KA73_SAR Test Report_5_rev

FCC ID: JOYKA73

RF Exposure Info

Download: PDF
FCCID_2882236

Page 87 of 95 Calibration ‘ Laboratory of SAz g Schweizerischer Kalibrierdienst Schm!d & Partner ;B\Efi{/fi c Service suisse d‘étalonnage Engineering AG o Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland *41/’?\\\“\3 S swiss Calibration Service thil lt Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Client VITEC Certificate No: D2450V2—765_Oct15 CALIBRATION CERTIFICATE Object D2450V2 — SN: 765 Calibration procedure(s) QA CAL—05.v9 Calibration procedure for dipole validation kits above 700 MHz Calibration date: October 21, 2015 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter EPM—442A GB37480704 07—Oct—15 (No. 217—02222) Oct—16 Power sensor HP 8481A US37202783 07—Oct—15 (No. 217—02222) Oct—16 Power sensor HP 8481A MY41092317 07—Oct—15 (No. 217—02223) Oct—16 Reference 20 dB Attenuator SN: 5058 (20k) 01—Apr—15 (No. 217—02131) Mar—16 Type—N mismatch combination SN: 5047.2 / 06327 O1—Apr—15 (No. 217—02134) Mar—16 Reference Probe EX3DV4 SN: 7349 30—Dec—14 (No. EX3—7349_Dec14) Dec—15 DAE4 SN: 601 17—Aug—15 (No. DAE4—601_Aug15) Aug—16 Secondary Standards ID # Check Date (in house) Scheduled Check RF generator R&S SMT—06 100972 15—Jun—15 (in house check Jun—15) In house check: Jun—18 Network Analyzer HP 8753E US37390585 $4206 18—Oct—01 (in house check Oct—15) In house check: Oct—16 <)to Name Function Signature Calibrated by: Leif Klysner Laboratory Technician Approved by: Katia Pokovic Technical Manager eAE Issued: October22, 2015 This calibration certificate shall not be reproduced exceptin full without written approvalof the laboratory. Certificate No: D2450V2—765_Oct15 Page 1 of 8 Report number: 2101C—15138 TUV SUD Zacta Ltd FCC ID: JOYKA73 Test Report Rev SAR—FCC1.0

Page 88 of 95 & z lm Cahbra“on Laboratorv of S\\\\\\\'_////,/’;_ g Schweizerischer Kalibrierdienst SChmI.d & Partner i&—/m c Service suisse d‘étalonnage Englneerlng AG pve Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland {'/,,/7/-?\@? S swiss Calibration Service Alulals Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented paralle! to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. e SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D2450V2—765_Oct15 Page 2 of 8 Report number: 2101C—15138 TUV SUD Zacta Ltd FCC ID: JOYKA73 Test Report Rev SAR—FCC1.0

Page 89 of 95 Measurement Conditions DASY system contfiguration, as far as not given onpage 1. DASY Version DASY5 V52.8.8 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2450 MHz & 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 38.0 + 6 % 1.84 mho/m + 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 13.4 W/kg SAR for nominal Head TSL parameters normalized to 1W 52.7 Wikg * 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 6.16 Wikg SAR for nominal Head TSL parameters normalized to 1W 24.4 Wikg x 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.7 1.95 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 52.8 16 % 1.99 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 13.1 Wi/kg SAR for nominal Body TSL parameters normalized to 1W 51.9 Wikg + 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 250 mW input power 6.10 W/kg SAR for nominal Body TSL parameters normalized to 1W 24.3 Wikg # 16.5 %(k=2) Certificate No: D2450V2—765_Oct15 Page 3 of 8 TUV SUD Zacta Ltd Report number: Z101C—15138 Test Report Rev SAR—FCC1.0 FCC ID: JOYKA73

Page 90 of 95 Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 54.2 Q + 5.1 jQ Return Loss —23.9 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 50.1 Q + 6.6 jQ Return Loss —23.6 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.155 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on August 10, 2004 Certificate No: D2450V2—765_Oct15 Page 4 of 8 Report number: 2101C—15138 TUV SUD Zacta Ltd FCC ID: JOYKA73 Test Report Rev SAR—FCC1.0

Page 91 of 95 DASY5 Validation Report for Head TSL Date: 21.10.2015 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz ; Type: D2450V2; Serial: D2450V2 — SN: 765 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 1.84 S/m; & = 38; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvF(7.67, 7.67, 7.67); Calibrated: 30.12.2014; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn601; Calibrated: 17.08.2015 * Phantom: Flat Phantom 5.0 (front); Type: QDOOOP50AA; Serial: 1001 e DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm,/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 114.5 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 27.9 W/kg SAR(I g) = 13.4 W/kg; SAR(10 g) = 6.16 W/ikg Maximum value of SAR (measured) = 22.0 W/kg ~4.60 —8.20 —13.00 —18.40 —23.00 0 dB = 22.0 W/kg = 13.42 dBW/kg Certificate No: D2450V2—765_Oct15 Page 5 of 8 TUV SUD Zacta Ltd Report number: Z101C—15138 Test Report Rev SAR—FCC1.0 FCC ID: JOYKA73

Page 92 of 95 Zacta Impedance Measurement Plot for Head TSL 21 Oct 2015 ag:40:30 CHZ sai 4 uors 11 54.242 a 51094 0 334.91 pH 2 450.000 00a MHz . * Del Ca fAive 16 H1d CH2 Del Ca By 16° H1d START 2 250.000 000 MHz STOP 2 650.000 000 Certificate No: D2450V2—765_Oct15 Page 6 of 8 TUV SUD Zacta Ltd Report number: Z101C—15138 Test Report Rev SAR—FCC1.0 FCC ID: JOYKA73

Page 93 of 95 DASY5 Validation Report for Body TSL Date: 21.10.2015 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz ; Type: D2450V2; Serial: D2450V2 — SN: 765 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 1.99 S/m; &, = 52.8; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI C€63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN7349; ConvF(7.53, 7.53, 7.53); Calibrated: 30.12.2014; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAF4 $Sn601; Calibrated: 17.08.2015 e Phantom: Flat Phantom 5.0 (back); Type: QDOOOP50AA; Serial: 1002 e DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 108.6 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 26.0 W/kg SAR(I g) = 13.1 W/kg; SAR(10 g) = 6.1 W/ikg Maximum value of SAR (measured) = 21.4 W/kg —8.00 13.20 —17.60 —22.00 0 dB = 21.4 W/kg = 13.30 dBW/kg Certificate No: D2450V2—765_Oct15 Page 7 of 8 TUV SUD Zacta Ltd Report number: Z101C—15138 Test Report Rev SAR—FCC1.0 FCC ID: JOYKA73

Page 94 of 95 Impedance Measurement Plot for Body TSL 21 Oct 2015 ©9:39:53 CHI) sii 1 U FS 1: 50.080 a 6.6406 2 434.38 pH 2 450.000 000 MHz Del Ca Av 1.&'»a H1d CH2 Del Ca Av 1.6s H1d START 2 250.000 0ad MHz STOP 2 650.000 000 MHz Certificate No: D2450V2—765_Oct15 Page 8 of 8 Report number: 2101C—15138 TUV SUD Zacta Ltd FCC ID: JOYKA73 Test Report Rev SAR—FCC1.0

Page 95 of 95 Attachment 3. SAR system validation SAR System Validation Per FCC KDB 865664 DO2v01r02, SAR system validation status should be documented to confirm measurement accuracy. The SAR systems (including SAR probes, system components and software versions) used for this device were validated against its performance specifications prior to the SAR measurements. Reference dipoles were used with the required tissue— equivalent media for system validation, according to the procedures outlined in IEEE 1528— 2013 and FCC KDB 865664 DO1v01r04. Since SAR probe calibrations are frequency dependent, each probe calibration point was validated at a frequency within the valid frequency range of the probe calibration point, using the system that normally operates with the probe for routine SAR measurements and according to the required tissue—equivalent media. A tabulated summary of the system validation status including the validation date(s), measurement frequencies, SAR probes and tissue dielectric parameters has been included. Table Attachment 3.1 SAR System Validation Summary PERM. COND. CW Validation MOD. Validation SAR Freq. Probe Probe CAL. — Data . Sensi— Probe Probe MOD. Duty System [MHz] Type Point (er) (0) W L PAR tivity Linearity Isotropy Type Factor E 835 20154122 3745 835 Head 40820 0.891 PASS PASS PASS GMSK PASS NA E 1900 2015123 3745 1900 Head 40.040 1419 PASS PASS PASS GMSK PASS NA E 2450 2015121 3745 2450 Head 38.220 1.845 PASS PASS PASS OFDM| NA PASS E 835 20154122 3745 835 Body 54230 0.997 PASS PASS PASS GMSK PASS NA E 1900 2015133 3745 1900 Body 52420 1.556 PASS PASS PASS GMSK PASS NA E 2450 20151241 3745 2450 Body 51.160 1.970 PASS PASS PASS OFDM| NA PASS TUV SUD Zacta Ltd Report number: 21010—15138 Test Report Rev.SARFCC1.0 FCC ID: JOYKA73


Document Created: 2019-09-19 05:59:28
Document Modified: 2019-09-19 05:59:28
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC