Installation guide

FCC ID: JQ6-RKCLB40E

Users Manual

Download: PDF
FCCID_3043445

INSTALLATION GUIDE iCLASS SE® Biometric/ iCLASS SE Display Reader RKCL40, RPKCL40, RKCLB40 SRD MODEL: RPKCL40E, RKCLB40E PLT-02738 A.0 Parts 1 - Reader and base plate assembly 1 - Installation guide 2 - Terminal connector 4 - M3.5 mm x 12 mm Phillips machine screw 4 - #6-32 x .375” Phillips self-tapping machine screw 4 - #6 x 1.5” Phillips sheet metal screw 3 - #6-32 x .4375” Spanner security screw, anti-tamper (black) 3 - #6-32 x .4375 Phillips security screw (black) 1 - Mounting Gasket Recommended • Cable, 6 conductor, 22 or 24 AWG [65 mm or 51 mm] Twisted Pair, Over-All Shield (Belden 3108A or equivalent) - RS-485 + power • Cable, 6 to 9 conductor, 22 or 24 AWG [65 mm or 51 mm] Over-All Shield, (Alpha 1296C or equivalent) - Wiegand + power • DC power supply • Metal or plastic double-gang junction box • Reader spacer when using metal junction boxes - see How to Order Guide • Security tool (for spanner security screw, anti-tamper) HID 04-0001-03 Specifications CURRENT BASE PART INPUT VOLTAGE OPERATING UL REF SRD PRODUCT Standby Maximum CABLE LENGTH NUMBER (VDC) PEAK3 TEMPERATURE NUMBER Model AVG1 AVG2 RKCL40 923N -4° to 149° F 150mA 185mA 250mA Wiegand and RS-485 RPKCL40Ex1x2x3 RPKCL40E (-20° to 65° C) RPKCL40 923P 12VDC 500 ft - 22 AWG (152 m) 300 ft - 24 AWG (91 m) 14° to 122° F RKCLB40 924N 165mA 215mA 275mA RKCLB40Ex1x2x3 RKCLB40E (-10° to 50° C) 1 Standby AVG - RMS current draw without a card in the RF field. UL Reference Number Deciphering 2 Maximum AVG - RMS current draw during continuous PIV card reads. x1 Reader Colors: K = Black, Not evaluated by UL. x2 Wiring: T = Terminal 3 Peak - highest instantaneous current draw during RF communication. x3 Communications: R = Module hid g l o b al.com An ASSA ABLOY Group brand

RKCL40E, RPKCL40E, RKCLB40E INSTALLATION GUIDE iCLASS SE Biometric/iCLASS SE Display SRD Model: RPKCL40E, RKCLB40E Installation 1 Mounting Attach Backplate and Mounting Gasket to Junction Box. Junction box not Mounting holes for US double- included. gang electrical boxes. Install gasket Wall backplate Reverse Configuration Rotating the backplate 180° allows for placing the LCD display on left and the reader on right. See Section B Alternate Reader Assembly for 2 Wiring Beeper GPIO1 instructions, before proceeding to Section 2: Wiring. GRN LED GP102 GND OC/TMPR +VDC DATA1/CLK DRAIN DATA2/DATA RED GPIO3 HOLD GPIO4 ATTENTION Observe precautions for handling GRN LED Beeper DRAIN HOLD +VDC GND RED Terminal Reader P1 ELECTROSTATIC SENSITIVE DEVICES GPIO4 GPIO3 DATA2/DATA DATA1/CLK OC/TMPR GP102 GPIO1 P2 (Terminal block and Note: Previous iCLASS readers had reversed module position varies) RS-485 wiring ( P2-7 & P2-6 - A & B). When upgrading, ensure proper connections as defined below. Pigtail Terminal Description Pigtail Terminal Description Yellow P1-1 Beeper Input Red / Green P2-7 GPIO1 (RS232-T / RS485-FDX/HDX-A) Orange P1-2 LED Input (GRN) Tan P2-6 GPIO2 (RS232-R / RS485-FDX/HDX-B) Black P1-3 Ground (RTN) Violet P2-5 *Open Collector Output / Tamper Red P1-4 +VDC White P2-4 **Wiegand Data 1 / Clock Drain P1-5 Unused Green P2-3 **Wiegand Data 0 / Data Brown P1-6 LED Input (RED) Pink P2-2 GPIO3 (RS485-FDX-Z) Blue P1-7 Hold Input Gray P2-1 GPIO4 (RS485-FDX-Y) *Tamper Output - When activated, output synchronizes to ground (default). **Dependent upon reader configuration. See the HTOG for Wiegand and Clock-in-Data configurations. This Installation Guide is for informational purposes only. HID makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output are fictitious. Specifications are subject to change without notice. © 2016 HID Global Corporation/ASSA ABLOY AB. All rights reserved. HID, the HID logo, and iCLASS are trademarks or registered trademarks of HID Global, or its licensors, in the U.S. and/or other countries. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owners. hid g l o b al.com An ASSA ABLOY Group brand

RKCL40E, RPKCL40E, RKCLB40E INSTALLATION GUIDE iCLASS SE Biometric/iCLASS SE Display SRD Model: RPKCL40E, RKCLB40E 3 Attach to Backplate Mount the Reader Assembly (Reader, Standard Configuration: Slide Reader Install Security screws. LCD Assembly, and reader backplate) Assembly towards the right to lock. to the wall backplate. Alternate Configuration: Slide Reader Assembly to the left to lock. 4 Power & Testing This Installation Guide is for informational purposes only. HID makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output are fictitious. Specifications are subject to change without notice. © 2016 HID Global Corporation/ASSA ABLOY AB. All rights reserved. HID, the HID logo, and iCLASS are trademarks or registered trademarks of HID Global, or its licensors, in the U.S. and/or other countries. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owners. hid g l o b al.com An ASSA ABLOY Group brand

RKCL40E, RPKCL40E, RKCLB40E INSTALLATION GUIDE iCLASS SE Biometric/iCLASS SE Display SRD Model: RPKCL40E, RKCLB40E A Biometric Reader Proper Usage Ensure a good quality Contact: • Do not press too hard • Do not move during image acquisition • Leave your finger on the sensor at least 2 seconds • Do not slide or roll your finger across the sensor Cleaning For optimum performance, it is recommended that the user clean the bio-reader periodically. The use of a dry cloth is recommended to clean the acquisition surface. Caution: Acidic liquids, alcohol or abrasive materials are prohibited. In order not to scratch the surface, remove all dust and residue with gentle movements. Acquisition Surface B Credential Presentation Best Practices To ensure a successful read of a card: 1. Hold card between the thumb and index finger. 2. Present the card so that the index finger creates a spacing between the card and the reader face. Do not place the card flat on the reader. 3. Place the card parallel to the reader form factor. Do not angle to the right or left 4. Place the card parallel to the reader face. Do not angle the card up or down from the reader face. This Installation Guide is for informational purposes only. HID makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output are fictitious. Specifications are subject to change without notice. © 2016 HID Global Corporation/ASSA ABLOY AB. All rights reserved. HID, the HID logo, and iCLASS are trademarks or registered trademarks of HID Global, or its licensors, in the U.S. and/or other countries. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owners. hid g l o b al.com An ASSA ABLOY Group brand

RKCL40E, RPKCL40E, RKCLB40E INSTALLATION GUIDE iCLASS SE Biometric/iCLASS SE Display SRD Model: RPKCL40E, RKCLB40E E Alternate Reader Assembly Standard Configuration The following steps reconfigure the reader assembly to position the LCD Display component on the left side of the assembly. Alternate Configuration 1. Disassemble the Reader. • Remove the Reader from the backplate. • Carefully unplug the ribbon cable from the module in the back of the Reader. Caution: Do not pull on the ribbon cable as this may damage the connection to the connector. Reader LCD Display • Remove the LCD Display from the backplate. • Gently pull the ribbon cable through the backplate. Ribbon cable LCD Display Reader Reader Backplate LCD Display Reader 2. Reassemble with the LCD Display on the left side of the assembly. • Rotate the backplate so that the large cutout for the power cable is on the left • Gently route the ribbon cable back through the backplate slots, as shown below • Plug the ribbon cable back into the module (back of Reader) and ensure module is fully Test card seated into the reader • Attach the LCD Display to the backplate (this must be installed first, as the Reader will fit slightly over the LCD Display) • Attach the Reader to the backplate (power cable must be threaded through the large square cutout on the backplate) • Return to Section 2. Ribbon cable Reader Backplate Reader LCD Display This Installation Guide is for informational purposes only. HID makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output are fictitious. Specifications are subject to change without notice. © 2016 HID Global Corporation/ASSA ABLOY AB. All rights reserved. HID, the HID logo, and iCLASS are trademarks or registered trademarks of HID Global, or its licensors, in the U.S. and/or other countries. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owners. hid g l o b al.com An ASSA ABLOY Group brand

RKCL40E, RPKCL40E, RKCLB40E INSTALLATION GUIDE iCLASS SE Biometric/iCLASS SE Display SRD Model: RPKCL40E, RKCLB40E Regulatory The final product, containing the modular transmitter must be labeled with its own FCC ID and IC ID. If the FCC & IC ID is not visible, when the module is installed inside another device, then the final assembly label must contain the FCC and IC ID numbers with a statement such as follows: “Contains Transmitter Module with FCC ID JQ6-ICLASSBTM and IC ID 2236B-ICLASSBTM”. UL Connect only to a Listed Access Control / Burglary power-limited power supply. These readers are intended to be used with listed (UL294) control equipment. Suitable for outdoor use. Only Wiegand and RS-485 communications have been evaluated by UL. FCC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Any changes or modifcations to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. Indala Prox products RP10EL, RP15EL, RP30EL, RP40EL and RPK40EL are certified for FCC, Canada Radio Certification and CE Marking only. Canada Radio Certification This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. CE Marking HID Global hereby declares that these proximity readers are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Por el presente, HID Global declara que estos lectores de proximidad cumplen con los requisitos esenciales y otras disposiciones relevantes de la Directiva 1999/5/EC. HID Global déclare par la présente que ces lecteurs à proximité sont conformes aux exigences essentielles et aux autres stipulations pertinentes de la Directive 1999/5/CE. A HID Global, por meio deste, declara que estes leitores de proximidade estão em conformidade com as exigências essenciais e outras condições da diretiva 1999/5/EC. HID Global bestätigt hiermit, dass die Leser die wesentlichen Anforderungen und anderen relevanten Bestimmungen der Richtlinie 1999/5/EG erfüllen. HID Global dichiara che i lettori di prossimità sono conformi ai requisiti essenziali e ad altre misure rilevanti come previsto dalla Direttiva europea 1999/5/EC. Download copies of the R&TTE Declaration of Conformity (DoC) at http://www.hidglobal.com/certifications. Brazil Compliance Statement Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução 242/2000, e atende aos requisitos técnicos aplicados. Para maiores informações, consulte o site da ANATEL - www.anatel.gov.br This product is homologated at ANATEL according to procedure regulated by Resolution 242/2000, and it complies with the applicable technical requirements. For more information, consult ANATEL website - www.anatel.gov.br RF Warning Statement Per Article 6 of Resolution 506, equipment of restricted radiation must carry the following statement in a visible location: Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. This equipment operates in secondary character, meaning it does not have the right of protection against harmful interference, even against those the same character, and it cannot cause any interference to systems operating in the primary character. This Installation Guide is for informational purposes only. HID makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output are fictitious. Specifications are subject to change without notice. © 2016 HID Global Corporation/ASSA ABLOY AB. All rights reserved. HID, the HID logo, and iCLASS are trademarks or registered trademarks of HID Global, or its licensors, in the U.S. and/or other countries. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owners. hid g l o b al.com An ASSA ABLOY Group brand

RKCL40E, RPKCL40E, RKCLB40E INSTALLATION GUIDE iCLASS SE Biometric/iCLASS SE Display SRD Model: RPKCL40E, RKCLB40E iCLASS Keypad Readers FOTO SELO ANATEL Fabricante: HID Global Corporation Modelo: iCLASS SE RK40E, multiCLASS RPK40E Este produto esta aprovada pela Anatel, de acordo com os procedimentos regulamentados pela Resolução nº 242/2000 e atende aos requisitos técnicos aplicados. “Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário” iCLASS Non-Keypad Readers FOTO SELO ANATEL Fabricante: HID Global Corporation Modelo: iCLASS SE R10, multiCLASS RP10E, multiCLASS RP30E iCLASS SE R40E, multiCLASS RP15E, multiCLASS RP40E Este produto esta aprovada pela Anatel, de acordo com os procedimentos regulamentados pela Resolução nº 242/2000 e atende aos requisitos técnicos aplicados. “Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário” This Installation Guide is for informational purposes only. HID makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output are fictitious. Specifications are subject to change without notice. © 2016 HID Global Corporation/ASSA ABLOY AB. All rights reserved. HID, the HID logo, and iCLASS are trademarks or registered trademarks of HID Global, or its licensors, in the U.S. and/or other countries. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owners. hid g l o b al.com An ASSA ABLOY Group brand

RKCL40E, RPKCL40E, RKCLB40E INSTALLATION GUIDE iCLASS SE Biometric/iCLASS SE Display SRD Model: RPKCL40E, RKCLB40E Taiwan According to “Administrative Regulations on Low Power Radio Waves Radiated Devices” Without permission granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to a approved low power radio-frequency devices. The low power radio-frequency devices shall not influence aircraft security and interfere legal communications; If found, the user shall cease operating immediately until no interference is achieved. The said legal communications means radio communications is operated in compliance with the Telecommunications Act. The low power radio-frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices. Japan MIC “ この装置は総務省の型式指定を受けています。” (総務省指定番号は第AC-ｘｘｘｘｘ号です) 本製品は電波を使用したRFID 機器の読み取り・書き込み装置です。 そのため使用する用途・場所によっては、医療機器に影響を与える恐れがあります Singapore Complies with IDA Standards DA103548 Korean KCC R10E, R15E, R30E, and R40E RP10E, RP15E, RP30E and RP40E RK40E RPK40E 항목 규격 RFID:13.5607 MHz, 송신주파수 RFID:13.56 MHz LPD:125 KHz RFID:13.56 MHz, 수신주파수 RFID:13.56 MHz LPD:125 KHz RFID: 10m에서 RFID: 10m에서 47.544mv이하. 출력 47.544mv이하 LPD:3 m 거리에서 500 ㎶/m이하 전원 DC 16.0V 전파형식 A1D X-tal (13.56MHz) 발진방식 X-tal Resonator(125kHz) 변조방식 AM AM(13.56MHz), FSK(125kHz) HID Global Americas & Corporate Asia Pacific Europe, Middle East & Africa 611 Center Ridge Drive 19/F 625 King's Road Phoenix Road Austin, TX 78758 North Point, Island East Haverhill, Suffolk CB9 7AE USA Hong Kong England Support: 866-607-7339 Support: 852-3160-9833 Support: 55 11 5514-7100 Fax: 949-732-2120 Fax: 852-3160-4809 Fax: 55 11 5514-7109 For additional offices around the world, see www.hidglobal.com corporate offices. HID Global Customer Support: www.hidglobal.com/support Equipment 8T29 General Signaling ACC Control Reader Equipment h id g l o bal.com An ASSA ABLOY Group brand


Document Created: 2016-04-12 08:14:31
Document Modified: 2016-04-12 08:14:31
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC