User Manual

FCC ID: JPZ0087

Users Manual

Download: PDF
FCCID_1620322

English Dimensions Connection Operation Clear ConnectT Translator Measurements are in inches (mm). NXB-CCG 6.25 (top view) 5V 2A Power/Status LED (158.8) RF range: DC Adapter: PS-5DC-20-BL Installation Instructions Output: 5 V 2A To other devices 30 ft (9 m) Displays power status and other system status Please Read Before Installing Typical Power Consumption*: 5 W indicators. Features RF LED     •Supports system setup and ensures error-free communication between Displays the Tx / Rx system components. activity on the RF link.     •Reset button returns the Clear ConnectT Translator to factory settings.     •Ethernet port for integration and PC connectivity. Ethernet LED     •LED feedback for RF and Ethernet communication. 4.42 Displays the connection     •LED feedback for Power status. (112.3) status and Tx / Rx activity 2.72 on the Ethernet link. Important Notes (69) Environment Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C), 0% to 90% humidity, non-condensing. Indoor use only. Codes Install in accordance with all local and national electrical codes. 2.60 (bottom view) (66) Cleaning 1.30 To clean, wipe with a clean damp cloth. DO NOT use any chemical (33) cleaning solutions. DC Adapter Power NOTICE - Using a DC adapter not rated at the proper specifications could Mounting Diagram (side view) damage the Clear ConnectT Translator and possibly overheat the DC adapter. Use only the LutronR DC adapter listed above. Vertical Returning a Clear ConnectT Translator to Factory RF Device Placement Settings All dimmers, switches, keypads and shades / draperies must be located Note: Returning a Clear ConnectT Translator to factory settings will erase within 30 ft (9 m) of a Clear ConnectT Translator. all programming from it and all system devices and will require the Clear #6 (M3) screw ConnectT Translator to be reprogrammed into the system. Installation recommended 1. Find a suitable location for the Clear ConnectT Translator. 1. Press and hold the Reset button on the Clear ConnectT Translator for  ount vertically or horizontally, as shown in the Mounting Diagram, using 2. M 30 seconds. two #6 (M3) screws. When mounting, allow 7 in (177.8 mm) clearance for Wall 2. T  he Power/Status LED will start flashing slowly for approximately CAT5 Cable: Reset Button the antenna and ensure convenient access to the power plug. In order to Horizontal Press and hold 10 seconds after which it will start rapidly flashing for approximately maximum 328 ft achieve proper RF performance, do not mount unit in a metal enclosure. for 30 seconds to 20 seconds and then remain on. (100 m) 3. A  ttach the DC adapter cord to the power jack on the Clear ConnectT restore the system to the Factory 3. The Clear ConnectT Translator has been returned to factory settings. Translator and insert the DC adapter plug into a receptacle. settings. FCC/ IC Information This device complies with part 15 of the FCC Rules and Industry Canada license- USB Cable: Power Jack (to DC adapter) exempt RSS standard(s). Operation is subject to the following two conditions: (1) This Level Surface (Lutron use only) (IEC PELV / NECR Class 2) device may not cause interference, and (2) this device must accept any interference, 1.00 including interference that may cause undesired operation. Modifications not expressly (Model: PS-5DC-20-BL) approved by Lutron Electronics Co., Inc. could void the user’s authority to operate this (25.4) equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. RF Configuration This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference Ethernet Pin Numbering to radio communications. However, there is no guarantee that interference will not Clear ConnectT Translator occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the 87654321 receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. 30 ft (9 m) maximum Ethernet Pin # T+Ve 1 T-Ve6 7 82 9 1 2 R+Ve 3 34 5 Warranty: For warranty information, please see the Warranty enclosed R-Ve 6 with the product, or visit www.lutron.com/resiinfo *Typical Power Consumption test conditions: one LED on, Ethernet cable plugged in, Clear ConnectT Translator powered by the 5 V adapter supplied. Lutron Elec­tron­ics Co., Inc. NEC is a registered trademark of National Fire Protection Association, Quincy, Massachusetts. Lutron and are registered trademarks and Clear Connect is a trademark of 7200 Suter Road Lutron Electronics Co., Inc. Coopersburg, PA 18036-1299 © 2011 Lutron Electronics Co., Inc. P/N 044-297 Rev. A 11/2011


Document Created: 2012-01-03 10:02:38
Document Modified: 2012-01-03 10:02:38
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC