User manual

FCC ID: JPZ0107

Users Manual

Download: PDF
FCCID_2311379

GrafikTT Installation Instructions English 0301742 Rev A Installation 1 Turn OFF power at circuit breaker. 6b Multi-location - Lights can be dimmed from multiple locations. Ganging and Derating When combining controls in the same wallbox, derating is required. No derating is One location will be replaced by a GrafikTTM dimmer and the other location(s) by a GrafikTTM required for companion dimmers. Please Read Before Installing 120 V~ 60 Hz companion dimmer. The dimmer can be wired on the line-side or the load-side. Dimmers LED Incand. / Halogen Hi-lume® A-Series LTE LED Drivers ! WTurn ARNING! Shock Hazard. May result in serious injury or death. off power at circuit breaker before installing the unit. Dimmer Control 1 Load Type Not Ganged End of Gang Middle of Gang GTJ-150 150 W Connect the green ground wire on the dimmer to the green or bare ground wire in the wallbox GT-150 LED 150 W 150 W 150 W — (See Important Note 3 at left). GTJ-150 GT-150 150 W Incand. / Halogen 600 W 500 W 400 W GT-250M 250 W 2 Remove wallplate and the switch mounting screws. Leaving all wires attached, Connect tagged wire removed from the switch to the black wire on the dimmer. LED 250 W 250 W 250 W GTJ-250M 250W 600 W 350 W carefully pull the switch out from the wall. Connect one of the remaining wires removed from switch to the red wire on the dimmer. GT-250M RRT-25CL 250 W 8 maximum Connect the remaining wire removed from the switch to the blue wire on the dimmer. GTJ-250M Incand. / Halogen 600 W 500 W 400 W HQRT-25CL 250 W 3 Identify switch type. Companion Dimmer RRT-25CL Lutron® Hi-lume® 350 W, 350 W, 350 W, A-Series LTE LED Companion dimmers Connect the green wire on the dimmer to the green or bare ground wire in the wallbox (See HQRT-25CL Driver 8 drivers max 8 drivers max 8 drivers max GT-AD-S For use with HQRT-25CL and RRT-25CL Single-pole – The switch will have Multi-location – 3-way switches will have Important Note 3 at left). insulated wires connected to two insulated wires connected to three screws Connect the same color wire connected to the red wire on the dimmer to the red wire on the GT-AD For use with all other models screws of the same color plus a green plus a green ground screw. One of the wires is Designed for use with permanently installed LED, incandescent, or tungsten halogen only. 1 companion dimmer, along with the tagged wire. ground screw. connected to a screw of a different color (not Connect the remaining wire to the blue wire on the companion dimmer. Compatible LEDs green) or labeled COMMON. Tag this wire. Cree®: 499485; CR6X-PP2 Dimmer Line-Side Minimum Load Chart Philips®: 426122(9290002330)(822580)(bc=046677426125) EcoSmart®: ECO-575L Red Red Tag Load Type Sylvania®: 78390 (LED8R20/DIM/SE/830/RP) Live Black Number of Incandescent / Companion Application LED 1 FEIT (Utilitech): PAR38/LEDG5 Ground Tag Dimmer Dimmer Light Companion Dimmers Halogen For a complete list of compatible LEDs, please visit: www.lutron.com/LED Ground Single-pole 0 2 LED lamps 40 W Tag Green Green Multi-location 1 3 LED lamps 80 W Important Notes Multi-location 2 4 LED lamps 120 W Different-colored screw 1. C  AUTION: To avoid overheating and possible damage to other equipment, do Blue Multi-location 3 5 LED lamps 160 W not use to control receptacles, fluorescent lighting fixtures, motor-operated Neutral Multi-location 4 6 LED lamps 200 W appliances, transformer-supplied appliances, or electronic low-voltage 4 The switch may have two wires attached to the same screw. Tape these two wires together before disconnecting. Proceed to disconnect the wires from the lighting fixtures. switch. 1 For performance or compatibility information, Lutron recommends visiting our website www. 2. Install in accordance with all national and local electrical codes. Dimmer Load-Side lutron.com/LED, which is constantly being updated. 3. W hen no “grounding means” exist in wallbox, the NEC® allows dimmer without a grounding connection to be installed as a replacement if 1) a nonmetallic, noncombustible faceplate is used with nonmetallic attachment screws or 2) the 5 Remove wallplate from the GrafikTTM dimmer and any companion dimmer, but Red Red leave wallplate adapter connected. Troubleshooting circuit is protected by a ground fault circuit interrupter (GFCI). For this type of Live Companion Dimmer Black installation, cap or remove the green ground wire on the dimmer, and use an Tag Dimmer Light appropriate wallplate, such as a Lutron® GrafikTTM series wallplate. Tag Symptom Possible Cause Green Green 4. GrafikTTM dimmers are not compatible with standard 3-way switches. Use only with Light does not turn On and no • The FASSTM on the dimmer is pulled down to the companion dimmers (GT-AD-S or GT-AD). LEDs turn On. Off position. Blue 5. C  ompanion dimmers (GT-AD-S or GT-AD) cannot be used individually but must be • Light bulb(s) burned out. used in conjunction with a GrafikTTM dimmer in a multi-location application. Neutral • Breaker is OFF or tripped. 6. In any multi-location circuit, use only one GrafikTTM dimmer with up to four • Dimmer is miswired. Check wiring. companion dimmers. Unit is non-responsive. • Cycle power to unit by pulling the FASSTM down 7. GrafikTTM dimmer settings such as Light Bar Intensity and Speaker On/Off can be modified using Advanced Programming Mode. For instructions and information on 7 Carefully push wires into the wallbox. Install dimmer/companion dimmer(s) and and back up to fully restore power. snap on wallplate. Light turns On and dimmer • Wire connected to the blue wire on the dimmer is how to use Advanced Programming Mode, please visit www.lutron.com/grafikT or works, but companion dimmer not the same wire connected to the blue wire on call Lutron® Technical Support at 1.800.523.9466. 6 Install dimmer and/or companion dimmer. does not work. the companion dimmer. Check wiring. Wire connectors provided are for copper wire • Wire connected to the red wire on the dimmer is Dimming Operation IMPORTANT only. For aluminum wire, consult an electrician. not the same wire connected to the red wire on the companion dimmer. Check wiring. Set High-End Trim: Adjust • Touch to set lights to 6a Single-pole - Switch will be replaced by a dimmer. Lights repeatedly turn On and • Load is less than the minimum load. See the 1. Press and hold top of Off. Minimum Load Chart to determine the acceptable light bar (approximately 5 desired level Connect the green ground wire on the dimmer to the green or bare ground seconds) until Toggle button wire in the wallbox. (See Important Note 3 at left.) minimum load. • Slide to adjust light level Lights are flickering or exhibiting • Set low-end trim. See Dimming Operation for flashes orange. Connect the black wire on the dimmer to one of the wires removed from the 8 Turn ON power at circuit breaker. poor dimming range. details. 2. Slide finger on light bar to switch. If you had taped together two wires (see step 4), connect both wires adjust to desired brightness. to the black wire on the dimmer and remove the tape. 3. To exit, press and hold the Toggle button (approximately Toggle Connect the red wire on the dimmer to the other wire removed from the 9 If needed, set low-end trim. See Dimming Operation section (at lower left) for 5 seconds) until the Toggle • Touch to turn Off or to switch. details. Additional Information button stops flashing. turn On to previous light For warranty details, please visit: level Red 10 Associate GrafikTTM dimmer to Clear Connect® devices (GTJ- models only). www/lutron.com/warranty Set Low-End Trim: • Toggle button is white Press and hold the Toggle button on the GrafikTTM dimmer for approximately 6 1. Press and hold bottom of when On, orange when seconds. Once all of the light bar LEDs begin to flash, release the Toggle button. For FCC/IC information, please visit: Dimmer light bar (approximately 5 Off Live www.lutron.com/fcc-ic Black Blue seconds) until Toggle button Press and hold the appropriate button on the device (see pictures below) for flashes orange. approximately 6 seconds. Lutron is a registered trademark and FASS and GrafikT are trademarks of Lutron Electronics Co., Inc. 2. Slide finger on light bar to NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts. Green adjust to desired brightness. 120 V~ Light © 2014 Lutron Electronics Co., Inc. 60 Hz 3. To exit, press and hold the Toggle button (approximately FASSTM - Front Accessible Service Switch Ground 5 seconds) until the Toggle Note: FASSTM is not available on companion Neutral Technical Assistance Off button stops flashing. dimmers. LUTRON Pico® Occupancy / Daylight Sensor IMPORTANT NOTICE: FASSTM - Front Accessible Service Switch Wireless Controller Vacancy Sensor 1.800.523.9466 U.S.A. | Canada | Caribbean To replace bulb(s), power may be conveniently removed by pulling the FASSTM down on the dimmer. After +1.888.235.2910 Mexico Cap the blue wire with the blue connector. Once the dimmer associates the recently added devices, the LEDs and load will replacing bulb(s), push the FASSTM back up fully to restore power to the dimmer. For any procedure, other than routine lamp replacement, power must be turned OFF at the main IMPORTANT This wire does not get connected. flash 3 times and the GrafikTTM dimmer will exit set-up mode. +1.610.282.3800 Others electrical panel. www.lutron.com Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299


Document Created: 2014-06-18 08:31:59
Document Modified: 2014-06-18 08:31:59
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC