Users Manual

FCC ID: JPZ0040

Users Manual

Download: PDF
FCCID_735559

® W ireless Home Lighting Control RAMC-MFE, RBMC-MFE Setup and Installation Guide For a RadioRA® Multi-Function Entry Master Control A Comprehensive Step-by-Step Guide for Installing, Programming, and Operating the Lutron RadioRA® Multi-Function Entry Master Control Note: Please leave this manual with homeowner. English P/N 044-022

Notes on this Manual The procedures to setup a RadioRA® Multi-Function Entry Master Control are contained in this manual. For more information on programming the remainder of your RadioRA® System, or for advanced features, refer to the original RadioRA® Setup Guide (P/N 044-001). Important Application Note The Multi-Function Entry Master Control is a type of Master Control. The RadioRA® System can have a maximum of 12 Master Controls. Important Installation Notes 1. Install in accordance with all national and local electrical codes. 2. Do not paint the Multi-Function Entry Master Control. 3. Operate in ambient temperatures between 0°C (32°F) and 40°C (104°F). 4. Do not mount outside. Unit must not get wet. 5. Use only the AC adapter provided by Lutron with your Multi-Function Entry Master Control. Using an AC adapter not rated at the following specifications could damage the control and possibly overheat the AC adapter. • Input: AC 120V 60Hz • Output: AC 9V/500mA Class 2 6. The range and performance of the RadioRA® System is highly dependent on a variety of complex factors such as: • Distance between system components • Geometry of the home • Construction of walls separating system components • Electrical equipment located near system components Consumer Information Notice This Visor Control System, consisting of a Multi-Function Entry Master Control and a Visor Control transmitter, must only be used to operate visible means of barrier entry such as garage doors and motorized gates. Do not use this Multi-Function Entry Master Control with any garage door opener that lacks the safety stop and reverse feature as required by federal safety standards. (This includes any garage door opener model manufactured before April 1, 1982.) A garage door opener which cannot detect an object, signaling the door to stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features increases risk of serious injury or death. Warning This RadioRA® system must not be used to control equipment, other than lighting, which is not visible from every master or local control location. It also must not be used to control equipment which could create hazardous situations such as entrapment if operated accidentally. Examples of equipment which must not be controlled by this RadioRA® system when not visible from a Multi-Function Entry Master Control or local control location include (but are not limited to) motorized gates, garage doors, industrial doors, and microwave ovens, heating pads, etc. It is the installer's responsibility to ensure that the equipment, other than lighting, being controlled is visible from every master or local control location and that only suitable equipment is connected to this RadioRA® system. FCC Information NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could void the user's authority to operate this equipment. 2 RadioRA® Setup Guide for the Entry Master Control

Table of Contents Section 1 - Overview Overview Multi-Function Entry Master Control ............................................................................................. 4 Application Examples Activating a “Home” Lighting Scene ............................................................................................ 6 Controlling a Garage Door ............................................................................................................. 6 Interfacing to a Timeclock .............................................................................................................. 7 Interfacing to a Security System ................................................................................................... 7 Section 2 - Installation Installing an Entry Master Control Installation ....................................................................................................................................... 8 Section 3 - Start-Up Activating an Entry Master Control Activating Control ........................................................................................................................... 10 Button Programming Assigning a Column of Buttons as ROOMS or SCENES ............................................................ 11 Assigning Dimmers, Switches, or GRAFIK Eye® Control Units to Buttons ............................... 12 Setting Light Levels/GRAFIK Eye® Scene Selection for Buttons ............................................... 13 Configuring General CCIs as Maintained or Momentary ............................................................. 14 Entry Master Control Learning a Visor Control ............................................................................ 16 Section 4 - Advanced Features Advanced Programming Programming the ALL ON Button .................................................................................................. 18 Programming the ALL OFF Button ................................................................................................ 18 Copying Button Programming ....................................................................................................... 18 Erasing Button Programming ........................................................................................................ 18 Programming the FULL and FLASH Buttons ............................................................................... 19 Deleting ALL Visor Control Transmitters from an Entry Master Control ................................... 22 Section 5 - Troubleshooting Troubleshooting Guide ................................................................................................................. 24 Returning to Default Factory Settings Entry Master Control .......................................................................................................................25 RadioRA® Setup Guide for the Entry Master Control 3

Overview Multi-Function Entry Master Control Front View CCI Buttons Section 1 - Overview Provide a means for programming the general inputs. Also toggles the ROOM or SCENE when pressed. CCI 1 CCO Buttons Provide a contact CCI 2 closure output for as CCO 1 long as the button is ROOM or SCENE pressed. SECURITY Buttons Toggle lights ON and OFF. Works just FULL like ROOM/SCENE CCO 2 buttons on a standard FLASH RadioRA® Master Control. LEARN Button LEARN Used to enter LEARN mode. LEARN mode is used when the Multi- Function Entry Master Control is learning Visor Control Transmitter buttons. ALL OFF Button Turns all lights OFF. ALL ON Button Turns all lights ON. FULL and FLASH Buttons Provide a means for programming the security input. Also provide diagnostic capability for FULL and FLASH. Visor Control Transmitter (sold separately) • Mounts to a vehicle’s visor. • Buttons provide a means for remotely activating buttons on the Entry Master Control. • Turn on an Entry Master Control SCENE • Toggles an Entry Master Control ROOM • SECURITY FULL and FLASH • To enter, press and hold Visor Control button setup as security button for 3 seconds. • To exit, just press any button on the Visor Control. 4 RadioRA® Setup Guide for the Entry Master Control

Overview Rear View Section 1 - Overview Terminal Block Each terminal accepts 14-22 AWG, Class 2 wire. FULL FLASH CCI 1 CCI 2 COM 1 2 1 2 CCO 1 CCO 2 Use included OUTPUTS INPUTS screwdriver to secure wires into terminals. Outputs Common Provide a momentary contact Common connection for all inputs. closure output. FULL FLASH Security Input General Inputs Activates FULL and FLASH scenes Turns ON a ROOM or SCENE when while a maintained input is present. set as a momentary input; toggles a ROOM or SCENE when set as a maintained input. RadioRA® Setup Guide for the Entry Master Control 5

Overview Application Examples Activating a “Home” Lighting Scene Pressing the “Home” button on the Entry Master Control activates the “Home” lighting scene. Section 1 - Overview SUNSET HOME SUNRISE NIGHT CCO 1 1 GARAGE SECURITY AWAY FULL WELCOME CCO 2 2 GARAGE FLASH MORNING LEARN ALL ON ALL OFF – OR – Pressing the “Home” button HOME AWAY GARAGE 1 on the Visor Control activates the same “Home” lighting scene. Controlling a Garage Door Pressing the button labeled “Garage 1” closes the contact of CCO 1 to open or close the garage door. SUNSET HOME Garage Door Opener SUNRISE NIGHT CCO 1 1 GARAGE SECURITY AWAY FULL WELCOME CCO 2 2 GARAGE FLASH MORNING LEARN ALL ON ALL OFF FULL FLASH CCI 1 CCI 2 COM 1 2 1 2 CCO 1 CCO 2 OUTPUTS INPUTS HOME AWAY GARAGE 1 – OR – Pressing the “Garage 1” button on the Visor Control will also open or close the garage door. 6 RadioRA® Setup Guide for the Entry Master Control

Overview Interfacing to a Timeclock The lighting scene “Sunset” on the Entry Master Control can be activated by either pressing the button labeled “Sunset” or by an input closure on CCI 1. Section 1 - Overview 12:00 PM – OR – SUNSET HOME SUNRISE NIGHT Output 1 Output 2 CCO 1 1 GARAGE SECURITY AWAY C NO NC C NO NC FULL WELCOME CCO 2 2 GARAGE FLASH MORNING LEARN FULL FLASH CCI 1 CCI 2 COM ALL ON ALL OFF 1 2 1 2 CCO 1 CCO 2 OUTPUTS INPUTS Interfacing to a Security System SUNSET HOME Enter SECURITY Mode by CCO 1 1 GARAGE SUNRISE NIGHT pressing and holding SECURITY AWAY (approximately 3 seconds) FULL WELCOME CCO 2 2 GARAGE the “SECURITY” button on Security Panel FLASH MORNING LEARN the Visor Control. ALL ON ALL OFF Output – OR – FULL FLASH CCI 1 CCI 2 COM 1 2 1 2 HOME SECURITY GARAGE 1 CCO 1 CCO 2 OUTPUTS INPUTS Enter SECURITY Mode with a maintained input closure from a Security System. • While in SECURITY Mode, dimmers assigned to FULL will turn on to full intensity, dimmers assigned to FLASH will begin flashing. RadioRA® Setup Guide for the Entry Master Control 7

Installing an Entry Master Control Installation Read all instructions completely before installation. Step 1 Find a suitable location for the Step 3 Wiring to input and output Entry Master Control devices. External Switch Place the Entry Master Control in a convenient Closures (by customer) and accessible location. Access to input and From Security System output wiring should be considered when selecting the mounting location. Note: Entry Master Control must be located From Input Device 1 Section 2 - Installation within 30 feet of a Repeater. For optimum Visor Control range, the Entry Master Control should To Garage From Input be located in or near the garage. Door Opener 2 Device 2 To Garage Step 2 Mount Wall Bracket Door Opener 1 Common UP FULL FLASH CCI 1 CCI 2 COM 1 2 1 2 CCO 1 CCO 2 OUTPUTS INPUTS Attach wall bracket to wall using the supplied screws and wall anchors. Note: • Input devices can be timeclocks, motion sensors, telephone interfaces, etc. DANGER - • Do not connect line voltage power to the Entry Master Control. • Connecting line voltage power or improper wiring can result in personal injury or damage to the control or to other equipment. • All external control equipment must maintain Class 2 isolation. 8 RadioRA® Setup Guide for the Entry Master Control

Installing an Entry Master Control Step 4 Attach the AC Adapter Step 6 Plug in the AC Adapter Plug the AC Adapter into a 120VAC, 60Hz wall receptacle. Plug in power Section 2 - Installation cord. If the LEDs do not flash when powered, ? ensure that the AC adapter is installed properly and that there is power at the receptacle. If problem persists, call the Lutron Technical Support Center at (800) 523-9466. Step 5 Attach to Wall Bracket UP Align Entry Master Control and snap onto wall bracket. RadioRA® Setup Guide for the Entry Master Control 9

Activating an Entry Master Control Activating Control The Entry Master Control is a type of Master Control. The RadioRA® System can have a maximum of 12 Master Controls. Step 1 Begin Control activation REPEATER ACTIVATE VERIFY MAIN REPEATER BEEP Press and hold button for AUXILIARY CONTROLS FLASH 3 seconds. Section 3 - Start-Up Step 2 Activate Entry Master Control Press button. CCI 1 CCI 2 CCO 1 SECURITY FULL CCO 2 FLASH LEARN Step 3 Complete Control activation REPEATER ACTIVATE VERIFY MAIN REPEATER BEEP AUXILIARY CONTROLS FLASH Press and hold button for 3 seconds. For more detailed information, refer to the ? RadioRA® Setup Guide (P/N 044-001) 10 RadioRA® Setup Guide for the Entry Master Control

Button Programming Assigning a Column of Buttons as ROOMS or SCENES Step 1 Begin ROOM/SCENE assignment Press and hold buttons CCI 1 for 3 seconds. CCI 2 CCO 1 SECURITY FULL CCO 2 FLASH LEARN Section 3 - Start-Up Step 2 Change ROOM/SCENE Assignment SCENES Press corresponding button to assign ROOMS column as ROOM or SCENES. CCI 1 Only these CCI 2 buttons are CCO 1 SECURITY configurable. FULL CCO 2 FLASH LEARN Step 3 Complete ROOM/SCENE assignment Press and hold buttons CCI 1 for 3 seconds. CCI 2 CCO 1 SECURITY FULL CCO 2 FLASH LEARN For more detailed information, refer to the ? RadioRA® Setup Guide (P/N 044-001) RadioRA® Setup Guide for the Entry Master Control 11

Button Programming Assigning Dimmers, Switches, or GRAFIK Eye® Control Units to Buttons Step 1 Begin assigning Step 4 Select next button Press and hold buttons for 3 seconds. Press button. CCI 1 CCI 1 CCI 2 CCI 2 CCO 1 CCO 1 SECURITY SECURITY FULL FULL CCO 2 CCO 2 FLASH FLASH LEARN LEARN Section 3 - Start-Up Step 2 Select a button Step 5 Complete assigning Press and hold buttons Press button. for 3 seconds. CCI 1 CCI 1 CCI 2 CCI 2 CCO 1 CCO 1 SECURITY SECURITY FULL FULL CCO 2 CCO 2 FLASH FLASH LEARN LEARN For more detailed information, refer to the ? RadioRA® Setup Guide (P/N 044-001) Step 3 Assign a Dimmer, Switch or GRAFIK Eye® Control Unit Control to the button Press tapswitch. 12 RadioRA® Setup Guide for the Entry Master Control

Button Programming Setting Light Levels/GRAFIK Eye® Scene Selection for Buttons Step 1 Begin setting light levels Step 5 Select the next button Press and hold buttons Press button. for 3 seconds. CCI 1 CCI 1 CCI 2 CCI 2 CCO 1 CCO 1 SECURITY SECURITY FULL FULL CCO 2 CCO 2 FLASH FLASH LEARN LEARN Section 3 - Start-Up Step 2 Select a button Step 6 Complete setting light levels Press button. Press and hold buttons for 3 seconds. CCI 1 CCI 1 CCI 2 CCI 2 CCO 1 CCO 1 SECURITY SECURITY FULL FULL CCO 2 CCO 2 FLASH FLASH LEARN LEARN For more detailed information, refer to the ? RadioRA® Setup Guide (P/N 044-001) Step 3 Set light levels for Dimmers or GRAFIK Eye® scenes Press raise or lower to set level. RadioRA® Setup Guide for the Entry Master Control 13

Button Programming Configuring General Inputs as Maintained or Momentary Note: The Security Input is always a maintained CCI. Step 1 Begin CCI closure type Step 2 Changing the CCI closure type assignment assignments Simultaneously press and hold the FULL and Both General CCIs can be independently ALL ON buttons (approximately 3 seconds). selected as a Momentary or Maintained closure. Press and hold a CCI button to change it’s type. CCI 1 Shown: Setting CCI 2 CCI 2 as Maintained. CCO 1 CCI 1 SECURITY CCI 2 FULL CCO 1 CCO 2 FLASH SECURITY LEARN FULL CCO 2 FLASH Section 3 - Start-Up LEARN LED OFF = Momentary LED ON = Maintained CCI 1 CCI 2 CCO 1 CCI 1 SECURITY CCI 2 FULL CCO 1 CCO 2 SECURITY FLASH FULL LEARN CCO 2 FLASH LEARN FULL and FLASH LEDs will turn ON. Always Maintained 14 RadioRA® Setup Guide for the Entry Master Control

Button Programming Maintained Input Example Step 3 Complete CCI closure type assignment Simultaneously press and hold the FULL and ALL ON buttons (approximately 3 seconds). Switch Activate Release Open Switch Switch A Maintained switch closure will turn an input ROOM or SCENE ON. Input ROOM or SCENE remains ON until the switch closure is released. When released, the input ROOM or SCENE turns OFF. CCI 1 CCI 2 CCO 1 SECURITY FULL Momentary Input Example CCO 2 FLASH Section 3 - Start-Up LEARN Switch Activate Release Open Switch Switch A Momentary switch closure will turn an input ROOM or SCENE ON. A momentary switch closure cannot turn an input ROOM or SCENE OFF. CCI 1 CCI 2 CCO 1 SECURITY FULL CCO 2 FLASH LEARN All LEDs will turn OFF. RadioRA® Setup Guide for the Entry Master Control 15

Button Programming Entry Master Control Learning a Visor Control Step 1 Plan which Entry Master Step 3 Select an Entry Master Control Control buttons you want to Button learn Visor Control buttons Press and release Entry Master Control button that you want to learn a Visor Control button; its LED will turn ON. SUNSET HOME SUNRISE NIGHT CCO 1 1 GARAGE HOME AWAY GARAGE 1 SECURITY AWAY SUNSET HOME FULL WELCOME CCO 2 2 GARAGE SUNRISE NIGHT FLASH MORNING CCO 1 1 GARAGE SECURITY AWAY LEARN FULL WELCOME CCO 2 2 GARAGE ALL ON ALL OFF FLASH MORNING LEARN ALL ON ALL OFF Section 3 - Start-Up Step 2 Enter LEARN Mode Press and hold the LEARN button on the Entry Master Control until the green LEARN LED turns ON (approximately 3 seconds). SUNSET HOME SUNRISE NIGHT CCO 1 1 GARAGE SUNSET HOME SECURITY AWAY SUNRISE NIGHT FULL WELCOME CCO 1 1 GARAGE CCO 2 2 GARAGE SECURITY AWAY FLASH MORNING FULL WELCOME LEARN CCO 2 2 GARAGE FLASH MORNING ALL ON ALL OFF LEARN ALL ON ALL OFF LED turns ON. • If the ALL ON button is selected, LEDs in the right most column will cycle upward. • If the ALL OFF button is selected, LEDs in the right most column will cycle downward. • If either FULL or FLASH is selected, both the FULL and FLASH LEDs will turn ON. SUNSET HOME SUNRISE NIGHT CCO 1 1 GARAGE SECURITY AWAY FULL WELCOME CCO 2 2 GARAGE FLASH MORNING LEARN ALL ON ALL OFF The green LEARN LED turns ON. 16 RadioRA® Setup Guide for the Entry Master Control

Button Programming Step 4 Select Visor Control Button to Step 5 Repeat Steps 3 and 4 to learn be learned by the Entry Master additional Visor Control Control buttons Press and hold the Visor Control Button until the orange LED next to the selected Entry Master Control button flashes (approximately Step 6 Exit LEARN Mode 3 seconds). The LEARN LED will also flash while the Visor Control button is pressed. Press the LEARN button. HOME AWAY GARAGE 1 Section 3 - Start-Up SUNSET HOME SUNRISE NIGHT CCO 1 1 GARAGE SECURITY AWAY FULL WELCOME CCO 2 2 GARAGE FLASH MORNING LEARN ALL ON ALL OFF SUNSET HOME SUNRISE NIGHT CCO 1 1 GARAGE SECURITY AWAY FULL WELCOME CCO 2 2 GARAGE FLASH MORNING LEARN ALL ON ALL OFF SUNSET HOME SUNRISE NIGHT CCO 1 1 GARAGE SECURITY AWAY The orange LED will turn OFF after the Visor CCO 2 2 GARAGE FULL WELCOME Control button is released. The green LEARN FLASH MORNING LEARN LED will stay ON. ALL ON ALL OFF • To verify that the Entry Master Control The green LEARN LED turns OFF. button has learned the Visor Control buton, press the Visor Control button again. The orange LED on the Entry Master Control will flash. RadioRA® Setup Guide for the Entry Master Control 17

Advanced Programming Programming the ALL ON Button To program the ALL ON button, refer to the RadioRA® Setup Guide, Lutron P/N 044-001, section on “Programming the ALL ON Button.” Programming the ALL OFF Button To program the ALL OFF button, refer to the RadioRA® Setup Guide, Lutron P/N 044-001, section on “Programming the ALL OFF Button.” Copying Button Programming To copy button programming from another Master Control button, refer to the RadioRA® Setup Guide, Lutron P/N 044-001, section on “Copying Button Programming.” Erasing Button Programming To erase button programming from the Entry Master Control, refer to the RadioRA® Setup Guide, Lutron P/N 044- 001, section on “Erasing Button Programming.” Section 4 - Advanced Features 18 RadioRA® Setup Guide for the Entry Master Control

Advanced Programming Programming the FULL and FLASH Buttons The Security FULL and FLASH buttons are used for programming and diagnostic purposes only. Step 1 Begin FULL and FLASH Step 3 Assign Dimmers, Switches or button programming GRAFIK Eye® Control Units to Simultaneously press and hold the 2nd and the FULL button 4th buttons in the right most column until the • Dimmers and Switches assigned will turn on to full upper right LED begins to flash (approximately while in SECURITY Mode. 3 seconds). • GRAFIK Eye® Control Units assigned will go to scene 1 while in SECURITY Mode. Assign a Dimmer or Switch to the FULL button by turning the Dimmer or Switch ON. CCI 1 CCI 2 CCO 1 SECURITY Dimmer OR Switch FULL CCO 2 FLASH LEARN Section 4 - Advanced Features Upper right LED flashes. Assign a GRAFIK Eye® Control Unit to the Step 2 Select the FULL Button FULL button by pressing the scene 1 button. Press the FULL button. LUTRON CCI 1 CCI 2 CCO 1 SECURITY FULL CCO 2 FLASH LEARN If you assign the wrong Dimmer, Switch or GRAFIK Eye® Control Unit to the FULL button, turn the Dimmer, Switch or GRAFIK Eye® Control Unit OFF to unassign it. FULL LED will begin to flash. • Continued on next page. RadioRA® Setup Guide for the Entry Master Control 19

Advanced Programming Step 4 Select FLASH button Step 5 Assign Dimmers, Switches or GRAFIK Eye® Control Units to Press the FLASH button. the FLASH button • Dimmers and Switches assigned will flash ON and OFF while in SECURITY Mode. • GRAFIK Eye® Control Units assigned will alternate between scene 1 and OFF while in SECURITY CCI 1 CCI 2 CCO 1 SECURITY Mode. FULL CCO 2 FLASH Assign a Dimmer or Switch to the FLASH LEARN button by turning the Dimmer or Switch ON. Dimmer OR Switch Section 4 - Advanced Features CCI 1 CCI 2 CCO 1 SECURITY FULL CCO 2 FLASH LEARN Assign a GRAFIK Eye® Control Unit to the FLASH button by pressing the scene 1 button. FLASH LED will begin to flash. LUTRON If you assign the wrong Dimmer, Switch or GRAFIK Eye® Control Unit to the FLASH button, turn the Dimmer, Switch or GRAFIK Eye® Control Unit OFF to unassign it. 20 RadioRA® Setup Guide for the Entry Master Control

Advanced Programming Step 6 Complete FULL and FLASH button programming CCI 1 CCI 2 CCO 1 SECURITY FULL CCO 2 FLASH LEARN Simultaneously press and hold the 2nd and 4th buttons in the right most column until all the LEDs begin to flutter (approximately 3 seconds). Section 4 - Advanced Features CCI 1 CCI 2 CCO 1 SECURITY FULL CCO 2 FLASH LEARN RadioRA® Setup Guide for the Entry Master Control 21

Advanced Programming Deleting ALL Visor Control Transmitters from an Entry Master Control Deleting all Visor Controls from an Entry Master Control will permanently delete all Visor Control Transmitter Buttons previously learned. Step 1 Begin deleting ALL Visor Step 2 Delete ALL Visor Controls Controls Press and hold the CCI 1, FULL, and ALL ON buttons in the middle column until the CCI 1 Press and hold the LEARN button until its LED and FULL LEDs begin to flash (approximately turns ON (approximately 3 seconds). 3 seconds). CCI 1 CCI 1 CCI 2 CCI 2 CCO 1 CCO 1 SECURITY SECURITY FULL FULL CCO 2 CCO 2 FLASH FLASH LEARN LEARN Section 4 - Advanced Features CCI 1 CCI 2 CCO 1 SECURITY FULL CCO 2 FLASH LEARN CCI 1 CCI 2 CCO 1 SECURITY FULL The CCI 1 and FULL LEDs flash. CCO 2 FLASH LEARN The green LEARN LED turns ON. 22 RadioRA® Setup Guide for the Entry Master Control

Advanced Programming While the CCI 1 and FULL LEDs are Step 3 Complete deleting ALL Visor flashing, press and hold the CCI 2 and Controls FLASH buttons in the middle column until all the LEDs flash. Press the LEARN button. CCI 1 CCI 2 CCO 1 CCI 1 SECURITY CCI 2 FULL CCO 1 CCO 2 SECURITY FLASH FULL LEARN CCO 2 FLASH LEARN Section 4 - Advanced Features CCI 1 CCI 2 CCO 1 SECURITY FULL CCO 2 FLASH LEARN All LEDs (except the LEARN) flutter. CCI 1 CCI 2 CCO 1 SECURITY FULL CCO 2 FLASH LEARN The green LEARN LED turns OFF. CCI 1 CCI 2 CCO 1 SECURITY FULL CCO 2 FLASH LEARN All LEDs will turn OFF (except the LEARN), indicating that ALL Visor Controls have been deleted from the Entry Master Control. RadioRA® Setup Guide for the Entry Master Control 23

Troubleshooting Guide Proper operation of the RadioRA® Wireless Central Home Lighting Control System is based upon a complex series of radio frequency (RF) communications between system components. As such, it is highly dependent upon proper system installation and programming of controls. If you experience difficulties programming or operating your RadioRA® system, please refer to this guide. Many symptoms of common system activation or programming errors are contained in this Troubleshooting Guide. If you are having a problem with your system not described here, or if you have any questions, call the Lutron Technical Support Center at 1-800-523-9466. Symptom Possible Cause Remedy I ACTIVATE CONTROLS LED on Your system has encountered a Discontinue activating your RadioRA® MAIN or AUXILIARY Repeater neighboring system within RF system until activation of the neighboring turns ON and then back OFF communication range also in system is complete. when attempting to go into ACTIVATE CONTROLS mode. ACTIVATE CONTROLS mode. II After activating a Multi-Function Multi-Function Entry Master Move a system Repeater closer to the Entry Master Control, the Multi- Control is out of RF communica- Multi-Function Entry Master Control in Function Entry Master Control tion range of nearest system question, or you may have to add another LEDs flutter for approximately 5 Repeater. Repeater. seconds then go out. System not in ACTIVATE Place system in ACTIVATE CONTROLS CONTROLS mode. mode. III The Multi-Function Entry Master No power available to the Multi- Check that breaker is on and not tripped. Control appears not to be Function Entry Master Control. working at all and the LEDs are OFF. Faulty power supply. Verify that the plug in power supply is working. IV The Multi-Function Entry Master The Multi-Function Entry Master Reprogram the Multi-Function Entry Control appears not to be Control was not programmed Master Control. working at all and the LEDs are properly. glowing dimly. The Multi-Function Entry Master Verify whether the Multi-Function Entry Section 5 - Troubleshooting Control may be out of RF Master Control is in range of a Repeater communication range of the by placing the system in BEEP mode. nearest Repeater. (Refer to the Troubleshooting Section in the RadioRA® Setup Guide P/N 044-001.) V The Visor Control Transmitter is Entry Master Control failed to Entry Master Control must learn Visor not communicating with the learn Visor Control Transmitter. Control Transmitter. Multi-Function Entry Master Control. Batteries weak or dead. Replace batteries in Visor Control Transmitter with new ones (CR2032). 24 RadioRA® Setup Guide for the Entry Master Control

Returning to Default Factory Settings Entry Master Control Returning an Entry Master Control to Default Factory Settings will permanently delete all current programming information. Do not do this unless you are sure that it is necessary. For more information call the Lutron Technical Support Center at 1-800-523-9466. Step 1 Begin returning to Default Step 2 Complete returning to Default Factory Settings Factory Settings Ensure that the ACTIVATE REPEATER LED While the 1st, 3rd, and 5th LED are and ACTIVATE CONTROLS LED on any flashing, press and hold the 2nd and 4th Repeater is NOT ON before proceeding. If buttons in the right most column until all the either LED is ON, press the corresponding LEDs (except the LEARN) flash button until its LED turns OFF (approximately 3 (approximately 3 seconds). seconds). Press and hold the 1st, 3rd and 5th buttons in the right most column until the corresponding LEDs begin to flash (approximately 3 CCI 1 CCI 2 seconds). CCO 1 SECURITY FULL CCO 2 FLASH LEARN CCI 1 CCI 2 CCO 1 SECURITY FULL CCO 2 FLASH LEARN CCI 1 Section 5 - Troubleshooting CCI 2 CCO 1 SECURITY FULL CCO 2 FLASH LEARN All LEDs (except the LEARN) flash. CCI 1 CCI 2 CCO 1 SECURITY FULL CCO 2 FLASH LEARN CCI 1 CCI 2 CCO 1 SECURITY FULL CCO 2 FLASH LEDs will flash for only 3 seconds. LEARN All LEDs will turn OFF, indicating that the Master Control has been returned to Default Factory Settings. RadioRA® Setup Guide for the Entry Master Control 25

Notes Section 5 - Troubleshooting 26 RadioRA® Setup Guide for the Entry Master Control

Notes Section 5 - Troubleshooting RadioRA® Setup Guide for the Entry Master Control 27

Limited Warranty World Headquarters Lutron will, at its option, repair or replace any unit that Lutron Electronics Co., Inc. is defective in materials or manufacture within one 7200 Suter Road year after purchase. For warranty service, return unit Coopersburg, PA 18036-1299 U.S.A. to place of purchase or mail to Lutron Electronics Co., TOLL FREE: (800) 523-9466 (U.S.A., Canada, and Inc. at 7200 Suter Rd., Coopersburg, PA 18036-1299, the Caribbean) postage pre-paid. Tel: (610) 282-3800 THIS WARRANTY IS IN LIEU OF ALL OTHER Fax: (610) 282-3090 EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO ONE YEAR FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL DAMAGES. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty may last, so the above limitations may not apply to you. This product may be covered under one or more of the following U.S. patents: 4,835,343; 4,954,768; 5,248,919; 5,399,940; 5,637,930; 5,736,965; 5,798,581; 5,838,226; 5,848,054; 5,905,442; 5,982,103; DES 353,798; DES 378,814; DES 389,461; DES 389,805; DES 395,037; DES 404,013; DES 422,969; DES 428,855; DES 436,579; DES 439,220 and corresponding foreign patents. U.S. and foreign patents pending. Lutron, RadioRA, and GRAFIK Eye are registered trademarks, and FASS is a trademark of Lutron Electronics Co., Inc. © 2001 Lutron Electronics Co., Inc. Technical Assistance If you have questions concerning the installation or operation of this product, call the Lutron Technical Lutron Electronics Co., Inc., reserves the right to make Support Center. Please provide exact model number improvements or changes in its products without prior when calling. notice. Although every attempt is made to ensure that (800) 523-9466 (U.S.A., Canada, and the Caribbean) this information is accurate and up to date, please Other countries call (610) 282-3800 check with Lutron to confirm product availability, latest Fax (610) 282-3090 specifications and suitability for your application. Visit our web site at www.lutron.com © 2001 Lutron Electronics Co., Inc. MADE ANDRadioRA 28 PRINTED IN® Setup U.S.A. Guide for the Entry Master Control P/N 044-022 11/01 Rev. A


Document Created: 2006-11-10 09:54:33
Document Modified: 2006-11-10 09:54:33
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC