reader location. Connections can be crimped or made 3 If the reader is exchanged and the problem still exists, harmful interference, and (2) this device must accept any interference with twist on wire nuts. measure the voltage drop at the reader between the RED received, including interference that may cause undesired operation. (Positive) and the BLACK (Common) wire with the reader connected to the host. It should measure between 5 and WIRE LENGTH: Changes or modifications not expressly approved by the party 24.0 VDC. Low voltage is a common source of problems. 200 feet with #22 AWG wire responsible for compliance could void the user’s authority to operate FUNCTION WIRE COLOR 500 feet with #18 AWG wire the equipment. +5 to 24 VDC RED Green LED BROWN 4 Verify that the card used to test is a known good card, and is Data "1" /Data Output WHITE (HID Readers and others in certain cases where shielded cable is used) authorized in host memory. Verify the reader options are set TEMPERATURE RANGE: For proper regulatory compliance, the drain wire should be Data "0" /Clock Output GREEN correctly for that particular host, and the proper "Comparison COMMON BLACK -35 to +66 degrees Celsius (-31 to 150 degrees disconnected at the power supply end of the cable. Number" or site code has been recorded in host memory. Fahrenheit). Buzzer YELLOW Format Selection Switch (16 position rotary) 5 Verify the wiring, continuity, and connections between reader 1 ABA mag stripe & HID prox to All Bits Wiegand and host. If possible, switch the reader input wiring at the POWER: 2 ABA mag stripe & HID prox to Wiegand 26 bit host to another known good input terminal group. 5 VDC to 24.0 VDC input, 120 mA nominal at +5.0 3 ABA mag stripe & HID prox to Wiegand 34 bit VDC to 170 mA nominal at +12.0 VDC. 4 EMPI mag stripe & EMPI prox to Wiegand 26 bit 5 EMPI mag stripe & EMPI prox to Wiegand 34 bit 6 If the problem still cannot be resolved, contact Dorado by 6 EMPI mag stripe & HID prox to Wiegand 26 bit HID Technical Support, (949) 598-2000. READ SPEED: 7 EMPI mag stripe & HID prox to Wiegand 34 bit Following ABA only ANSI 10 or 12 (5/5 or 6/6) 80 milliseconds 8 ABA mag stripe & Proxi 10 prox to Wiegand 26 bit 9 ABA mag stripe & Proxi 10 prox to Wiegand 34 bit DIMENSIONS: Reader; 4.70" H x 3.00" W x 1.54" D. 4 Connect the other end of the cable to the host controller being sure to follow the appropriate color code and wire lead BUZZER: functions. Activates momentarily upon card acceptance and Keystroke activation or grounding of yellow wire. 5 Verify that the cards to be read are encoded with the selected data format. 6. Observe the reader LED; it should flash green four times as a Warranty Information self-test when first powered on. If this is not the case, or it Dorado by HID warrants to the original purchaser that card continues with short double flashes, a problem exists, refer to readers are free from defects in material and, workmanship the Diagnostic Tests section. under normal use and service for 27 months, from date of original invoice, (control boards only). Normal wear and tear, including magnetic head wear, and damage caused Force Majeure, is excluded from this warranty. Unless otherwise agreed in writing by Dorado by HID, the buyer shall be responsible to assure the proper installation environment is provided, and Dorado by HID assumes no responsibility for malfunctions or damage due to improper installation of products. Dorado by HID’s obligation under this warranty shall be limited to the repair or replacement of any returned product provided that the claim is presented within the time specified above. This warranty is in lieu of all other warranties express or implied, including the warranties of merchantability, or fitness for any particular use. In no event shall Dorado by HID be liable for any breach of warranty in an amount exceeding the net selling price of any defective products.


Document Created: 2003-11-19 15:09:14
Document Modified: 2003-11-19 15:09:14
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC