Cover Letter NEW

FCC ID: JQ6-SMARTTRANS1

Cover Letter(s)

Download: PDF
FCCID_925241

Feb. 20, 2008 To whom it may concern: This submittal for certification consists of different products that are comprised of the identical main board, RF Circuit and integral antenna on the main PCB. Since adequate testing of the non-keypad and keypad geometries was completed by TÜV Rheinland EPS B.V. (FCC Listed: 90828 and IC Registered IC3501 Site), and the fact that the plastic enclosure differences do not affect compliance; the model designation for certification for FCC shall be “803xD & 810xD Proximity Card Readers”. For Industry Canada, the Model Numbers listed shall be “8030D, 8031D, 8032D, 8100D and 8101D” (refer to the AoS on the following pages for differences). The FCC ID Shall Be: JQ6-SmartTRANS1 The IC ID Shall Be: 2236B-SmartID Sincerely, Todd Seeley Manager – Compliance Engineer HID Global Corporation

Attestation of Similarity The SmartID product family consists of different models that incorporate an identical main PWA (SmartReaderII V01.03) that has integral, Power Section, I/O Section, Digital Processing Section, RF Section and Antenna. This main board is then placed within different plastic enclosure that do not impact compliance for Safety, Radio, Emissions and most immunity requirements. In addition, other PWA’s may be added to the main PWA integral to the plastic enclosure to add functionality to the device (E.g. a passive Keypad, 125kHz prox, biometrics). In cases where the basic geometries may affect compliance – prescans are performed in order to identify the worst case model. All Engineering justifications and or compliance impacts are addressed within the report in the form of additional testing and/or or notes. The following 2 readers share the same basic product configuration geometry – the only difference between the 2 is one has a passive keypad overlaid across the main PWA on the outside of the enclosure. Reader Type Mullion – 13.56MHz Reader Enclosure Main PWA PWA #2 PWA# 3 Representative Test Sample SmartReaderII Plastic/Potted N/A N/A Configuration V01.03 Part Number 8030D Reader Type Mullion with Keypad – 13.56MHz Reader Enclosure Main PWA PWA #2 PWA# 3 Representative Test Sample Membrane SmartReaderII Configuration Plastic/Potted Keypad N/A V01.03 V01.00 Part Number 8031D Difference Description From The only difference of this Model from the 8030D above is that a passive 1st Model keypad is added – changing the product mechanical geometry that may effect emissions and immunity. Everything else is identical. Reader Type Desktop – 13.56MHz Reader Enclosure Main PWA PWA #2 PWA# 3 Representative Test Sample SmartReaderII Plastic N/A N/A Configuration V01.03 Part Number 8032D Difference Description From The only difference of this Model from the 8030D above is that it is 1st Model placed in a differently molded plastic enclosure. Everything else is identical. There is no other board (passive or active) within this product – therefore testing the 8030D applicable to the 8032D and does not need redone. However, ESD testing shall be done on this unit for the plastic housing is different than the 8030D.

The following 2 readers share the same basic product configuration geometry – the only difference between the 2 is one has a passive keypad overlaid across the main PWA on the outside of the enclosure. Reader Type Mullion – SmartTRANS – 13.56MHz&125kHz Reader Enclosure Main PWA PWA #2 PWA# 3 Representative Test Sample SmartReaderII SmartExtension125 Plastic/Potted N/A Configuration V01.03 V02.00 Part Number 8100D Difference Description From The only difference of this Model from the 8030D above is that it has an 1st Model add on PWA “SmartExtension125” that adds the ability to read 125kHz proximity cards that sits above the SmartReaderII board within the potting and plastic enclosure. Everything else is identical. (This model meets the <490kHz Exemption requirements for the 125kHz radio Section) Reader Type Mullion with Keypad – SmartTRANS – 13.56MHz&125kHz Reader Enclosure Main PWA PWA #2 PWA# 3 Representative Test Sample Membrane SmartReaderII SmartExtension125 Configuration Plastic/Potted Keypad V01.03 V02.00 V01.00 Part Number 8101D Difference Description From The only difference of this Model from the 8031D above is that it has an 1st Model add on PWA “SmartExtension125” that adds the ability to read 125kHz proximity cards that sits above the SmartReaderII board within the potting and plastic enclosure. Everything else is identical. (This model meets the <490kHz Exemption requirements for the 125kHz radio Section) Supporting product photos are on the following pages after the signature below. 2-10-2008 Company Representative Signature: Statement Date: Todd Seeley – Manager/Compliance Engineer

From Right to Left (Products in Plastic Enclosures) 1. 8030D Mullion Reader – Also Represents the 8100D 2. 8031D Mullion Reader with Keypad – Also Represents the 8101D 3. 8032D Desktop Reader/Programmer 4. SmartReaderII V01.03 Main PWA (the main active PWA incorporated in every product addressed by this AoS.


Document Created: 2008-04-08 18:30:49
Document Modified: 2008-04-08 18:30:49
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC