revised test report

FCC ID: JOYKWB2000

Test Report

Download: PDF
FCCID_191260

FCC ID:JOYKWB2000 September 26, 2000 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attention: Applications Examiner Applicant: Kyocera Corporation 2-1-1 Kagahara, Tsuzuki-ku, Yokohama-shi 224 Japan Equipment: PHS-WLL Base Station (BS), KWB-2000 FCC ID: JOYKWB2000 Specification: for a 47 CFR 24 Licensed Certification Dear Examiner: The following application for Grant of Equipment Authorization is presented on behalf of Kyocera Corporation. for the Licensed Certification of their Model: KWB-2000. Enclosed, please find a complete data and documentation package demonstrating that this device complies with the technical requirements of 47 CFR 24. If you have any questions, please contact the undersigned, who is authorized to act as Agent. Sincerely, Chris Harvey, Director EMC Laboratory MET Laboratories, Inc.

FCC ID:JOYKWB2000 MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 914 WEST PATAPSCO AVENUE ! BALTIMORE, MARYLAND 21230-3432 ! PHONE (410) 354-3300 ! FAX (410) 354-3313 ENGINEERING TEST REPORT in support of the Application for Grant of Equipment Authorization EQUIPMENT: PHS-WLL Base Station (BS) KWB-2000 FCC ID: JOYKWB2000 Specification: 47 CFR 24 On Behalf of the Applicant: Kyocera Corporation 2-1-1, Kagahara, Tsuzuki-ku Yokohama-shi 224 Japan Manufacturer: Kyocera Corporation 2-1-1, Kagahara, Tsuzuki-ku Yokohama-shi 224 Japan Manufacturer’s Representative Mr.Nobuyuki hayashida Test Date(s): August 14-25, 2000 ENGINEERING STATEMENT I ATTEST: the measurements shown in this report were made in accordance with the procedures indicated, and that the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements. On the basis of the measurements made, the equipment tested is capable of operation in accordance with the requirements of Part 24 of the FCC Rules under normal use and maintenance. _____________________________ Liming Xu Project Engineer, MET Laboratories EMC1366A -2- September 26, 2000

FCC ID:JOYKWB2000 1.0 INTRODUCTION The following data is presented on behalf of the Applicant, Kyocera Corporation, as verification of the compliance of the Kyocera KWB-2000 to the requirements of 47 CFR 24. 2.0 TEST SITE All testing was conducted at AKZO KASHIMA MATSUDA Site. The radiated emissions measurements were performed on a three-meter open area test site (OATS). A complete site description is on file with the FCC Laboratory Division as 31040/SIT/AKZO and also on file with the NVLAP No. 100290-4. 3.0 TEST EQUIPMENT USED Manufacturer Equipment Calibration Due Date @ time of Cal. Interval testing Hewlett Packard 8563E Spectrum Analyzer 04/04/01 annual HP Pre-Amp 8449B 4/21/01 annual A.R.A. BB Antenna LPB-2513/A 05/15/01 annual EMCO Double Ridge Guided Horn 04/05/01 annual SUHNER 3dB Attenuator 6803.17.B 01/14/01 annual ADVANTEST R3271A Spectrum Analyzer 01/31/02 annual ADVANTEST R5363 Frequency Counter 09/30/01 annual 4.0 EQUIPMENT UNDER TEST CONFIGURATION The WLL Base Station (BS) was configured with DC power supply modules and an external PC to program the EUT to output a PHS RF signal. The EUT with host external computer was configured for maximum signal gain and bandwidth. The EUT was operated in a manner representative of the typical usage of the equipment. During all testing, system components were manipulated within the confines of typical usage to maximize each emission. 5.0 TEST TYPE(S) 5.1 Radiated Emissions: 47 CFR2.1053, , 24.238(a) 5.2 Occupied Bandwidth: 47 CFR2.1049 5.3 RF Power Output: 47 CFR 2.1046, 24.232(a), (c) 5.4 Spurious Emission at Antenna Terminals: 47 CFR 2.1051, 24.238(a) 5.5 Spurious Emission at Antenna Terminals at Frequency Block edges +/- 1 MHz, 47 CFR 2.1051, 24.238(b) 5.6 Frequency Stability over temperature variations: 47 CFR 2.1055(a)(1) 5.7 Frequency Stability over variations in supply voltage: 47 CFR 2.1055(d)(1) 5.8 AC Line Conducted Emissions: 47 CFR 15.107 5.9 Modulation Characteristics: 47 CFR 2.1047(a) EMC1366A -3- September 26, 2000

FCC ID:JOYKWB2000 6.0 TEST RESULTS 6.1 TEST TYPE: Radiated Emissions 6.1.1 TECHNICAL SPECIFICATION: 2.1053; 24.238(a) 6.1.2 TEST DATE(S): 8/21/00 6.1.3 MEASUREMENT PROCEDURES: As required by §2.1053, field strength of spurious radiation measurements were made in accordance with the general procedures of ANSI C63.4-1992 "Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz". Preliminary radiated emission measurements were performed inside a shielded chamber with all digital signal generators on and terminated. The frequency list from the preliminary measurements was used as a guide for making additional measurements on a 3 meter open area test site. The outcome of these additional measurements is used to determine if formal substitution-method measurements are deemed necessary. The unit was scanned over the frequency range of the system operation frequency to 19 GHz. The Radiated Spurious Emissions Limit is obtained by the following: Based on an output power (as measured at the output of the Amplifier) of 0.028 watts: Po = 0.028 W the radiated power level of all spurious emissions must be attenuated by at least 43 + 10log(Po) below Po, yielding: Po& [43 % 10Log(0.028)] ' & 13dBm Mathematical calculations indicate that these measurements yield radiated power levels greater than 30 dB below the -13 dBm limit for spurious emissions from the transmitter portion of the EUT calculated above. Therefore there was no need to perform full substitution-method measurements for these detectable emissions. EMC1366A -4- September 26, 2000

FCC ID:JOYKWB2000 6.1.4 RESULTS: Frequency Polarity Height Raw A.C.F. D.C.F. Corrected (MHz) (m) Amplitude (dB) (dB) Amplitude (dBm) (dBm) 15216.00 V 1 -71.4 22.4 0 -49 5706.00 H 1 -72.7 13.3 0 -59.4 3804.00 H 1 -72.7 9.5 0 -63.2 3804.66 H 1 -77 9.5 0 -67.5 3804.66 V 1 -65.5 9.5 0 -56 5707.30 H 1 -77 13.3 0 -63.7 5707.30 V 1 -77.1 13.3 0 -63.8 7609.62 H 1 -77.7 15.3 0 -62.4 7609.62 V 1 -77.5 15.3 0 -62.2 13316.31 H 1 -78.2 20.5 0 -57.7 13316.31 V 1 -78.2 20.5 0 -57.7 19023.30 H 1 -76.6 21.4 0 -55.2 19023.30 V 1 -76.6 21.4 0 -55.2 Equipment meets the specifications of 2.1053; 24.238(a) Mathematical calculations indicate that these measurements yield radiated power levels greater than 30 dB below the -13 dBm limit for spurious emissions from the transmitter portion of the EUT. Therefore there was no need to perform full substitution-method measurements for these detectable emissions. EMC1366A -5- September 26, 2000

FCC ID:JOYKWB2000 Photograph of Radiated Emissions Test Configuration EMC1366A -6- September 26, 2000

FCC ID:JOYKWB2000 6.2 TEST TYPE: Occupied Bandwidth 6.2.1 TECHNICAL SPECIFICATION: 47CFR2.1049 6.2.2 TEST DATE(S): 8/16/00 6.2.3 MEASUREMENT PROCEDURES: As required by §2.1049 of CFR 47, occupied bandwidth measurements were made on the EUT (BS). The EUT was configured to transmit an PHS modulated carrier signal. Using a bandwidth of 3kHz, we determined the occupied bandwidth of the emission at the center of the selectable channel range. 6.2.4 RESULTS: Equipment complies with Section 2.1049. Plots of the occupied bandwidth, as measured at the RF output port follows: EMC1366A -7- September 26, 2000

FCC ID:JOYKWB2000 6.3 TEST TYPE: RF Power Output 6.3.1 TECHNICAL SPECIFICATION: 47CFR2.1046 and 24.232(a), (c) 6.3.2 TEST DATE(S): 8/16/00 6.3.3 MEASUREMENT PROCEDURES: As required by §2.1046 of CFR 47, RF power output measurements were made at the RF output terminals using a spectrum analyzer. This test was performed with carrier modulated by an PHS modulation signal. Plots of the RF output Power level of the Digitally modulated carrier, as measured at the RF output are included on the following page . 6.3.4 RESULTS: Equipment complies with 47CFR 2.1046 and 24.232(a). The EUT (BS) does not exceed 100 W ( or 50 dBm) at the carrier frequency. Photograph of Antenna Conducted Spurious Emissions and RF Power Output Test Configuration EMC1366A -8- September 26, 2000

Base Station Pover Outout at Center of Authorized Band Th Auy 17 1420 4t 2000 REF 23.0 dn ATT 30 a8 Xbvier 8plank 1008/ l 7 T 1 T ¢A wakea f f 150039 Oir| we L1 I IZL] i.63 dan t.ovese ofr— { 1 fo4—~— U W ILXNO_LIT T] | B / | 11| | | ie us L & 11 6 ~ [ 4 use REH | 1 ie |— es on 1 We , t #. g hokL1 | d cexten 1.90235 o# soan 20.00 Mz Emcimn <o onpmamint cu, cnd

FCC ID:JOYKWB2000 6.4 TEST TYPE: Spurious Emissions at Antenna Terminals 6.4.1 TECHNICAL SPECIFICATION: 2.1051; 24.238(a) 6.4.2 TEST DATE(S): 8/16/00 6.4.3 MEASUREMENT PROCEDURES: As required by §2.1051 of CFR 47, spurious emissions at antenna terminal measurements were made at the RF output terminals using a 50 S attenuator and spectrum analyzer set for a 100 kHz bandwidth. This test was performed with Digitally modulated carrier signals. The Digital signal generator was adjusted for continuous transmit on frequencies in both the uplink and down-link frequency bands. The frequency spectrum was investigated from 9.0 KHz to 20 GHz. For measuring emissions above 2 GHz, a high-pass filter was used to eliminate the fundamental transmit frequency to prevent possible saturation effects on the front end of the spectrum analyzer. 6.4.4 RESULTS: Equipment complies with Section 2.1051and 24.238(a) SUMMARY OF SPURIOUS EMISSIONS AT ANTENNA TERMINALS Frequency Range Emission Emission Level Limit (GHz) Frequency (dBm) (dBm) (GHz) 0 - 2.9 2.453 -49.5 -13.1 2.9 - 7.0 3.937 -49.73 -13.1 7.0 - 15.0 10.211 -42.94 -13.1 15.0 - 20.0 19.179 -37.56 -13.1 The following plots are included to illustrate compliance with the requirements of 47 CFR Part 24.238(a): EMC1366A - 10 - September 26, 2000

Base Station Gorducted Spurious Enissions at antemna terninals Th Aug 17 1t t04 2000 REF 29.0 dn ATT 30 08 Aviev 8platk 1008/ waken _~36.50 0 START 0 iz STOP 2.900 3z

Base Station Gonducted Spurious Emissions at antemna terninals ns g3.0 dgn To Aug 171uacite 5006plan 2000 ATT 30 as $* P[CC }— |——ason wacea 300 kiz SiP START 2.900 6iz STOP 7.000 6iz

Base Station Gonducted Spurious Enissions at. antemna terminals Tho dug 17 145638 2000 ReF 23.0 dn ATT 30 08 Aurite 6plank 1008/ f Snb [ ) 4 1J . waken [* "—? r*fi‘f—@rffi*fifir L. |__| [~pee ob RO | Vgoxfii efi mOkmk~1~*t oo—4—i—1 . l—4..!— dissihcods olcdd STaRT 7.000000000 Giiz STOP 15.000 6iz msny d

Base Station Conducted Spurious Enissions at antema terninals REF ;3 .0 don 1008 vak , k | | 800l —t—f—i—— feer %. L[ I_} inelccadens STaRT 15.000000000 Gz STOP 20.000 Gitz

FCC ID:JOYKWB2000 6.5 TEST TYPE: Spurious Emissions at Antenna Terminals at Block Edges +/- 1 MHz 6.5.1 TECHNICAL SPECIFICATION: 2.1051; 24.238(b) 6.5.2 TEST DATE(S): 8/16/00 6.5.3 MEASUREMENT PROCEDURES: As recommended in FCC Part 24, 1% of the 26dB bandwidth was chosen to measure the peak of any emission inside the 1.0 MHz frequency band adjacent to each frequency block edge. All other frequencies were measured using a 1.0 MHz RBW. The unit was exercised using signal types required by §2.1049. 6.5.4 Results: Modulation products outside of this band are attenuated at least 43 + 10 Log (P) below the level of the modulated carrier. A Plot of the spurious emissions at +/- 1 MHz around the transmit frequency, as measured at the antenna port, appears on the following page. SPURIOUS EMISSION FREQUENCY BLOCKS 1895 MHz-1910 MHz Plots of the spurious emissions as measured at the extremes of each frequency block appear on the following pages. EMC1366A - 15 - September 26, 2000

Buse Station Sporious Entssions at Frequency Block edees +/3ite M side of Block 6 To Aug 17 1628 12 2000 REF 20.0 dBn TT 30 0 _ A.gie8blark 1008/ m waker | —L * 4 1 _A _L_L_L_] L. CENTER 1.910000 6iz SPANL 6.00 W#iz

Base Station Sporious Entssions at Freqvency Block edees +/—3ie Lo side of Block C Tho Aug 17 16 2% 1t 200 ageo0.0 on ATTPSE 30 08 L Xovien 6plank Nss EL 7777% wakea ""Posrzes ( | | in ; { Peinn rmprelenne [ Ees oo _ 1 CENTER 1.89500 6iz SPAN 6.00 1iz

FCC ID:JOYKWB2000 6.6 TEST TYPE: Frequency Stability over Temperature Variations 6.6.1 TECHNICAL SPECIFICATION: 2.1055(a)(1) 6.6.2 TEST DATE(S): 8/17/00 6.6.3 MEASUREMENT PROCEDURES: As required by §2.1055(a)(1) of CFR 47, frequency tolerance measurements were made over the temperature range of -30EC to +50EC. The frequency measurements were made using direct input to a spectrum analyzer. Climatic control was accomplished using an environmental simulation chamber. The temperature was first lowered to -30EC and then raised hourly in 10E increments. The unit remained in the chamber during temperature transitions and during the measurement process. 6.6.4 Results: Frequency tolerance of carrier signal: +/- 1 KHz for a temperature variation from - 30EC to + 50EC at normal supply voltage. CARRIER FREQUENCY DEVIATIONS DUE TO TEMPERATURE INSTABILITY Temperature Carrier Frequency Deviation Limit (EC) Frequency (1897.55) Deviation (kHz) (MHz) (KHz) * -30 1897.545xx +1 ± 20 * -20 1897.545xx +1 ± 20 -10 1897.54504 0.06 ± 20 0 1897.54503 0.05 ± 20 +10 1897.54498 0 ± 20 +20 1897.54495 -0.03 ± 20 +30 1897.54529 0.31 ± 20 +40 1897.54518 0.20 ± 20 +50 1897.54505 0.07 ± 20 The unit meets the requirements of 2.1055 (a)(1) * Under these temperature ranges, The modulation distortion of the EUT (BS) caused a spreading of the intended signal which was manually/visually determined to deviate no more than 1 KHz. The spreading of the signal did not cause the EUT to generate emissions out of compliance with block edge power requirements of 24.238. Per specification, the operational temperature range is 0 to 45 degree Celsius. EMC1366A - 18 - September 26, 2000

FCC ID:JOYKWB2000 6.7 TEST TYPE: Frequency Stability over Voltage Variations 6.7.1 TECHNICAL SPECIFICATION: 2.1055(d)(1) 6.7.2 TEST DATE(S): 8/17/00 6.7.3 MEASUREMENT PROCEDURES: As required by §2.1055(d)(1) of CFR 47, frequency tolerance measurements were made over changes in the supply voltage to the EUT from 85% to 115% of the nominal supply voltage using a variac to vary the AC supply. The frequency measurements were made using direct input to a spectrum analyzer. 6.7.5 Results: Frequency tolerance of carrier signal: ± 130 Hz for a variation in primary voltage from 85% to 115% of the rated supply. Percentage DC Voltage Carrier Frequency Deviation Deviation Limit of Rated (VDC ) (MHz) (KHz) (kHz) Supply Low end 85 % -40 1897.54505 0.07 ± 20 100 % -48 1897.54498 0 ± 20 115 % -65 1897.54497 -0.01 ± 20 Percentage DC Voltage Carrier Frequency Deviation Deviation Limit of Rated (VDC) (MHz) (Hz) (kHz) Supply High end 85 % -40 1907.44501 0.02 ± 20 100 % -48 1907.44499 0 ± 20 115 % -65 1907.44512 0.13 ± 20 The unit meets the requirements of 2.1055 (d)(1) EMC1366A - 19 - September 26, 2000

FCC ID:JOYKWB2000 6.9 TEST TYPE: Modulation Characteristics 6.9.1 TECHNICAL SPECIFICATION: 2.1047(a) 6.9.2 TEST DATE(S): 8/16/00 6.9.3 MEASUREMENTS REQUIRED: ...” The following plots give a detailed explanation of the modulation scheme used in the PHS-WLL system.

FCC ID:JOYKWB2000


Document Created: 2001-12-21 16:59:57
Document Modified: 2001-12-21 16:59:57
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC