User Manual 5

FCC ID: JPZ0062

Users Manual

Download: PDF
FCCID_1175467

English Español Français Português Designer-Style RF Maestro® Multigang Installations Wiring Diagram 1 Wiring Diagram 2 Troubleshooting Guide Dimmers In multigang installations, several controls Trim or strip wallbox wires to the length indi- Single Location Installation Single Location Installation with Neutral HRD-6D, HRD-6ND, HRD-10D, HRD-10ND are grouped horizontally in one multigang cated by the strip gauge on the back of the -6D, -10D -6ND, -10ND, -2ANF, -8ANS Symptom Cause and Action Switch wallbox. control. HRD-8ANS Push-In Terminals: Insert Dimmer/Switch Dimmer / Switch / No lights at all or Power not present When combining controls in a wallbox, Fan Speed Control no fan response Fan Speed Control derating is required; however, no derat- wires fully. Push-in terminals • Circuit breaker OFF or tripped. Perform Short Circuit Installation Instructions HRD-2ANF Brass Blue Brass Blue Check. ing is required for Fan Speed Controls or are for use with 14 AWG Tighten1 Silver Tighten1 Please Read Before Installing 120 V 50 / 60 Hz Remotes. Hot/Live Hot/Live • FASS is in the OFF position. Move FASS to the (1.5 mm2) solid copper wire Derating Chart Black Black ON position by fully pushing it in. Check both the Important Notes only. DO NOT use stranded or twisted wire. 120 V Green Lighting Load 120 V Green Load Dimmer / Fan Control / Switch and all of the Remote Control Load End of Middle of OR 50 / 60 Hz 50 / 60 Hz Dimmers / Switches. Codes: Install in accordance with all local Type Gang Gang Ground Ground and national electrical codes. Screw Terminals: Tighten Incand. 500 W 400 W securely to 5 in-lbs Neutral Neutral Wiring WARNING - These controls must not be used to control equipment which is HRD-6D, (0.55 N•m). Screw terminals • Wires shorted. Make sure the blue terminal is not HRD-6ND 400 W / 300 W / not visible from every control loca- MLV 500 VA 400 VA are for use with solid cop- grounded or shorted to any other wires. tion. They must also not be used per wire only. DO NOT use Wiring Diagram 3 • Wiring error. Check wiring to be sure it agrees with Dimmer Switch Fan Speed Control to control equipment which could create Incand. 800 W 650 W installation instructions and wiring diagrams. HRD-10D, stranded or twisted wire. hazardous situations such as entrapment Multi-Location Installation2 HRD-10ND 600 W / 500 W / Load Specifications: if operated accidentally. Examples of such MLV 800 VA 650 VA -6D, -10D with HD-RD Lamps burned out or not installed equipment which must not be operated 3. W  ire controls as follows: Remote Dimmer Remote Dimmer Dimmer • Replace or install lamps. Control Load Min. Max. by these controls include (but are not Lighting 6.5 A 5A Type Load Load HRD-8ANS Single location installation: See Wiring limited to) motorized gates, garage doors, Dioded lamps Motor 5.8 A 5A Diagrams 1 and 2. Incand. 50 W 600 W industrial doors, microwave ovens, heating Multi-location installation: See Wiring Brass Blue Brass Blue Brass Blue • If dioded lamps are being used, replace with non-dioded HRD-6D1 pads, etc. It is the installer’s responsibility HRD-2ANF Ceiling 2A 2A lamps. 450 W / Fan Diagrams 3 and 4. Hot/Live MLV2 50 W / VA to ensure that the equipment being con- 600 VA trolled is visible from every control location Power Booster and Interfaces: When Black Black Black Fan setting Green Green Green Incand. 50 W 1000 W and that only suitable equipment is con- Note: -8ANS controls have fins that need using power boosters or interfaces, see 120 V Lighting • Make sure the fan is set to its highest speed using the Load nected to these controls. to be removed for multigang installations. Wiring Diagrams in the HomeWorks 50 / 60 Hz pull-chain. HRD-10D1 -6D, -6ND, -10D, -10ND, and -2ANF Ground Ground Ground 800 W / Technical Reference Guide (P/N 366- MLV2 50 W / VA Environment: Ambient operating tempera- 1000 VA controls do not have fins that need to be 963). Neutral Fan Speed Control Wrong Load Type ture: 32 °F to 104 °F (0 °C to 40 °C), removed for multigang installations. Incand. 10 W 600 W 0% to 90% humidity, non-condensing. 4. P  ush all wires back into the wallbox and • Make sure that only a single ceiling paddle fan (perma- HRD-6ND1 Indoor use only. Removing Fins nent split-capacitor motor) rated at 2 A or less is con- 450 W / loosely fasten the control to the wallbox MLV2 10 W / VA nected to the control. 600 VA Spacing: If mounting one control above using the control mounting screws pro- Wiring Diagram 4 • Make sure that no lighting load (i.e. light kit) is con- another, leave at least 4 1⁄2 in. (114 mm) vided. Do not pinch the wires. Incand. 10 W 1000 W nected to the control. vertical space between them. Multi-Location Installation with Neutral2, 3 HRD-10ND1 5. A  ttach Lutron Claro or Satin Colors wall- -6ND, -10ND, -2ANF with HD-RD, -8ANS with HD-RS 2 800 W / Wallplates: Lutron Claro® and Satin Control Location for Ganging Lights / fan turn ON Wiring MLV 10 W / VA plate adapter and wallplate. 1000 VA Dimmer / Switch / Colors® wallplates are recommended for Do Not remove outside fins on Remote Dimmer/Switch Remote Dimmer/Switch Fan Speed Control when Tapswitch is • Wiring error. Check wiring to be sure it agrees with Lighting 10 W / VA 8A best color match and aesthetic appear- End of Gang Controls a. Install wallplate adapter onto front of pressed, then turn installation instructions and wiring diagrams. HRD-8ANS3 ance. Do not paint controls or wallplates. control(s). OFF 1/4 HP Motor 0.083 A 5.8 A Cleaning: To clean, wipe with a clean b. T  ighten control mounting screws until Brass Blue Brass Blue Brass Blue Tapswitch stuck Silver damp cloth. Do not use any chemical wallplate adapter is flush to wall (do Hot/Live • Tapswitch stuck at another location. Check to see that HRD-2ANF 4 Ceiling 0.083 A 2A cleaning solutions. not over-tighten). Black Black Black tapswitches are not sticking for all control locations in Fan Green Green Green Wallboxes: Lutron recommends using 120 V Load the circuit. c. S  nap wallplate onto wallplate adapter, 1D  immer Load Type: -6D, -6ND, -10D and 31⁄2 in. (89 mm) deep wallboxes for eas- 50 / 60 Hz ier installation. Several controls may be and verify that control is aligned Ground Ground Ground Light turns ON and Load is less than minimum load requirement -10ND are designed for use with permanently properly. OFF continuously installed incandescent, magnetic low-voltage, installed in one multigang wallbox — see Each control Middle of Gang Neutral • Make sure the connected load meets the appropriate or tungsten halogen only. Do not install dim- Derating Chart. has inside Control has all fins d. If control(s) is(are) misaligned, loosen minimum load requirement for that control. See Load mers to control receptacles or motor-operated Remotes: Use only Lutron HomeWorks fins removed removed mounting screws appropriately. 1W  hen using controls in single location installations, tighten the blue terminal. Specifications. appliances. Maestro Remote Dimmers (HD-RD) with Do not connect the blue terminal to any other wiring or to ground. 6. R  estore power. Check for correct local Lights / fan don’t Wiring 2 Low-Voltage Applications: Use -6D, -6D, -6ND, -10D, -10ND, and -2ANF controls. Use only Lutron HomeWorks Installation operation (see Dimmer / Fan Operation 2U switch ON / OFF • Wires shorted. Make sure the blue terminal is not -6ND, -10D and -10ND with magnetic (core  p to 9 HomeWorks Maestro Remote Dimmers / Switches may be connected to the when Tapswitch on Maestro Remote Switches (HD-RS) with and Switch Operation). grounded or shorted to any other wires. and coil) low-voltage transformers only. Not WARNING - Locate and remove HomeWorks RF Maestro Dimmer / Switch / Fan Speed Control. Total blue terminal wire -8ANS controls. Up to 9 HD-RD or HD-RS Dimmer / Switch / • Wiring error. Check wiring to be sure it agrees with for use with electronic (solid-state) low-voltage length may be up to 250 ft. (76 m). controls may be used with a HomeWorks fuse or lock circuit breaker in the Fan Speed Control/ transformers. To control electronic low-voltage installation instructions and wiring diagrams. RF Maestro Dimmer, Switch, or Fan Speed OFF position before proceeding. 3N Remote is pressed transformers, use the HRD-5NE control.  eutral wire Dimmers / Switches / Fan Speed Controls must be connected on the Load • Neutral-based product installation location. Check that Control. Mechanical 3- or 4-way switches Wiring with power ON may result in per- side of a multi-location installation. neutral-based products are connected on the load side will not work. sonal injury or death. Operation of a low-voltage circuit with lamps Mounting Diagram of a multi-location installation (see Wiring Diagram 4). inoperative or removed may result in transform- RF Device Placement: RF Dimmers, er overheating and premature failure. Lutron Switches, and Fan Speed Controls must Short Circuit Check: Check the instal- Wallplate Lights / fan don’t Improper programming lation for short circuits before installing Control switch ON/OFF strongly recommends the following: be located within 30 feet (9 m) of an RF control(s). With power OFF, install stan- Mounting Adapter Dimmer / Fan Operation Switch Operation • Check programming in the HomeWorks software. •D  o not operate low-voltage circuits without Signal Repeater or an RF Processor. Mounting from Keypad Screws Out of RF range operative lamps in place. Remote Dimmers and Switches are not dard mechanical switch(es) between Hot Screws Status LEDs Status LED •R  eplace burned-out lamps as quickly as required to be within a specific range of a and load. Restore power. If lights or fan Indicates light / speed level; glow Indicates light status; glows softly • Reposition RF Signal Repeater or RF Processor to be possible. repeater or processor. do not work or a breaker trips, check softly as night light when load is off as night light when light is off within 30 feet (9 m) of control. •U  se transformers that incorporate thermal RF Dimmers, Switches or Fan Speed wiring. Correct wiring and check again. Tapswitch protection or fused transformer primary Controls cannot be controlled by the Install control(s) only when short is no lon- Tap on/off Wiring Wallbox windings to prevent transformer failure due system until they are addressed and pro- ger present. Warranty is void if control is Dimming Rocker Tapswitch • Wires shorted. Make sure the blue terminal is not to overcurrent. grammed. See the HomeWorks Software turned ON with a shorted circuit. Included: Control Press to Brighten / Increase Tap on/off grounded or shorted to any other wires. online help. Speed 3 Switch Load Type: -8ANS is designed for use • Wiring error. Check wiring to be sure it agrees with with all permanently installed lighting loads and 1. T  urn power OFF at fusebox or circuit Wire Connector (1) Press to Dim / Decrease installation instructions and wiring diagrams. Wallplate/Adapter purchased Speed with motor loads up to 1/4 HP (5.8 A). breaker. separately. 4 Ceiling Fan Application (HRD-2ANF): 2. P  repare wires. When making wire con- Mounting Screws (2) Wallplate is warm Solid-state control dissipation DO: nections, follow the recommended strip FASSTM FASS • Solid-state dimmers, switches, and fan controls inter- •U  se to control one paddle-type ceiling fan Front Front lengths and combinations for the sup- Accessible Accessible nally dissipate about 2% of the total connected load. It (permanent split-capacitor)*. Service Service is normal for dimmers, switches, and fan controls to feel • Use the ceiling fan’s pull chain to set its plied wire connector. Note: Wire con- nectors provided are suitable for copper Switch Switch warm to the touch during operation. speed to the highest setting*. DO NOT: wire only. Control is buzzing It is normal for dimmers, switches, and fan controls to emit a • Do not use to control fans that use shaded- Wire Connector: or humming slight buzzing or humming sound. pole motors (i.e. bath exhaust fans)*. • Strip insulation 3/8 in. (9.5 mm) Lamp Replacement • Do not use to control fans that have inte- for 14 AWG (1.5 mm2) wire grated fan speed controls (i.e. fans that have • Strip insulation 1/2 in. WARNING - For any procedure other than routine lamp replacement, power must *N  ote: Refer to Application Note # 217—“HomeWorks® Maestro® Controls Reference a remote control), unless the integrated con- (12.7 mm) for 16 or 18 AWG be disconnected at the main electrical panel. Working with power ON may result in Guide” for advanced features of the HomeWorks Maestro controls. trol is removed from the ceiling fan*. (1.0 mm2 or 0.75 mm2) wire personal injury or death. Warranty: For Warranty information, please see the Warranty enclosed with the product, or • Do not connect to any other motor-operated • Use to join one 14 AWG Twist wire visit www.lutron.com/resiinfo. appliance or to any lighting load type. (1.5 mm2) or 12 AWG (2.5 mm2) ground wire with one connector • Do not use to control a fan lighting load (i.e. 18 AWG (0.75 mm2) tight. For routine lamp replacement, remove power from the fixture(s) by pulling the FASS switch These products may be covered under one or more of the following U.S. patents: 4,835,343; 5,248,919; light kit). control ground wire. out on both the Dimmer / Switch and all Remote Dimmers / Switches. 5,399,940; 5,637,930; 5,798,581; 5,838,226; 5,848,054; 5,905,442; 5,982,103; 6,687,487; 6,803,728; D353,798 and corresponding foreign patents. U.S. and foreign patents pending. Lutron, Claro, Satin Colors, Maestro, HomeWorks and the sunburst logo are registered trademarks and FASS and the HomeWorks logo are trademarks of Lutron Electronics Co., Inc. © 2008 Lutron Electronics Co., Inc. Lutron Elec­tron­ics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299 Made and print­ed in the U.S.A. 1 / 08 P/N 043-238 Rev. B


Document Created: 2009-09-25 08:13:51
Document Modified: 2009-09-25 08:13:51
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC