User Manual 6

FCC ID: JPZ0062

Users Manual

Download: PDF
FCCID_1175468

English Multigang Installations Wiring Diagram 1 Wiring Diagram 2 Troubleshooting Guide In multigang installations, several controls Trim or strip wallbox wires to the length indi- Single Location Installation Designer-Style RF Maestro® Single Location Installation with Neutral are grouped horizontally in one multigang cated by the strip gauge on the back of the Symptom Probable Cause and Action Dimmers: SRD-6D, SRD-10D, SRD-10ND -6D, -10D -10ND, -8ANS, -2ANF wallbox. control. Switch: SRD-8ANS Dimmer / Switch / Fan No lights at all or no Power not present Fan Speed Control: SRD-2ANF When combining controls in a wallbox, Push-In Terminals: Insert Dimmer Speed Control fan response • Circuit breaker OFF or tripped. Perform Short Circuit Check. Remote Dimmer: SD-RD derating is required; however, no derat- wires fully. To release wire, Installation Instructions ing is required for Fan Speed or Remote Brass Blue Brass Blue • FASS is in the OFF position. Move FASS to the ON posi- Remote Switch: SD-RS insert small, flat screwdriver Tighten1 Silver Tighten1 Please Read Before Installing 120 V 50 / 60 Hz Dimmers / Switches. Hot/Live Hot/Live tion by fully pushing it in. Check both the Dimmer / Fan into slot below push-in ter- Derating Chart Black Black Control / Switch and all of the Remote Dimmers / Switches. Important Notes minal. Push screwdriver in 120 V Green Lighting 120 V Green Load Control Load End of Middle of while pulling wire out. Push-in 50 / 60 Hz Load 50 / 60 Hz Wiring WARNING - To avoid the risk Ground Ground of entrapment, serious injury, or Type Gang Gang terminals are for use with • Wires shorted. Make sure the blue terminal is not grounded death, these controls must not be 14 AWG (1.5 mm2) solid cop- or shorted to any other wires. Incand. 500 W 400 W Neutral Neutral used to control equipment which is not SRD-6D per wire only. DO NOT use • Wiring error. Check wiring to be sure it agrees with installa- Dimmer Switch Fan Speed Remote Remote visible from every control location or which 400 W / 300 W / tion instructions and wiring diagrams. Control Dimmer Switch MLV 500 VA 400 VA stranded or twisted wire. For Installation Guides, System Setup Guide and could create hazardous situations such OR Wiring Diagram 3 Lamps burned out or not installed Setup tools visit http://www.lutron.com/radiorasr. as entrapment if operated accidentally. Incand. 800 W 650 W Examples of such equipment which must Screw Terminals: Wrap • Replace or install lamps. Load Specifications: SRD-10D, Multi-Location Installation2 not be operated by these controls include SRD-10ND MLV 600 W / 500 W / wire around screw terminal. -6D, -10D with SD-RD Control Load Min. Max. (but are not limited to) motorized gates, 800 VA 650 VA Tighten securely to 5 in-lbs Dioded lamps Type Load Load garage doors, industrial doors, microwave Lighting 6.5 A 5A (0.55 N•m). Screw terminals Remote Dimmer Remote Dimmer Dimmer • If dioded lamps are being used, replace with non-dioded ovens, heating pads, etc. It is the installer’s are for use with solid cop- lamps. Incand. 50 W 600 W SRD-8ANS responsibility to ensure that the equip- 1/4 HP 1/6 HP Motor per wire only. DO NOT use SRD-6D1 ment being controlled is visible from every 5.8 A 4.4 A Brass Blue Brass Blue Brass Blue Fan setting 2 450 W / MLV 50 W / VA stranded or twisted wire. 600 VA control location and that only suitable Hot/Live • Make sure the fan is set to its highest speed using the pull- equipment is connected to these controls. Note: -8ANS controls have fins that need Black Black Black chain. Incand. 50 W 1000 W to be removed for multigang installations. 3. W  ire controls as follows: Green Green Green Failure to do so could result in serious 120 V Lighting SRD-10D1 injury or death. -6D, -10D, -10ND, -2ANF, -RD and -RS Single location installation: See Wiring Load Fan Speed Control Wrong Load Type 2 800 W / 50 / 60 Hz MLV 50 W / VA controls do not have fins that need to be Diagrams 1 and 2. Ground Ground Ground 1000 VA • Make sure that only a single ceiling paddle fan (permanent Codes: Install in accordance with all local removed for multigang installations. Multi-location installation: See Wiring and national electrical codes. split-capacitor motor) rated at 2 A or less is connected to Incand. 10 W 1000 W Neutral Removing Fins on -8ANS Diagrams 3 and 4. the control. SRD-10ND1 Grounding: When no “grounding means” 800 W / 4. P  ush all wires back into the wallbox and • Make sure that no lighting load (i.e. light kit) is connected to MLV2 10 W / VA exist within the wallbox, then the NEC® 1000 VA 2008, Article 404-9 allows a dimmer with- loosely fasten the control to the wallbox the control. Lighting 10 W / VA 8A out a grounding connection to be installed using the control mounting screws pro- Wiring Diagram 4 Lights / fan turn ON Wiring SRD-8ANS3 1/4 HP as a replacement, as long as a plastic, vided. Do not pinch the wires. Multi-Location Installation with Neutral2, 3 when Tapswitch is Motor 0.083 A noncombustible wallplate is used. For • Wiring error. Check wiring to be sure it agrees with installa- 5.8 A 5. A  ttach Lutron Claro or Satin Colors wall- -10ND, SD-RD, -2ANF -8ANS with SD-RS pressed, then turn tion instructions and wiring diagrams. this type of installation, cap or remove the Control Location for Ganging plate adapter and wallplate. OFF SRD-2ANF 4 Ceiling 0.083 A 2A green ground wire on the dimmer and use Do Not remove outside fins on Remote Dimmer/Switch Remote Dimmer/Switch Dimmer / Switch Tapswitch stuck Fan an appropriate wallplate such as Lutron’s Controls at the end of gang a. Install wallplate adapter onto front of Claro® or Satin Colors® wallplates. • Tapswitch stuck at another location. Check to see that SD-RD See Dimmer/Fan 8.3 A control(s). tapswitches are not sticking for all control locations in the Brass Blue Brass Blue Brass Blue Speed Control Neutral Wire: -10ND, -8ANS, and -2ANF b. T  ighten control mounting screws until Hot/Live Silver circuit. require a neutral wire connection in the SD-RS See Switch 8.3 A wallplate adapter is flush to wall (do wallbox where the Dimmer/Switch / Fan Black Black Black Light turns ON and Load is less than minimum load requirement Speed Control is to be installed. If a neu- not over-tighten). Green Green Green 1D  immer Load Type: -6D, -10D and -10ND are 120 V Load OFF continuously • Make sure the connected load meets the appropriate designed for use with permanently installed tral wire connection is not available in the c. S  nap wallplate onto wallplate adapter, 50 / 60 Hz Ground Ground Ground minimum load requirement for that control. See Load wallbox, contact a licensed electrician for and verify that control is aligned prop- incandescent, magnetic low-voltage, or tung- Specifications. sten halogen only. Do not install dimmers to installation. Each control Control at middle erly. Neutral control receptacles or motor-operated appli- Environment: Ambient operating tempera- has inside of Gang has all fins Lights / fan don’t Wiring fins removed removed d. If control(s) is(are) misaligned, loosen 1W switch ON / OFF ances. ture: 32 °F to 104 °F (0 °C to 40 °C),  hen using controls in single location installations, tighten the blue terminal. • Wires shorted. Make sure the blue terminal is not grounded 0% to 90% humidity, non-condensing. mounting screws appropriately. when Tapswitch on 2 Low-Voltage Applications: Use -6D, Do not connect the blue terminal to any other wiring or to ground. or shorted to any other wires. -10D and -10ND with magnetic (core and coil) Indoor use only. 6. R  estore power. Check for correct local Dimmer / Switch / • Wiring error. Check wiring to be sure it agrees with installa- low-voltage transformers only. Not for use with Spacing: If mounting one control above operation (see Dimmer / Fan Operation 2U  p to 9 RadioRA-SR Remote Dimmers / Switches may be connected to the RadioRA-SR Fan Speed Control/ electronic (solid-state) low-voltage transformers. another, leave at least 4 1⁄2 in (114 mm) ver- Installation and Switch Operation). Dimmer / Switch. Total blue terminal wire length may be up to 250 ft (76 m). Remote is pressed tion instructions and wiring diagrams. WARNING - To avoid the risk of • Neutral-based product installation location. Check that Operation of a low-voltage circuit with lamps tical space between them. inoperative or removed may result in trans- electric shock locate and remove neutral-based products are connected on the load side of a Wallplates: Lutron® Claro and Satin Colors multi-location installation (see Wiring Diagram 4). former overheating and premature failure. Lutron wallplates are recommended for best color fuse or lock circuit breaker in the Mounting Diagram 3N  eutral wire Dimmers / Switches / Fan Speed Controls must be connected on the Load strongly recommends the following: OFF position before proceeding. Wiring side of a multi-location installation. Lights / fan don’t Improper programming match and aesthetic appearance. Do not •D  o not operate low-voltage circuits without paint controls or wallplates. with power ON could result in serious switch ON/OFF from Control Adapter • Program according to the RadioRA-SR Setup Guide. operative lamps in place. injury or death. Keypad Cleaning: To clean, wipe with a clean Mounting Mounting •R  eplace burned-out lamps as quickly as Short Circuit Check: Check the instal- Screws Out of RF range damp cloth. Do not use any chemical Screws possible. cleaning solutions. lation for short circuits before installing Dimmer / Fan Operation Switch Operation • Reposition to be within 30 feet (9 m) of controling keypad. •U  se transformers that incorporate thermal Wallboxes: Lutron recommends using control(s). With power OFF, install standard Wiring protection or fused transformer primary Status LEDs (Dimmer / Fan Speed Status LED (Switch Only) 31⁄2 in (89 mm) deep wallboxes for eas- mechanical switch(es) between Hot and Only) windings to prevent transformer failure due Indicates light status; glows softly • Wires shorted. Make sure the blue terminal is not grounded to overcurrent. ier installation. Several controls may be load. Restore power. If lights or fan do Indicate light / speed level; glow as night light when light is off or shorted to any other wires. installed in one multigang wallbox — see not work or a breaker trips, check wiring. Wallbox softly as night light when load is off 3 Switch Load Type: -8ANS is designed for Tapswitch • Wiring error. Check wiring to be sure it agrees with installa- Derating Chart. Correct wiring and check again. Install Included: use with permanently installed incandescent, Control Wallplate Tap on/off tion instructions and wiring diagrams. magnetic low-voltage, electronic low-voltage, Remote Dimmers / Switches: Use only control(s) only when short is no longer Adapter Wallplate Dimming Rocker Tapswitch Lutron RadioRA®-SR Maestro Remote Wire Connector (1) Tap on/off Wallplate is warm Solid-state control dissipation or fluorescent loads and with motor loads up to present. Warranty is void if control is Press to Brighten / Increase Dimmers (-RD) with -6D, -10D, -10ND, Speed 1/4 HP (5.8 A). turned ON with a shorted circuit. Wallplate adapter and wall- • Solid-state dimmers, switches, and fan controls internally and -2ANF controls. Use only Lutron Press to Dim / Decrease 4 Ceiling Fan Application (SRD-2ANF): Mounting Screws (2) plate purchased separately. dissipate about 2% of the total connected load. It is normal RadioRA-SR Maestro Remote Switches 1. T  urn power OFF at fusebox or circuit Speed DO: for dimmers, switches, and fan controls to feel warm to the (-RS) with -8ANS controls. Up to 9 -RD or breaker. •U  se to control one paddle-type ceiling fan touch during operation. (permanent split-capacitor). -RS controls may be used with a RadioRA- 2. P  repare wires. When making wire con- FASSTM FASS • Use the ceiling fan’s pull chain to set its SR Maestro Dimmer, Switch, or Fan Speed nections, follow the recommended strip Front Front Control is buzzing or It is normal for dimmers, switches, and fan controls to emit a Control. Mechanical 3- or 4-way switches Accessible Accessible speed to the highest setting. lengths and combinations for the sup- Service Service humming slight buzzing or humming sound. will not work. Switch Switch DO NOT: plied wire connector. Note: Wire con- • Do not use to control fans that use shaded- RF Device Placement: RF Dimmers, nector provided is suitable for copper pole motors (i.e. bath exhaust fans). Switches, and Fan Speed Controls must wire only. • Do not use to control fans that have inte- be located within 30 feet (9 m) of con- grated fan speed controls (i.e. fans that have trolling keypads. Remote Dimmers and Wire Connector: • Strip insulation 3/8 in (10 mm) for Lamp Replacement Returning Devices to Factory Settings a remote control), unless the integrated con- Switches are not required to be within a Note: Returning a control to its Factory Settings will remove the control from the system 14 AWG or 12 AWG (1.0 mm2 or WARNING - For any procedure other than routine lamp replacement, power must trol is removed from the ceiling fan. specific range of controlling keypads. and erase all programming. 2.5 mm2) wire • Do not connect to any other motor-operated RF Dimmers, Switches or Fan Speed be disconnected at the main electrical panel. Working with power ON could result • Strip insulation 7/16 in Step 1 : Triple tap the main button on the control. DO NOT release after the third tap. appliance or to any lighting load type. Controls cannot be controlled by the (11 mm) for 18 AWG (0.75 mm2) in serious injury or even death. • Do not use to control a fan lighting load (i.e. Step 2 : Keep the button pressed on the third tap (for approximately 3 seconds) until the system until they are programmed in a wire status LEDs start to scroll up and down quickly. light kit). RadioRA-SR system according to the • Use to join one or two 14 AWG Twist wire Step 3 : Release the button and immediately triple tap the button again. The status LEDs RadioRA-SR Setup Guide. or 12 AWG (1.5 mm2 or connector For routine lamp replacement, remove power from the fixture(s) by pulling the FASS switch 2.5 mm2) wires with one will scroll up and down slowly. Technical Assistance: tight. out on both the Dimmer / Switch and all Remote Dimmers / Switches. USA / CAN: 1.800.523.9466 18 AWG (0.75 mm2) control The control has now been returned to Factory Settings. wire. Mexico: +1.888.235.2910 Warranty: For Warranty information, please see the enclosed Warranty, Other Countries: +1.610.282.3800 or visit www.lutron.com/resiinfo. 24 hours a day, 7 days a week. Lutron Elec­tron­ics Co., Inc. These products may be covered under one or more of the following U.S. patents: 4,992,709; 5,248,919; 5,399,940; 5,637,930; 5,798,581; 5,838,226; 5,848,054; 5,905,442; 5,982,103; 6,169,377; 6,687,487; 6,803,728; 7,071,634; 7,166,970; 7,362, 285; 7,365,282; 7200 Suter Road 7,382,100; 7,408,525 and corresponding foreign patents. U.S. and foreign patents pending. NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts. Lutron, Claro, Satin Colors, Maestro, RadioRA and the sunburst logo are regis- Coopersburg, PA 18036-1299 tered trademarks and FASS is a trademark of Lutron Electronics Co., Inc. Made and print­ed in the U.S.A. 5 / 09 P/N 044-148 Rev. B ©2009 Lutron Electronics Co., Inc.


Document Created: 2009-09-25 08:11:56
Document Modified: 2009-09-25 08:11:56
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC