DTS Bluetooth LE report

FCC ID: JOYYAKF-1

Test Report

Download: PDF
FCCID_1991458

Page 1 of 32 TEST REPORT Report number : ZO71C—13156 Issue date : May 23, 2013 The device, as described herewith, was tested pursuant to applicable test procedure and complies with the requirements of; FCC Part15 Subpart C The test results are traceable to the international or national standards. Applicant : KYOCERA Corporation Equipment under test (EUT) : Mobile Phone Model number : YAKF—1 FCC ID :_JOYYAKF—1 Date oftest _: April 18, 19, 24, May 23, 2013 — Test place : TUV SUD Zacta Ltd. Yonezawa Testing Center 4149—7 Hachimanpara 5—chome Yonezawa—shi Yamagata 992—1128 Japan Phone: +81—238—28—2880 Fax: +81—238—28—2888 Test results : Complied The results in this report are applicable only to the equipment tested. This report shall not be re—produced except in full without the written approval of TUV SUD Zacta Ltd. This test report must not be used by client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. Tested by : %;fi( %771//‘/ Chiaki Kanno Tested by : fl?;\(ik; Wfi?%/&/ Taiki Watanabe Authorized by : ,<7/M /W \ Hiroaki Suzuki & Manager of EMC Technical Department nvilad NVLAP LAB CODE 200306—0 TUV SUD Zacta Ltd. ’ Report number: 2071C—13156 Test Report Rev.FCC—C1.0 FCC ID: JOYYAKF—1

Page 2 of 32 Table of contents Page 1. Summary of Test .................................................................................................................4 1.1 Purpose of test ....................................................................................................................................... 4 1.2 Standards ............................................................................................................................................... 4 1.3 List of applied test to the EUT .............................................................................................................. 4 1.4 Modification to the EUT by laboratory................................................................................................. 4 2. Equipment Under Test ........................................................................................................5 2.1 General Description of equipment ....................................................................................................... 5 2.2 EUT information ..................................................................................................................................... 5 2.3 Variation of the family model(s)............................................................................................................ 6 2.4 Operating channels and frequencies .................................................................................................. 6 2.5 Description of Test mode ...................................................................................................................... 6 2.6 Operating mode ..................................................................................................................................... 7 3. Configuration of equipment ...............................................................................................8 3.1 Equipment(s) used................................................................................................................................. 8 3.2 Cable(s) used ......................................................................................................................................... 8 3.3 System configuration ............................................................................................................................ 8 4. 6dB Bandwidth ....................................................................................................................9 4.1 Measurement procedure ....................................................................................................................... 9 4.2 Limit......................................................................................................................................................... 9 4.3 Measurement result ............................................................................................................................... 9 4.4 Trace data ............................................................................................................................................. 10 5. Maximum Peak Output Power .......................................................................................... 11 5.1 Measurement procedure ......................................................................................................................11 5.2 Limit........................................................................................................................................................11 5.3 Measurement result ..............................................................................................................................11 5.4 Trace data ............................................................................................................................................. 12 6. Band Edge Compliance of RF Conducted Emissions....................................................13 6.1 Measurement procedure ..................................................................................................................... 13 6.2 Limit....................................................................................................................................................... 13 6.3 Measurement result ............................................................................................................................. 13 6.4 Trace data ............................................................................................................................................. 14 7. Spurious emissions - Conducted - ..................................................................................15 7.1 Measurement procedure ..................................................................................................................... 15 7.2 Limit....................................................................................................................................................... 15 7.3 Measurement result ............................................................................................................................. 15 7.4 Trace data ............................................................................................................................................. 16 8. Spurious Emissions - Radiated -......................................................................................19 8.1 Measurement procedure ..................................................................................................................... 19 8.2 Calculation method.............................................................................................................................. 20 8.3 Limit....................................................................................................................................................... 20 8.4 Test data................................................................................................................................................ 21 9. Restricted Band of Operation...........................................................................................22 9.1 Measurement procedure ..................................................................................................................... 22 TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 3 of 32 9.2 Limit....................................................................................................................................................... 22 9.3 Measurement Result............................................................................................................................ 22 9.4 Test data................................................................................................................................................ 23 10. Transmitter Power Spectral Density ..............................................................................25 10.1 Measurement procedure ................................................................................................................... 25 10.2 Limit..................................................................................................................................................... 25 10.3 Measurement result ........................................................................................................................... 25 10.4 Trace data ........................................................................................................................................... 26 11.1 Measurement procedure ................................................................................................................... 27 11.2 Calculation method............................................................................................................................ 27 11.3 Limit ..................................................................................................................................................... 27 11.4 Test data .............................................................................................................................................. 28 12. Antenna requirement ......................................................................................................29 13. Uncertainty of measurement ..........................................................................................30 14. Laboratory description ...................................................................................................31 Appendix A. Test equipment ................................................................................................32 TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 4 of 32 1. Summary of Test 1.1 Purpose of test It is the original test in order to verify conformance to FCC Part 15 Subpart C. 1.2 Standards CFR47 FCC Part 15 Subpart C 1.2.1 Test Methods ANSI C63.4-2003, KDB558074 1.2.2 Deviation from standards None 1.3 List of applied test to the EUT Test items Test items Condition Result Section 15.247(a)(2) 6dB Bandwidth Conducted PASS 15.247(b)(3) Maximum Peak Output Power Conducted PASS Band Edge Compliance of RF Conducted 15.247(d) Conducted PASS Emissions 15.247(d) Conducted 15.205 Spurious Emissions PASS Radiated 15.209 15.247(d) 15.205 Restricted Bands of Operation Radiated PASS 15.209 15.247(e) Transmitter Power Spectral Density Conducted PASS 15.207 AC Power Line Conducted Emissions Conducted PASS 1.3.1 Test set up Table-Top 1.4 Modification to the EUT by laboratory None TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 5 of 32 2. Equipment Under Test 2.1 General Description of equipment EUT is the Mobile Phone. 2.2 EUT information Applicant : KYOCERA Corporation Yokohama Office 2-1-1 Kagahara, Tsuzuki-ku Yokohama-shi, Kanagawa, Japan Phone: +81-45-943-6253 Fax: +81-45-943-6314 Equipment under test : Mobile Phone Trade name : Kyocera Model number : YAKF-1 Serial number : N/A EUT condition : Pre-Production Max. frequency : 1.5GHz Power ratings : Battery: DC 3.8V Size : (W) 134 × (D) 66 × (H) 10.9 mm Environment : Indoor and Outdoor use Terminal limitation : -20˚C to 60˚C RF Specification Protocol : Bluetooth 4.0 + EDR Frequency range : 2402MHz-2480MHz Number of RF : 40 Channels Channels Modulation method/ : GFSK (1Mbps) Data rate Channel separation : 2MHz Output power : 0.575mW Antenna type : Internal antenna Antenna gain : 0dBi TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 6 of 32 2.3 Variation of the family model(s) Not applicable 2.4 Operating channels and frequencies Channel Frequency [MHz] Channel Frequency [MHz] 0 2402 20 2442 1 2404 21 2444 2 2406 22 2446 3 2408 23 2448 4 2410 24 2450 5 2412 25 2452 6 2414 26 2454 7 2416 27 2456 8 2418 28 2458 9 2420 29 2460 10 2422 30 2462 11 2424 31 2464 12 2426 32 2466 13 2428 33 2468 14 2430 34 2470 15 2432 35 2472 16 2434 36 2474 17 2436 37 2476 18 2438 38 2478 19 2440 39 2480 2.5 Description of Test mode The EUT had been tested under operating condition. There are three channels have been tested as following: Tested Channel Frequency [MHz] Low 2402 Middle 2440 High 2480 The pre-test has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates. Tested Channel Modulation Type Data Rate Low, Middle, High GFSK 1Mbps The field strength of spurious emissions was measured at each position of all three axis X, Y and Z to compare the level, and the maximum noise. The worst emission was found in X axis and the worst case recorded. TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 7 of 32 2.6 Operating mode [Tx mode] i) Test program setup to the DM tool ii) Select a Test mode Operating frequency: Channel Low: 2402MHz, Channel Middle: 2440MHz, Channel High: 2480MHz iii) Start test mode [Rx mode] i) Test program setup to the DM tool ii) Select a Test mode Operating frequency: Channel Low: 2402MHz, Channel Middle: 2440MHz, Channel High: 2480MHz iii) Start test mode TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 8 of 32 3. Configuration of equipment 3.1 Equipment(s) used No. Equipment Company Model No. Serial No. FCC ID / DoC Comment 1 Mobile Phone KYOCERA YAKF-1 N/A JOYYAKF-1 EUT 2 AC Adapter SoftBank AC01-MU-K N/A - * *: AC power line Conducted Emission Test. 3.2 Cable(s) used No. Cable Length[m] Shield Connector Comment a DC cable 1.5 No Plastic * *: AC power line Conducted Emission Test. 3.3 System configuration 1. Mobile Phone (EUT) a. # 2. AC Adapter AC 120V USB 60Hz # : Un-detachable cable Note1: Numbers assigned to equipment or cables on this diagram correspond to the list in “3.1 Equipment(s) used” and “3.2 Cable(s) used”. TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 9 of 32 4. 6dB Bandwidth 4.1 Measurement procedure [FCC 15.247(a)(2), KDB558074] The bandwidth at 6dB down from the highest inband spectral density is measured with a spectrum analyzer connected to the antenna terminal, while EUT is operating in transmission mode at the appropriate center frequency. The spectrum analyzer is set to; - RBW=100kHz, VBW=300kHz, Span=3MHz, Sweep=auto, Detector=Peak, Trace mode=Max hold The EUT was set to operate with following conditions. - Channel Low: 2402MHz, Channel Middle: 2440MHz, Channel High: 2480MHz The test mode of EUT is as follows. - Tx mode - Test configuration Spectrum EUT Attenuator Analyzer Coaxial cable 4.2 Limit The minimum permissible 6dB bandwidth is 500kHz. 4.3 Measurement result Date : Apr. 18, 2013 Test personnel : Temperature : 20.0 [˚C] Humidity : 50.0 [%] Tested by : Test place : Shielded room Chiaki Kanno Channel Frequency [MHz] 6dB bandwidth [MHz] Low 2402 0.708 Middle 2440 0.712 High 2480 0.710 TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 10 of 32 4.4 Trace data Channel Low Channel Middle Channel High TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 11 of 32 5. Maximum Peak Output Power 5.1 Measurement procedure [FCC 15.247(b)(3), 15.31(e), KDB558074] The peak power is measured with a spectrum analyzer connected to the antenna terminal, while EUT is operating in transmission mode at the appropriate center frequency. The spectrum analyzer is set to; — RBW=1MHz, VBW=8MHz, Span=3MHz, Sweep=auto, Detector=Peak, Trace mode=Max hold The EUT was set to operate with following conditions. — Channel Low: 2402MHz, Channel Middle: 2440MHz, Channel High: 2480MHz The test mode of EUT is as follows. — Tx mode — Test configuration Spectrum EUT Attenuator Analyzer Coaxial cable 5.2 Limit 1W (1000mW) or less 5.3 Measurement result Date : Apr. 18, 2013 Test personnel Temperature : 20.0 [C] Humidity : 50.0 [%] Tested by : Test place : Shielded room Chiaki Kanno . Peak 20L Frequency Reading Factor Level Limit Channel Output Power Result (MHz) (dBm) (dB) (dBm) (mW) {mW) Low 2402 —14.11 11.37 —2.74 0.532 1000 PASS Middle 2440 —14.33 11.37 —2.96 0.506 1000 PASS High 2480 ~13.77 11.37 —2.40 0.575 1000 PASS Calculation; Reading (dBm) + Factor (dB) = Level (dBm) 19e Ec CEmm io P= 10 aximim Pea wer (mv\,) TUV SUD Zacta Ltd Report number: 20710—13156 Test Report RevFCC—C1.0 FCC ID: JOYYAKE—A1

Page 12 of 32 5.4 Trace data Channel Low Channel Middle Channel High TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 13 of 32 6. Band Edge Compliance of RF Conducted Emissions 6.1 Measurement procedure [FCC 15.247(d), KDB558074] The Band Edge is measured with a spectrum analyzer connected to the antenna terminal, while EUT is operating in transmission mode at the appropriate center frequency. The spectrum analyzer is set to; - RBW=100kHz, VBW=100kHz, Span=Arbitrary setting, Sweep=auto, Detector=Peak, Trace mode=Max hold The EUT was set to operate with following conditions. - Channel Low: 2402MHz, Channel High: 2480MHz The test mode of EUT is as follows. - Tx mode - Test configuration Spectrum EUT Attenuator Analyzer Coaxial cable 6.2 Limit In any 100kHz bandwidth outside the frequency band the radio frequency power that is produced by the intentional radiator shall be at least 20dB below that in the 100kHz bandwidth within the band that contains the highest level of the desired power. 6.3 Measurement result Date : Apr. 18, 2013 Test personnel : Temperature : 20.0 [˚C] Humidity : 50.0 [%] Tested by : Test place : Shielded room Chiaki Kanno RF Band-edge Band-edge Difference Frequency Power Limit Channel Frequency Level Level Result (MHz) Level (dBm) (MHz) (dBm) (dBm) (dBm) Low 2402.00 -10.42 2389.36 -75.94 65.52 At least 20dB below from peak of RF PASS High 2480.00 -9.89 2483.55 -75.98 66.09 At least 20dB below from peak of RF PASS TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 14 of 32 6.4 Trace data Channel Low Channel High TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 15 of 32 7. Spurious emissions - Conducted - 7.1 Measurement procedure [FCC 15.247(d), KDB558074] The spurious emissions (Conducted) are measured with a spectrum analyzer connected to the antenna terminal, while EUT is operating in transmission mode at the appropriate center frequency. The spectrum analyzer is set to; - RBW=100kHz, VBW=300kHz, Span=Arbitrary setting, Sweep=auto, Detector=Peak, Trace mode=Max hold The EUT was set to operate with following conditions. - Channel Low: 2402MHz, Channel Middle: 2440MHz, Channel High: 2480MHz The test mode of EUT is as follows. - Tx mode - Test configuration Spectrum EUT Attenuator Analyzer Coaxial cable 7.2 Limit In any 100kHz bandwidth outside the frequency band the radio frequency power that is produced by the intentional radiator shall be at least 20dB below that in the 100kHz bandwidth within the band that contains the highest level of the desired power. 7.3 Measurement result Date : Apr. 18, 2013 Test personnel : Temperature : 20.0 [˚C] Humidity : 50.0 [%] Tested by : Test place : Shielded room Chiaki Kanno Frequency Limit Channel Results Chart Result [MHz] [dB] Low 2402 At least 20dB below from peak of RF See the trace Data PASS Middle 2440 At least 20dB below from peak of RF See the trace Data PASS High 2480 At least 20dB below from peak of RF See the trace Data PASS TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 16 of 32 7.4 Trace data Channel Low 30MHz-1GHz 1GHz-5GHz 5GHz-10GHz 10GHz-15GHz 15GHz-20GHz 20GHz-25GHz TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 17 of 32 Channel Middle 30MHz-1GHz 1GHz-5GHz 5GHz-10GHz 10GHz-15GHz 15GHz-20GHz 20GHz-25GHz TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 18 of 32 Channel High 30MHz-1GHz 1GHz-5GHz 5GHz-10GHz 10GHz-15GHz 15GHz-20GHz 20GHz-25GHz TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 19 of 32 8. Spurious Emissions - Radiated - 8.1 Measurement procedure [FCC 247(d), 15,205, 15.209] Test was applied by following conditions. Test method : ANSI C63.4 Frequency range : 9kHz to 25GHz Test place : 3m Semi-anechoic chamber EUT was placed on : FRP table / (W)2.0m × (D)1.0m × (H)0.8m Antenna distance : 3m Test receiver setting Below 1GHz - Detector : Average (9kHz-90kHz, 110kHz-490kHz), Quasi-peak - Bandwidth : 200Hz, 120kHz Spectrum analyzer setting Above 1GHz - Peak : RBW=1MHz, VBW=1MHz, Span=0Hz, Sweep=auto - Average : RBW=1MHz, VBW=10Hz, Span=0Hz, Sweep=auto Display mode=Linear Radiated emission measurements are performed at 3m distance with the broadband antenna (Loop antenna, TRILOG antenna and Double ridged guide antenna). The antenna is positioned both the horizontal and vertical planes of polarization and height is varied 1m to 4m and stopped at height producing the maximum emission. As for the Loop antenna, it is positioned with its plane vertical, and the center of the Loop antenna is 1m above the ground plane. The EUT is Placed on a turntable, which is 0.8m above ground plane. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. The test results represent the worst case emission for each emission with manipulating the EUT, support equipment, interconnecting cables and varying the mode of operation. Sufficient time for the EUT, support equipment, and test equipment are allowed in order for them to warm up to their normal operating condition. The EUT was set to operate with following conditions. - Channel Low: 2402MHz, Channel Middle: 2440MHz, Channel High: 2480MHz The test mode of EUT is as follows. - Tx mode, Rx mode - Test configuration TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 20 of 32 8.2 Calculation method [9kHz to 150kHz] Emission level = Reading + (Ant. factor + Cable system loss ) Margin = Limit – Emission level [150kHz to 25GHz] Emission level = Reading + (Ant. factor + Cable system loss – Amp. Gain) Margin = Limit – Emission level 8.3 Limit Frequency Field strength Distance [MHz] [uV/m] [dBuV/m] [m] 0.009-0.490 2400 / F [kHz] 20logE [uV/m] 300 0.490-1.705 24000 / F [kHz] 20logE [uV/m] 30 1.705-30 30 29.5 30 30-88 100 40.0 3 88-216 150 43.5 3 216-960 200 46.0 3 Above 960 300 54.0 3 Note: 1. The lower limit shall apply at the transition frequencies. 2. Emission level [dBuV/m] = 20log Emission [uV/m] 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition modulation. TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 21 of 32 8.4 Test data Date : Apr. 19, 2013 Test personnel : Temperature : 21.0 [˚C] Humidity : 31.3 [%] Tested by : Test place : 3m Semi-anechoic chamber Chiaki Kanno Channel Low Channel Middle Channel High Note: 1. Emission Level (Margin) = Limit - [Reading + Factor ( Antenna + Cable – Amp)] 2. No emission were detected in frequency range 9kHz to 1000MHz at the 3 meters distance. 3. No emission was detected in the receive mode. TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 22 of 32 9. Restricted Band of Operation 9.1 Measurement procedure [FCC 247(d), 15,205, 15.209] Test was applied by following conditions. Test method : ANSI C63.4 Test place : 3m Semi-anechoic chamber EUT was placed on : FRP table / (W)2.0m × (D)1.0m × (H)0.8m Antenna distance : 3m Spectrum analyzer setting - Peak : RBW=1MHz, VBW=1MHz, Span=Arbitrary setting, Sweep=auto - Average : RBW=1MHz, VBW=10Hz, Span=Arbitrary setting, Sweep=auto Display mode=Linear Radiated emission measurements are performed at 3m distance with the broadband antenna (Double ridged guide antenna). The antenna is positioned both the horizontal and vertical planes of polarization and height is varied 1m to 4m and stopped at height producing the maximum emission. The EUT is Placed on a turntable, which is 0.8m above ground plane. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. The test results represent the worst case emission for each emission with manipulating the EUT, support equipment, interconnecting cables and varying the mode of operation. Sufficient time for the EUT, support equipment, and test equipment are allowed in order for them to warm up to their normal operating condition. The EUT was set to operate with following conditions. - Channel Low: 2402MHz, Channel High: 2480MHz The test mode of EUT is as follows. - Tx mode - Test configuration 9.2 Limit Emission at the boundary of the restricted band provided by 15.205 shall be lower than 15.209 limit. 9.3 Measurement Result Channel Frequency [MHz] Results Chart Result Low 2402 See the Trace Data Pass High 2480 See the Trace Data Pass TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 23 of 32 9.4 Test data Date : Apr. 24, 2013 Test personnel : Temperature : 21.5 [˚C] Humidity : 33.5 [%] Tested by : Test place : 3m Semi-anechoic chamber Chiaki Kanno Channel Low Horizontal Peak Average Vertical Peak Average TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 24 of 32 Channel High Horizontal Peak Average Vertical Peak Average TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 25 of 32 10. Transmitter Power Spectral Density 10.1 Measurement procedure [FCC 15.247(d), KDB558074] The peak power is measured with a spectrum analyzer connected to the antenna terminal, while EUT is operating in transmission mode at the appropriate center frequency. The spectrum analyzer is set to; - RBW=3kHz, VBW=10kHz, Span=1MHz, Sweep=Auto, Detector=Peak, Trace mode=Max hold The EUT was set to operate with following conditions. - Channel Low: 2402MHz, Channel Middle: 2440MHz, Channel High: 2480MHz The test mode of EUT is as follows. - Tx mode - Test configuration Spectrum EUT Attenuator Analyzer Coaxial cable 10.2 Limit The peak power spectral density shall not be greater than 8dBm in any 3kHz band. 10.3 Measurement result Date : Apr. 18 2013 Test personnel : Temperature : 20.0 [˚C] Humidity : 50.0 [%] Tested by : Test place : Shielded room Chiaki Kanno Frequency Reading Factor Level Limit Margin Channel Result (MHz) (dBm) (dB) (dBm) (dBm) (dBm) Low 2402.00 -24.03 11.37 -12.66 8.00 20.66 PASS Middle 2440.00 -24.05 11.37 -12.68 8.00 20.68 PASS High 2480.00 -23.48 11.37 -12.11 8.00 20.11 PASS Calculation; Transmitter Power Spectral Density Level (Margin) = Limit – (Reading + Factor) TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 26 of 32 10.4 Trace data Channel Low Channel Middle Channel High TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 27 of 32 11. AC Power Line Conducted Emissions 11.1 Measurement procedure [FCC 15.207] Test was applied by following conditions. Test method : ANSI C63.4 Frequency range : 0.15MHz to 30MHz Test place : 10m Semi-anechoic chamber EUT was placed on : FRP table / (W)2.0m × (D)1.0m × (H)0.8m Vertical Metal Reference Plane : (W)2.0m × (H)2.0m 0.4m away from EUT Test receiver setting - Detector : Quasi-peak, Average - Bandwidth : 9kHz EUT and peripherals are connected to 50Ω/50μH Line Impedance Stabilization Network (LISN) which are connected to reference ground plane, and are placed 80cm away from EUT. Excess of AC power cable is bundled in center. LISN for peripheral is terminated in 50Ω. EUT operating mode is selected to emit the maximum noise. Overall frequency range is investigated with spectrum analyzer using peak detector. Maximum emission configuration is determined by manipulating the EUT, peripherals, interconnecting cables. Then, emission measurements are performed with test receiver in above setting to each current-carrying conductor of the mains port. Sufficient time for EUT, peripherals and test equipment is provided in order for them to warm up to their normal operating condition. If the average limit is met when using a quasi-peak detector receiver, the EUT shall be deemed to meet both limits. - Test configuration 11.2 Calculation method Emission level = Reading + (LISN. factor + Cable system loss) Margin = Limit – Emission level 11.3 Limit Frequency Limit [MHz] QP [dBuV] AV [dBuV] 0.15-0.5 66-56* 56-46* 0.5-5 56 46 5-30 60 50 *: The limit decreases linearly with the logarithm of the frequency in the range 0.15MHz to 0.5MHz. TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 28 of 32 11.4 Test data TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 29 of 32 12. Antenna requirement According to FCC section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The antenna is a special antenna mounted inside of the EUT. Therefore, the EUT complies with the antenna requirement of FCC section 15.203. TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 30 of 32 13. Uncertainty of measurement Expanded uncertainties stated are calculated with a coverage Factor k=2. Please note that these results are not taken into account when determining compliance or non-compliance with test result. Test item Measurement uncertainty Conducted emission at mains port ±3.0dB Radiated emission (9kHz – 30MHz) ±4.4dB Radiated emission (30MHz – 1000MHz) ±4.5dB Radiated emission (1000MHz – 26GHz) ±3.9dB TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 31 of 32 14. Laboratory description 1. Location: TÜV SÜD Zacta Ltd. Yonezawa Testing Center 4149-7 Hachimanpara 5-chome Yonezawa-shi Yamagata 992-1128 Japan Phone: +81-238-28-2880 Fax: +81-238-28-2888 2. Facility filing information: 1) NVLAP accreditation: NVLAP Lab. code: 200306-0 2) VLAC accreditation: Lab. code: VLAC-013 Conducted Conducted Radiated Radiated Site name emission for emission for emission Expiry Date emission mains port telecom port (CMAD) 10m Semi-anechoic chamber VLAC-013 VLAC-013 3m Semi-anechoic chamber - Jul. 3, 2013 Shielded room No.1 - VLAC-013 - 3) FCC filing: Site name Registration Number Expiry Date Site 2 91065 Oct.31, 2014 Site 3 10m Semi-anechoic chamber 3m Semi-anechoic chamber 540072 Jan. 9, 2016 Shielded room No.1 4) Industry Canada Oats site filing: Site name Sites on file: Oats 3m/10m Expiry Date Site 2 4224A-2 Site 3 4224A-3 Jan. 23, 2015 3m Semi-anechoic chamber 4224A-4 10m Semi-anechoic chamber 4224A-5 5) VCCI site filing: Conducted Conducted Radiated Site name emission for Expiry Date emission for Expiry Date emission mains port telecom port Site 2 R-137 C-133 T-1221 Nov. 16, 2014 Nov. 28, 2014 Site 3 R-138 C-134 T-1222 R-2480 C-2722 T-1474 Jul. 3, 2013 10m Semi-anechoic chamber G-81 - - - R-2481 C-2723 Jul. 3, 2013 T-1475 Jul. 3, 2013 3m Semi-anechoic chamber G-82 - - - Shielded room No.1 - C-2724 T-1476 Jul. 3, 2013 6) TÜV SÜD PS authorization: Authorized as an EMC test laboratory 7) TÜV Rheinland authorization: Authorized as an EMC test laboratory TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1

Page 32 of 32 Appendix A. Test equipment [Antenna port conducted test] Equipment Company Model No. Serial No. Cal. due Cal. date Spectrum analyzer Agilent Technologies E4440A US40420937 Oct. 2013 Oct. 19, 2012 Microwave cable RS YH_13S5 N/A (S403) May 2013 May 10, 2012 Attenuator Weinschel 56-10 J4180 Nov. 2013 Nov. 12, 2012 Radiated emission Equipment Company Model No. Serial No. Cal. Due Cal. Date EMI Receiver ROHDE&SCHWARZ ECSI 100764 Jul. 2013 Jul. 6, 2012 Preamplifier ANRITSU MH648A M96057 Jun. 2013 Jun. 12, 2012 Loop antenna ROHDE&SCHWARZ HFH2-Z2 892246/010 Sep. 2013 Sep. 14, 2012 TRILOG Antenna Schwarzbeck VULB9160 9160-3218 May 2014 May 2, 2012 Attenuator TME CFA-01NPJ-6 N/A (S274) Jun. 2013 Jun. 12, 2012 Spectrum analyzer Agilent Technologies E4447A MY46180188 Mar. 2014 Mar. 8, 2013 Preamplifier Agilent Technologies 8449B 3008A1008 Dec. 2013 Dec. 9, 2012 Double ridged guide EMCO 3115 4328 Jan. 2014 Jan. 21, 2013 antenna Attenuator AEROFLEX 40A-03 081217-20 Feb. 2014 Feb. 23, 2013 Broad-Band Horn Schwarzbeck BBHA9170 BBHA9170189 Apr. 2013 Apr. 20, 2010 Antenna Preamplifier TSJ MLA-1840-B03-35 1240332 Apr. 2013 Apr. 20, 2010 SUCOFLEX104/9m 346316/4 Oct. 2013 Oct. 6, 2012 SUCOFLEX104/1m 322084/4 Oct. 2013 Oct. 6, 2012 Microwave cable SUHNER SUCOFLEX104/1.5m 317226/4 Oct. 2013 Oct. 6, 2012 SUCOFLEX104/7m 41625/6 Oct. 2013 Oct. 6, 2012 PC DELL DIMENSION E521 75465BX N/A N/A Software TOYO Corporation EP5/RE-AJ 0611193/V5.3.61 N/A N/A 3m Semi-anechoic chamber TOKIN N/A N/A (9002-NSA) May 2013 May 19, 2012 Conducted emission at mains port Equipment Company Model No. Serial No. Cal. due Cal. date EMI Receiver ROHDE&SCHWARZ ECSI 100764 Jul. 2013 Jul. 6, 2012 Attenuator HUBER+SUHNER 6810.01.A N/A (S411) Jun. 2013 Jun. 25, 2012 Line impedance Kyoritsu Electrical stabilization network KNW-407F 8-2003-1 Mar. 2014 Mar. 12, 2013 Works, Ltd. for EUT Coaxial cable FUJIKURA 5D-2W/4m N/A (S350) Feb. 2014 Feb. 4, 2013 Coaxial cable FUJIKURA 5D-2W/1m N/A (S193) Feb. 2014 Feb. 4, 2013 Coaxial cable SUHNER RG214/U/10m N/A (S194) Feb. 2014 Feb. 4, 2013 PC DELL DIMENSION 75465BX N/A N/A TÜV SÜD Zacta Ltd. Report number: Z071C-13156 Test Report Rev.FCC-C1.0 FCC ID: JOYYAKF-1


Document Created: 2013-05-30 15:09:36
Document Modified: 2013-05-30 15:09:36
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC