Test Report

FCC ID: JOYKB46

Test Report

Download: PDF
FCCID_4374111

Report on the EMC Testing of: KYOCERA Corporation Mobile Phone, Model: KB46 In accordance with FCC Part 15 Subpart B Class B Prepared for: KYOCERA Corporation Yokohama Office 2—1—1 Kagahara, Tsuzuki—ku, Add value. Yokohama—shi, Kanagawa, 224—8502 Japan Inspiretrust. Phone: +81—45—943—6253 Fax: +81—45—943—6314 COMMERCIAL—IN—CONFIDENCE Document Number: JPD—TR—19142—0 SIGNATURE plrs. ogel JOB TITLE RESPONSIBLE FOR ISSUE DATE Hiroaki Suzuki Deputy Manager of RF Group Approved Signatory 17 JUL 2018 Signatures in this approval box have checked this document in line with the requirements of TUV SUD Japan Ltd. document control rules. EXECUTIVE SUMMARY A sample of this product was tested and found to be compliant with FCC Part 15 Subpart B. (excluding the deviations mentioned in section 1.3 of this document). DISCLAIMER AND COPYRIGHT \‘\“I“"l & & & & ® wWS Ay, The results in this report are applicable only to the equipment tested. ) \\:/_/’ This report shall not be re—produced except in full without the written approval of TUV SUD UIr \\\ — Japan Ltd. 7z z_ y TESTING '/,,,l Ifl\\ C ACCREDIATION 1 ¥ NVLAP LAB CODE 200306—0 M This test report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. TUV SUD Japan Ltd. Phone: +81 (0) 238 28 2881 Yonezawa Testing Center Fax: +81 (0) 238 28 2888 5—4149—7 Hachimanpara, www.tuv—sud.jp Yonezawa—shi, Yamagata, 992—1128 Japan TUV SUD Japan Ltd.

Document Number: JPD—TR—19142—0 Signatures of the individuals responsible for testing the product ENGINEERING STATEMENT The measurements shown in this report were made in accordance with the procedures described on test pages. All reported testing was carried out on a sample equipment to demonstrate limited compliance with FCC Part 15 Subpart B. The sample tested was found to be compliant with the requirements defined in the applied rules. NAME RESPONSIBLE FOR SIGNATURE Nobuhiko Iwasawa Testing % (9&/0% U(j10z2 GOOL Hiroomi Tsuchiya Testing Z%WMV' % A% g ~ e " f@rPertyn i/ TUV SUD Japan Ltd. Nee

Document Number: JPD-TR-19142-0 Contents 1 Summary of Test .................................................................................................................... 4 1.1 Modification history of the test report ........................................................................................ 4 1.2 Standards ................................................................................................................................ 4 1.3 Measurement standards........................................................................................................... 4 1.4 Deviation from standards.......................................................................................................... 4 1.5 List of applied test(s) of the EUT............................................................................................... 4 1.6 Test information ....................................................................................................................... 4 1.7 Test set up ............................................................................................................................... 4 1.8 Test period............................................................................................................................... 4 2 Equipment Under Test ........................................................................................................... 5 2.1 EUT information ....................................................................................................................... 5 2.2 Modification to the EUT ............................................................................................................ 5 2.3 Variation of family model(s) ...................................................................................................... 5 2.4 Operation mode ....................................................................................................................... 6 3 Configuration of Equipment .................................................................................................. 7 3.1 Equipment used ....................................................................................................................... 7 3.2 Cable(s) used .......................................................................................................................... 7 3.3 System configuration................................................................................................................ 8 4 Test Result ............................................................................................................................. 9 4.1 Conducted emission at mains port............................................................................................ 9 4.2 Radiated emission (below 1 GHz) .......................................................................................... 11 4.3 Radiated emission (above 1 GHz) .......................................................................................... 16 5 Measurement Uncertainty.................................................................................................... 22 6 Laboratory Information ........................................................................................................ 23 Appendix A. Test Equipment............................................................................................................... 24 Appendix B. Configuration Photographs ........................................................................................... 25 TÜV SÜD Japan Ltd. Page 3 of 29

Document Number: JPD-TR-19142-0 1 Summary of Test 1.1 Modification history of the test report Document Number Modification History Issue Date JPD-TR-19142-0 First Issue Refer to the cover page 1.2 Standards FCC Part 15 Subpart B 1.3 Measurement standards ANSI C63.4 2014 1.4 Deviation from standards None 1.5 List of applied test(s) of the EUT Regarding judgment of conformance to Emission test, a value of measurement uncertainty was not taken in account. Classification Test Name Test Worst Point (Margin) Result Remark of EUT USB Read/ with PC mode Conducted emission at mains port Class B Applied Pass - L2 0.150 MHz QP 15.5 dB USB Read/ with PC mode Radiated emission (below 1 GHz) Class B Applied Pass - H 161.302 MHz QP 11.1 dB In Camera/ with ADP mode Radiated emission (above 1 GHz) Class B Applied Pass - H 3023.989 MHz QP 11.7 dB 1.6 Test information None 1.7 Test set up Table-top 1.8 Test period 24-May-2019 - 29-May-2019 TÜV SÜD Japan Ltd. Page 4 of 29

Document Number: JPD-TR-19142-0 2 Equipment Under Test 2.1 EUT information Applicant KYOCERA Corporation Yokohama Office 2-1-1 Kagahara, Tsuzuki-ku, Yokohama-shi, Kanagawa, 224-8502 Japan Phone: +81-45-943-6253 Fax: +81-45-943-6314 Equipment Under Test (EUT) Mobile Phone Model number KB46 Serial number 356297100030891 Trade name KYOCERA Authorization JOYKB46 Number of sample(s) 1 EUT condition Pre-production Maximum frequency 2208 MHz Power rating Battery: DC 3.8 V Size (W) 78.2mm × (D) 151.5mm × (H) 17.4mm 2.2 Modification to the EUT The table below details modifications made to the EUT during the test project. Modification State Description of Modification Modification fitted by Date of Modification KB46, S/N: 356297100030891 0 As supplied by the applicant Not Applicable Not Applicable 2.3 Variation of family model(s) 2.3.1 List of family model(s) Not applicable 2.3.2 Reason for selection of EUT Not applicable TÜV SÜD Japan Ltd. Page 5 of 29

Document Number: JPD-TR-19142-0 2.4 Operation mode 1. In Camera/ with ADP mode i) Power ON ii) Record 2. Out Camera/ with ADP mode i) Power ON ii) Record 3. MP4/ with Earphone mode i) Power ON ii) Execution of Color Bar moving picture data 4. USB Read/ with PC mode i) Power ON ii) EUT connects to PC via USB cable iii) Read / write of MP4 moving picture data TÜV SÜD Japan Ltd. Page 6 of 29

Document Number: JPD-TR-19142-0 3 Configuration of Equipment Numbers assigned to equipment or cables in “3.1 Equipment(s) used” and “3.2 Cable(s) used” correspond to numbers in "3.3 System configuration". 3.1 Equipment used FCC ID No. Equipment Company Model No. Serial No. Remarks /DoC EUT1 Mobile Phone KYOCERA KB46 356297100030891 JOYKB46 EUT AE1 AC adapter KDDI 0301PQA HS-TFA N/A *1 AE2 Earphone Hosiden HDH0261 N/A N/A - Personal TYPE 7854- AE3 Lenovo LR-0GDNF DoC - Computer CTO 11S42T4418ZGWG212MKX AE4 AC adapter Lenovo 42T4418 N/A - REV:H *1: AC adapter is connected to keep operating. 3.2 Cable(s) used EUT accessory No. Cable Length (m) Shield Remarks Ferrite core a USB cable 1.0 Yes - - b Earphone cable 1.2 No - - c DC cable for PC AC adapter 1.8 No - - d AC power cord for PC AC adapter 0.8 No - - e USB cable 0.1 Yes - - TÜV SÜD Japan Ltd. Page 7 of 29

Document Number: JPD-TR-19142-0 3.3 System configuration In Camera/ with ADP mode Out Camera/ with ADP mode a AC120V EUT1 AE1 60Hz USB Read/ with PC mode EUT1 a *c # d AC120V AE3 AE4 60Hz * : Bundled excess cable # : Un-detachable cable : Ferrite core MP4/ with Earphone mode e b# EUT1 AE2 # : Un-detachable cable TÜV SÜD Japan Ltd. Page 8 of 29

Document Number: JPD-TR-19142-0 4 Test Result 4.1 Conducted emission at mains port 4.1.1 Measurement condition Frequency range 0.15 MHz-30 MHz Test place 10 m Semi-Anechoic Chamber No. 1 EUT was placed on FRP table (W) 2.0 × (D) 1.0 × (H) 0.8 m Metal reference plane Vertical Test receiver setting Detector: Quasi-peak, Average Bandwidth: 9 kHz Line Impedance Stabilization Specification: 50 Ω/50 μH Network (LISN) Distance from EUT: 0.8 m EUT is placed on a non-conducting table for table-top equipment or on insulation material for a floor- standing equipment. In addition, a table-top equipment is located 0.4 m to a metal reference plane. Line Impedance Stabilization Network (LISN) is placed 0.8 m away from the EUT. The power code of the EUT is connected to LISN and its excess part is bundled in the center. The length of bundling is 0.3-0.4 m. A power code of a peripheral is connected to LISN and terminated into 50 Ω. Excess cables between equipment are bundled in the center. The length of bundling is 0.3-0.4 m. Where LISN cannot be applied, the test is performed using a voltage probe. After overall frequency range is investigated with spectrum analyzer using peak detector, measurements are performed with test receiver in setting to the defined values. 4.1.2 Calculation method Emission level = Reading + c.f. (correction factor)* Margin = Limit – Emission level *Note: c.f. = LISN factor + Cable system loss + Attenuator loss Example) Limit @ 6.770 MHz: 60.0 dBμV (Quasi-peak) 50.0 dBμV (Average) Quasi-peak Reading = 41.2 dBμV c.f. = 10.3 dB Emission level = 41.2 + 10.3 = 51.5 dBμV Margin = 60.0 - 51.5 = 8.5 dB Average Reading = 35.0 dBμV c.f. = 10.3 dB Emission level = 35.0 + 10.3 = 45.3 dBμV Margin = 50.0 - 45.3 = 4.7 dB TÜV SÜD Japan Ltd. Page 9 of 29

Document Number: JPD-TR-19142-0 4.1.3 Test data Operation mode USB Read/ with PC mode EUT KB46, S/N: 356297100030891 - Modification State 0 Date of test: 29-May-2019 Supply voltage: AC 120 V Supply frequency: 60 Hz TÜV SÜD Japan Ltd. Page 10 of 29

Document Number: JPD-TR-19142-0 4.2 Radiated emission (below 1 GHz) 4.2.1 Measurement condition Frequency range 30 MHz-1000 MHz Test place 10 m Semi-Anechoic Chamber No. 1 EUT was placed on Styrene foam table (W) 2.0 × (D) 1.0 × (H) 0.8 m Axis 0°-360° Antenna Distance from EUT: 3 m Height: 1-4 m Polarity: Horizontal/Vertical Test receiver setting Detector: Quasi-peak Bandwidth: 120 kHz EUT is placed on a non-conducting table for table-top equipment or on insulation material for a floor- standing equipment. The non-conducting table or the insulation material is placed on a rotating turn table. Excess cables between equipment are bundled in the center. The length of bundling is 0.3-0.4 m. An antenna is adjusted between 1-4 m in height and varied its polarization (horizontal and vertical), and the EUT azimuth is varied by the rotating turntable 0 to 360 degrees. After overall frequency range is investigated with spectrum analyzer using peak detector, measurements are performed with test receiver in setting to the defined values. 4.2.2 Calculation method Emission level = Reading + c.f. (correction factor)* Margin = Limit - Emission level *Note: c.f. = Antenna factor + Cable system loss + Attenuator loss - Amplifier Gain Example) Limit @ 350.0 MHz: 37.0 dBμV/m Reading = 41.1 dBμV c.f. = -11.8 dB/m Emission level = 41.1 - 11.8 = 29.3 dBμV/m Margin = 37.0 - 29.3 = 7.7 dB TÜV SÜD Japan Ltd. Page 11 of 29

Document Number: JPD-TR-19142-0 4.2.3 Test data Operation mode In Camera/ with ADP mode EUT KB46, S/N: 356297100030891 - Modification State 0 Date of test: 24-May-2019 Supply voltage: AC 120 V Supply frequency: 60 Hz TÜV SÜD Japan Ltd. Page 12 of 29

Document Number: JPD-TR-19142-0 Operation mode Out Camera/ with ADP mode EUT KB46, S/N: 356297100030891 - Modification State 0 Date of test: 24-May-2019 Supply voltage: AC 120 V Supply frequency: 60 Hz TÜV SÜD Japan Ltd. Page 13 of 29

Document Number: JPD-TR-19142-0 Operation mode USB Read/ with PC mode EUT KB46, S/N: 356297100030891 - Modification State 0 Date of test: 24-May-2019 Supply voltage: AC 120 V Supply frequency: 60 Hz TÜV SÜD Japan Ltd. Page 14 of 29

Document Number: JPD-TR-19142-0 Operation mode MP4/ with Earphone mode EUT KB46, S/N: 356297100030891 - Modification State 0 Date of test: 24-May-2019 Supply voltage: DC 3.8 V TÜV SÜD Japan Ltd. Page 15 of 29

Document Number: JPD-TR-19142-0 4.3 Radiated emission (above 1 GHz) 4.3.1 Measurement condition Frequency range 1.0 GHz-7.0 GHz Test place 10 m Semi-Anechoic Chamber No. 1 EUT was placed on Styrene foam table (W) 2.0 × (D) 1.0 × (H) 0.8 m Axis 0°-360° Antenna Distance: 3.98 m, 4.02 m, 3.83 m Height: 1-4 m Polarity: Horizontal/Vertical Test receiver setting Detector: Peak, Average Bandwidth: 1 MHz EUT is placed on a styrene form table for table-top equipment or on insulation material for a floor- standing equipment. The styrene form table or the insulation material is placed on a rotating turn table. Excess cables between equipment are bundled in the center. The length of bundling is 0.3-0.4 m. Absorbers are placed between the EUT and an antenna. The antenna is adjusted between 1-4 m in height and varied its polarization (horizontal and vertical), and the EUT azimuth is varied by the rotating turntable 0 to 360 degrees. Where height of the antenna is changed, its angle is also adjusted to the position of the EUT. After overall frequency range is investigated with spectrum analyzer using peak detector, measurements are performed with test receiver in setting to the defined values. The antenna is positioned from the test volume that was predetermined by the site VSWR measurement. Since this predetermined test volume is different from maximum circumference where the EUT and the peripheral devices are actually placed, the measurement distance conversion factor is added to the measurement data. Antenna 3 dB beamwidth (antenna used: 3117) Antenna: 3115 Frequency (GHz) θ3 dB (°) 3 dB beamwidth w (m) 1.0 63 3.68 2.0 47 2.61 3.0 38 2.07 4.0 36 1.95 5.0 40 2.18 6.0 44 2.42 Antenna: 3117 Frequency (GHz) θ3 dB (°) 3 dB beamwidth w (m) 1.0 82 5.22 2.0 60 3.46 3.0 76 4.69 4.0 56 3.19 5.0 54 3.06 6.0 50 2.80 Measurement distance: d = 3.0 m W = 2 × d × tan (0.5 × θ3 dB) TÜV SÜD Japan Ltd. Page 16 of 29

Document Number: JPD-TR-19142-0 4.3.2 Calculation method Emission level = Reading + Measurement distance conversion factor + c.f. (correction factor)* Margin = Limit - Emission level *Note: c.f. = Antenna factor + Cable system loss + Attenuator loss - Amplifier Gain Example) Limit @ 1100.0 MHz: 70.0 dBμV/m (Peak) 50.0 dBμV/m (Average) Measurement distance: 3.25 m Measurement distance conversion factor: 20 log (3.25m/3.0m) = 0.7 dB Peak Reading = 50.2 dBμV, Measurement distance conversion factor = 0.7 dB, c.f. = 1.7 dB/m Emission level = 50.2 + 0.7 + 1.7 = 52.6 dBμV/m Margin = 70.0 – 52.6 = 17.4 dB Average Reading = 32.0 dBμV, Measurement distance conversion factor = 0.7 dB, c.f. = 1.7 dB/m Emission level = 32.0 + 0.7 + 1.7 = 34.4 dBμV/m Margin = 50.0 – 34.4 = 15.6 dB TÜV SÜD Japan Ltd. Page 17 of 29

Document Number: JPD-TR-19142-0 4.3.3 Test data Operation mode In Camera/ with ADP mode EUT KB46, S/N: 356297100030891 - Modification State 0 Date of test: 29-May-2019 Supply voltage: AC 120 V Supply frequency: 60 Hz TÜV SÜD Japan Ltd. Page 18 of 29

Document Number: JPD-TR-19142-0 Operation mode Out Camera/ with ADP mode EUT KB46, S/N: 356297100030891 - Modification State 0 Date of test: 29-May-2019 Supply voltage: AC 120 V Supply frequency: 60 Hz TÜV SÜD Japan Ltd. Page 19 of 29

Document Number: JPD-TR-19142-0 Operation mode USB Read/ with PC mode EUT KB46, S/N: 356297100030891 - Modification State 0 Date of test: 29-May-2019 Supply voltage: AC 120 V Supply frequency: 60 Hz TÜV SÜD Japan Ltd. Page 20 of 29

Document Number: JPD-TR-19142-0 Operation mode MP4/ with Earphone mode EUT KB46, S/N: 356297100030891 - Modification State 0 Date of test: 29-May-2019 Supply voltage: DC 3.8 V TÜV SÜD Japan Ltd. Page 21 of 29

Document Number: JPD-TR-19142-0 5 Measurement Uncertainty The reported measurement uncertainty is based on a value obtained by multiplying standard uncertainty by coverage factor of k=2, and a level of confidence becomes 95 %. Item Parameter Ulab Ucispr Conducted Emission, AMN 9kHz to 150kHz ± 3.8 dB ± 3.8 dB Conducted Emission, AMN 150kHz to 30MHz ± 3.3 dB ± 3.4 dB Conducted Emission, Voltage Probe 9kHz to 30MHz ± 2.8 dB ± 2.9 dB Conducted Emission, AAN 150kHz to 30MHz ± 4.9 dB ± 5.0 dB Conducted Emission, Current Probe 150kHz to 30MHz ± 2.9 dB ± 2.9 dB Disturbance Power 30MHz to 300MHz ± 4.2 dB ± 4.5 dB Radiated Emission 30MHz to 1000MHz ± 4.9 dB ± 6.3 dB Radiated Emission 1GHz to 6GHz ± 4.8 dB ± 5.2 dB Radiated Emission 6GHz to 18GHz ± 5.1 dB ± 5.5 dB Radiated Emission 9kHz to 30MHz ± 3.1 dB - TÜV SÜD Japan Ltd. Page 22 of 29

Document Number: JPD-TR-19142-0 6 Laboratory Information Testing was performed and the report was issued at: TÜV SÜD Japan Ltd. Yonezawa Testing Center Address: 5-4149-7 Hachimanpara, Yonezawa-shi, Yamagata, 992-1128 Japan Phone: +81-238-28-2881 Fax: +81-238-28-2888 Accreditation and Registration NVLAP LAB CODE: 200306-0 VLAC Accreditation No.: VLAC-013 BSMI Laboratory Code: SL2-IN-E-6018, SL2-A1-E-6018 Innovation, Science and Economic Development Canada Site number Facility Expiration date 4224A-4 3 m Semi-anechoic chamber 27-November-2020 4224A-5 10 m Semi-anechoic chamber No. 1 27-November-2020 4224A-6 10 m Semi-anechoic chamber No. 2 14-December-2019 VCCI Council Registration number Expiration date A-0166 03-July-2021 TÜV SÜD Japan Ltd. Page 23 of 29

Document Number: JPD-TR-19142-0 Appendix A. Test Equipment Conducted emission at mains port Equipment Company Model No. Serial No. Cal. due Cal. Date EMI receiver ROHDE&SCHWARZ ESR7 101742 31-Jan-2020 25-Jan-2019 Line impedance Kyoritsu Technology stabilization TNW-407F2 12-17-110-2 31-May-2020 16-May-2019 Corporation network for EUT Attenuator HUBER+SUHNER 6810.01.A N/A(S442) 31-Dec-2019 17-Dec-2018 Coaxial cable FUJIKURA 5D-2W/4m N/A(S349) 31-Oct-2019 10-Oct-2018 Microwave cable HUBER+SUHNER SUCOFLEX104/2m 317672/4 31-Oct-2019 10-Oct-2018 Coaxial cable HUBER+SUHNER RG214/U/25m N/A(S191) 31-Oct-2019 12-Oct-2018 PC HP dc7800small JPA7450FPJ N/A N/A Software TOYO Corporation EP5/CE-AJ 0611193/V5.4.11 N/A N/A Radiated emission (below 1 GHz) Equipment Company Model No. Serial No. Cal. due Cal. date EMI receiver ROHDE&SCHWARZ ESR7 101742 31-Jan-2020 25-Jan-2019 Biconical antenna Schwarzbeck VHA9103/BBA9106 VHA91032850 31-Oct-2019 17-Oct-2018 Log periodic Schwarzbeck UHALP9108A 0992 31-Jul-2019 23-Jul-2018 antenna Attenuator TDC TAT-43B-06 N/A(S209) 31-Jul-2019 11-Jul-2018 Attenuator TAMAGAWA.ELEC CFA-01NPJ-3 N/A(S270) 31-May-2020 17-May-2019 Microwave cable HUBER+SUHNER SUCOFLEX104/9m MY23758/4 31-Oct-2019 10-Oct-2018 Microwave cable HUBER+SUHNER SUCOFLEX104/1m MY24628/4 31-Oct-2019 10-Oct-2018 Microwave cable HUBER+SUHNER SUCOFLEX104/2m SN MY28398/4 31-Oct-2019 10-Oct-2018 Microwave cable HUBER+SUHNER SUCOFLEX106/13m MY1159/6 31-Oct-2019 12-Oct-2018 Preamplifier ANRITSU MH648A M96057 31-Jan-2020 17-Jan-2019 10m Semi-anechoic TOKIN N/A N/A(9001-NSA3m) 31-Oct-2019 12-Oct-2018 Chamber PC HP dc7800small JPA7450FPJ N/A N/A Software TOYO Corporation EP5/RE-AJ 0611193/V5.6.0 N/A N/A Radiated emission (above 1 GHz) Equipment Company Model No. Serial No. Cal. due Cal. date EMI receiver ROHDE&SCHWARZ ESR7 101742 31-Jan-2020 25-Jan-2019 Preamplifier TSJ MLA-0118-J02-40 14882 31-Oct-2019 10-Oct-2018 Double ridged guide ETS LINDGREN 3117 00209352 30-Nov-2019 06-Nov-2018 antenna Attenuator Agilent Technologies 8491B MY39268632 31-May-2020 17-May-2019 Microwave cable HUBER+SUHNER SUCOFLEX104/9m 800693/4 31-May-2019 18-May-2018 Microwave cable HUBER+SUHNER SUCOFLEX104/1.5m SN MY19304/4 31-Oct-2019 10-Oct-2018 Microwave cable HUBER+SUHNER SUCOFLEX104/2m SN MY28398/4 31-Oct-2019 10-Oct-2018 Microwave cable HUBER+SUHNER SUCOFLEX106/13m MY1159/6 31-Oct-2019 12-Oct-2018 Absorber RIKEN PFP30 N/A N/A N/A 10m Semi-anechoic TOKIN N/A N/A(9001-SVSWR) 31-Oct-2019 13-Oct-2018 Chamber PC HP dc7800small JPA7450FPJ N/A N/A Software TOYO Corporation EP5/RE-AJ 0611193/V5.6.0 N/A N/A TÜV SÜD Japan Ltd. Page 24 of 29

Document Number: JPD-TR-19142-0 Appendix B. Configuration Photographs Conducted emission at mains port Conducted emission at mains port USB Read/ with PC mode The photographs show maximized emission configuration. Radiated emission (below 1 GHz) Radiated emission (below 1 GHz) In Camera/ with ADP mode The photographs show maximized emission configuration. TÜV SÜD Japan Ltd. Page 25 of 29

Document Number: JPD-TR-19142-0 Radiated emission (below 1 GHz) Radiated emission (below 1 GHz) Out Camera/ with ADP mode The photographs show maximized emission configuration. Radiated emission (below 1 GHz) Radiated emission (below 1 GHz) USB Read/ with PC mode The photographs show maximized emission configuration. TÜV SÜD Japan Ltd. Page 26 of 29

Document Number: JPD-TR-19142-0 Radiated emission (below 1 GHz) Radiated emission (below 1 GHz) MP4/ with Earphone mode The photographs show maximized emission configuration. Radiated emission (above 1 GHz) Radiated emission (above 1 GHz) In Camera/ with ADP mode The photographs show maximized emission configuration. TÜV SÜD Japan Ltd. Page 27 of 29

Document Number: JPD-TR-19142-0 Radiated emission (above 1 GHz) Radiated emission (above 1 GHz) Out Camera/ with ADP mode The photographs show maximized emission configuration. Radiated emission (above 1 GHz) Radiated emission (above 1 GHz) USB Read/ with PC mode The photographs show maximized emission configuration. TÜV SÜD Japan Ltd. Page 28 of 29

Document Number: JPD-TR-19142-0 Radiated emission (above 1 GHz) Radiated emission (above 1 GHz) MP4/ with Earphone mode The photographs show maximized emission configuration. TÜV SÜD Japan Ltd. Page 29 of 29


Document Created: 2019-07-17 14:43:18
Document Modified: 2019-07-17 14:43:18
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC