User Manual 7

FCC ID: JPZ0062

Users Manual

Download: PDF
FCCID_1175469

English Multigang Installations Wiring Diagram 1 Wiring Diagram 2 Troubleshooting Guide Designer-Style RF Maestro® In multigang installations, several controls Trim or strip wallbox wires to the length Dimmers: RRD-6D, RRD-10D, RRD-10ND Single Location Installation Single Location Installation with Neutral are grouped horizontally in one multigang indicated by the strip gauge on the back of the Symptom Probable Cause and Action Switch: RRD-8ANS -6D, -10D -10ND, -8ANS wallbox. control. Typical Power Consumption*: 0.2 W Dimmer / Switch Lights don’t switch Power not present Remote Dimmer: RD-RD When combining controls in a wallbox, Push-In Terminals: Insert Dimmer ON / OFF when • Circuit breaker OFF or tripped. Perform Short Circuit Check. Remote Switch: RD-RS derating is required; however, no derating wires fully. To release wire, Installation Instructions Brass Blue Brass Blue Tapswitch on •F  ASS is in the OFF position. Move FASS to the ON position Typical Power Consumption*: 0 W is required for Remote Dimmers / Switches. insert small, flat screwdriver Tighten1 Tighten1 Hot/Live Hot/Live Silver Dimmer / Switch/ by fully pushing it in. Check both the Dimmer  / Switch and all Please Read Before Installing 120 V 50 / 60 Hz Derating Chart into slot below push-in Remote is pressed of the Remote Dimmers / Switches. terminal. Push screwdriver in Black Black Important Notes Control Load End of Middle of while pulling wire out. Push-in 120 V Green Lighting Load 120 V Green Load Wiring Type Gang Gang terminals are for use with 50 / 60 Hz 50 / 60 Hz WARNING - To avoid the risk Ground Ground 14 AWG (1.5 mm2) solid copper • Wires shorted. Make sure the blue terminal is not grounded of entrapment, serious injury, or Incand. 500 W 400 W death, these controls must not be wire only. DO NOT use Neutral Neutral or shorted to any other wires. -6D used to control equipment which is not MLV 400 W / 300 W / stranded or twisted wire. • Wiring error. Check wiring to be sure it agrees with Dimmer Switch Remote Remote 500 VA 400 VA installation instructions and wiring diagrams. Dimmer Switch visible from every control location or which OR Use these instructions to install the could create hazardous situations such Incand. 800 W 650 W Screw Terminals: Wrap Wiring Diagram 3 • Installed in a neutral-based location. Check that neutral- model numbers listed above. For system as entrapment if operated accidentally. -10D, wire around screw terminal. based products are connected on the load side of a multi- Examples of such equipment which must -10ND 600 W / 500 W / Multi-Location Installation2 setup instructions and tools visit MLV 800 VA 650 VA Tighten securely to 5 in-lbs location installation (see Wiring Diagram 4). www.lutron.com/radiora2 not be operated by these controls include (0.55 N•m). Screw terminals -6D, -10D with RD-RD (but are not limited to) motorized gates, Lighting 6.5 A 5A are for use with 12 AWG Lamps burned out or not installed Remote Dimmer Remote Dimmer Dimmer Load Specifications: garage doors, industrial doors, microwave -8ANS (2.5 mm2) or 14 AWG • Replace or install lamps. ovens, heating pads, etc. It is the installer’s 1/4 HP 1/6 HP Motor (1.5 mm2) solid copper wire Control Load Min. Max. 5.8 A 4.4 A Dioded lamps responsibility to ensure that the equip- only. DO NOT use stranded or Brass Type Load Load Blue Brass Blue Brass Blue ment being controlled is visible from every twisted wire. • If dioded lamps are being used, replace with non-dioded Note: -8ANS controls have fins that need Hot/Live Incand. 50 W 600 W control location and that only suitable lamps. to be removed for multigang installations. -6D 1 equipment is connected to these controls. 3. W  ire controls as follows: Black Black Black 450 W / -6D, -10D, -10ND, -RD and -RS controls Green Green Green Lighting Lights turn ON Wiring MLV2 50 W / VA Failure to do so could result in serious For single location installation: See 120 V 600 VA do not have fins that need to be removed Load when Tapswitch is injury or death. 50 / 60 Hz • Wiring error. Check wiring to be sure it agrees with for multigang installations. Wiring Diagrams 1 and 2. Ground Ground Ground Incand. 50 W 1000 W Codes: Install in accordance with all local pressed, then turn installation instructions and wiring diagrams. 1 For multi-location installation: See OFF -10D and national electrical codes. Wiring Diagrams 3 and 4. Neutral MLV 2 50 W / VA 800 W / Removing Fins on -8ANS Tapswitch stuck 1000 VA Grounding: When no “grounding means” 4. P  ush all wires back into the wallbox and • Tapswitch stuck at another location. Check to see that exist within the wallbox, then the NEC® tapswitches are not sticking for all control locations in the Incand. 10 W 1000 W loosely fasten the control to the wallbox -10ND 1 2008, Article 404.9 allows a dimmer with- out a grounding connection to be installed using the control mounting screws pro- Wiring Diagram 4 circuit. MLV 2 800 W / 10 W / VA vided. Do not pinch the wires. 1000 VA as a replacement, as long as a plastic, Multi-Location Installation with Neutral2, 3 Light turns ON and Load is less than minimum load requirement noncombustible wallplate is used. For 5. A  ttach the Lutron Claro or Satin Colors -10ND with RD-RD, and -8ANS with RD-RS OFF continuously Lighting 10 W / VA 8A Control Location for Ganging • Make sure the connected load meets the appropriate this type of installation, cap or remove the -8ANS 3 Do Not remove outside fins on wallplate adapter and wallplate. minimum load requirement for that control. See Load 1/4 HP green ground wire on the dimmer and use Remote Dimmer/Switch Remote Dimmer/Switch Dimmer / Switch Motor 0.08 A 5.8 A an appropriate wallplate such as Lutron’s Controls at the end of gang a. Install wallplate adapter onto front of Specifications. Claro® or Satin Colors® wallplates. control(s). Lights don’t switch Improper programming -RD See Dimmer 8.3 A Brass Blue Brass Blue Brass Blue Neutral Wire: -10ND and -8ANS require b. T  ighten control mounting screws until Silver ON/OFF from a • Program according to the system Setup Guide. Hot/Live -RS See Switch 8.3 A a neutral wire connection in the wallbox wallplate adapter is flush to wall (do Keypad where the Dimmer/Switch is to be installed. Black Black Black Out of RF range not over-tighten). Green Green Green 1D  immer Load Type: -6D, -10D and -10ND are If a neutral wire connection is not available 120 V Load • Reposition to be within 30 feet (9 m) of an RF Signal designed for use with permanently installed in the wallbox, contact a licensed electri- c. S  nap wallplate onto wallplate adapter, 50 / 60 Hz Ground Ground Ground Repeater. incandescent, magnetic low-voltage, or tung- cian for installation. and verify that control is aligned prop- sten halogen only. Do not install dimmers to Each control Control at middle erly. Wiring control receptacles or motor-operated appli- Environment: Ambient operating tempera- has inside of Gang has all fins Neutral ances. ture: 32 °F to 104 °F (0 °C to 40 °C), d. If controls are misaligned, loosen • Wires shorted. Make sure the blue terminal is not grounded fins removed removed 1W  hen using controls in single location installations, tighten the blue terminal without 0% to 90% humidity, non-condensing. or shorted to any other wires. mounting screws appropriately. 2L  ow-Voltage Applications: Use -6D, Indoor use only. any wires attached. Do not connect the blue terminal to any other wiring or to • Wiring error. Check wiring to be sure it agrees with -10D and -10ND with magnetic (core and coil) 6. R  estore power. Verify correct local ground. low-voltage transformers only. Not for use with Spacing: If mounting one control above Installation operation (see Dimmer Operation and installation instructions and wiring diagrams. electronic (solid-state) low-voltage transformers. another, leave at least 4 ½ in (114 mm) ver- WARNING - To avoid the risk of 2U Switch Operation).  p to 9 Remote Dimmers / Switches may be connected to a Dimmer / Switch. Total blue Wallplate is warm Solid-state control dissipation tical space between them. 3S  witch Load Type: -8ANS is designed for electric shock locate and remove terminal wire length may be up to 250 ft (76 m). • Solid-state dimmers and switches internally dissipate about use with permanently installed incandescent, Wallplates: Lutron® Claro and Satin Colors fuse or lock circuit breaker in the wallplates are recommended for best color 2% of the total connected load. It is normal for dimmers and magnetic low-voltage, electronic low-voltage, match and aesthetic appearance. Do not OFF position before proceeding. Wiring Mounting Diagram 3N  eutral wire Dimmers / Switches must be connected on the Load side of a multi-location switches to feel warm to the touch during operation. or fluorescent loads and with motor loads up to with power ON could result in serious 1/4 HP (5.8 A). paint controls or wallplates. installation. injury or death. Control Cleaning: To clean, wipe with a clean Adapter damp cloth. Do not use any chemical Short Circuit Check: Check the Mounting Mounting cleaning solutions. installation for short circuits before Screws Screws installing control(s). With power OFF, install Dimmer Operation Switch Operation Wallboxes: Lutron recommends using standard mechanical switch(es) between 3 ½ in (89 mm) deep wallboxes for eas- Status LEDs (Dimmer Only) Status LED (Switch Only) ier installation. Several controls may be Hot and load. Restore power. If lights do Indicate light level; glows softly as Indicates light status; glows softly installed in one multigang wallbox — see not work or a breaker trips, check wiring. night light when load is off as night light when load is off Correct wiring and check again. Install Wallbox Derating Chart. Tapswitch Remote Dimmers / Switches: Use only control(s) only when short is no longer Included: Control Tap on/off Wallplate Lutron Maestro Remote Dimmers (-RD) present. Warranty is void if control is Dimming Rocker Tapswitch Wire Connector (1) Adapter Wallplate Tap on/off with -6D, -10D, and -10ND controls. Use turned ON with a shorted circuit. Press to Brighten Wallplate adapter and only Lutron Maestro Remote Switches 1. T  urn power OFF at fusebox or circuit wallplate purchased Press to Dim (-RS) with -8ANS controls. Up to 9 -RD or breaker. Mounting Screws (2) separately. -RS controls may be used with Maestro Dimmers or Switches. Mechanical 3- or 2. P  repare wires. When making wire con- 4-way switches will not work nections, follow the recommended strip FASSTM FASS Front Front RF Device Placement: RF Dimmers and lengths and combinations for the sup- Accessible Accessible Switches must be located within 30 feet plied wire connector. Service Service (9 m) of an RF Signal Repeater. Remote Note: Wire connector provided is suit- Switch Switch Dimmers and Switches are not required to able for copper wire only. be within a specific range of a repeater. Wire Connector: For systems with an RF signal repeater, RF • Strip insulation 3/8 in (10 mm) for Lamp Replacement Returning Devices to Factory Settings Dimmers or Switches cannot be controlled 14 AWG (1.5 mm2) or 12 AWG by the system until they are programmed Note: Returning a control to its Factory Settings will remove the control from the system *Typical Power Consumption test conditions: (2.5 mm2) wire WARNING - Shock Hazard - For any procedure other than routine lamp and erase all programming. in a system according to the system Setup • Strip insulation 7/16 in Dimmer: load is off, nightlight mode enabled. Guide. replacement, power must be disconnected at the main electrical panel. Working (11 mm) for 18 AWG (0.75 mm2) Step 1 : Triple tap the tapswitch on the control. DO NOT release after the third tap. Switch: load is off, nightlight mode enabled. with power ON could result in serious injury or even death. Remote Dimmer / Switch: load is off. wire Step 2 : Keep the tapswitch pressed on the third tap (for approximately 3 seconds) until • Use to join one or two 14 AWG Twist wire the status LEDs start to scroll up and down quickly. (1.5 mm2) or 12 AWG (2.5 mm2) connector Step 3 : Release the tapswitch and immediately triple tap the tapswitch again. The status wires with one 18 AWG For your safety during routine lamp replacement, remove power from the fixture(s) tight. LEDs will scroll up and down slowly. Technical Assistance: (0.75 mm2) ground wire. by pulling the FASS switch out on both the Dimmer / Switch and all Remote U.S.A. / Canada: 1.800.523.9466 Dimmers / Switches. The control has now been returned to Factory Settings. Mexico: +1.888.235.2910 Warranty: For warranty information, please see the enclosed Warranty, or visit Other Countries: +1.610.282.3800 www.lutron.com/resiinfo. 24 hours a day, 7 days a week. Lutron Elec­tron­ics Co., Inc. These products may be covered under one or more of the following U.S. patents: 4,992,709; 5,248,919; 5,399,940; 5,637,930; 5,798,581; 5,838,226; 5,848,054; 5,905,442; 5,982,103; 6,169,377; 6,687,487; 6,803,728; 6,969,959; 7,071,634; 7,166,970; 7,190,125; 7,362,285; 7200 Suter Road 7,365,282; 7,382,100; 7,408,525; 7,548,216 and corresponding foreign patents. U.S. and foreign patents pending. NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts. Lutron, Claro, Satin Colors, Maestro, RadioRA and the Coopersburg, PA 18036-1299 sunburst logo are registered trademarks and RadioRA 2 and FASS are trademarks of Lutron Electronics Co., Inc. Made and print­ed in the U.S.A. 7 / 09 P/N 044-157 Rev. A ©2009 Lutron Electronics Co., Inc.


Document Created: 2009-09-25 08:11:02
Document Modified: 2009-09-25 08:11:02
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC