Test Report

FCC ID: JQ61351B

Test Report

Download: PDF
FCCID_787234

HID GLOBAL CORPORATION TEST REPORT FOR THE 1351 PROXPASS II FCC PART 15 SUBPART C SECTION 15.209 COMPLIANCE DATE OF ISSUE: NOVEMBER 29, 2006 PREPARED FOR: PREPARED BY: HID Global Corporation Mary Ellen Clayton 9292 Jeromino Road CKC Laboratories, Inc. Irvine, CA 92618-1905 5046 Sierra Pines Drive Mariposa, CA 95338 P.O. No.: 11008315 Date of test: November 17-20, 2006 W.O. No.: 85557 Report No.: FC06-074 This report contains a total of 24 pages and may be reproduced in full only. Partial reproduction may only be done with the written consent of CKC Laboratories, Inc. The results in this report apply only to the items tested, as identified herein. Page 1 of 24 Report No.: FC06-074

TABLE OF CONTENTS Administrative Information .............................................................................................3 FCC to Canada Standard Correlation Matrix...................................................................4 Conditions for Compliance ..............................................................................................4 Approvals.........................................................................................................................4 FCC 15.31(e) Voltage Variation......................................................................................5 FCC 15.31(m) Number Of Channels ...............................................................................5 FCC 15.33(a) Frequency Ranges Tested .........................................................................5 FCC 15.35 Analyzer Bandwidth Settings........................................................................5 FCC 15.203 Antenna Requirements ................................................................................5 FCC 15.205 Restricted Bands..........................................................................................5 EUT Operating Frequency...............................................................................................5 Temperature And Humidity During Testing....................................................................5 Equipment Under Test (EUT) Description ......................................................................6 Equipment Under Test .....................................................................................................6 Peripheral Devices ...........................................................................................................6 Report of Measurements ..................................................................................................7 Table 1: FCC 15.209 Carrier Emission Levels....................................................7 Table 2: FCC 15.209 Six Highest Radiated Emission Levels .............................8 Occupied Bandwidth............................................................................................9 EUT Setup........................................................................................................................10 Correction Factors............................................................................................................10 Table A: Sample Calculations .............................................................................10 Test Instrumentation and Analyzer Settings ....................................................................11 Spectrum Analyzer Detector Functions ...............................................................11 Peak..........................................................................................................11 Quasi-Peak ...............................................................................................11 Average ....................................................................................................11 EUT Testing.....................................................................................................................12 Radiated Emissions..............................................................................................12 Appendix A: Test Setup Photographs..............................................................................13 Photograph Showing Radiated Emissions ...........................................................14 Photograph Showing Radiated Emissions ...........................................................15 Photograph Showing Radiated Emissions ...........................................................16 Photograph Showing Radiated Emissions ...........................................................17 Appendix B: Test Equipment List ...................................................................................18 Appendix C: Measurement Data Sheets ..........................................................................19 Page 2 of 24 Report No.: FC06-074

ADMINISTRATIVE INFORMATION DATE OF TEST: November 17-20, 2006 DATE OF RECEIPT: November 17, 2006 MANUFACTURER: HID Global Corporation 9292 Jeromino Road Irvine, CA 92618-1905 REPRESENTATIVE: Frank de Vall TEST LOCATION: CKC Laboratories, Inc. 5046 Sierra Pines Drive Mariposa, CA 95338 TEST METHOD: ANSI C63.4 (2003) PURPOSE OF TEST: To demonstrate the compliance of the 1351 ProxPass II with the requirements for FCC Part 15 Subpart C Section 15.209 devices. Page 3 of 24 Report No.: FC06-074

FCC TO CANADA STANDARD CORRELATION MATRIX Canadian Canadian FCC FCC Test Description Standard Section Standard Section RSS GEN 7.1.4 47CFR 15.203 Antenna Connector Requirements RSS GEN 7.2.1 47CFR 15.35(c) Pulsed Operation RSS GEN 7.2.2 47CFR 15.207 AC Mains Conducted Emissions Requirement RSS 210 2.1 47CFR 15.215(c) Frequency Stability Recommendation RSS 210 2.2 47CFR 15.205 Restricted Bands of Operation RSS 210 2.6 47CFR 15.209 General Radiated Emissions Requirement IC 3082A-1 784962 Site File No. CONDITIONS FOR COMPLIANCE No modifications to the EUT were necessary to comply. Conducted emissions not required for this device because it is battery powered. APPROVALS Steve Behm, Director of Engineering Services QUALITY ASSURANCE: TEST PERSONNEL: Joyce Walker, Quality Assurance Administrative Randy Clark, EMC Engineer Manager Mike Wilkinson, EMC Engineer/Lab Manager Page 4 of 24 Report No.: FC06-074

FCC 15.31(e) Voltage Variations Not applicable to this device because it is battery powered. FCC 15.31(m) Number Of Channels This device operates on a single channel. FCC 15.33(a) Frequency Ranges Tested 15.209 Radiated Emissions: 9 kHz – 1000 MHz FCC SECTION 15.35: ANALYZER BANDWIDTH SETTINGS PER FREQUENCY RANGE TEST BEGINNING FREQUENCY ENDING FREQUENCY BANDWIDTH SETTING RADIATED EMISSIONS 9 kHz 150 kHz 200 Hz RADIATED EMISSIONS 150 kHz 30 MHz 9 kHz RADIATED EMISSIONS 30 MHz 1000 MHz 120 kHz FCC 15.203 Antenna Requirements The antenna is an integral part of the EUT and is non-removable; therefore the EUT complies with Section 15.203 of the FCC rules. FCC 15.205 Restricted Bands The fundamental operating frequency lies outside the restricted bands and therefore complies with the requirements of Section 15.205 of the FCC rules. Any spurious emission coming from the EUT was investigated to determine if any portion lies inside the restricted band. If any portion of a spurious emissions signal was found to be within a restricted band, investigation was performed to ensure compliance with Section 15.209. EUT Operating Frequency The EUT was operating at 139.6 kHz. Temperature And Humidity During Testing The temperature during testing was within +15°C and + 35°C. The relative humidity was between 20% and 75%. Page 5 of 24 Report No.: FC06-074

EQUIPMENT UNDER TEST (EUT) DESCRIPTION The customer declares the EUT tested by CKC Laboratories was representative of a production unit. EQUIPMENT UNDER TEST ProxPass II Manuf: HID Global Corporation Model: 1351 Serial: 111706 FCC ID: JQ61351 PERIPHERAL DEVICES The EUT was not tested with peripheral devices. Page 6 of 24 Report No.: FC06-074

REPORT OF MEASUREMENTS The following tables report the worst case emissions levels recorded during the tests performed on the EUT. All readings taken were peak readings unless otherwise stated. The data sheets from which the emissions tables were compiled are contained in Appendix C. Table 1: FCC 15.209 Carrier Emission Levels METER CORRECTION FACTORS CORRECTED SPEC FREQUENCY READING Cable Ant Corr READING LIMIT MARGIN NOTES MHz dBµV dB dB dB dBµV/m dBµV/m dB 0.138 53.8 0.2 10.1 -80.0 -15.9 24.8 -40.7 V 0.138 53.2 0.2 10.1 -80.0 -16.5 24.8 -41.3 V 0.139 53.0 0.2 10.1 -80.0 -16.7 24.7 -41.4 V 0.139 52.7 0.2 10.1 -80.0 -17.0 24.7 -41.7 V 0.140 53.9 0.2 10.1 -80.0 -15.8 24.7 -40.5 V 0.140 53.6 0.2 10.1 -80.0 -16.1 24.7 -40.8 V Test Method: ANSI C63.4 (2003) NOTES: V = Vertical Polarization Spec Limit: FCC Part 15 Subpart C Section 15.209 Test Distance: 3 Meters COMMENTS: EUT is a hand held card transmitting at 139.6 kHz and is battery operated only. The EUT is transmitting continuously with duty cycle during the test. Fresh batteries were installed prior to test. Test distance correction factor applied in accordance with 15.31 of 40dB per decade to correct test data for comparison to the limit. Measurements were performed over a ground plane. Measurements include peak data for all modulation products within the 20dB bandwidth of the device. EUT Testing in three orthogonal positions, indicated by X, Y and Z notes. No EUT Emissions detected within 40dB of the limit. Frequency Range Investigated: Carrier Upper Sideband (centered on 139 kHz). Temperature: 21.1ºC, Relative Humidity: 32%. Page 7 of 24 Report No.: FC06-074

Table 2: FCC 15.209 Six Highest Radiated Emission Levels METER CORRECTION FACTORS CORRECTED SPEC FREQUENCY READING Cable Ant Corr READING LIMIT MARGIN NOTES MHz dBµV dB dB dB dBµV/m dBµV/m dB 0.110 44.9 0.2 10.3 -40.0 -24.6 26.8 -51.4 V 0.112 44.8 0.2 10.3 -40.0 -24.7 26.6 -51.3 V 0.112 44.3 0.2 10.3 -40.0 -25.2 26.6 -51.8 V 4.000 13.9 0.6 10.0 -40.0 -15.5 29.5 -45.0 H 8.000 8.5 0.8 9.8 -40.0 -20.9 29.5 -50.4 H 16.000 7.2 1.0 9.3 -40.0 -22.5 29.5 -52.0 H Test Method: ANSI C63.4 (2003) NOTES: H = Horizontal Polarization Spec Limit: FCC Part 15 Subpart C Section 15.209 V = Vertical Polarization Test Distance: 3 Meters COMMENTS: EUT is a hand held card transmitting at 139.6 kHz and is battery operated only. The EUT is transmitting continuously with duty cycle during the test. Fresh batteries were installed prior to test. Test distance correction factor applied in accordance with 15.31 of 40dB per decade to correct test data for comparison to the limit. Measurements were performed over a ground plane. Frequency Range Investigated: 9 kHz – 1000 MHz. No EUT emissions detected in the frequency range of 30-1000 MHz. Temperature: 21.1ºC, Relative Humidity: 32%. Page 8 of 24 Report No.: FC06-074

OCCUPIED BANDWIDTH Page 9 of 24 Report No.: FC06-074

EUT SETUP The equipment under test (EUT) was set up in a manner that represented its normal use, as shown in the photographs in Appendix A. Any special conditions required for the EUT to operate normally are identified in the comments that accompany the emissions tables. The corrected data was then compared to the applicable emission limits to determine compliance. The cables were routed consistent with the typical application by varying the configuration of the test sample. Interface cables were connected to the available I/O ports of the test unit. The effect of varying the position of the cables was investigated to find the configuration that produced maximum emissions. I/O cables were of the type and length specified in the individual requirements. The length of cable that produced maximum emissions was selected. The radiated emissions data of the EUT was taken with the HP Spectrum Analyzer. Incorporating the applicable correction factors for distance, antenna, cable loss and amplifier gain, the data was reduced as shown in Table A. Preliminary and final measurements were taken in order to ensure that all emissions from the EUT were found and maximized. CORRECTION FACTORS The basic spectrum analyzer reading was converted using correction factors as shown in the highest emissions readings in the tables. For radiated emissions in dBµV/m, the spectrum analyzer reading in dBµV was corrected by using the following formula in Table A. This reading was then compared to the applicable specification limit to determine compliance. TABLE A: SAMPLE CALCULATIONS Meter reading (dBµV) + Antenna Factor (dB) + Cable Loss (dB) - Distance Correction (dB) - Preamplifier Gain (dB) = Corrected Reading (dBµV/m) Page 10 of 24 Report No.: FC06-074

TEST INSTRUMENTATION AND ANALYZER SETTINGS The test instrumentation and equipment listed in Appendix B were used to collect the radiated emissions data. For radiated measurements from 9 kHz to 30 MHz, the magnetic loop antenna was used. For frequencies from 30 to 1000 MHz, the biconilog antenna was used. The horn antenna was used for frequencies above 1000 MHz. The HP spectrum analyzer was used for all measurements. Table B shows the analyzer bandwidth settings that were used in designated frequency bands. During radiated testing, the measurements were made with 0 dB of attenuation, a reference level of 97 dBµV, and a vertical scale of 10 dB per division. SPECTRUM ANALYZER DETECTOR FUNCTIONS The notes that accompany the measurements contained in the Tables indicate the type of detector function used to obtain the given readings. Unless otherwise noted, all readings were made in the "Peak" mode. Whenever a "Quasi-Peak" or "Average" reading is listed as one of the six highest readings, this is indicated as a "Q" or an "A" in the appropriate table. The following paragraphs describe in more detail the detector functions and when they were used to obtain the emissions data. Peak In this mode, the Spectrum Analyzer or test engineer recorded all emissions at their peak value as the frequency band selected was scanned. By combining this function with another feature of the analyzer called "peak hold," the analyzer had the ability to measure transients or low duty cycle transient emission peak levels. In this mode the analyzer made a slow scan across the frequency band selected and measured the peak emission value found at each frequency across the band. Quasi-Peak When the true peak values exceeded or were within 2 dB of the specification limit, quasi-peak measurements were taken using the HP Quasi-Peak Adapter for the HP Spectrum Analyzer. The detailed procedure for making quasi peak measurements contained in the HP Quasi-Peak Adapter manual were followed. Average For certain frequencies, average measurements may be made using the spectrum analyzer. To make these measurements, the test engineer reduces the video bandwidth on the analyzer until the modulation of the signal is filtered out. At this point the analyzer is set into the linear mode and the scan time is reduced. Page 11 of 24 Report No.: FC06-074

EUT TESTING Radiated Emissions The EUT was mounted on a nonconductive, rotating table 80 cm above the conductive grid. The nonconductive table dimensions were 1 meter by 1.5 meters. During the preliminary radiated scan, the EUT was powered up and operating in its defined FCC test mode. For radiated measurements from 9 kHz to 30 MHz, the magnetic loop antenna was used. The frequency range of 30 MHz to 1000 MHz was scanned with the biconilog antenna located about 1.5 meter above the ground plane in the vertical polarity. During this scan, the turntable was rotated and all peaks at or near the limit were recorded. A scan of the FM band from 88 to 110 MHz was then made using a reduced resolution bandwidth and frequency span. The biconilog antenna was changed to the horizontal polarity and the above steps were repeated. Care was taken to ensure that no frequencies were missed within the FM and TV bands. An analysis was performed to determine if the signals that were at or near the limit were caused by an ambient transmission. If unable to determine by analysis, the equipment was powered down to make the final determination if the EUT was the source of the emission. A thorough scan of all frequencies was made manually using a small frequency span, rotating the turntable and raising and lowering the antenna from one to four meters as needed. The test engineer maximized the readings with respect to the table rotation, antenna height, and configuration of EUT. Maximizing of the EUT was achieved by monitoring the spectrum analyzer on a closed circuit television monitor. Page 12 of 24 Report No.: FC06-074

APPENDIX A TEST SETUP PHOTOGRAPHS Page 13 of 24 Report No.: FC06-074

PHOTOGRAPH SHOWING RADIATED EMISSIONS Radiated Emissions – Test Setup Page 14 of 24 Report No.: FC06-074

PHOTOGRAPH SHOWING RADIATED EMISSIONS Radiated Emissions - X Page 15 of 24 Report No.: FC06-074

PHOTOGRAPH SHOWING RADIATED EMISSIONS Radiated Emissions - Y Page 16 of 24 Report No.: FC06-074

PHOTOGRAPH SHOWING RADIATED EMISSIONS Radiated Emissions - Z Page 17 of 24 Report No.: FC06-074

APPENDIX B TEST EQUIPMENT LIST FCC 15.209 9 kHz – 30 MHz and Carrier Function S/N Calibration Date Cal Due Date Asset # Agilent E4446A SA US44300407 01/12/2005 01/12/2007 02660 EMCO Loop Antenna 1074 05/13/2005 05/13/2007 00226 FCC 15.209 30-1000 MHz Function S/N Calibration Date Cal Due Date Asset # Agilent E4446A SA US44300407 01/12/2005 01/12/2007 02660 Chase CBL6111C Bilog 2456 06/07/2005 06/07/2007 01991 HP 8447D Preamp 1937A02604 03/11/2005 03/11/2007 00099 Page 18 of 24 Report No.: FC06-074

APPENDIX C: MEASUREMENT DATA SHEETS Page 19 of 24 Report No.: FC06-074

Test Location: CKC Laboratories •4933 Sierra Pines Dr. • Mariposa, CA 95338 • 1-800-500-4EMC (4362) Customer: HID Global Specification: FCC 15.209 Work Order #: 85557 Date: 11/20/2006 Test Type: Maximized Emissions Time: 14:13:14 Equipment: ProxPass II Sequence#: 3 Manufacturer: HID Global Tested By: Randal Clark Model: 1351 S/N: 111706 Equipment Under Test (* = EUT): Function Manufacturer Model # S/N ProxPass II* HID Global 1351 111706 Support Devices: Function Manufacturer Model # S/N Test Conditions / Notes: EUT is a hand held card transmitting at 139.6 kHz and is battery operated only. The EUT is transmitting continuously with duty cycle during the test. Fresh batteries were installed prior to test. Test distance correction factor applied in accordance with 15.31 of 40dB per decade to correct test data for comparison to the limit. Measurements were performed over a ground plane. Measurements include peak data for all modulation products within the 20dB bandwidth of the device. EUT Testing in three orthogonal positions, indicated by X, Y and Z notes. No EUT Emissions detected within 40dB of the limit. Frequency Range Investigated: Carrier Upper Sideband (centered on 139 kHz). Temperature: 21.1ºC, Relative Humidity: 32%. Transducer Legend: T1=Cable - Site D 10m 9k-1G T2=Mag Loop - AN 00226 - 9kHz-30M T3=15.31 3m 40dB/Dec Correction Measurement Data: Reading listed by margin. Test Distance: 3 Meters # Freq Rdng T1 T2 T3 Dist Corr Spec Margin Polar MHz dBµV dB dB dB dB Table dBµV/m dBµV/m dB Ant 1 140.316k 53.9 +0.2 +10.1 -80.0 +0.0 -15.8 24.7 -40.5 Verti X 100 2 137.754k 53.8 +0.2 +10.1 -80.0 +0.0 -15.9 24.8 -40.7 Verti X 100 3 140.309k 53.6 +0.2 +10.1 -80.0 +0.0 -16.1 24.7 -40.8 Verti Z 100 4 137.740k 53.2 +0.2 +10.1 -80.0 +0.0 -16.5 24.8 -41.3 Verti Z 100 5 139.042k 53.0 +0.2 +10.1 -80.0 +0.0 -16.7 24.7 -41.4 Verti X 100 6 139.028k 52.7 +0.2 +10.1 -80.0 +0.0 -17.0 24.7 -41.7 Verti Z 100 7 140.295k 49.3 +0.2 +10.1 -80.0 +0.0 -20.4 24.7 -45.1 Horiz X 100 8 137.747k 49.2 +0.2 +10.1 -80.0 +0.0 -20.5 24.8 -45.3 Horiz X 100 9 141.590k 48.7 +0.2 +10.1 -80.0 +0.0 -21.0 24.6 -45.6 Verti X 100 10 141.590k 48.5 +0.2 +10.1 -80.0 +0.0 -21.2 24.6 -45.8 Verti Z 100 Page 20 of 24 Report No.: FC06-074

11 140.309k 48.6 +0.2 +10.1 -80.0 +0.0 -21.1 24.7 -45.8 Horiz Z 100 12 137.754k 48.5 +0.2 +10.1 -80.0 +0.0 -21.2 24.8 -46.0 Horiz Z 100 13 139.042k 48.3 +0.2 +10.1 -80.0 +0.0 -21.4 24.7 -46.1 Horiz X 100 14 139.035k 47.8 +0.2 +10.1 -80.0 +0.0 -21.9 24.7 -46.6 Horiz Z 100 15 136.487k 47.9 +0.2 +10.1 -80.0 +0.0 -21.8 24.9 -46.7 Verti X 100 16 136.494k 47.4 +0.2 +10.1 -80.0 +0.0 -22.3 24.9 -47.2 Verti Z 100 17 141.583k 44.8 +0.2 +10.1 -80.0 +0.0 -24.9 24.6 -49.5 Horiz X 100 18 141.583k 44.2 +0.2 +10.1 -80.0 +0.0 -25.5 24.6 -50.1 Horiz Z 100 19 136.466k 43.8 +0.2 +10.1 -80.0 +0.0 -25.9 24.9 -50.8 Horiz X 100 20 136.480k 43.4 +0.2 +10.1 -80.0 +0.0 -26.3 24.9 -51.2 Horiz Z 100 21 137.740k 40.7 +0.2 +10.1 -80.0 +0.0 -29.0 24.8 -53.8 Verti Y 100 22 140.309k 40.3 +0.2 +10.1 -80.0 +0.0 -29.4 24.7 -54.1 Verti Y 100 23 139.028k 40.0 +0.2 +10.1 -80.0 +0.0 -29.7 24.7 -54.4 Verti Y 100 24 141.597k 36.7 +0.2 +10.1 -80.0 +0.0 -33.0 24.6 -57.6 Verti Y 100 25 136.473k 36.3 +0.2 +10.1 -80.0 +0.0 -33.4 24.9 -58.3 Verti Y 100 26 139.000k 31.6 +0.2 +10.1 -80.0 +0.0 -38.1 24.7 -62.8 Horiz Y - No EUT signals 100 detected in this configuration. Page 21 of 24 Report No.: FC06-074

Test Location: CKC Laboratories •4933 Sierra Pines Dr. • Mariposa, CA 95338 • 1-800-500-4EMC (4362) Customer: HID Global Specification: FCC 15.209 Work Order #: 85557 Date: 11/20/2006 Test Type: Maximized Emissions Time: 12:30:09 Equipment: ProxPass II Sequence#: 2 Manufacturer: HID Global Tested By: Randal Clark Model: 1351 S/N: 111706 Equipment Under Test (* = EUT): Function Manufacturer Model # S/N ProxPass II* HID Global 1351 111706 Support Devices: Function Manufacturer Model # S/N Test Conditions / Notes: EUT is a hand held card transmitting at 139.6 kHz and is battery operated only. The EUT is transmitting continuously with duty cycle during the test. Fresh batteries were installed prior to test. Test distance correction factor applied in accordance with 15.31 of 40dB per decade to correct test data for comparison to the limit. Measurements were performed over a ground plane. Frequency Range Investigated: 9 kHz – 30 MHz Temperature: 21.1ºC, Relative Humidity: 32%. Transducer Legend: T1=Cable - Site D 10m 9k-1G T2=Mag Loop - AN 00226 - 9kHz-30M T3=15.31 3m 40dB/Dec Correction Measurement Data: Reading listed by margin. Test Distance: 3 Meters # Freq Rdng T1 T2 T3 Dist Corr Spec Margin Polar MHz dBµV dB dB dB dB Table dBµV/m dBµV/m dB Ant 1 4.000M 13.9 +0.6 +10.0 -40.0 +0.0 -15.5 29.5 -45.0 Horiz 2 8.000M 8.5 +0.8 +9.8 -40.0 +0.0 -20.9 29.5 -50.4 Horiz 3 112.225k 44.8 +0.2 +10.3 -80.0 +0.0 -24.7 26.6 -51.3 Verti X 4 109.695k 44.9 +0.2 +10.3 -80.0 +0.0 -24.6 26.8 -51.4 Verti Z 5 112.245k 44.3 +0.2 +10.3 -80.0 +0.0 -25.2 26.6 -51.8 Verti Z 6 16.000M 7.2 +1.0 +9.3 -40.0 +0.0 -22.5 29.5 -52.0 Horiz 7 12.000M 6.7 +1.0 +9.7 -40.0 +0.0 -22.6 29.5 -52.1 Horiz 8 109.685k 43.8 +0.2 +10.3 -80.0 +0.0 -25.7 26.8 -52.5 Verti X Page 22 of 24 Report No.: FC06-074

9 110.970k 43.7 +0.2 +10.3 -80.0 +0.0 -25.8 26.7 -52.5 Verti Z 10 110.965k 43.4 +0.2 +10.3 -80.0 +0.0 -26.1 26.7 -52.8 Verti X 11 113.520k 40.4 +0.2 +10.3 -80.0 +0.0 -29.1 26.5 -55.6 Verti X 12 125.000k 29.7 +0.2 +10.2 -80.0 +0.0 -39.9 25.7 -65.6 Verti Z Page 23 of 24 Report No.: FC06-074

Test Location: CKC Laboratories •4933 Sierra Pines Dr. • Mariposa, CA 95338 • 1-800-500-4EMC (4362) Customer: HID Global Specification: FCC 15.209 Work Order #: 85557 Date: 11/20/2006 Test Type: Maximized Emissions Time: 15:44:43 Equipment: ProxPass II Sequence#: 8 Manufacturer: HID Global Tested By: Randal Clark Model: 1351 S/N: 111706 Equipment Under Test (* = EUT): Function Manufacturer Model # S/N ProxPass II* HID Global 1351 111706 Support Devices: Function Manufacturer Model # S/N Test Conditions / Notes: EUT is a hand held card transmitting at 139.6 kHz and is battery operated only. The EUT is transmitting continuously with duty cycle during the test. Fresh batteries were installed prior to test. No EUT emissions detected in this frequency range. Frequency Range Investigated: 30-1000 MHz. Temperature: 21.1ºC, Relative Humidity: 32%. Transducer Legend: Measurement Data: Reading listed by margin. Test Distance: 3 Meters # Freq Rdng Dist Corr Spec Margin Polar MHz dBµV dB dB dB dB Table dBµV/m dBµV/m dB Ant Page 24 of 24 Report No.: FC06-074


Document Created: 2006-12-01 15:38:57
Document Modified: 2006-12-01 15:38:57
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC