User Manual

FCC ID: JPZ0061

Users Manual

Download: PDF
FCCID_1197440

Radio Powr Savr™ Installation Instructions Please Read Before Installing English Instructions Install a Sensor in as little as 15 minutes Wireless Battery-Powered Occupancy Sensor A Pre-Installation 1.3 Perform the Sensor coverage and wireless communication tests as described in sections E. Testing Sensor Coverage and F. Testing Wireless Communication. G Permanent Mounting Methods Activity The sensitivity of the Sensor can be adjusted based on the expected level of activity 1 LRF2-OCRB-P 3 V 14 mA 434 MHz (Occupancy/Vacancy) within the room. There are three available activity settings: Low Activity, Medium LRF2-VCRB-P 3 V 14 mA 434 MHz (Vacancy Only) California Title 24 Compliant 1 Before setting up the Sensor, the corresponding dimming or switching device(s) should be installed. Refer to that product’s installation sheet for instructions. 1.4 Ifanother the Sensor does not perform satisfactorily from this location, it may be moved to Permanent Drop Ceiling Mounting Activity, and High Activity. Compatible Products location by pulling the Sensor straight down and repeating steps 1.3 and 1.4. 1.1 After the Sensor has been temporarily mounted, leave the Sensor in place on the Low Activity: This is the most sensitive setting and will detect very slight motions. For a full list of compatible products visit www.lutron.com/occsensors 2 Twist and remove mounting bracket to insert battery. tile and either take the tile down or remove an adjacent tile to gain access to the legs of the mounting wire on the back of the tile. This is the recommended setting, as it will work well for nearly all applications. It is Product Description 1.5 If the Sensor’s performance is satisfactory, it should be permanently attached to the ceiling tile, as described in section G. Permanent Mounting. ideal for spaces where occupants will often be seated for long periods of time. Lutron’s ceiling-mounted Occupancy Sensors are wireless, battery-powered, passive 1.2 Twist the wire legs together tightly so the mounting bracket Medium Activity*: This setting is slightly less sensitive than the Low Activity infrared (PIR) devices that automatically control lights via RF communication with a dimming or switching device. These Sensors detect the heat from people moving within an area to determine when the space is occupied. The Sensors then transmit the appropriate 2 Temporary Solid Ceiling Mounting remains snug against the tile. setting and can be used for spaces that experience normal activity. Use this procedure if the Sensor will be mounted on a solid, continuous ceiling surface commands to the associated dimming or switching device to turn the lights on or off High Activity*: This is the least sensitive setting and can be used for spaces that automatically, providing both convenience and exceptional energy savings. such as drywall, plaster, concrete, or wood. will generally only experience large motions, such as foot traffic. Two 3M™ Command™ adhesive strips are provided for temporarily mounting and testing the Sensor on smooth, solid ceiling surfaces. These strips are designed for easy, damage- Battery free removal and are not reusable. These strips should not be used for permanently Release mounting the Sensor (see section G. Permanent Mounting ). Carefully follow the removal * The Low Activity setting is the default and will perform best for most applications. Rarely, if the Sensor is 1.3 Tab instructions below to ensure the ceiling is not damaged during removal. placed near external noise sources such as heating vents, air conditioning vents, or light bulbs, it may turn Replace the tile. NOTE: DO NOT use the adhesive strips on ceiling tiles, as they will likely the lights on without occupancy or keep the lights on too long after vacancy. If this occurs, changing the • Easy-to-follow sensitivity to Medium Activity or High Activity should resolve the problem. B cause damage to the tile upon removal. Instructions Set-Up In order for the Sensor to operate properly, it must first be set up with a corresponding 2 Permanent Solid Ceiling Mounting Advanced Set-Up Operation dimming or switching device. The procedure for setting up a Sensor with a Maestro Wireless® (MRF2- only) Dimmer or Electronic Switch is detailed below. 2.1 Peel the red “Command Strips” liner off of one of the adhesive strips and apply the strip to the flat side of the mounting bracket as shown in the diagram. Press firmly. 2.1 Drill two 3/16 in (4.6 mm) pilot holes for the provided screw anchors. The advanced set-up is accessed by using the buttons on the back of the Sensor. If setting up a Sensor with a different device, visit www.lutron.com/occsensors or consult 2.2 Press the anchors into the holes and tap flush with a hammer. 1 To display the current setting, press and release the desired button. An LED will illuminate briefly, indicating the current setting. P/N 041-172a the installation guide for that device for the correct set-up procedure. 2.3 Place the flat side of the mounting bracket against the 2 NOTE: DO NOT cover the bracket’s screw 1 Setting up a Sensor with a Maestro Wireless Dimmer or Electronic Switch holes because they will be used to mark screw hole locations on the ceiling. ceiling and install the two provided screws using a hand screwdriver. To adjust a setting, press and hold the desired button until the LED corresponding to the current setting begins flashing rapidly, indicating the setting can now be adjusted. 1.1 Place the Dimmer or Switch in set-up mode by pressing and holding the tap button for NOTE: Leave the removal tab exposed past NOTE: Do not over-tighten. approximately 6 seconds until all LEDs on the device begin flashing. Release the tap button. the edge of the bracket so it can be accessed for removal later. 3 Each subsequent button press of less than 2 seconds will increment the mode to the next available setting. Pressing any of the other buttons will have no effect. 4 To save the selected setting, press and hold the button until the LED turns on solid, indicating the saved setting. Dimmer or Switch 2.2 Identify a location on the ceiling where the Sensor will have a good view of the room. 2.4 Attach the Sensor to the mounting bracket by inserting and twisting in a clockwise direction 5 During the adjustment procedure, if there is no activity for 30 seconds, the LEDs 1.2 Add the Sensor to the Dimmer or Switch by pressing and holding the “Lights Off” button on the front of until the Sensor locks into place. will turn off and no settings will be saved. the Sensor for approximately 6 seconds until the lens flashes briefly. The lights in the room will also flash 3 2.3 Remove the black “wall side” liner from the adhesive strip. Key Features times, indicating the Sensor has been successfully added. The Dimmer or Switch will exit set-up mode 2.4 Position the mounting bracket on the ceiling and press firmly for I Lens Masking (Optional) automatically. Whenever possible, the Sensor should be installed in a location where it cannot easily see · Low Maintenance. 10-year battery life. Convenient low-battery indicator. several seconds. into areas outside the intended space, such as hallways or adjacent rooms. If this situation · Multiple Devices. Up to 3 Sensors can work together to control lights for broader cannot be avoided, portions of the lens may be masked with the provided labels to block coverage in large spaces. Each Sensor may be added to up to 10 receiving devices. 1.3 The “Lights On” and “Lights Off” buttons should now switch the lights in the room on and off, respectively, when pressed. the Sensor’s view of the undesired areas. Sensor Operation Repeat the above procedure to set up the Sensor with any additional devices. 2.5 Attach the Sensor to the mounting bracket by inserting and twisting in a clockwise direction until the Sensor locks into place. H Advanced Set-Up (Optional) · It is recommended to remove the Sensor from the mounting bracket before applying the masking labels. Occupancy Version – The Sensor will automatically turn the lights on when the space is occupied and automatically turn the lights off after the space is vacated. 2 Setting the Occupancy Light Level (occupancy version, dimming devices only) 2.6 Perform the Sensor coverage and wireless communication tests as described in sections E. Testing Sensor Coverage and F. Testing Wireless Communication. The Sensor features several advanced set-up modes. For the majority of installations, the default settings will provide the best performance and you will not need to utilize the advanced set-up. NOTE: The Sensor can be screwed onto the mounting bracket in several different orientations. Be sure to note the Sensor’s orientation before taking it Vacancy-Only Version – The lights must be manually turned on* at the dimming or down and replace the Sensor in the same orientation to ensure the intended switching device. The Sensor will automatically turn the lights off after the space is vacated. 2.1 Set the Dimmer to the desired light level for entering the room. Removing Temporary Mounting Strip The Occupancy version of the Sensor has three adjustable advanced set-up modes: area gets blocked. * There is a built-in 15-second vacancy grace period that begins when the lights are automatically turned Timeout, Auto-On, and Sensitivity. The Vacancy-Only version has only two modes · Outer lens sections correspond to the detection regions furthest away from the off, during which the lights will automatically turn back on in response to motion. This grace period is provided as a safety and convenience feature in the event that the lights turn off while the room is still 2.2 Save the occupancy light level by pressing and holding the “Lights On” button on the front of a 2.7 Remove the Sensor from the mounting bracket by twisting (Auto-On not available). The default settings are listed below. Sensor, while inner sections correspond to regions closer to the Sensor. occupied, so that the user does not need to manually turn the lights back on. After 15 seconds, the grace Sensor that has been set up. After approximately in a counter-clockwise direction. Default Settings: · Be careful when applying the labels to avoid creating gaps between adjacent period expires and the lights must be manually turned on. 6 seconds, the lens will flash rapidly several times, If the Sensor coverage and wireless communication tests masked sections. The Sensor may detect motion through inadvertent gaps. NOTE: For either Sensor version, the lights can also be manually turned off at any time by indicating the light level has been saved. All Sensors have been successfully completed, use the mounting Timeout: 15 minutes using the dimming or switching device directly. set up with the Dimmer will now use the saved bracket as a template to mark the screw hole locations occupancy light level. with a pencil. Auto-On: Always (Occupancy version only) Timeout Auto-On Activity Timeout Auto-On Activity Activity: Low Activity Important Notes C 30 min Sensor Placement and Coverage Always 30 min 2.8 Always 15 min To remove the bracket from the ceiling, grasp the removal tab on the adhesive strip Low light 1. This Sensor is part of a system and cannot be used to control a load without a 15 min Low light 5 min Disable compatible dimming or switching device. Refer to the instruction sheets of the receiving and pull the tab VERY SLOWLY straight across the ceiling, stretching the strip until 5 min Disable Before mounting the Sensor, please note the following: device(s) for installation information. the bracket releases from the ceiling. Discard the strip. NEVER pull the strip at an • The Sensor is designed for ceiling use only. DO NOT install on ceilings higher than angle, as it may break or damage the ceiling surface. 2. Clean Sensor with a soft damp cloth only. DO NOT use any chemical cleaners. 12 ft (3.7 m) or non-ceiling surfaces. Doing so may significantly inhibit the Sensor’s P P P P U U Lens sections 3. The Sensor is intended for indoor use only. Operate between 32 °F and 104 °F performance. NOTE: Pull very slowly. NOTE: Do not pull at an angle. Advanced U L Set-Up Modes U L L L L L shown in white (0 °C and 40 °C). L L • The Sensor should be installed in a location where it has a good view of all parts are masked 4. DO NOT paint Sensor. of the room. The Sensor requires line of sight to operate properly. If you cannot Timeout with labels Lens Mask The Sensor will turn the lights off if no motion occurs for the duration of the timeout period. Lens sections 5. The range and performance of the RF system is highly dependent on a variety of see the Sensor, it cannot see you. The Sensor cannot see through glass objects There are three available timeout settings: 5, 15, and 30 minutes. shown in gray have complex factors such as: such as patio or shower doors. not been masked · Distance between system components • D  O NOT mount the Sensor within 4 ft (1.2 m) of HVAC vents or light bulbs installed Auto-On · Geometry of the building structure below the ceiling line. Warmer rooms may reduce the Sensor’s ability to detect The automatic-on functionality of the Sensor can be adjusted to control how the lights · Construction of walls separating system components respond upon initial occupancy. There are three available settings: Always, Low light, · Electrical equipment located near system components occupants. and Disable. 6. Use only high-quality lithium batteries, size CR123, 3 V (ANSI-5018LC, • The Sensor may be installed up to 60 ft (18.3 m) away from the associated dimming IEC-CR17345). DO NOT use rechargeable batteries. Using improperly rated batteries or switching device(s) if they are in direct line of sight. If there are walls or other Always: The lights will always turn on. could damage the Sensor. barriers between the Sensor and receiving device(s), the Sensor should be located Low light: The lights will only turn on automatically upon entry if there is not already CAUTION: This product must not be used to control equipment which could create hazardous situations, such as entrapment, if operated accidentally. • W within 30 ft (9.1 m).  henever possible, avoid placing the Sensor in a location where it has a broad view E Testing Sensor Coverage sufficient ambient light in the room. Disable: This setting converts the Sensor to vacancy mode. The lights will not Hallway falls within Sensor’s Examples of equipment which must not be controlled with this product include (but are not limited to) motorized gates, garage doors, industrial doors, etc. outside the intended space. If this is unavoidable, the lens can be masked to block the view of undesired areas (refer to section I. Lens Masking). 1 With the Sensor mounted on the ceiling, press and release the “Test: Sensor” button on the front of the automatically turn on but will still automatically turn off after vacancy. The lights must be manually turned on by using the associated dimming or switching device. coverage area. device. The lens will glow briefly, indicating the test NOTICE: DO NOT disassemble, crush, puncture, or incinerate the batteries. • T  he Sensor’s detection range is dependent on the ceiling height, as shown in the mode has been entered. NOTE: The 15-second vacancy grace period is active in this mode. Refer to the DO NOT dispose of batteries in normal household waste. Please recycle, take table below. Sensor Operation section at the beginning of this document for more details. to a proper battery disposal facility, or contact your local waste disposal provider regarding local restrictions on the disposal or recycling of batteries. Sensor Coverage Chart NOTE: There is a warm-up period of approximately 40 seconds after the batteries are installed before the Troubleshooting Ceiling Max. Room Dimensions Radius of Coverage test mode can be activated. If the button is pressed FCC Information Symptom Possible Causes Solution NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, Height for Complete Coverage at Floor during this time, the lens will flash continuously until pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against the warm-up period is complete, and then the test Lights do not turn ON when space is Sensor is not correctly added to dimming / switching device(s). Refer to section B. Set-Up. harmful interference in a residential installation. This equipment generates, uses and can radiate radio 8 ft (2.4 m) 18 x 18 ft (5.5 x 5.5 m) 13 ft (4.0 m) mode will be automatically entered. occupied. frequency energy and, if not installed and used in accordance with the instructions, may cause harmful Sensor’s Auto-On setting is set to “Low light” or “Disable”. Refer to section H. Advanced Set-Up. interference to radio and television reception, which can be determined by turning the equipment off and on. 9 ft (2.7 m) 20 x 20 ft (6.1 x 6.1 m) 14.5 ft (4.4 m) The lights were recently turned off manually and the timeout has For more details, refer to Frequently Asked Questions at www.lutron.com/occsensors 2 The user is encouraged to try to correct the interference by one or more of the following measures: Confirm the coverage area by walking through the space and observing the lens. not yet expired. · Reorient or relocate the receiving antenna. 10 ft (3.0 m) 22 x 22 ft (6.7 x 6.7 m) 16 ft (4.9 m) The lens will glow solid every time motion is detected. If the lens remains off during Sensor does not have full view of room. Refer to section C. Sensor Placement. · Increase the separation between the equipment and receiver. 12 ft (3.7 m) 26 x 26 ft (7.9 x 7.9 m) 19 ft (5.8 m) motion, the Sensor cannot detect motion at that location. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Sensor is outside wireless range of dimming/switching device. Refer to section C. Sensor Placement or F. Testing Wireless Communication. · Consult the dealer or an experienced radio/TV technician for help. Battery has been installed incorrectly. Refer to section A. Pre-Installation. Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could void the user’s authority to operate this equipment. D Temporary Mounting Methods 3 Press and release the “Test: Sensor” button again to exit the test mode. If the button is not pressed, the test mode will automatically time out 15 minutes after being enabled, or 5 minutes after the last detected motion if the room is vacated. Dimming/switching device has been improperly wired. Light bulb(s) burned out. Refer to the instruction sheet of the receiving device or call Lutron Technical Support Center at 1.800.523.9466. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: If you are uncertain about correctly positioning the Sensor, the following temporary Breaker is off or tripped. 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. mounting and testing procedures are recommended to verify proper performance before Lights turn OFF while space is occupied. Sensor’s timeout is too short for this application. Refer to section H. Advanced Set-Up. Technical Assistance permanently installing the Sensor. 4 If the Sensor has significant trouble detecting motion during the test, it should be moved to another location and retested. If the Sensor still has poor detection from Sensor does not have full view of room. Lens mask is improperly applied. Refer to section C. Sensor Placement. Refer to section I. Lens Masking. For questions concerning the installation or operation of this product, call the Lutron Technical Support Center. Please provide exact model number when calling. 1 Temporary Drop Ceiling Mounting the new location, refer to the Troubleshooting section. NOTE: If the Sensor is detecting motion in areas that are not desirable, such as Lights stay ON after space is vacated. Sensor’s sensitivity is too low. Sensor’s timeout has not yet expired. Refer to section H. Advanced Set-Up. Refer to section H. Advanced Set-Up. U.S.A. and Canada (24 hrs / 7 days) Use this procedure if the Sensor will be mounted on a ceiling tile. hallways or adjacent rooms, refer to section I. Lens Masking. An external noise source such as an HVAC vent is interfering. Try moving Sensor to a new location or reducing sensitivity. Refer to section C. Sensor Placement or H. 1.800.523.9466 Fax +1.610.282.6311 The ceiling tile mounting wire is provided for both temporary and permanent mounting of Advanced Set-Up. Mexico 8am – 8pm ET the Sensor to drop ceilings composed of multiple tiles. It is designed to allow temporary mounting, testing, and repositioning (if necessary) of the Sensor without damaging a 5 If Sensor detection is satisfactory during this test, perform the wireless communication test as described in section F. Testing Wireless  attery has been installed incorrectly. B Refer to section A. Pre-Installation. +1.888.235.2910 ceiling tile. Once the Sensor’s final position has been chosen, the mounting wire can be Communication. Lights turn ON when walking past room. Sensor coverage extends beyond room perimeter. Refer to section C. Sensor Placement or I. Lens Masking. Behavior of lights does not match Sensor The intended setting was not saved. Refer to section H. Advanced Set-Up. Other countries 8am – 8pm ET twisted to lock the Sensor in place permanently. settings. Multiple Sensors are added to a dimming/switching device and Refer to section H. Advanced Set-Up. +1.610.282.3800 www.lutron.com F their settings do not match. Limited Warranty 1.1 Insert the ceiling tile mounting wire Testing Wireless Communication Sensor lens does not glow in response to Sensor cannot see motion due to obstruction. Move Sensor to another location. Refer to section C. Sensor Placement. through the two smaller holes in the motion during Sensor coverage testing. Room is too big or oddly shaped. Multiple Sensors may be necessary for full room coverage. For more details, refer to Frequently Asked Questions (Valid only in U.S.A., Canada, Puerto Rico, and the Caribbean.) This test should be performed to verify that the Sensor has been correctly set up Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within one year after purchase. mounting bracket and replace the with the corresponding dimming or switching device and that there is proper at www.lutron.com/occsensors For warranty service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage mounting bracket. wireless communication from the chosen Sensor location. Battery has been installed incorrectly. Refer to section A. Pre-Installation. pre-paid. Lens does not stop glowing during Sensor An external noise source such as an HVAC vent is interfering. Try moving Sensor to a new location or reducing sensitivity. Refer to section C. Sensor Placement or H. This warranty is in lieu of all other express warranties, and the implied warranty of merchantability coverage testing even when there is no Advanced Set-Up. is limited to one year from purchase. This warranty does not cover the cost of installation, removal or reinstallation, or damage resulting from misuse, abuse, or damage from improper wiring or 1 If the lights in the room are not on, turn them ON manually at the dimming or switching device. motion. Lights do not respond correctly during Sensor is not correctly added to dimming / switching device. Refer to section B. Set-Up. installation. This warranty does not cover incidental or consequential damages. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CON­NEC­TION WITH THE MANUFACTURE, SALE, INSTALLATION, wireless communication testing. Sensor is outside wireless range of dimming/switching device. Move Sensor closer to dimming/switching device and retry test. Refer to section F. Testing Wireless DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE PUR­CHASE PRICE OF THE UNIT. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not 1.2 Mount Sensor to a ceiling tile by inserting the wire 2 Press and release the “Lights Off” button on the front of the Sensor. The Battery has been installed incorrectly. Communication. Refer to section A. Pre-Installation. allow the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty may last, legs through the tile, making sure the Sensor is lights should turn OFF. so the above limitations may not apply to you. Patents pending. Lutron, Maestro Wireless, and the Sunburst logo are registered flush to the tile. Dimming/switching device has been improperly wired. Refer to the instruction sheet of the receiving device or call Lutron Technical Support Center at 1.800.523.9466. trademarks and Radio Powr Savr is a trademark of Lutron Electronics Co., Inc. ANSI is a registered trademark of the American Light bulb(s) burned out. National Standards Institute. IEC is a trademark of the International Electrotechnical Commission. 3M and Command are trademarks of 3M Company © 2009 Lutron Electronics Co., Inc. Note: Do not twist wire legs together. 3 Press and release the “Lights On” button on the front of the Sensor. The Breaker is off or tripped. lights should turn ON. Sensor lens flashes and lights do not turn Battery is low. Replace battery. For more details, refer to Frequently Asked Questions at www.lutron.com/occsensors Lutron Electronics Co., Inc. ON when space is occupied. Sensor is in test mode. Remove sensor from test mode. Refer to section E. Testing Sensor Coverage. 7200 Suter Road If the lights do not respond correctly, Coopersburg, PA 18036-1299, U.S.A. refer to the Troubleshooting section. Made and printed in the U.S.A. 25/09/09 P/N 041-172 Rev. A


Document Created: 2009-09-25 11:20:08
Document Modified: 2009-09-25 11:20:08
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC