Test Report

FCC ID: JQ6-SMARTTRANS2

Test Report

Download: PDF
FCCID_945435

Testing and certification of, consultancy and research concerning, electronic and electric appliances, systems, installations and telecommunication systems TEST REPORT CONCERNING THE COMPLIANCE OF A PROXIMITY CARD READER, OPERATING ON 125 KHZ, 138 KHZ and 13.56 MHZ, BRAND HID, MODELS 814xD INCORPORATING THE SMARTREADERII V01.03 & SMARTEXTENSION/PSK V01.00 47 CFR PART 15 (OCTOBER 07, 2007). THE REQUIREMENTS OF INDUSTRY CANADA: RSS-GEN AND RSS-210 (ISSUE 7, JUNE 2007) FCC listed : 90828 Industry Canada : IC3501A VCCI Registered : R-1518, C-1598 R&TTE, LVD, EMC Notified Body : 1856 TÜV Rheinland EPS B.V. P.O. Box 15 9822 ZG Niekerk (NL) Smidshornerweg 18 9822 TL Niekerk (NL) Telephone: +31 594 505005 Telefax: +31 594 504804 E-mail: info@tuv-eps.com Web: www.tuv-eps.com Project number: 08031403.fcc.smartreader Page 1 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 MEASUREMENT/TECHNICAL REPORT HID Global Corporation Model Summary: This report covers only 1 of 2 transmitter models – the applicant states: differences are explained within the HID Attestation of Similarity found in Appendix 1. All models incorporate the identical circuitry and integral RF Section and PWB embedded antenna housed on the SmartReaderII V01.03 PWA. Prescans were completed on all product geometric differences and the worst case unit was tested and shown in this report. Specific notes have been inserted in each section of this report to better clarify the data shown and its applicability to all units covered. Refer to Appendix 1 for more information. FCC ID: JQ6 – SmartTRANS2 & IC ID: 2236B-SmartTRANS2 May 05, 2008 This report concerns: Original grant/certification Class 2 change Verification Equipment type: 125 kHz, 138 kHz and 13.56 MHz Inductive Proximity Card Reader Deferred grant requested per 47 CFR 0.457(d)(1)(ii) ? Yes No n.a. Report prepared by: Name : Richard van der Meer Company name : TÜV Rheinland EPS B.V. Address : Smidshornerweg 18 Postal code/city : 9822 ZG Niekerk Mailing address : P.O. Box 15 Postal code/city : 9822 TL Niekerk Country : The Netherlands Telephone number : + 31 594 505 005 Telefax number : + 31 594 504 804 E-mail : info@tuv-eps.com The data taken for this test and report herein was done in accordance with 47 CFR Part 15 (October 07, 2007), RSS-GEN AND RSS-210 and the measurement procedures of ANSI C63.4-2003. TÜV Rheinland EPS B.V. at Niekerk, The Netherlands, certifies that the data is accurate and contains a true representation of the emission profile of the Equipment Under Test (EUT) on the date of the test as noted in the test report. I have reviewed the test report and find it to be an accurate description of the test(s) performed and the EUT so tested. Date: May 08, 2008 Signature: H.J. Pieters Project Manager TÜV Rheinland EPS B.V. Project number : 08031403.fcc.smartreader Page 2 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 Description of test item Test item : Proximity Card Reader, operating on 125kHz, 138 kHz and 13.56 MHz, brand HID, model 814xD (Mullion Reader w/ Keypad) Manufacturer : HID Global Corporation Brand : HID Model(s) : 814xD incorporating the SmartReaderII V01.03 Main PWA Serial number(s) : n.a. Revision : n.a. Receipt date : March 14, 2008 Applicant information Applicant's representative : Mr. T. Seeley (USA - Denver, CO Compliance) Company : HID Global Corporation Address : 9292 Jeromino Road Postal code : 92618-1905 City : Irving, CA Country : USA Telephone number : 1+ 949 598 1600 (Main Office), 303-404-6700 (Denver, CO) Telefax number : 1+ 949 598 1680 (Main Office) Test(s) performed Location : Niekerk Test(s) started : April 15, 2008 Test(s) completed : April 29, 2008 Purpose of test(s) : Equipment Authorization (Original grant/certification) Test specification(s) : 47 CFR Part 15 (October 07, 2007), RSS-GEN AND RSS-210 (ISSUE 7, JUNE 2007) R. van der Meer Test engineers : Report written by : R. van der Meer Report date : May 08, 2008 This report is in conformity with NEN-EN-ISO/IEC 17025: 2005 This report shall not be reproduced, except in full, without the written permission of TÜV Rheinland EPS B.V. The test results relate only to the item(s) tested. Project number : 08031403.fcc.smartreader Page 3 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 Table of contents 1 General information. .......................................................................................................................................... 5 1.1 Product description. .................................................................................................................................... 5 1.1.1 Introduction.......................................................................................................................................... 5 1.2 Related submittal(s) and/or Grant(s)........................................................................................................... 5 1.2.1 General................................................................................................................................................ 5 1.2.2 FCC ID JQ6-SmartTRANS2 ................................................................................................................ 5 1.3 Tested system details. ................................................................................................................................ 5 1.3.1 Description of input and output ports. .................................................................................................. 6 1.4 Test methodology. ...................................................................................................................................... 6 1.5 Test facility.................................................................................................................................................. 6 1.6 Test conditions. .......................................................................................................................................... 6 1.7 Justification................................................................................................................................................. 7 1.8 EUT mode of operation............................................................................................................................... 7 1.9 Special accessories. ................................................................................................................................... 7 1.10 Equipment modifications. ........................................................................................................................ 7 1.11 Product Labelling .................................................................................................................................... 7 1.12 Block diagram of the EUT. ...................................................................................................................... 7 1.13 Schematics of the EUT. .......................................................................................................................... 7 1.14 Part list of the EUT. ................................................................................................................................. 7 2 Radiated emission data. .................................................................................................................................... 8 2.1 Radiated field strength measurements ( 30 MHz – 1 GHz, E-field) for 125 kHz option ............................... 8 2.1.1 Radiated field strength measurements ( 30 MHz – 1 GHz, E-field) for 138 kHz option ........................ 9 2.2 Radiated field strength measurements (frequency range of 0.009-30 MHz, H-field) for 125 kHz option. .. 11 2.2.1 Radiated field strength measurements (frequency range of 0.009-30 MHz, H-field) for 138 kHz option ..... 12 3 Carrier stability under special conditions.......................................................................................................... 14 3.1 Frequency stability (on 13.56 MHz) in accordance with 47 CFR Part 15, section 15.225 (e) & RSS-210, section 6.2.2 (e):.................................................................................................................................................. 14 3.1.1 At 85% and 115% of rated voltage supply level................................................................................. 14 3.2 Bandwidth of the emission on 13.56 MHz in accordance with RSS-210, section 6.2.2 (e)........................ 14 3.3 Amplitude stability on 13.56 MHz in accordance with RSS-210. ............................................................... 15 3.4 Frequency stability (on 125 kHz) in accordance with 47 CFR Part 15, section 15.225 (e) & RSS-210, section 6.2.2 (e):.................................................................................................................................................. 17 3.4.1 At 85% and 115% of rated voltage supply level................................................................................. 17 3.5 Bandwidth of the emission on 125 kHz in accordance with RSS-210, section 6.2.2 (e)............................ 17 3.6 Amplitude stability on 125 kHz in accordance with RSS-210. ................................................................... 18 3.7 Frequency stability (on 138 kHz) in accordance with 47 CFR Part 15, section 15.225 (e) & RSS-210, section 6.2.2 (e):.................................................................................................................................................. 20 3.7.1 At 85% and 115% of rated voltage supply level................................................................................. 20 3.8 Bandwidth of the emission on 138 kHz in accordance with RSS-210, section 6.2.2 (e)............................ 20 3.9 Amplitude stability on 138 kHz in accordance with RSS-210. ................................................................... 21 4 Conducted emission data. ............................................................................................................................... 24 4.1 Conducted emission data of the EUT (125 kHz and 13.56MHz version) .................................................. 24 4.2 Conducted emission data of the EUT (138 kHz and 13.56 MHz version) ................................................. 25 5 List of utilized test equipment........................................................................................................................... 27 Project number : 08031403.fcc.smartreader Page 4 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 1 General information. 1.1 Product description. 1.1.1 Introduction. The EUT is an inductive proximity card reader intended to be used in access control systems, parking systems and other applications using RFID readers. It is capable of reading 125 kHz, 138 kHz and 13.56 MHz inductive tags. In the case of this test report – 1 of 2 different models is covered. The applicant states that the tested model is representative for the other model as noted in the AoS, but it’s outside the scope of TÜV Rheinland EPS B.V. to have any judgement on this. Prescans were completed and the worst case model tested – there are additional notes in each section to further clarify the applicability of the testing data shown to each of the covered models. The content of this report and measurement results have not been changed other than the way of presenting the data. 1.2 Related submittal(s) and/or Grant(s). 1.2.1 General. This test report supports the original grant/certification in equipment authorization files under FCC ID: JQ6-SmarTRANS2 and 2236B-SmartID. 1.2.2 FCC ID JQ6-SmartTRANS2 This report supports the results of the 125 kHz, 138 kHz and 13.56 MHz Inductive Card Reader (FCC ID: JQ6-SmartTRANS2). 1.3 Tested system details. Details and an overview of the system and all of its components, as it has been tested, may be found below. EUT : Inductive proximity card reader operating at 125 kHz, 138 kHz and 13.56MHz Manufacturer : HID Global Corporation. Brand : HID Model : 8141D (Mullion Reader with Keypad) was found to be the worst case model Serial number : n.a. Voltage input rating : +5 - +24 VDC (any DC power supply) Current input rating : not provided Antenna : Integral to the SmartReaderII V01.03 PWA Remarks : The EUT contains a SmartreaderII/8pin V01.03 with a SmartExtension/PSK V01.00 Board off the back (encapsulated in the potting and a passive keypad over laying the main board on the front outside of the plastic housing Auxiliary equipment 1 : Linear AC/DC Power Supply Manufacturer : Topward electric instruments Co.,LTD. Brand : Topward electric instruments Co.,LTD. Model : TPS-2000 Serial number : 920035 Voltage input rating : 100-120V ~ 50-60Hz Current input rating : -- Voltage output rating : 0-30 Vdc Current output rating : 0-6.4A Remarks : - Project number : 08031403.fcc.smartreader Page 5 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 1.3.1 Description of input and output ports. Number Ports From To Shielding Remarks 1 AC mains AC mains AE1 yes / no None 2 DC power input port AE1 EUT yes / no None 3 Serial port EUT -- yes / no None AE = Auxiliary equipment 1.4 Test methodology. The test methodology used is based on the requirements of 47 CFR Part 15 (October 07, 2007), sections 15.207, 15.209 and 15.225. The test methods, which have been used, are based on ANSI C63.4: 2003. Radiated emission tests above 30 MHz were performed at a measurement distance of 3 meters. Radiated emission tests below 30 MHz were performed at a measurement distance of 3 meters and 10 meters. To calculate the field strength level from these results to the appropriate distance at which the limit is specified, the distance extrapolation factor of 40dB/decade is used. The receivers are switching automatically to the right bandwidth in accordance with CISPR 16. This is implemented in the receiver. The antenna factors are programmed in the test receiver. The receiver automatically calculates the appropriate correction factor for the utilized antenna and also the appropriate antenna factor for the cable loss. The total correction is automatically added to the measured value. 1.5 Test facility. The Federal Communications Commission and Industry Canada has reviewed the technical characteristics of the test facilities at TÜV Rheinland EPS B.V., located in Niekerk, 9822 TL Smidshornerweg 18, The Netherlands, and has found these test facilities to be in compliance with the requirements of 47 CFR Part 15, section 2.948, per October 23, 2000. The description of the test facilities has been filed at the Office of the Federal Communications Commission under registration number 90828. The facility has been added to the list of laboratories performing these test services for the public on a fee basis. The description of the test facilities has been filed to Industry Canada under registration number IC 3501A-1. The facility has been added to the list of laboratories performing these test services for the public on a fee basis. 1.6 Test conditions. Normal test conditions: Temperature (*) : +15°C to +35°C Relative humidity(*) : 20 % to 75 % Supply voltage : 110VAC/60Hz to the AC/DC Power Supply – the DC output was varied across the voltage range specified by the manufacturer Air pressure : 950 – 1050 hPa * When is was impracticable to carry out the tests under these conditions, a note to this effect stating the ambient temperature and relative humidity during the tests are stated separately. Project number : 08031403.fcc.smartreader Page 6 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 System test configuration. 1.7 Justification. The system was configured for testing in a typical fashion (as a customer would normally use it). The justification and manipulation of cables and equipment in order to simulate a worst-case behavior of the test setup has been carried out as prescribed in ANSI C63.4: 2003. 1.8 EUT mode of operation. The EUT has been tested in active mode, i.e. the EUT is ready to detect a card. To assess the behavior of the EUT while reading the card, the EUT is tested with a card presented such that it continuously reads the card, and continuously sends data to the serial port of the EUT. The intentional radiator tests (47 CFR Part 15 sections, 15.207, 15.209 and 15.225) have been performed with a complete functioning EUT and interconnections. 1.9 Special accessories. No special accessories are used and/or needed to achieve compliance. 1.10 Equipment modifications. No modifications have been made to the equipment in order to achieve compliance. Only for the Conducted Emissions testing (section 4) test, the test unit was modified to add a resistive termination in lieu of the antenna. Pictures are available to show the modifications. For all other tests no modifications have been made to the equipment. 1.11 Product Labelling The product labeling information is available in the technical documentation package. 1.12 Block diagram of the EUT. The block diagram is available in the technical documentation package. 1.13 Schematics of the EUT. The schematics are available in the technical documentation package. 1.14 Part list of the EUT. The part list is available in the technical documentation package. Project number : 08031403.fcc.smartreader Page 7 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 2 Radiated emission data. 2.1 Radiated field strength measurements ( 30 MHz – 1 GHz, E-field) for 125 kHz option Measurement results dB(µV)/m @ 3 metres Limits Result Frequency Quasi-peak dB(µV)/m @ 3 metres (MHz) Quasi-peak Vertical Horizontal PASS/FAIL 30.0-88.0 <25 <25 40.0 PASS 88.0-216.0 <25 <25 43.5 PASS except for: 180.820 27.2 25.2 43.5 PASS 205.795 27.4 26.4 43.5 PASS 216.0-950.0 <25 <25 46.0 PASS except for: 217.00 24.9 30.9 46.0 PASS 220.80 29.0 28.0 > 950.0 <25 <25 54.0 PASS Table 1 Radiated emissions of the EUT. The results of the radiated emission tests, carried out in accordance with 47 CFR Part 15 section 15.209 & RSS-210, section 7.2.1 and 7.2.2, with the EUT operating in active mode on 125 kHz and 13.562 MHz while detecting a card are depicted in table 1. Notes: 1. Field strength values of radiated emissions at frequencies not listed in the table above are more than 20 dB below the applicable limit. 2. “<<” means that measurement values are much lower than the value determined for the other polarization. 3. The test data shown above is of the worst case EUT (8141D). 4. Measurement uncertainty is ±5.0dB 5. Taking into account the worst case measurement uncertainty, that would be +5dB, the tested item still passed the test. 6. 13.56MHz Always Active – the “option” of 125kHz or 138kHz is controlled via software at the factory. (HID Statement). Test engineer Signature : Name : Richard van der Meer Date : April 28 , 2008 Project number : 08031403.fcc.smartreader Page 8 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 2.1.1 Radiated field strength measurements ( 30 MHz – 1 GHz, E-field) for 138 kHz option Measurement results dB(µV)/m @ 3 metres Limits Result Frequency Quasi-peak dB(µV)/m @ 3 metres (MHz) Quasi-peak Vertical Horizontal PASS/FAIL 30.0-88.0 <25 <25 40.0 PASS 88.0-216.0 <25 <25 43.5 PASS except for: 180.820 26.2 25.2 43.5 PASS 205.795 26.9 25.4 43.5 PASS 216.0-950.0 <25 <25 46.0 PASS except for: 217.00 24.7 30.6 46.0 PASS 220.780 28.6 26.0 46.0 PASS > 950.0 <25 <25 54.0 PASS Table 2 Radiated emissions of the EUT. The results of the radiated emission tests, carried out in accordance with 47 CFR Part 15 section 15.209 & RSS-210, section 7.2.1 and 7.2.2, with the EUT operating in active mode on 138 kHz and 13.562 MHz while detecting a card are depicted in table 1. Notes: 1. Field strength values of radiated emissions at frequencies not listed in the table above are more than 20 dB below the applicable limit. 2. “<<” means that measurement values are much lower than the value determined for the other polarization. 3. The test data shown above is of the worst case EUT (8141D). 4. Measurement uncertainty is ±5.0dB 5. Taking into account the worst case measurement uncertainty ,that would be +5dB, the tested item still passed the test. 6. Tests carried out at a lower temperature, which was +13°C, than the normal test condition but it is considered as of no consequence taking in to account that both EUT and test equipment used are specified to operate in a wide temperature range that exceeds 7. 13.56MHz Always Active – the “option” of 125kHz or 138kHz is controlled via software at the factory. (HID Statement). Test engineer Signature : Name : Richard van der Meer Date : April 16, 2008 Project number : 08031403.fcc.smartreader Page 9 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 E-field Radiated Emissions Test Setup Photos: 8141D Shown in Setup Photos Project number : 08031403.fcc.smartreader Page 10 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 2.2 Radiated field strength measurements (frequency range of 0.009-30 MHz, H-field) for 125 kHz option. Measurement Limits Measurement results results Part 15.209 Frequency dBµV Antenna factor Cable loss dB(µV)/m & Part 15.225 (MHz) for 30 m dB(µV)/m (calculated) 3 meters 10 meters dB dB 0.009 - 0.490 56.0 27.0 20.1 1 -2.9 (@300m) 48.5 – 13.8 (300 m) 0.490 - 1.705 34.2 n.i. 20.1 1 15.3 33.8 - 22.9 (30 m) 1.705 – 30.0 <25 n.i. 20.1 1 6.1 29.5 (30 m) 13.56 45.1 15 19.6 1 25.7 84.0 (30m) (FCC 15.225-(a) Table 3 Radiated emissions of the EUT. The results of the radiated emission tests, carried out in accordance with 47 CFR Part 15 sections 15.205, 15.209 and 15.225 and RSS-210, section 7.2.1 and 7.2.2 with the EUT operating in continuous transmit mode on 125 kHz and 13.56 MHz, are depicted in table 2. Notes: 1. Calculated measurement results are obtained by using the distance extrapolation factor of 40dB/decade, antenna factor and cable loss. For example: at 13.56 MHz: 45.1 + 19.6 + 1 – 40 = 25.7 dB(µV)/m 2. Frequency range: a. 9- 90 kHz Average detector used during measurements b. 110-490 kHz Average detector used during measurements 3. n.i. Indicates that no field strength values could be measured on the listed frequencies or in the listed frequency range. 4. Field strength values of radiated emissions at frequencies not listed in table 3 are more than 20 dB below the applicable limit 5. The EUT was varied in three positions, the loop antenna was varied in horizontal and vertical orientations and also around it’s axis. The reported value is the worst case found at the reported frequency. 6. The EUT was tested in both normal mode (i.e. without a label in its proximity) and in activated mode (i.e. with a label in its proximity. 7. The test data shown above is of the worst case EUT (8141D). 8. Measurement uncertainty is ±5.0dB 9. Taking into account the worst case measurement uncertainty, that would be +5dB, the tested item still passed the test. Test engineer Signature : Name : R. van der Meer Date : April 28, 2008 Project number : 08031403.fcc.smartreader Page 11 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 2.2.1 Radiated field strength measurements (frequency range of 0.009-30 MHz, H-field) for 138 kHz option Measurement Limits Measurement results results Part 15.209 Frequency dBµV Antenna factor Cable loss dB(µV)/m & Part 15.225 (MHz) for 30 m dB(µV)/m (calculated) 3 meters 10 meters dB dB 0.009 - 0.490 55 n.i. 20.0 1 -4 48.5 – 13.8 (300 m) 0.490 - 1.705 <20 n.i. 20.0 1 n.i. 33.8 - 22.9 (30 m) 1.705 – 30.0 <15 n.i. 20.0 1 n.i. 29.5 (30 m) 13.56 43 24 19.6 1 23.6 84.0 (30m) (FCC 15.225-(a) Table 4 Radiated emissions of the EUT. The results of the radiated emission tests, carried out in accordance with 47 CFR Part 15 sections 15.205, 15.209 and 15.225 and RSS-210, section 7.2.1 and 7.2.2 with the EUT operating in continuous transmit mode on 138 kHz and 13.56 MHz, are depicted in table 2. Notes: 1. Calculated measurement results are obtained by using the distance extrapolation factor of 40dB/decade, antenna factor and cable loss. For example: at 13.56 MHz: 43 + 19.6 + 1 – 40 = 24 dB(µV)/m 2. Frequency range: a. 9- 90 kHz Average detector used during measurements b. 110-490 kHz Average detector used during measurements 3. n.i. Indicates that no field strength values could be measured on the listed frequencies or in the listed frequency range. 4. Field strength values of radiated emissions at frequencies not listed in table 3 are more than 20 dB below the applicable limit 5. The EUT was varied in three positions, the loop antenna was varied in horizontal and vertical orientations and also around it’s axis. The reported value is the worst case found at the reported frequency. 6. The EUT was tested in both normal mode (i.e. without a label in its proximity) and in activated mode (i.e. with a label in its proximity. 7. The test data shown above is of the worst case EUT (8141D). 8. Measurement uncertainty is ±5.0dB 9. Taking into account the worst case measurement uncertainty ,that would be +5dB, the tested item still passed the test. 10. Tests carried out at a lower temperature, which was +13°C, than the normal test condition but it is considered as of no consequence taking in to account that both EUT and test equipment used are specified to operate in a wide temperature range. Test engineer Signature : Name : R. van der Meer Date : April 16, 2008 Project number : 08031403.fcc.smartreader Page 12 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 H-Field Radiated Emissions Test Setup Photos: 8141D Shown in Setup Photos Project number : 08031403.fcc.smartreader Page 13 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 3 Carrier stability under special conditions. 3.1 Frequency stability (on 13.56 MHz) in accordance with 47 CFR Part 15, section 15.225 (e) & RSS-210, section 7.2.6 (e): 1) The frequency tolerance of the carrier signal shall be maintained within +/- 0.01% of the operating frequency over a temperature variation of –20 oC to +50 oC at normal supply voltage (see table 3). Stability under Frequency deviation special Measured frequency (limit +0.01%) PASS/FAIL conditions (MHz) o (%) Temperature ( C) 13.56207 20.0 N.A. N.A. (reference) -20.0 13.56210 < 0.01 PASS 50.0 13.56200 < 0.01 PASS Table 3. 3.1.1 At 85% and 115% of rated voltage supply level The frequency tolerance of the carrier signal shall be maintained within +/- 0.01% of the operating frequency at 85% and at 115% of the rated power supply voltage at 20 oC environmental temperature. The results are stated in Table 4. Stability under Frequency deviation special Measured frequency (limit +0.01%) PASS/FAIL conditions (MHz) (%) % variation U 100.0 13.56207 (reference) N.A. N.A. 85.0 13.56210 < 0.01 PASS 115.0 13.56200 < 0.01 PASS Table 4 3.2 Bandwidth of the emission on 13.56 MHz in accordance with RSS-210, section 7.2.6 (e). Limit: 20 dB of the bandwidth of the emission shall be within the specified frequency band. Bandwidth of the emission is determined at the points 20 dB down from the modulated carrier. Specified frequency band: 13553 kHz - 13567 kHz. Temperature Minimum frequency Maximum frequency o ( C) (kHz) (kHz) +20.0 13562.07 13562.07 -20.0 13562.10 13562.10 +50.0 13562.00 13562.00 Bandwidth 13562.00 13562.10 Table 11 Bandwidth of the emission at 13562kHz. The measured minimum frequency of 13562.00 kHz and maximum frequency of 13562.10 kHz are well within the specified frequency bandwidth. Project number : 08031403.fcc.smartreader Page 14 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 3.3 Amplitude stability on 13.56 MHz in accordance with RSS-210. No particular requirements other than in section 3 of this report. From measurements performed as indicated below, the amplitude stability will not cause non-compliant situations with respect to exclusion bands or emissions outside permissible bands (band edges) Stability under special Amplitude deviation conditions (dB) Supply Voltage (Vdc) 12 (100%) N.A. 5 (-15%) -0.28 24 (+15%) -0.42 Table18 Amplitude stability of the EUT due to voltage variations. Note (Section 2.2.1 through 2.2.3): The applicant wants to state: Since both models incorporated the SmartReaderII V01.03 Main PWA and housed in a plastic enclosure that does not provide different insulative properties to the products – the carrier stability testing was completed on a potted 8141D only and is representative of all models. Test engineer Signature : Name : R. van der Meer Date : April 24, 2008 Project number : 08031403.fcc.smartreader Page 15 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 Carrier Bandwidth/Occupied Bandwidth: Plot 1 –Bandwidth of the emission at 13562 kHz (Fundamental Carrier), for IC the measured Occupied Bandwidth is 100Hz Project number : 08031403.fcc.smartreader Page 16 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 3.4 Frequency stability (on 125 kHz) in accordance with 47 CFR Part 15, section 15.225 (e) & RSS-210, section 7.2.2 (e): 1) The frequency tolerance of the carrier signal shall be maintained within +/- 0.01% of the operating frequency over a temperature variation of –20 oC to +50 oC at normal supply voltage (see table 3). Stability under Frequency deviation special Measured frequency (limit +0.01%) PASS/FAIL conditions (kHz) o (%) Temperature ( C) 124.984 20.0 N.A. N.A. (reference) -20.0 124.920 < 0.01 PASS 50.0 124.990 < 0.01 PASS Table 3. 3.4.1 At 85% and 115% of rated voltage supply level The frequency tolerance of the carrier signal shall be maintained within +/- 0.01% of the operating frequency at 85% and at 115% of the rated power supply voltage at 20 oC environmental temperature. The results are stated in Table 4. Stability under Frequency deviation special Measured frequency (limit +0.01%) PASS/FAIL conditions (kHz) (%) % variation U 100.0 124.984 N.A. N.A. (reference) 85.0 124.980 < 0.01 PASS 115.0 124.980 < 0.01 PASS Table 4 3.5 Bandwidth of the emission on 125 kHz in accordance with RSS-210, section 7.2.2 (e). Limit: 20 dB of the bandwidth of the emission shall be within the specified frequency band. Bandwidth of the emission is determined at the points 20 dB down from the modulated carrier. Specified frequency band: 119 kHz - 135 kHz. Temperature Minimum frequency Maximum frequency o ( C) (kHz) (kHz) +20.0 124.984 124.980 -20.0 124.920 124.980 +50.0 124.990 124.980 Bandwidth 124.920 124.990 Table 11 Bandwidth of the emission at 125 kHz. The measured minimum frequency of 124.920 kHz and maximum frequency of 124.990 kHz are well within the specified frequency bandwidth. Project number : 08031403.fcc.smartreader Page 17 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 3.6 Amplitude stability on 125 kHz in accordance with RSS-210. No particular requirements other than in section 3 of this report. From measurements performed as indicated below, the amplitude stability will not cause non-compliant situations with respect to exclusion bands or emissions outside permissible bands (band edges) Stability under special Amplitude deviation conditions (dB) Supply Voltage (Vdc) 12 (100%) N.A. 5 (-15%) 124.980 24 (+15%) 124.980 Table18 Amplitude stability of the EUT due to voltage variations. Note (Section 2.2.1 through 2.2.3): The applicant wants to state: Since both models incorporated the SmartReaderII V01.03 Main PWA and housed in a plastic enclosure that does not provide different insulative properties to the products – the carrier stability testing was completed on a potted 8141D only and is representative of all models. Test engineer Signature : Name : R. van der Meer Date : April 29, 2008 Project number : 08031403.fcc.smartreader Page 18 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 Plot 2 –Bandwidth of the emission at 125 kHz (Fundamental Carrier), for IC the measured Occupied Bandwidth is 70 Hz * RBW 300 Hz Marker 1 [T1 ] 28.Apr 08 17:16 VBW 1 kHz -5.08 dBm Ref -0.6 dBm * Att 20 dB SWT 180 ms 124.984000000 kHz Offset 19.4 dB 1 -10 A 1 PK VIEW -20 LVL -30 -40 -50 -60 -70 -80 -90 -100 Center 127 kHz 1.6 kHz/ Span 16 kHz Date: 28.APR.2008 17:16:13 Project number : 08031403.fcc.smartreader Page 19 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 3.7 Frequency stability (on 138 kHz) in accordance with 47 CFR Part 15, section 15.225 (e) & RSS-210, section 7.2.2 (e): 1) The frequency tolerance of the carrier signal shall be maintained within +/- 0.01% of the operating frequency over a temperature variation of –20 oC to +50 oC at normal supply voltage (see table 3). Stability under Frequency deviation special Measured frequency (limit +0.01%) PASS/FAIL conditions (kHz) o (%) Temperature ( C) 138.762 20.0 N.A. N.A. (reference) -20.0 138.762 < 0.01 PASS 50.0 138.800 < 0.01 PASS Table 3. 3.7.1 At 85% and 115% of rated voltage supply level The frequency tolerance of the carrier signal shall be maintained within +/- 0.01% of the operating frequency at o 85% and at 115% of the rated power supply voltage at 20 C environmental temperature. The results are stated in Table 4. Stability under Frequency deviation special Measured frequency (limit +0.01%) PASS/FAIL conditions (kHz) (%) % variation U 100.0 138.762 N.A. N.A. (reference) 85.0 138.837 < 0.01 PASS 115.0 138.800 < 0.01 PASS Table 4 3.8 Bandwidth of the emission on 138 kHz in accordance with RSS-210, section 7.2.2 (e). Limit: 20 dB of the bandwidth of the emission shall be within the specified frequency band. Bandwidth of the emission is determined at the points 20 dB down from the modulated carrier. Specified frequency band: 135 kHz - 140 kHz. Temperature Minimum frequency Maximum frequency o ( C) (kHz) (kHz) +20.0 138.762 138.762 -20.0 138.762 138.762 +50.0 138.800 138.837 Bandwidth 138.762 138.837 Table 11 Bandwidth of the emission at 138 kHz. The measured minimum frequency of 138.762 kHz and maximum frequency of 138.837 kHz are well within the specified frequency bandwidth. Project number : 08031403.fcc.smartreader Page 20 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 3.9 Amplitude stability on 138 kHz in accordance with RSS-210. No particular requirements other than in section 3 of this report. From measurements performed as indicated below, the amplitude stability will not cause non-compliant situations with respect to exclusion bands or emissions outside permissible bands (band edges) Stability under special Amplitude deviation conditions (dB) Supply Voltage (Vdc) 12 (100%) N.A. 5 (-15%) 138.837 24 (+15%) 138.762 Table18 Amplitude stability of the EUT due to voltage variations. Note (Section 2.2.1 through 2.2.3): The applicant wants to state: Since both models incorporated the SmartReaderII V01.03 Main PWA and housed in a plastic enclosure that does not provide different insulative properties to the products – the carrier stability testing was completed on a potted 8141D only and is representative of all models. Test engineer Signature : Name : R. van der Meer Date : April 24, 2008 Project number : 08031403.fcc.smartreader Page 21 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 Plot 3 –Bandwidth of the emission at 138 kHz (Fundamental Carrier), for IC the measured Occupied Bandwidth is 75 Hz Project number : 08031403.fcc.smartreader Page 22 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 Carrier/Frequency Stability Test Setup Photos: Project number : 08031403.fcc.smartreader Page 23 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 4 Conducted emission data. 4.1 Conducted emission data of the EUT (125 kHz and 13.56MHz version) Supply Measurement results Measurement results Limits Voltage Frequency dB(µV) dB(µV) dB(µV) Result (V) (MHz) Neutral Line 1 QP AV QP AV QP AV 0.15 – 1 <20 <20 <20 <20 60.0 50.0 PASS 5.17 32 33 32 33 60.0 50.0 PASS 5 5.60 35 36 35 36 60.0 50.0 PASS 6.49 36 37 36 37 60.0 50.0 PASS 60.0 50.0 PASS 5.17 33 34 33 34 60.0 50.0 PASS 5.60 35 36 34 35 60.0 50.0 PASS 12 6.49 36 37 36 36 60.0 50.0 PASS 6.85 35 36 35 36 60.0 50.0 PASS 5.47 33 34 33 33 60.0 50.0 PASS 6.49 34 36 34 36 60.0 50.0 PASS 24 6.85 35 36 35 35 60.0 50.0 PASS 8.84 36 36 36 37 60.0 50.0 PASS Table 6 Conducted emission measurements. The results of the conducted emission tests, carried out in accordance with 47 CFR Part 15 section 15.207 & RSS-210, section 6.6, at the 110 Volts AC mains connection terminals of the AC/DC power supply which was connected to the EUT, are depicted in table 6. The EUT was tested in both passive and active mode (while detecting a card). Maximum values recorded. Notes: 1. The test unit was modified to add a resistive termination in lieu of the antenna. 2. The test data shown above is of the worst case EUT (8141D). 3. Measurement uncertainty is ±3.5dB Test engineer Signature : Name : R. van der Meer Date : April 29, 2008 Project number : 08031403.fcc.smartreader Page 24 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 4.2 Conducted emission data of the EUT (138 kHz and 13.56 MHz version) Supply Measurement results Measurement results Limits Voltage Frequency dB(µV) dB(µV) dB(µV) Result (V) (MHz) Neutral Line 1 QP AV QP AV QP AV 0.15 – 1 <20 <20 <20 <20 60.0 50.0 PASS 1.1914 29 26 29 25 60.0 50.0 PASS 5 3.603 33 25 33 25 60.0 50.0 PASS 3.777 31 22 31.1 22 60.0 50.0 PASS 4.1258 30.9 27 30.9 27 60.0 50.0 PASS 4.376 30.9 22 31.0 22 5M – 30M <30 <30 <30 <30 0.15 – 1 <20 <20 <20 <20 60.0 50.0 PASS 1.1914 31 27 32 27 60.0 50.0 PASS 12 3.603 34.1 28 35 28 60.0 50.0 PASS 3.777 31.3 23 31.5 23 60.0 50.0 PASS 4.1258 34.6 29 34.8 29 60.0 50.0 PASS 4.376 31.2 21 31.3 21 60.0 50.0 PASS 5M – 30M <30 <30 <30 <30 60.0 50.0 PASS 0.15 – 1 <20 <20 <20 <20 60.0 50.0 PASS 1.1914 27.8 26 28 26 60.0 50.0 PASS 24 3.603 34.1 28 34.3 28 60.0 50.0 PASS 3.777 32 24 32 24 60.0 50.0 PASS 4.1258 34.5 28 34.8 28 60.0 50.0 PASS 5M – 30M <30 <<30 <30 <30 60.0 50.0 PASS Table 6 Conducted emission measurements. The results of the conducted emission tests, carried out in accordance with 47 CFR Part 15 section 15.207 & RSS-210, section 6.6, at the 110 Volts AC mains connection terminals of the AC/DC power supply which was connected to the EUT, are depicted in table 6. The EUT was tested in both passive and active mode (while detecting a card). Maximum values recorded. Notes: 1. The test unit was modified to add a resistive termination in lieu of the antenna. 2. The test data shown above is of the worst case EUT (8141D). 3. Measurement uncertainty is ±3.5dB Test engineer Signature : Name : R. van der Meer Date : April 18, 2008 Project number : 08031403.fcc.smartreader Page 25 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 Conducted Emissions Test Setup Photos: 8141D Shown in Setup Photos Project number : 08031403.fcc.smartreader Page 26 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 5 List of utilized test equipment. Inventory Description Brand Model Last cal. Next cal. number 12476 Antenna mast EMCO TR3 NA NA 12477 Antenna mast 1-4 mtr Poelstra NA NA NA 12482 Loop antenna EMCO 6507 04/2008 04/2009 12503 LISN R&S ESH2-Z5 01/2008 01/2010 12513 LISN EMCO 3625/2 01/2008 01/2010 12640 Temperature chamber Heraeus VEM03/500 01/2008 01/2009 15275 Spectrum analyzer HP 8594E 10/2007 10/2008 99538 Spectrum analyzer R&S FSP40 04/28/2007 04/28/2008 99580 Open Area testsite Comtest NA 09/2006 09/2009 14051 Anechoic room Comtest NA NA NA 15633 Biconilog Testantenna Chase CBL 6111B 02/2008 02/2009 15667 Measuring receiver R&S ESCS 30 04/2007 04/2008 99045 Power supply Delta E030-3 04/2008 04/2009 99161 Variac 110Vac RFT LTS001 NA NA 99318 Digital multimeter HP 34401A 10/2007 10/2008 99596 Preamplifier 0.5 GHz - 18 Miteq AMF-5D-005180-28-13p 07/2006 07/2008 GHz NA= Not Applicable Project number : 08031403.fcc.smartreader Page 27 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 Appendix 1 HID Attestation of Similarity (added on request of the applicant) (Photos of Products on Following Page) Project number : 08031403.fcc.smartreader Page 28 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 Project number : 08031403.fcc.smartreader Page 29 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 Project number : 08031403.fcc.smartreader Page 30 of 31

Test specification(s): FCC Part 15, RSS-GEN, RSS-210 Description of EUT: 125kHz, 138 kHz and 13.56MHz Inductive Proximity Card Reader Manufacturer: HID Global Corporation Brand mark: HID Model: 814xD Incorporating the SmartReaderII V01.03 FCC & IC ID: JQ6-SmartTRANS2 – 2236B-SmartTRANS2 Project number : 08031403.fcc.smartreader Page 31 of 31


Document Created: 2008-05-15 13:04:37
Document Modified: 2008-05-15 13:04:37
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC