User Manual

FCC ID: JPZ0108

Users Manual

Download: PDF
FCCID_2363070

Required Components Project 37 | Installation For each fixture, ensure that you have: Technical Assistance | 1.800.523.9466 USA, Canada, and the Caribbean | +44.(0)20.7702.0657 Europe | +1.610.282.3800 Others | www.lutron.com One Project 37 Control Module At least one Sensor or Pico® Wireless Control At least one 0 – 10 V Fluorescent Ballast or LED Driver 041467 Part of the Energi TriPak® Family Rev. A Load Status LED 07/2014 Consult third-party 0 – 10 V fixtures installation guide for fixture-specific wiring. Raise PIR Lens Laser Detection FC-1 (Project 37 120 – 277 V~ 50 / 60 Hz 1 A Toggle Control Module) + + Daylight Lens UL 2043 Plenum Rated Lower FC-0 12 V- 25 mA (Project 37 Sensor) Project 37 Occupancy/Vacancy and Radio Powr SavrTM Pico® Wireless Project 37 Control Module with 0 –10 V Daylight Sensor (1 maximum) Occupancy/Vacancy Sensor Control 6 mA maximum for the control lines. Switches up to 1 A total. May be Note: Project 37 Control Module can be used without a Sensor (10 maximum) (10 maximum) pre-installed in light fixture. Control: 0–10 V- 6 mA Hot (Bla Important Notes: Please read before installing. For installation by a qualified electrician in accordance with all Start Here local and national electrical codes. Hot (Black) Neutral • • Note: Use copper conductors only. Check to see that the device type and rating is suitable for the 1 Install Project 37 Control Module Green/Yellow 2 Install the Sensor Fixture Earth application. and Sensor Neutral Neutral (White) The Project 37 sensor mounts to the ceiling surface with a supplied wireform clip. • DO NOT install if product has any visible damage. Suggested Installation Location: Close to the NEU Two wires connect to the control module and can either be routed through a hole in MAINS • If moisture or condensation is evident, allow the product to dry Fixture/Troffer. Switched Hot (Red) HOT the ceiling or across the ceiling surface. DO NOT install on ceilings higher than 12 ft completely before installation. (3.7 m). The sensor should be installed in a location where it has a good view of the • Operate between 0 °C and 40 °C, ambient. WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit breaker before installing the unit. Violet space that it is meant to cover. • Class 2 0% to 90% humidity, non-condensing. + – • For indoor use only. The Project 37 Control Module can be installed in a Fixture/Troffer Gray A Slide closed end of wire form under fixture/troffer, junction box or marshalling box using the or Junction the two retention arms on the back Box 1/2 in (21 mm) Knockout Opening conduit nut (provided) or with mounting screws (not of the sensor Project 37 provided). Please consult local and national electric Conduit Nut Control Module codes for proper installation. Install control module directly to fixture or in junction box nearest the fixture. Install sensor If installing unit inside a junction box, please see in ceiling near fixture so as to optimize cover- Application Note #423 at Spring arms age in the desired area. B While continuing to push against the www.lutron.com/TechnicalDocumentLibrary/048423.pdf retention arms, rock the other side of English Project 37 Control Sensor B Ideally mount the sensor to the ceiling tile close to the the wireform down against the sensor Module fixture using the wire form or using the command strips and slide them into place under the (included). The 2 communication wires from the sensor loop retention features attaches to the control module poke in connectors. 30 ft (9 m) 30 ft (9 m) max C Once installed, energize the Project 37 Control Module. Note: For solid ceilings or others where the wireform From back of sensor C Push wireform through tile and cannot be utilized, use the Pico® bend on the backside of the tile to supplied Command strips Wireless Control complete the mounting. to adhere sensor to desired location on ceiling or fixture. 40 ft (12 m) All Wireless Transmitters 3 Associate Wireless Transmitters to Project 37 Control Module Sensor Detection Range must be Before beginning this step, make sure that there are no other Project 37 Control Modules being set up in the building which are currently in this Ceiling installed within 30 ft (9 m) of the association mode.. It is possible that wireless transmitters from other systems can be incorrectly associated to this module. Project 37 Control Module. 9 ft (2.75 m) A Initiate association mode on the Project 37 Control Module by shining a green B Hold the indicated button on each transmitter laser pointer at the laser detection hole on the sensor until the load attached to for 6 seconds. The fixture will flash to show that Floor the Project 37 Control Module starts flashing every 2 seconds. wireless transmitters have been associated. 15 ft 9 ft 3 ft 0 3 ft 9 ft 15 ft (4.6 m) (2.7 m) (0.9 m) (0.9 m) (2.7 m) (4.6 m) Alternatively, press and hold the toggle button for 6 seconds on the Project 37 To associate another transmitter, repeat steps Control Module to initiate association mode. 4A and 4B. 400 ft2 (37 m2) maximum coverage area of one sensor whenmounted on an 9 ft (2.75 m) ceiling Default Functionality 15 ft (4.6 m) Wireless Controls Laser Detection (smallest) On All lights 100% Link Test 9 ft (2.7 m) Favorite All lights 50% Off All lights off OR 3 ft (0.9 m) 0 3 ft (0.9 m) Green laser specifications: 9 ft • Wave output: constant (2.7 m) • Wavelength: 532 nm • Output power: 5 mW maximum 15 ft (4.6 m) Lutron Electronics Co., Inc., 7200 Suter Road 15 ft 9 ft 3 ft 0 3 ft 9 ft 15 ft Coopersburg, PA 18036-1299 U.S.A. (4.6 m) (2.7 m) (0.9 m) (0.9 m) (2.7 m) (4.6 m)

Project 37 Load Control Module | 4 Set a Favorite Light Level Technical Assistance | 1.800.523.9466 USA, Canada, and the Caribbean | +44.(0)20.7702.0657 Europe | +1.610.282.3800 Others | www.lutron.com For Pico® Wireless Controls with a Favorite Button. Programming FCC Information (FC-0, FC-1 and FC-2 only) Part of the Energi TriPakR Family 041467 This device complies with part 15 of the FCC Rules and Industry A Adjust lights to desired level: Rev. A 07/2014 Raise Lower Canada license-exempt RSS standard(s). Operation is subject ALL PROGRAMMING IS OPTIONAL Use Raise button “ ” or Lower button “ ” on Pico® wireless control. to the following two conditions: (1) This device may not cause Programming is not required for default functionality interference, and (2) this device must accept any interference, • Set a favorite light level including interference that may cause undesired operation. Modifications not expressly approved by Lutron Electronics Co., • Set high-end and low-end trim for all fixtures Inc. could void the user’s authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide B Save favorite level: reasonable protection against harmful interference in a residential Favorite installation. This equipment generates, uses and can radiate radio Press and hold Favorite button for 6 seconds. frequency energy and, if not installed and used in accordance The load flashes 3 times to confirm that the set level is saved. with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is 5 Set Low-End and High-End Trim encouraged to try to correct the interference by one or more of the following measures: Reset Factory Defaults For best results, minimize the amount of sunlight entering the room before performing the following procedures. • Re-orient or relocate the receiving antenna. Note: In some instances, it may be necessary Low-End Trim • Increase the separation between the equipment and receiver. to reset the PowPak® Dimming Module and • Connect the equipment into an outlet on a circuit different from A Enter low-end trim adjustment mode: that to which the receiver is connected. connected devices back to factory default settings. Before beginning, make sure that all Press and hold Lower button “ ” for 12 seconds. devices are connected and powered. Lights will flash high-low-high and LED will begin flashing. A Triple-tap any button on the PowPak® Dimming B Adjust the low-end trim: Limited Warranty Module and hold until the LED begins to flash Lutron EA Ltd. (“Lutron EA”) warrants each unit to be free from Use Raise button “ ” and Lower button “ ” to adjust and set the lights to the desired low-end (1 to 45%). slowly; release button. defects in material and workmanship and to perform under C Save the low-end trim: normal use and service. To the extent permitted by law, Lutron B Within 3 seconds of the start of flashing, triple‑tap Press and hold Toggle button “ ” for 6 seconds to save setting. EA and Lutron Electronics Co. Inc. (“Lutron”) make no warranties the same button again and the LEDs will flash Notes or representations as to the units except as set forth herein. This rapidly indicating that the unit has been reset to LED will begin flashing and then turn solid to indicate new level has been saved. warranty shall run for a period of two years from the date of purchase Depending on the fixture and Lutron’s obligations under this warranty are limited to remedying factory defaults. High-End Trim manufacturer or load, low-end any defect, replacing any defective part or replacement (at Lutron Note: Any associations or programming D Enter high-end trim adjustment mode: and high-end trim may need to EA’s sole option) and shall be effective only if the defective unit be adjusted. previously set up with the PowPak® will be erased is shipped to Lutron EA postage prepaid within 24 months after Press and hold Raise button “ ” for 12 seconds. • Trim low-end to ensure a stable and will need to be re‑programmed. purchase of the unit. Repair or replacement of the unit does not affect Lights will flash high-low-high and LED will flash. light level because some loads the expiry date of the warranty. This warranty does not cover damage will flicker or drop out if trimmed too low. or deficiencies due to abuse, misuse, inadequate wiring or insulation E Adjust the high-end trim: or use or installation other than in accordance with instructions Use Raise button “ ” and Lower button “ ” to adjust and set the lights to the desired high-end • Be sure that you can turn on the accompanying the unit. lights to the low-end trim level (55 to 100%). without any abnormal operation. To the extent permitted by law, neither Lutron EA nor Lutron shall be F Save the high-end trim: • The factory default high-end trim liable for any other loss or damage including consequential or special will normally be sufficient for most loss or damages, loss of profits, loss of income, or loss of contracts Press and hold Toggle button “ ” for 6 seconds to save setting. applications. Trim as desired. arising out of or relating to the supply of the unit or the use of the unit LED will begin flashing and then turn solid to indicate new level has been and the purchaser assumes and will hold harmless Lutron EA and Lutron in respect of all such loss or damage. Nothing in this warranty Troubleshooting www.lutron.com shall have the effect of limiting or excluding Lutron EA’s or Lutron’s liability for fraud or for death or personal injury resulting from its own Ballasts cannot be controlled locally from • Ensure that the breaker(s) to the PowPak® Dimming Module are energized. negligence, or any other liability, if and to the extent that the same PowPak® Dimming Module. • Ensure that the PowPak® Dimming Module switched hot lead is wired to the ballast(s). may not be limited or excluded as a matter of law. • Ensure that the PowPak® Dimming Module 0 –10 V control lines are wired to the ballast(s). This warranty does not affect the statutory rights of consumer purchasers of this product. Reset to factory defaults. Although every attempt is made to ensure that catalogue information Lights do not dim or turn ON as expected. • Ensure that 0 –10 V control lines are wired properly. is accurate and up-to-date, please check with Lutron EA before • Ensure that fixture does not require an inverted signal (10 – 0 V control). specifying or purchasing this equipment to confirm availability, exact • Ensure that the wires are connected between the Project 37 Sensor and Project 37 Control Module specifications, and suitability for your application. For information on other products, please see the Warranty Lights do not respond to Wireless Transmitter(s). • Ensure that the breaker(s) to the PowPak® Dimming Module and ballasts are energized. enclosed with the product. • Ensure that Wireless Transmitters are associated to the PowPak® Dimming Module. Lutron, Pico, PowPak, Energi TriPak, Clear Connect, EcoSystem, Reset to factory defaults. and ) are registered trademarks and Radio Powr Savr is a trademark of Lutron Electronics Co., Inc. Lights are unstable at low‑end or flash/flicker at • Adjust low-end trim. ©2014 Lutron Electronics Co., Inc. turn-on or turn-off. Wireless Transmitter(s) cannot be associated to • The maximum number of Wireless Transmitters have been associated to the PowPak® Dimming Module. To remove a previously set up Wireless PowPak® Dimming Module. Transmitter, tap a Wireless Transmitter button three times; on the third tap hold for three seconds and then tap three more times. Lutron Electronics Co., Inc., 7200 Suter Road Coopersburg, PA 18036-1299 U.S.A.


Document Created: 2014-07-31 09:59:40
Document Modified: 2014-07-31 09:59:40
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC