Users Manual

FCC ID: JPZ0034

Users Manual

Download: PDF
FCCID_481501

Hybrid Repeater Installation Instructions HR-REP-120 Please Read Before Installing 120 V 60 Hz (9 V 300 mA adapter) Overview HomeWorks Hybrid Repeaters add RF capability to HomeWorks processors configured with a Hybrid Repeater Link and provide an additional coverage area for radio frequency (RF) signals sent between HomeWorks RF Dimmers/Switches, RF Keypads, and RF Processors. Each repeater covers a sphere of English approximately 2500 square feet (232m2) of living space. Up to five (5) repeating devices may be placed in a HomeWorks RF system (a HomeWorks RF Processor counts as one of the repeating devices). Español HR-REP-120 Français Important Notes Codes: Install in accordance with all local and nation- al electrical codes. Português Power: The Hybrid Repeater can be powered from EITHER of two sources: 1. Adapter power. Use only the adapter pro- vided with the Hybrid Repeater (Lutron model # T120-9DC-3-WH). Caution - Using an adapter not rated at the following specifications could damage the Hybrid Repeater Wiring: Hybrid Repeater wiring repeater and possibly overheat the adapter. must be in a daisy chain configuration. The total • Input: 120 V 60 Hz length of wire on the Hybrid Repeater Link may be up • Output: 9 V 300 mA to 1000 feet (305 m), and may contain up to five (5) NEC Class 2; IEC PELV Hybrid Repeaters. 2. Link power. Use only power supplied via a Cleaning: To clean, wipe with a clean damp cloth. DO HomeWorks Processor Hybrid Repeater NOT use any chemical cleaning solutions. Link or a HomeWorks auxiliary power sup- ply. (See section about the HWI-PS in the Device Placement: HomeWorks Hybrid Repeaters HomeWorks Technical Reference Guide or must be located within 30 feet (9 m) of the RF Application Note HW-104.) Each hybrid Dimmers, Switches, and Keypads they are covering. repeater counts as 30 LEDs. Hybrid Repeaters must also be within 60 feet (18 m) Note: An RF Processor does not supply of an RF Processor or another repeater when using power on the Hybrid Repeater Link. the RF Link for repeater-to-repeater or repeater-to- Environment: Ambient operating temperature: processor communication. When using the Wired Link 32-104°F (0-40°C), 0-90% humidity, non-condensing. for repeater-to-repeater or repeater-to-processor com- Indoor use only. munication, a total wire length of 1000 feet (305 m) may be used. FCC Information NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, persuant to part 15 of the FCC rules. 1 Operation is subject to the following: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Installation Wall Mounting Hybrid Repeaters may be wall mounted using the 1. Find a suitable location for the Hybrid Repeater. supplied wall bracket. Place the repeater in a convenient and accessible location. Note: Hybrid Repeaters must be within 60 feet (18 m) of an RF Processor or another repeater 1. Attach wall bracket to wall using the supplied when using the RF Link for repeater-to-repeater or screws and wall anchors. repeater-to-processor communication. 2. Connect Hybrid Repeater Link (if applicable). UP Connect the Hybrid Repeater Link communication wires from the HomeWorks® Processor (or previous English Hybrid Repeater in the daisy chain) to the terminal block on the Hybrid Repeater (see Wiring Diagram). Each terminal will accept up to three 22-18 AWG (0.5-1.0 mm2) wires. 2. Place power cord into notches at top and bottom of Note: If using the plug-in adapter to power the wall bracket. Wrap excess power cord around the repeater, DO NOT connect the +15 V terminal cord holder. Route Hybrid Repeater Link wiring Español (terminal 2). through hole in wall bracket and out through side cutout. Align repeater and snap onto wall bracket. 3. Apply power to the Hybrid Repeater. If the Hybrid Repeater is to be powered by the Hybrid Hybrid Repeater Link Power Cord Repeater Link, apply power by turning on the Wiring HomeWorks Processor. If the Hybrid Repeater is to be powered by the plug-in adapter, insert the Français adapter cord plug into the jack on the Hybrid Repeater, then plug the adpater into a standard UP wall receptacle. STATUS and TEST LEDs will be dimly lit when Português first powered Plug in power cord and adapter Operation RF TX/RX LEDs WIRED TX/RX LEDs Indicate RF Link Indicate Wired Link activity. activity. Plug in adapter jack Wiring Diagram HR-REP-120 (Side View) STATUS Button Used when addressing the Hybrid Repeater from the HomeWorks IlluminationTM Software. MUX MUX TEST LED TEST Button +15 V A slow flash indicates Activates RF communication COM RF communications tests. To activate the tests, tests are in progress press and hold the TEST Button until the TEST LED STATUS LED begins to flash. Indicates the status of the HomeWorks Note: For communication tests, system. the Hybrid Repeater, Note: When the Hybrid Repeater is HomeWorks Processor, and powered, but has not yet been assigned other RF devices must first be an address from the HomeWorks configured and addressed Illumination Software, the STATUS and using the HomeWorks TEST LEDs will be dimly illuminated. Illumination Software. 2

System Communications RF Communications RF Tabletop Keypad 30 ft. (9 m) maximum Hybrid Repeater English RF Dimmer RF Keypad Español RF Processor * Sta * 1 2 3 4 60 ft. (18 m) maximum between RF Processors and Repeaters, or between 30 ft. (9 m) maximum Français Repeaters RF Communications Notes • Hybrid Repeaters must be located within 30 feet (9 m) of the RF Dimmers/Switches and Keypads they are covering. Português • Hybrid Repeaters must also be within 60 feet (18 m) of an RF Processor or another repeater. • Multiple repeaters may be necessary to provide adequate coverage. Up to four (4) repeaters may be used with each RF Processor, and up to five (5) Hybrid Repeaters may be used with each 8 SeriesTM Processor or 4 SeriesTM Processor (equipped with Hybrid Repeater Link). Hybrid Repeater Link (Wired) Communications HomeWorks® Processor RF Keypad Hybrid Repeater (8 Series shown) 30 ft. (9 m) maximum Hybrid Repeater Link Hybrid Repeater Link 1000 ft. (305 m) maximum 60 ft. (18 m) 1000 ft. (305 m) maximum wire run distance wire run distance maximum 3

Troubleshooting Guide Symptom Cause and Action No LEDs are illuminated on the Hybrid Repeater. No power available to unit. • If powered by the 9 V plug-in adapter, verify there is power to the adapter. • If powered by the Hybrid Repeater Link, verify link wiring. Button presses on the Hybrid Repeater cause the Repeater has not been addressed. STATUS LED on the repeater to flash rapidly. • Address the repeater using the HomeWorks® English IlluminationTM Software. Español Français Português FCC Information Note: This equipment has been tested and found to comply with the limits for a Class B digi- tal device, pursuant to Part 15 of the FCC rules. These limits are designed to provide rea- sonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip- ment does cause harmful interference to radio or television reception, which can be deter- mined by turning the equipment off and on, the user is encouraged to try to correct the inter- ference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the seperation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. LIMITED WARRANTY Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could Lutron will, at its option, repair or replace any unit that is defective in materials or manufac- void the user’s authority to operate this equipment. ture within two years after purchase. After the two year period, a pro-rated warranty applies to this product until eight years after the purchase. For warranty service, return unit to place NOTE: This equipment has been tested and found to comply with the limits for a Class B of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre- digital device, persuant to part 15 of the FCC rules. paid. Telephone the Lutron Technical Support Center toll free at 800-523-9466. For more Operation is subject to the following: information regarding this warranty contact your Lutron representative. (1) This device may not cause harmful interference, and THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE (2) this device must accept any interference received, including interference that may cause IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO TWO YEARS FROM PUR- undesired operation. CHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, Technical and Sales Assistance OR IMPROPER OR INCORRECT REPAIR, OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUEN- If you need assistance, call the toll-free Lutron TIAL DAMAGES. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT Technical Support Center. Please provide exact OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT. model number when calling. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow limitations on how long an implied warranty lasts, (800) 523-9466 (U.S.A., Canada and the Caribbean) so the above limitation may not apply to you. Some states do not allow the exclusion or limi- Other countries call: tation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.This product may be covered by one or more of the following U.S. patents: Tel: (610) 282-3800 4,835,343; 5,736,965; 5,838,226; 5,848,054; 5,905,442; 5,982,103; D389,805; D404,013 and Fax: (610) 282-3090 corresponding foreign patents. U.S. and foreign patents pending. Lutron and HomeWorks are registered trademarks and Illumination is a trademark of Lutron Electronics Co., Inc. Visit our Web site at www.lutron.com © 2004 Lutron Electronics Co., Inc. Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299 Made and printed in the U.S.A. 1/04 P/N 043-xxx Rev. A (PENDING)


Document Created: 2004-09-23 09:18:40
Document Modified: 2004-09-23 09:18:40
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC