Test Report

FCC ID: JOYYKCA04

Test Report

Download: PDF
FCCID_2968318

Page 1 of 28 TEST REPORT Report number : 2Z101C—16040 Issue date : April 5, 2016 The device, as described herewith, was tested pursuant to applicable test procedure and complies with the requirements of,; FCC Part 24 Subpart E The test results are traceable to the international or national standards. Applicant : KYOCERA Corporation Equipment under test (EUT) : Mobile Phone Model number : YKCAO4 FCC ID : JOYYKCAO4 Date of test : February 26, March 3, 7, 9, 17, 18, 22, 25, 2016 Test place : TUV SUD Zacta Ltd. Yonezawa Testing Center 4149—7 Hachimanpara 5—chome Yonezawa—shi Yamagata 992—1128 Japan Phone: +81—238—28—2880 Fax: +81—238—28—2888 Test results : Complied The results in this report are applicable only to the equipment tested. . This report shall not be re—produced except in full withoutthe written approval of TUV SUD Zacta Ltd. This test report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. Tested by j KAZMI’U",‘ Salto ///&L% %L m _ Kazunori Saito Chiaki Kanno EAlikon %k{fix/’y Hikaru Shibata Authorized by : dare 7 Rooteda) 4 7 Hiroaki Suzuki Manager of EMC Technical Department nvilad NVLAP LAB CODE 200306—0 TUV SUD Zacta Ltd. Report number: Z101C—16040 Test Report Rev.FCC—24E2.1 FCC ID: JOYYKCA4

Page 2 of 28 Table of contents Page 1. Summary of Test .................................................................................................................4 1.1 Purpose of test ....................................................................................................................................... 4 1.2 Standards ............................................................................................................................................... 4 1.3 List of applied test to the EUT .............................................................................................................. 4 1.4 Modification to the EUT by laboratory................................................................................................. 4 2. Equipment Under Test ........................................................................................................5 2.1 General Description of equipment ....................................................................................................... 5 2.2 EUT information ..................................................................................................................................... 5 2.3 Variation of the family model(s)............................................................................................................ 6 2.4 Description of Test mode ...................................................................................................................... 6 3. Configuration of equipment ...............................................................................................7 3.1 Equipment(s) used................................................................................................................................. 7 3.2 System configuration ............................................................................................................................ 7 4. Conducted Output Power ...................................................................................................8 4.1 Measurement procedure ....................................................................................................................... 8 4.2 Measurement result ............................................................................................................................... 8 5. Equivalent Isotropic Radiated Power ................................................................................9 5.1 Measurement procedure ....................................................................................................................... 9 5.2 Calculation method.............................................................................................................................. 10 5.3 Limit....................................................................................................................................................... 10 5.4 Test data.................................................................................................................................................11 6. Peak to Average Ratio.......................................................................................................12 6.1 Measurement procedure ..................................................................................................................... 12 6.2 Limit....................................................................................................................................................... 12 6.3 Measurement result ............................................................................................................................. 12 6.4 Trace data ............................................................................................................................................. 13 7. Occupied Bandwidth.........................................................................................................14 7.1 Measurement procedure ..................................................................................................................... 14 7.2 Limit....................................................................................................................................................... 14 7.3 Measurement result ............................................................................................................................. 14 7.4 Trace data ............................................................................................................................................. 15 8. Band Edge Spurious and Harmonic at Antenna Terminals ...........................................16 8.1 Measurement procedure ..................................................................................................................... 16 8.2 Limit....................................................................................................................................................... 16 8.3 Measurement result ............................................................................................................................. 16 8.4 Trace data ............................................................................................................................................. 17 9. Radiated Emissions and Harmonic Emissions...............................................................21 9.1 Measurement procedure ..................................................................................................................... 21 9.2 Calculation method.............................................................................................................................. 22 9.3 Limit....................................................................................................................................................... 22 9.4 Test data................................................................................................................................................ 23 10. Frequency Stability .........................................................................................................24 10.1 Measurement procedure ................................................................................................................... 24 TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 3 of 28 10.2 Limit..................................................................................................................................................... 24 10.3 Measurement result ........................................................................................................................... 25 11. Uncertainty of measurement ..........................................................................................26 12. Laboratory description ...................................................................................................27 Appendix A. Test equipment ................................................................................................28 TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 4 of 28 1. Summary of Test 1.1 Purpose of test It is the original test in order to verify conformance to FCC Part 24 Subpart E. 1.2 Standards CFR47 FCC Part 24 Subpart E 1.2.1 Test Methods KDB 971168 D01 Power Meas License Digital Systems v02r02 ANSI/TIA/EIA-603-D-2010 1.2.2 Deviation from standards None 1.3 List of applied test to the EUT Test items Test items Condition Result Section 2.1046 Conducted Output Power Conducted PASS Effective Radiated Power 24.232(c) Radiated PASS Equivalent Isotropic Radiated Power 24.232(d) Peak to Average Ratio Conducted PASS 24.238(a) Occupied Bandwidth Conducted PASS 2.1049 24.238(a) Band Edge Spurious and Harmonic at Conducted PASS 2.1051 Antenna Terminal 24.238(a) Radiated emissions and Radiated PASS 2.1053 Harmonic Emissions 24.235 Frequency Stability Conducted PASS 2.1055 1.3.1 Test set up Table-Top 1.4 Modification to the EUT by laboratory None TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 5 of 28 2. Equipment Under Test 2.1 General Description of equipment EUT is the Mobile Phone. 2.2 EUT information Applicant : KYOCERA Corporation Yokohama Office 2-1-1 Kagahara, Tsuzuki-ku Yokohama-shi, Kanagawa, Japan Phone: +81-45-943-6253 Fax: +81-45-943-6314 Equipment under test : Mobile Phone Trade name : Kyocera Model number : YKCA04 Serial number : N/A EUT condition : Pre-Production Power ratings : Battery: DC 3.8V Size : (W) 71.6× (D) 10.7 × (H) 142 mm Environment : Indoor and Outdoor use Thermal limitation : -20˚C to 60˚C RF Specification Frequency of : Up Link Operation GSM1900: 1850.2-1909.8MHz Down Link GSM1900: 1930.2-1989.8MHz Modulation type : GSM1900: GMSK Emission designator : GSM1900: 247KGXW Output power : GSM1900: 0.889W (29.54dBm) Antenna type : Internal antenna Antenna gain : GSM1900: -0.4dBi TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 6 of 28 2.3 Variation of the family model(s) Not applicable 2.4 Description of Test mode The EUT had been tested under operating condition. There are three channels have been tested as following: Band Channel Frequency 512 1850.2MHz GSM1900 661 1880.0MHz 810 1909.8MHz The field strength of spurious emissions was measured at each position of all three axis X, Y and Z to compare the level, and the maximum noise. The worst emission was found in X axis and the worst case recorded. TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 7 of 28 3. Configuration of equipment 3.1 Equipment(s) used No. Equipment Company Model No. Serial No. FCC ID / DoC Comment 1 Mobile Phone KYOCERA YKCA04 N/A JOYYKCA04 EUT 3.2 System configuration 1. Mobile Phone (EUT) Note1: Numbers assigned to equipment or cables on this diagram correspond to the list in “3.1 Equipment(s) used”. TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 8 of 28 4. Conducted Output Power 4.1 Measurement procedure [FCC 2.1046] The conducted output power was measured with a wireless communication tester connected to the antenna terminal. The wireless communication tester parameters were set to produce the maximum power from the EUT. - Test configuration Wireless EUT Communication Coaxial cable Tester 4.2 Measurement result Date : February 26, 2016 Temperature : 24.3 [˚C] Humidity : 33.3 [%] Test engineer : Test place : Shielded room No.4 Chiaki Kanno Maximum Burst-Averaged Output Power [dBm] GPRS/EDGE(GMSK)Data Frequency Voice Band Channel GPRS GPRS GPRS GPRS [MHz] GSM 1 TX 2 TX 3 TX 4 TX CS 1slot Slot Slot Slot Slot 512 1850.2 29.44 29.41 28.39 26.46 24.95 PCS 661 1880.0 29.54 29.51 28.47 26.53 25.16 1900 810 1909.8 29.54 29.54 28.57 26.58 25.13 TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 9 of 28 5. Equivalent Isotropic Radiated Power 5.1 Measurement procedure [FCC 24.232(c)] <Step 1> The EUT and support equipment are placed on a 1 meter x 1 meter surface, 0.8 meter height Styrofoam table. Radiated emission measurements are performed at 3 meter distance with the broadband antenna (double ridged guide antenna). The antenna is positioned both the horizontal and vertical planes of polarization and height is varied 1 to 4 meters and stopped at height producing the maximum emission. The bandwidth of the spectrum analyzer is set to 1MHz. The turntable is rotated by 360 degrees and stopped at azimuth of producing the maximum emission. <Step 2> The substitution antenna is replaced by the transmitter antenna (EUT). The frequency of the signal generator is adjusted to the measurement frequency. Level of the signal generator is adjusted to the level that is obtained from step 1, and record the emission level of signal generator. The spectrum analyzer is set to; a) Span = 1.5 times the OBW b) RBW = 1-5% of the expected OBW, not to exceed 1MHz c) VBW ≥ 3 x RBW d) Number of sweep points ≥ 2 x span / RBW e) Sweep time = auto-couple f) Detector = RMS (power averaging) g) If the EUT can be configured to transmit continuously (i.e., burst duty cycle ≥ 98%), then set the trigger to free run. h) If the EUT cannot be configured to transmit continuously (i.e., burst duty cycle < 98 %), then use a sweep trigger with the level set to enable triggering only on full power bursts and configure the EUT to transmit at full power for the entire duration of each sweep. Ensure that the sweep time is less than or equal to the transmission burst duration. i) Trace average at least 100 traces in power averaging (i.e., RMS) mode. j) Compute the power by integrating the spectrum across the OBW of the signal using the instrument’s band power measurement function, with the band limits set equal to the OBW band edges. If the instrument does not have a band power function, then sum the spectrum levels (in linear power units) at intervals equal to the RBW extending across the entire OBW of the spectrum. - Test configuration TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 10 of 28 5.2 Calculation method Result (EIRP) = S.G Reading – Cable loss + Antenna Gain Margin = Limit – Result (EIRP) Example: Limit @ 1880MHz : 33.0dBm S.G Reading = 18.9dBm Cable loss = 1.1dB Ant. Gain = 8.3dBi Result = 18.9 - 1.1 + 8.3 = 26.1dBm Margin = 33.0 - 26.1 = 6.9dB 5.3 Limit 2 W (33dBm) TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 11 of 28 5.4 Test data Date : March 9, 2016 Temperature : 23.9 [˚C] Humidity : 29.8 [%] Test engineer : Test place : 3m Semi-anechoic chamber Kazunori Saito Date : March 22, 2016 Temperature : 22.1 [˚C] Humidity : 22.6 [%] Test engineer : Test place : 3m Semi-anechoic chamber Kazunori Saito [GSM1900] Frequency S.A Reading S.G Reading Cable loss Ant.Gain Result Limit Margin H/V [MHz] [dBm] [dBm] [dB] [dBi] [dBm] [dBm] [dB] V 1850.2 -25.7 22.6 1.1 8.3 29.9 33.0 3.1 V 1880.0 -25.7 23.1 1.1 8.3 30.3 33.0 2.7 V 1909.8 -26.2 23.9 1.1 8.3 31.1 33.0 1.9 TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 12 of 28 6. Peak to Average Ratio 6.1 Measurement procedure [FCC 24.232(d)] The peak to average ratio was measured with a spectrum analyzer connected to the antenna terminal. The spectrum analyzer is set to; a) Span= 5MHz b) RBW = 1MHz c) VBW 2 3 x RBW d) Detector = Peak / Average e) Sweep time = auto—couple £) Trace mode=Max hold — Test configuration Power splitter Spectrum Wireless Analyzer Attenuator Communication Coaxial cable Coaxial cable Tester EUT 6.2 Limit 13dB orless 6.3 Measurement result Date March 18, 2016 Temperature 211 [C] Humidity 35.4 [%] Test engineer Test place Shielded room No.4 Hikaru Shibata Mod ch f Frequency Peak to Average Power Ratio Limit oae anne [MHz] [dB] [dB] 512 1850.2 0.01 GSM1900 661 1880.0 0.02 13.0 810 1909.8 0.01 TUV SUD Zacta Ltd Report number: 2101C—16040 Test Report RevFCC—24E2.1 FCC ID: JOYYKCAQ4

Page 13 of 28 6.4 Trace data [GSM1900] Channel: 512 Channel: 661 Channel: 810 TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 14 of 28 7. Occupied Bandwidth 7.1 Measurement procedure [FCC 24.238(a), 2.1049] The Occupied bandwidth was measured with a spectrum analyzer connected to the antenna terminal. The spectrum analyzer is set to; a) RBW = 1-5% of the expected OBW & VBW ≥ 3 x RBW b) Detector = Peak c) Trace mode = Max hold d) Sweep time = auto-couple - Test configuration Power splitter Spectrum Wireless Analyzer Attenuator Communication Coaxial cable Coaxial cable Tester EUT 7.2 Limit None 7.3 Measurement result Date : March 7, 2016 Temperature : 22.8 [˚C] Humidity : 36.6 [%] Test engineer : Test place : Shielded room No.4 Hikaru Shibata Frequency Test Result Band Channel (MHz) (kHz) 512 1850.2 242.5585 GSM1900 661 1880.0 244.0574 810 1909.8 246.8853 TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 15 of 28 7.4 Trace data [GSM1900] Channel: 512 Channel: 661 Channel: 810 TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 16 of 28 8. Band Edge Spurious and Harmonic at Antenna Terminals 8.1 Measurement procedure [FCC 24.238(a), 2.1051] The band edge spurious and harmonic was measured with a spectrum analyzer connected to the antenna terminal. The spectrum analyzer is set to; <Band Edge> a) Span was set large enough so as to capture all out of band emissions near the band edge b) RBW ≥ 1% of the emission bandwidth or 2% of the emission bandwidth c) VBW ≥ 3 x RBW d) Detector = RMS e) Trace mode = Max hold f) Sweep time = auto-couple g) Number of sweep point ≥ 2 x span / RBW <Spurious Emissions> a) RBW = 1MHz & VBW ≥ 3 x RBW b) Detector = Peak c) Trace mode = Max hold d) Sweep time = auto-couple e) Number of sweep point ≥ 2 x span / RBW - Test configuration Power splitter Spectrum Wireless Analyzer Attenuator Communication Coaxial cable Coaxial cable Tester EUT 8.2 Limit -13dBm or less 8.3 Measurement result Date : March 18, 2016 Temperature : 21.1 [˚C] Humidity : 35.4 [%] Test engineer : Test place : Shielded room No.4 Hikaru Shibata Frequency Limit Band Channel Results Results [MHz] [dB] 512 1850.2 -13.0 See the trace data PASS GSM1900 810 1909.8 -13.0 See the trace data PASS TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 17 of 28 8.4 Trace data [GSM1900] (Band Edge) Channel: 512 Channel: 810 TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 18 of 28 (Spurious Emissions) Note: Conducted spurious test was measured in the worst case of conducted output power. Channel: 512 30MHz-5GHz 5GHz-10GHz 10GHz-15GHz 15GHz-20GHz TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 19 of 28 Channel: 661 30MHz-5GHz 5GHz-10GHz 10GHz-15GHz 15GHz-20GHz TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 20 of 28 Channel: 810 30MHz-5GHz 5GHz-10GHz 10GHz-15GHz 15GHz-20GHz TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 21 of 28 9. Radiated Emissions and Harmonic Emissions 9.1 Measurement procedure [FCC 24.238(a), 2.1053] <Step 1> The EUT and support equipment are placed on a 1 meter x 1 meter surface, 0.8 meter height Styrofoam table. Radiated emission measurements are performed at 3 meter distance with the broadband antenna (Biconical antenna, Log periodic antenna and double ridged guide antenna). The antenna is positioned both the horizontal and vertical planes of polarization and height is varied 1 to 4 meters and stopped at height producing the maximum emission. The bandwidth of the spectrum analyzer is set to 1MHz. The turntable is rotated by 360 degrees and stopped at azimuth of producing the maximum emission. The frequency is investigated up to 20GHz. <Step 2> The substitution antenna is replaced by the transmitter antenna (EUT). The frequency of the signal generator is adjusted to the measurement frequency. Level of the signal generator is adjusted to the level that is obtained from step 1, and record the emission level of signal generator. The spectrum analyzer is set to; a) RBW = 100kHz for below 1GHz and 1MHz for above 1GHz / VBW ≥ 3 x RBW b) Detector = Peak c) Trace mode = Max hold d) Sweep time = auto-couple - Test configuration TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 22 of 28 9.2 Calculation method Result = S.G Reading – Cable loss + Antenna Gain Margin = Limit – Result (EIRP) Example: Limit @ 3757.5MHz : -13.0dBm S.G Reading = -54.3dBm Cable loss = 1.6dB Ant. Gain = 9.2dBi Result = -54.3 - 1.6 + 9.2 = -46.7dBm Margin = -13.0 - (-46.7) = 33.7dB 9.3 Limit -13dBm or less TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 23 of 28 9.4 Test data Date March 3, 2016 Temperature 224 [C] Humidity 23.8 [%] Test engineer Test place 3m Semi—anechoic chamber Kazunori Saito Date March 17, 2016 Temperature 231 [C] Humidity 224 [%] Test engineer Test place 3m Semi—anechoic chamber Kazunori Saito Date March 22, 2016 Temperature 221 [C] Humidity 22.6 [%] Test engineer Test place 3m Semi—anechoic chamber Kazunori Saito [GSM1900] (Channel: 512) Ey Frequency S.A Reading $.G Reading Cable loss AntGain Result Limit Margin [MHz] [dBm] [dBm] [dB] [dBi] [dBm] [dBm] [dB] H 37004 535 —53.1 1.6 92 455 130 325 37004 54.9 —55.8 1.6 92 482 130 35.2 (Channel: 661) Ey Frequency S.A Reading $.G Reading Cable loss AntGain Result Limit Margin [MHz] [dBm] [dBm] [dB] [dBi] [dBm] [dBm] [dB] H 3760.0 53.3 53.3 1.6 93 456 130 326 V 3760.0 55.3 —57.0 1.6 93 49.3 130 363 H 5640.0 —55.8 53.3 20 114 139 130 309 V 5640.0 —56.0 —57.0 20 92 498 130 36.8 (Channel: 810) Ey Frequency S.A Reading $.G Reading Cable loss AntGain Result Limit Margin [MHz] [dBm] [dBm] [dB] [dBi] [dBm] [dBm] [dB] H 38196 £53.1 426 16 93 449 130 319 V 3819.6 —55.1 —57.0 1.6 93 49.3 130 363 TUV SUD Zacta Ltd Report number: 2101C—16040 Test Report RevFCC—24E2.1 FCC ID: JOYYKCAQ4

Page 24 of 28 10. Frequency Stability 10.1 Measurement procedure [FCC 24.235, 2.1055] The EUT was placed of an inside of an constant temperature chamber as the temperature in the chamber was varied between -30˚C and +50˚C. The temperature was incremented by 10˚C intervals and the unit was allowed to stabilize at each measurement. The frequency drift was measured with the normal Temperature and voltage tolerance and it is presented as the ppm unit. - Test configuration Power splitter Spectrum Wireless Analyzer Attenuator Communication Coaxial cable Coaxial cable Tester EUT Constant Temperature Chamber 10.2 Limit ±2.5ppm TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 25 of 28 10.3 Measurement result Date : March 25, 2016 Temperature : 21.1 [˚C] Humidity : 45.3 [%] Test engineer : Test place : Shielded room No.4 Hikaru Shibata [GSM1900] (Channel: 661) Limit: ±0.00025% = ±2.5ppm Temperatur Measurements Frequency Power Supply Limit e Frequency Tolerance Result [V] [ºC] [Hz] [ppm] [ppm] 25(Ref.) 1,880,000,021 0.00000 ±2.5 Pass 50 1,880,000,012 -0.00453 ±2.5 Pass 40 1,879,999,986 -0.01868 ±2.5 Pass 30 1,880,000,030 0.00498 ±2.5 Pass 20 1,880,000,016 -0.00273 ±2.5 Pass 3.80 10 1,879,999,977 -0.02355 ±2.5 Pass 0 1,880,000,014 -0.00385 ±2.5 Pass -10 1,879,999,986 -0.01863 ±2.5 Pass -20 1,879,999,978 -0.02293 ±2.5 Pass -30 1,879,999,975 -0.02448 ±2.5 Pass 3.230 25 1,880,000,023 0.00121 ±2.5 Pass 4.370 25 1,880,000,020 -0.00032 ±2.5 Pass Calculation; Frequency Tolerance (ppm) = Measurements Frequency (Hz) – Reference Frequency (Hz) / Reference Frequency (Hz) x 1000000 TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 26 of 28 11. Uncertainty of measurement Expanded uncertainties stated are calculated with a coverage Factor k=2. Please note that these results are not taken into account when measurement uncertainty considerations contained in ETSI TR 100 028-0011 determining compliance or non-compliance with test result. Test item Measurement uncertainty Conducted emission at mains port ±3.0dB Radiated emission (9kHz – 30MHz) ±4.4dB Radiated emission (30MHz – 1000MHz) ±4.5dB Radiated emission (1000MHz – 26GHz) ±3.9dB TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 27 of 28 12. Laboratory description 1. Location: TÜV SÜD Zacta Ltd. Yonezawa Testing Center 4149-7 Hachimanpara 5-chome Yonezawa-shi Yamagata 992-1128 Japan Phone: +81-238-28-2880 Fax: +81-238-28-2888 2. Facility filing information: 1) NVLAP accreditation: NVLAP Lab. code: 200306-0 2) VLAC accreditation: Lab. code: VLAC-013 Conducted Conducted Radiated Radiated Site name emission for emission for emission Expiry Date emission mains port telecom port (CMAD) 3m Semi-anechoic chamber - 10m Semi-anechoic chamber No.1 VLAC-013 VLAC-013 Jul. 3, 2017 10m Semi-anechoic chamber No.2 Shielded room No.1 - VLAC-013 - 3) FCC filing: Site name Registration Number Expiry Date Site 3 91065 Oct. 1, 2017 3m Semi-anechoic chamber 10m Semi-anechoic chamber No.1 540072 Feb. 20, 2017 10m Semi-anechoic chamber No.2 Shielded room No.1 4) Industry Canada Oats site filing: Site name Sites on file: Oats 3m/10m Expiry Date Site 3 4224A-3 3m Semi-anechoic chamber 4224A-4 Dec. 3, 2017 10m Semi-anechoic chamber No.1 4224A-5 10m Semi-anechoic chamber No.2 4224A-6 Jan. 15, 2017 5) VCCI site filing: Conducted Conducted Radiated Site name emission for emission for Expiry Date emission mains port telecom port Site 3 R-138 C-134 T-1222 Nov. 16, 2017 3m Semi-anechoic chamber 10m Semi-anechoic chamber No.1 A-0166 Jul. 3, 2017 10m Semi-anechoic chamber No.2 Shielded room No.1 - A-0166 6) TÜV SÜD PS authorization: Authorized as an EMC test laboratory 7) TÜV Rheinland authorization: Authorized as an EMC test laboratory TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04

Page 28 of 28 Appendix A. Test equipment Antenna port conducted test Equipment Company Model No. Serial No. Cal. due Cal. date Spectrum analyzer Agilent Technologies E4440A US44302655 Jun. 30, 2016 Jun. 11, 2015 Microwave cable RS YH_13S5 N/A (S441) May 31, 2016 May 12, 2015 Attenuator Weinschel 56-10 J4993 Nov. 30, 2016 Nov. 12, 2015 Microwave cable SUHNER SUCOFLEX104/1.5m 322087/4 Jul. 31, 2016 Jul. 29, 2015 Power splitter ANRITSU K240B 130129 Jul. 31, 2016 Jul. 12, 2015 Power meter ROHDE&SCHWARZ NRP2 103269 Jun. 20, 2016 Jun. 25, 2015 Power sensor ROHDE&SCHWARZ NRP-Z81 102467 Jun. 20, 2016 Jun. 25, 2015 Wideband radio ROHDE&SCHWARZ CMW500 116338 Apr. 30, 2016 Apr. 2, 2015 frequency tester Operation type temperature Espec PL1KP 14007261 Jan. 31, 2017 Jan. 22, 2016 controlled bath Radiated emission Equipment Company Model No. Serial No. Cal. Due Cal. Date EMI Receiver ROHDE&SCHWARZ ESCI 100764 Aug. 31, 2016 Aug. 21, 2015 Preamplifier ANRITSU MH648A M96057 Jun. 30, 2016 Jun. 30, 2015 Biconical antenna Schwarzbeck VHA9103/BBA9106 2155 Jun. 30, 2016 Jun. 4, 2015 Log periodic antenna Schwarzbeck UHALP9108A 0560 Jun. 30, 2016 Jun. 4, 2015 Attenuator TME CFA-01NPJ-6 N/A (S275) Jun. 30, 2016 Jun. 23, 2015 Attenuator TME CFA-01NPJ-3 N/A (S272) Jun. 30, 2016 Jun. 23, 2015 Spectrum analyzer Agilent Technologies E4440A US40420937 Jul. 31, 2016 Jul. 23, 2015 Dipole antenna Schwarzbeck VHAP 1021 Oct. 31, 2016 Oct. 2, 2015 Dipole antenna Schwarzbeck UHAP 993 Oct. 31, 2016 Oct. 2, 2015 Double ridged guide EMCO 3115 5205 Mar. 31, 2017 Mar. 3, 2016 antenna Attenuator Agilent Technologies 8491B MY39268633 Feb. 28, 2017 Feb. 23, 2016 Double ridged guide EMCO 3115 000058532 Nov. 30, 2016 Nov. 6, 2015 antenna Preamplifier TSJ MLA-100M18-B02-40 1929118 May 31, 2016 May 1, 2015 Attenuator AEROFLEX 26A-10 081217-08 May 31, 2016 May 7, 2015 Signal generator ROHDE&SCHWARZ SMB100A 177525 Jun. 30, 2016 Jun. 19, 2015 Power amplifier R&K CGA020M602-2633R B40240 Mar. 31, 2016 Mar. 23, 2015 Microwave cable SUHNER SUCOFELX102/2m 31648/2 Mar. 31, 2016 Mar. 10, 2015 High pass filter Micro-Tronics HPM50115 004 Jul. 31, 2016 Jul. 12, 2015 High pass filter Wainwright WHKX2.8/18G-6SS 1 Jul. 31, 2016 Jul. 29, 2015 Band rejection filter Micro-Tronics BRC50720 014 Oct. 31, 2016 Oct. 20, 2015 SUCOFLEX104/9m MY30037/4 Oct. 31, 2016 Oct. 23, 2015 SUCOFLEX104/1m MY24610/4 Oct. 31, 2016 Oct. 23, 2015 Microwave cable SUHNER SUCOFLEX104/8m MY30031/4 May 31, 2016 May 29, 2015 SUCOFLEX104/1.5m 322086/4 May 31, 2016 May 29, 2015 Wideband radio ROHDE&SCHWARZ CMW500 126079 Sep. 30, 2016 Sep. 15, 2015 frequency tester PC DELL DIMENSION E521 75465BX N/A N/A Software TOYO Corporation EP5/RE-AJ 0611193/V5.4.011 N/A N/A 3m Semi-anechoic TOKIN N/A N/A (9002-NSA) Apr. 30, 2016 Apr. 27, 2015 chamber 3m Semi-anechoic TOKIN N/A N/A (9002-SVSWR) Apr. 30, 2016 Apr. 27, 2015 chamber Absorber RIKEN PFP30 N/A N/A N/A *: The calibrations of the above equipment are traceable to NIST or equivalent standards of the reference organizations. TÜV SÜD Zacta Ltd. Report number: Z101C-16040 Test Report Rev.FCC-24E2.1 FCC ID: JOYYKCA04


Document Created: 2016-04-04 15:10:29
Document Modified: 2016-04-04 15:10:29
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC