Test Report (JBP) rev 2.pdf

FCC ID: JNZS00169

Test Report

Download: PDF
FCCID_3680816

FCC Test Report Report No.: FC171122E03 Test Model: S-00169 Received Date: Nov. 22, 2017 Test Date: Nov. 24 to 28, 2017 Issued Date: Dec. 07, 2017 Applicant: LOGITECH FAR EAST LTD. Address: #2 Creation Rd. 4, Science-Based Ind. Park Hsinchu Taiwan, R.O.C. Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan R.O.C. Test Location (1): E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan R.O.C. Test Location (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. FCC Registration / 810758 / TW1085 for Test Location (1) Designation Number: 960022 / TW1058 for Test Location (2) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification.. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: FC171122E03 Page No. 1 / 26 Report Format Version: 6.1.2

Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ......................................................................................................................... 4 2 Summary of Test Results......................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information ................................................................................................................................. 6 3.1 Features of EUT .................................................................................................................................. 6 3.2 General Description of EUT ................................................................................................................ 6 3.3 Operating Modes of EUT and Determination of Worst Case Operating Mode ................................... 7 3.4 Test Program Used and Operation Descriptions ................................................................................. 7 3.5 Primary Clock Frequencies of Internal Source ................................................................................... 7 3.6 Miscellaneous ...................................................................................................................................... 8 4 Configuration and Connections with EUT ............................................................................................. 9 4.1 Connection Diagram of EUT and Peripheral Devices ......................................................................... 9 4.2 Configuration of Peripheral Devices and Cable Connections ........................................................... 10 5 Conducted Emissions at Mains Ports ................................................................................................... 11 5.1 Limits .................................................................................................................................................. 11 5.2 Test Instruments ................................................................................................................................. 11 5.3 Test Arrangement .............................................................................................................................. 12 5.4 Supplementary Information ............................................................................................................... 12 5.5 Test Results ....................................................................................................................................... 13 6 Radiated Emissions up to 1 GHz .......................................................................................................... 15 6.1 Limits ................................................................................................................................................. 15 6.2 Test Instruments ................................................................................................................................ 16 6.3 Test Arrangement .............................................................................................................................. 17 6.4 Supplementary Information ............................................................................................................... 17 6.5 Test Results ....................................................................................................................................... 18 7 Radiated Emissions above 1 GHz......................................................................................................... 20 7.1 Limits ................................................................................................................................................. 20 7.2 Test Instruments ................................................................................................................................ 21 7.3 Test Arrangement .............................................................................................................................. 22 7.4 Supplementary Information ............................................................................................................... 22 7.5 Test Results ....................................................................................................................................... 23 8 Pictures of Test Arrangements ............................................................................................................. 25 Appendix – Information on the Testing Laboratories ................................................................................ 26 Report No.: FC171122E03 Page No. 2 / 26 Report Format Version: 6.1.2

Release Control Record Issue No. Description Date Issued FC171122E03 Original release. Dec. 07, 2017 Report No.: FC171122E03 Page No. 3 / 26 Report Format Version: 6.1.2

1 Certificate of Conformity Product: Gaming Speakers Brand: Logitech Test Model: S-00169 Sample Status: ENGINEERING SAMPLE Applicant: LOGITECH FAR EAST LTD. Test Date: Nov. 24 to 28, 2017 Standards: 47 CFR FCC Part 15, Subpart B, Class B ICES-003:2016 Issue 6, Class B ANSI C63.4:2014 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : , Date: Dec. 07, 2017 Wendy Wu / Specialist Approved by : , Date: Dec. 07, 2017 Ken Lu / Manager Report No.: FC171122E03 Page No. 4 / 26 Report Format Version: 6.1.2

IEEoGEnt MBolrs 2 Summary of Test Results 47 CFR FCC Part 15, Subpart B , Class B/ ICES—003:2016 Issue 6, Class ANSI ©€63.4:2014 FCC ICES—003 . Clause Clause Test Item Result/Remarks Verdict AC Power Line Conducted Minimum passing Class B margin 15.107 61 __|emissions is —3.70 dB at 0.398438 MHz Pass 6.21 Radiated Emissions up to 1 |Minimum passing Class B margin Pass C GHz is —3.76 dB at 196.65 MHz 15.109 — —— — — — 6.2.2 Radiated Emissions above 1 Minimum passing Class B margin Pass C GHz is —26.10 dB at 2604.25 MHz Note: There is no deviation to the applied test methods and requirements covered by the scope of this report. 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT: The listed uncertainties are the worst case uncertainty for the entire range of measurement. Please note that the uncertainty values are provided for informational purposes only and are not used in determining the PASS/FAIL results. Measurement Frequency EXpanifigzfijT&ertainty Conducted Emissions at mains ports 150kHz ~ 30MHz 1.84 dB Radiated Emissions up to 1 GHz 30MHz ~ 1GHz 3.91 dB 1GHz ~6GHz 4.73 dB Radiated Emissions above 1 GHz 6GHz ~18GHz 5.24 dB 18GHz ~40GHz 5.25 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: FC171122E03 Page No. 5 / 26 Report Format Version: 6.1.2

3 General Information 3.1 Features of EUT The tests reported herein were performed according to the method specified by LOGITECH FAR EAST LTD., for detailed feature description, please refer to the manufacturer's specifications or user's manual. 3.2 General Description of EUT Product Gaming Speakers Brand Logitech Test Model S-00169 Status of EUT ENGINEERING SAMPLE Power Supply Rating 100-240Vac, 50/60Hz Antenna Type Refer to Note Antenna Connector Refer to Note Accessory Device USB to Micro USB cable (shielded, 2.55m) x 1 Data Cable Supplied NA Note: 1. The EUT may have a lot of colors for marketing requirement. 2. The EUT must be supplied with a internal power supply as following table: Brand Model No. Spec. Input: 100-240Vac, 50/60Hz, 2.5A NA S104AF24004002 Output: 24 / 5Vdc, 4 / 1.5A AC output cable: 2.2m, unshielded 3. The antenna provided to the EUT, please refer to the following table: Antenna Gain Frequency Connecter Brand Model Antenna Type (dBi) range(GHz) Type Walsin Technology RFFPA380640IMAB301 2.73 2.4-2.4835 PCB Antenna i-pex Corporation 4. The above EUT information is declared by manufacturer and for more detailed features description, please refers to the manufacturer's specifications or User's Manual. Report No.: FC171122E03 Page No. 6 / 26 Report Format Version: 6.1.2

3.3 Operating Modes of EUT and Determination of Worst Case Operating Mode The EUT is designed with AC power of rating 100-240Vac, 50/60Hz. For radiated emission test, the EUT has been pre-tested under following test modes, and test modes C was the worst case for final test. Test Condition Mode Radiated emission test Input Output A BT IN Spearker B AUX IN Spearker C USB In Spearker D USB In Earphone Test modes are presented in the report as below. Test Condition Mode Conducted emission / Radiated emission test Input Output 1 USB In Spearker 3.4 Test Program Used and Operation Descriptions 1. Turn on the power of all equipment. 2. Support unit A (Laptop) runs "media player.exe" program to plays music to EUT. 3. Support unit A (Laptop) runs” EMC test.exe” then sends "H" messages to itself. 3.5 Primary Clock Frequencies of Internal Source The EUT is Bluetooth device, provided by LOGITECH FAR EAST LTD., for detailed internal source, please refer to the manufacturer's specifications. Report No.: FC171122E03 Page No. 7 / 26 Report Format Version: 6.1.2

3.6 Miscellaneous Labelling Requirements for Part 15 Devices:  Verification The specific labelling requirements for a device subject to the Verification procedure are contained in Section 15.19(a). These labelling requirements are: If the device is subject only to Verification, include a label bearing a unique identifier (Section 2.954) and one of three compliance statements specified in Section 15.19(a). If the labeling area for the device is so small, and/or it is not practical to place the compliance statement on the device, then the statement can be placed in the user manual or product packaging (Section 15.19(a)(5)). However, the device must still be labelled with the unique identifier (Verification). Generally, devices smaller than the palm of the hand are considered too small for the compliance statement.  Certification If the device is subject to Certification: (1) Section 2.925 contains information on identification of the equipment; (2) include a label bearing an FCC Identifier (FCC ID) (Section 2.926) and (3) include the appropriate compliance statement in Section 15.19(a). If the device is considered too small and therefore it is impractical (smaller than the palm of the hand) to display the compliance statement, then the statement may be placed in the user manual or product packaging. However, the device must still be labelled with the FCC ID. If the device is unquestionably too small for the FCC ID to be readable (smaller than 4-6 points), the FCC ID may be placed in the user manual. However, it must be determined that the device itself is too small – the label area allocated to the FCC ID may not be reduced because of over crowded identification of other product and regulatory information. An electronic display of the FCC ID (see 9. Electronic Labelling below) may be used for Certification of Section 15.212 modular transmitters and software defined radios (Section 2.944).  Declaration of Conformity (DoC): The labelling requirements for a device subject to the DoC procedure are specified in Section 15.19(b). The label should include the FCC logo along with the Trade Name and Model Number, which satisfies the unique identifier requirement of Section 2.1074 if it represents the identical equipment tested for DoC compliance. For personal computers assembled from authorized components, the following additional text must also be included: “Assembled from tested components,” “Complete system not tested.” When the device is so small and/or when it is not practical to place the required additional text on the device, the text may be placed in the user manual or pamphlet supplied to the user. However, the FCC logo, Trade Name, and Model Number must still be displayed on the device (Section 15.19(b)(3)). Part 15 Declaration of Conformity (DoC) Label Examples Equipment certified as software defined radio may use a means that readily displays the FCC ID on an electronic display screen, instead of labelling the device (Section 2.925 (e)). Further information may refer to FCC KDB:784748 D01 Labelling Part 15 &18 Guidelines Labelling Requirements for ICES-003 Devices:  Industry Canada ICES-003 Compliance Label: CAN ICES-3 (*)/NMB-3(*) * Insert either “A” or “B” but not both to identify the applicable Class of ITE. Report No.: FC171122E03 Page No. 8 / 26 Report Format Version: 6.1.2

4 Configuration and Connections with EUT 4.1 Connection Diagram of EUT and Peripheral Devices For Conducted / Radiated Tests (1) Headphone Jack EUT AUX USB in (2) (3) (B)USB Mouse (A)Laptop (4) (C)Printer Report No.: FC171122E03 Page No. 9 / 26 Report Format Version: 6.1.2

COoeco vERITAS 4.2 Contiguration of Peripheral Devices and Cable Connections ID Product Brand Model No. Serial No. ECC ID Remarks A Laptop DELL E5440 BDC7F12 FGC DoG Provided by Lab B USB Mouse DELL MOSEUO 349003988 NA Provided by Lab C Printer EPSON LQ—300+I1 GS8YO74086 FGC DoG Provided by Lab 1. All power cords of the above support units are non—shielded (1.8m). ID Descriptions Qty. Length (m) Shielding (Yes/No) Gores (Qty.) Remarks 1 AC Power Cable 1 2.2 No 0 Supplied by client 2 USB to Micro USB Cable 1 2.55 Yes 0 Supplied by client 3 USB Cable 1 1.8 Yes 0 Provided by Lab 4 USB Cable 1 1.8 Yes 0 Provided by Lab Report No.: FC171122E03 Page No. 10 / 26 Report Format Version: 6.1.2

5 Conducted Emissions at Mains Ports 5.1 Limits Class A (dBuV) Class B (dBuV) Frequency (MHz) Quasi-peak Average Quasi-peak Average 0.15 - 0.5 79 66 66 - 56 56 - 46 0.50 - 5.0 73 60 56 46 5.0 - 30.0 73 60 60 50 Notes: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases linearly with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 5.2 Test Instruments DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL Test Receiver ESCS 30 100375 May. 09, 2017 May. 08, 2018 R&S Line-Impedance Stabilization Network NSLK-8127 8127-522 Aug. 31, 2017 Aug. 30, 2018 (for EUT) SCHWARZBECK Line-Impedance Stabilization Network ENV216 100072 June 03, 2017 June 02, 2018 (for Peripheral) R&S RF Cable 5D-FB COACAB-002 Mar. 03, 2017 Mar. 02, 2018 10 dB PAD HAT-10+ CONATT-003 Sep. 11, 2017 Sep. 10, 2018 Mini-Circuits 50 ohms Terminator N/A EMC-03 Sep. 22, 2017 Sep. 21, 2018 50 ohms Terminator N/A EMC-02 Sep. 22, 2017 Sep. 21, 2018 Software BVADT_Cond_ NA NA NA BVADT V7.3.7.4 Note: 1. The calibration interval of the above test instruments are 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in Conducted Room C 3 The VCCI Con C Registration No. is C-3611. 4 Tested Date: Nov. 24, 2017 Report No.: FC171122E03 Page No. 11 / 26 Report Format Version: 6.1.2

5.3 Test Arrangement a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The test results of conducted emissions at mains ports are recorded of six worst margins for quasi-peak (mandatory) [and average (if necessary)] values against the limits at frequencies of interest unless the margin is 20 dB or greater. Note: The resolution bandwidth and video bandwidth of test receiver is 9kHz for quasi-peak detection (QP) and average detection (AV) at frequency 0.15MHz-30MHz. For the actual test configuration, please refer to the related Item – Photographs of the Test Configuration. 5.4 Supplementary Information There is not any deviation from the test standards for the test method. Report No.: FC171122E03 Page No. 12 / 26 Report Format Version: 6.1.2

IEEoGEnt MBolrs 5.5 Test Results Detector Function Quasi—Peak (QP)/ Frequency Range 150kHz ~ 30MHz & Resolution Bandwidth Average (AV), IkHz Environmental o 0 Input Power 120Vac, 60Hz Conditions 25°C, 71%RH Tested by David Chuang Test Mode Mode 1 Phase Of Power : Line (L) Frequency |Correction| Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.16172 10.12 31.03 19.23 41.15 29.35 65.38 55.38 —24.23 —26.03 2 0.38438 10.15 33.30 32.98 43.45 43418 58.18 4818 —14.73 —5.05 3 0.53281 10.16 32.30 25.94 42.46 3610 56.00 46.00 —13.54 —9.90 4 1.15234 10.19 20.33 20.26 30.52 30.45 56.00 46.00 —25.48 —15.55 5 1.91797 10.24 17.50 16.80 27.74 27.04 56.00 46.00 —28.26 —18.9% 6 8.88672 10.45 18.34 12.64 28.79 23.09 60.00 50.00 —31.21 —26.91 Remarks: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value PK Trace [.~~ 100 — ar Limit _ Can Lirnit n o.is 1.00 10.00 so.00 Nki Report No.: FC171122E03 Page No. 13 / 26 Report Format Version: 6.1.2

IEEoGEnt MBolrs Detector Function Quasi—Peak (QP) / Frequency Range 150kHz ~ 30MHz & Resolution Average (AV), IkHz Bandwidth Input Power 120Vac, 60Hz (E:';‘:;fii"o";zma' 25°C, 71%RH Tested by David Chuang Test Mode Mode 1 Phase Of Power : Neutral (N) Frequency |Correction| Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.15391 10.13 32.42 21.06 42.55 31.19 65.79 55.79 —23.24 —24.60 2 0.38438 10.17 34.67 34.31 44.84 44.48 58.18 48.18 —13.34 —3.70 3 0.54063 10.17 32.50 26.91 42.67 37.08 56.00 46.00 —13.33 —8.92 4 0.76719 10.18 21.99 17.46 32.17 27.64 56.00 46.00 —23.83 —18.36 5 9.15625 10.49 18.72 12.86 29.21 23.35 60.00 50.00 —30.79 —26.65 6 24.00000 10.90 20.64 17.88 31.54 28.78 60.00 50.00 —28.46 —21.22 Remarks: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value PIi Trace _ aP Limit .~— Ga Limnit ~ + i 10.00 20 .00 hivis Report No.: FC171122E03 Page No. 14 / 26 Report Format Version: 6.1.2

6 Radiated Emissions up to 1 GHz 6.1 Limits Emissions radiated outside of the specified bands, shall be according to the general radiated limits as following: Radiated Emissions Limits at 10 meters (dBμV/m) Frequencies FCC 15B / ICES-003, FCC 15B / ICES-003, CISPR 22, Class A CISPR 22, Class B (MHz) Class A Class B 30-88 39 29.5 88-216 43.5 33.1 40 30 216-230 46.4 35.6 230-960 47 37 960-1000 49.5 43.5 Radiated Emissions Limits at 3 meters (dBμV/m) Frequencies FCC 15B / ICES-003, FCC 15B / ICES-003, CISPR 22, Class A CISPR 22, Class B (MHz) Class A Class B 30-88 49.5 40 88-216 54 43.5 50.5 40.5 216-230 56.9 46 230-960 57.5 47.5 960-1000 60 54 Notes: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. QP detector shall be applied if not specified. Report No.: FC171122E03 Page No. 15 / 26 Report Format Version: 6.1.2

6.2 Test Instruments DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL Test Receiver N9038A MY50010125 Apr. 15, 2017 Apr. 14, 2018 Agilent N9038A MY50010132 June 16, 2017 June 15, 2018 Pre-Amplifier 310N 352925 Aug. 28, 2017 Aug. 27, 2018 Sonoma 310N 352926 Aug. 28, 2017 Aug. 27, 2018 Trilog Broadband VULB 9168 9168-359 Dec. 28, 2016 Dec. 27, 2017 Antenna VULB 9168 9168-358 Dec. 16, 2016 Dec. 15, 2017 SCHWARZBECK Fixed attenuator UNAT-5+ CHF-001 Sep. 07, 2017 Sep. 06, 2018 Mini-Circuits UNAT-5+ CHF-002 Sep. 07, 2017 Sep. 06, 2018 CHFCAB-001-1 CHFCAB-001-3 Sep. 20, 2017 Sep. 19, 2018 CHFCAB-001-4 RF Cable 8D-FB CHFCAB-002-1 CHFCAB-002-3 Sep. 20, 2017 Sep. 19, 2018 CHFCAB-002-4 Software ADT_Radiated_V NA NA NA BVADT 8.7.08 Antenna Tower & Turn Table NA NA NA NA CT Note: 1. The calibration interval of the above test instruments are 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in Chamber F room 3. The VCCI Site Registration No. is R-3252. 4. The CANADA Site Registration No. is IC 7450H-1. 5. Tested Date: Nov. 28, 2017 Report No.: FC171122E03 Page No. 16 / 26 Report Format Version: 6.1.2

6.3 Test Arrangement a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at an accredited test facility. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 10 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is up to 1 GHz. Note: The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for quasi-peak detection (QP) at frequency up to 1GHz. 10 m For the actual test configuration, please refer to the related Item – Photographs of the Test Configuration. 6.4 Supplementary Information There is not any deviation from the test standards for the test method. Report No.: FC171122E03 Page No. 17 / 26 Report Format Version: 6.1.2

IEEoGEnt MBolrs 6.5 Test Results Detector Function & Frequency Range 30MHz ~ 1GHz Resolution Quasi—Peak (QP), 120kHz Bandwidth Input Power 120Vac, 60Hz Egfi'&%?oflgmal 23°C , 69%RH Tested by David Chuang Test Mode Mode 1 Antenna Polarity & Test Distance : Horizontal at 10 m Emission hss . Antenna Table Raw Correction No Fr?&tg;cy Level ( dIB_:JT/I/tm) l\/izg)ln Height Angle Value Factor (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 7210 26.17 QP 30.00 —3.83 4.00 H 34 41.69 —15.52 2 131.10 24.79 QP 30.00 —5.21 4.00 H 213 38.73 —13.94 3 179.74 24.79 QP 30.00 —5.21 4.00 H 79 38.85 —14.06 4 196.65 26.24 QP 30.00 —3.76 4.00 H 69 41.70 —15.46 5 288.00 32.69 QP 37.00 —4.31 3.00 H 338 44.59 —11.90 6 489.88 29.14 QP 37.00 —7.86 2.00 H 58 35.81 —6.67 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) — Pre—Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level — Limit value Level (dBuVim) 80— 70 80 50 a0 an—— 4 20 10 0 10— , i i i i i i i i 1 30 100 200 300 400 510 600 700 800 900 1000 Frequency (MHz) Report No.: FC171122E03 Page No. 18 / 26 Report Format Version: 6.1.2

IEEoGEnt MBolrs Detector Function & Frequency Range 3OMHz ~ 1GHz Resolution Quasi—Peak (QP), 120kHz Bandwidth Input Power 120Vac, 60Hz gg‘r’]'é‘ii?oflgma' 23°C, 69%RH Tested by David Chuang Test Mode Mode 1 Antenna Polarity & Test Distance : Vertical at 10 m Emission hss . Antenna Table Raw Correction No Fr((a'\c;ll.'l_'ir;cy Level ( dIB_:JT/I/tm) l\/izg)ln Height Angle Value Factor (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 83.67 24.04 QP 30.00 —5.96 2.00 V 261 42.32 —18.28 2 124.36 23.71 QP 30.00 —6.29 2.00 V 78 37.86 —14.15 3 130.01 25.22 QP 30.00 —4.78 1.00 V 146 38.93 —13.71 4 163.86 23.11 QP 30.00 —6.89 1.00 V 160 35.71 —12.60 5 192.01 23.55 QP 30.00 —6.45 1.00 V 276 39.07 —15.52 6 432.02 33.14 QP 37.00 —3.86 1.00 V 168 40.58 —7 44 Remarks: 1. Emission Level(dBuV/m)= Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) — Pre—Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level — Limit value Level (dBuVim} 50— 70 50 50 80 En ; 33 20 10 0 10— i 1 i i i i i 1 i 1 31 100 200 300 400 510 600 700 500 900 1000 Frequency (MHz) Report No.: FC171122E03 Page No. 19 / 26 Report Format Version: 6.1.2

7 Radiated Emissions above 1 GHz 7.1 Limits Emissions radiated outside of the specified bands, shall be according to the general radiated limits as following: Radiated Emissions Limits at 10 meters (dBμV/m) Frequencies FCC 15B / ICES-003, FCC 15B / ICES-003, CISPR 22, Class A CISPR 22, Class B (MHz) Class A Class B 1000-3000 Avg: 49.5 Avg: 43.5 Not defined Not defined Above 3000 Peak: 69.5 Peak: 63.5 Not defined Not defined Radiated Emissions Limits at 3 meters (dBμV/m) Frequencies FCC 15B / ICES-003, FCC 15B / ICES-003, CISPR 22, Class A CISPR 22, Class B (MHz) Class A Class B Avg: 56 Avg: 50 1000-3000 Avg: 60 Avg: 54 Peak: 76 Peak: 70 Peak: 80 Peak: 74 Avg: 60 Avg: 54 Above 3000 Peak: 80 Peak: 74 Notes: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Frequency Range (For unintentional radiators) Highest frequency generated or used in the device or Upper frequency of measurement range (MHz) on which the device operates or tunes (MHz) Below 1.705 30 1.705-108 1000 108-500 2000 500-1000 5000 5th harmonic of the highest frequency or 40GHz, Above 1000 whichever is lower Report No.: FC171122E03 Page No. 20 / 26 Report Format Version: 6.1.2

7.2 Test Instruments DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL Test Receiver N9038A MY50010125 Apr. 15, 2017 Apr. 14, 2018 Agilent Pre-Amplifier 8449B 3008A01975 Feb. 26, 2017 Feb. 25, 2018 Agilent Horn Antenna BBHA 9120D D123 Dec. 15, 2016 Dec. 14, 2017 SCHWARZBECK EMC104-SM-SM RF Coaxial Cable 170209 Mar. 07, 2017 Mar. 06, 2018 -11000 EMC104-SM-SM RF Coaxial Cable 170207 Mar. 07, 2017 Mar. 06, 2018 -6000 EMC104-SM-SM RF Coaxial Cable 170206 Mar. 07, 2017 Mar. 06, 2018 -2500 Software ADT_Radiated_ NA NA NA BVADT V8.7.08 Antenna Tower & Turn Table NA NA NA NA CT Fix tool for Boresight BAF-01 5 NA NA antenna tower Note: 1. The calibration interval of the above test instruments are 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in Chamber F room 3. Tested Date: Nov. 24, 2017 Report No.: FC171122E03 Page No. 21 / 26 Report Format Version: 6.1.2

7.3 Test Arrangement a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at an accredited chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna can be varied from one meter to four meters, the height of adjustment depends on the EUT height and the antenna 3dB beamwidth both, to detect the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The spectrum analyzer system was set to peak and average detect function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. Note: The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth is 3MHz for Peak detection (PK) at frequency above 1GHz. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz for Average detection (AV) at frequency above 1GHz. < Frequency Range above 1GHz > Ant. Tower 1 - 4m Variable EUT& 3m Support Units Turn Table Absorber 80cm Ground Plane Test Receiver The test arrangement is in accordance with ANSI 63.4:2014. For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. 7.4 Supplementary Information There is not any deviation from the test standards for the test method. Report No.: FC171122E03 Page No. 22 / 26 Report Format Version: 6.1.2

IEEoGEnt MBolrs 7.5 Test Results Detecto_r Function & Peak (PK) / Frequency Range 1GHz ~12.5GHz Szfigwltgt):: Average (AV), 1MHz Input Power 120Vac, 60Hz gg‘r’]'é‘ii?oflgma' 23°C, 73%RH Tested by Kevin Ko Test Mode Mode 1 Antenna Polarity & Test Distance : Horizontal at 3 m Emission hss . Antenna Table Raw Correction No Fr?&tg;cy Level ( dIB_:JT/I/tm) l\/izg)ln Height Angle Value Factor (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1071.00 40.75 PK 74.00 —33.25 1.00 H 44 46.99 —6.24 2 1071.00 23.68 AV 54.00 —30.32 1.00 H 44 29.92 —6.24 3 1397.50 41.89 PK 74.00 —32.11 1.00 H 245 45.99 —4.10 4 1397.50 24.89 AV 54.00 —29.11 1.00 H 245 28.99 —4.10 5 1646.37 41.38 PK 74.00 —32.62 1.00 H 22 44.24 —2.86 6 1646.37 25.06 AV 54.00 —28.94 1.00 H 22 27.92 —2.86 7 1993.37 40.80 PK 74.00 —33.20 1.00 H 259 42.08 —1.28 8 1993.37 25.48 AV 54.00 —28.52 1.00 H 259 26.76 —1.28 9 2590.00 39.92 PK 74.00 —34.08 1.00 H 42 39.26 0.66 10 2590.00 27.74 AV 54.00 —26.26 1.00 H 42 27.08 0.66 11 3197.62 42.70 PK 74.00 —31.30 1.00 H 305 39.97 2.73 12 3197.62 27.81 AV 54.00 —26.19 1.00 H 305 25.08 2.73 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) — Pre—Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level — Limit value Level (dBuVim} 90 80 70 60 50 40 30 20 10 0 1 1 1 1 1 i i i i 1 1000 2000 4000 6000 8000 10000 12000 14000 16000 18000 Frequency (MHz) Report No.: FC171122E03 Page No. 23 / 26 Report Format Version: 6.1.2

IEEoGEnt MBolrs Detecto_r Function & Peak (PK) / Frequency Range 1GHz ~12.5GHz Szfigwltgt);: Average (AV), 1MHz Input Power 120Vac, 60Hz gg‘r’]'é‘ii?oflgma' 23°C, 73%RH Tested by Kevin Ko Test Mode Mode 1 Antenna Polarity & Test Distance : Vertical at 3 m Emission hss . Antenna Table Raw Correction No Fr((a'\c;ll.'l_'ir;cy Level ( dIB_:JT/I/tm) l\/izg)ln Height Angle Value Factor (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1040.12 41.29 PK 74.00 —32.71 1.00 V 144 47.72 —6.43 2 1040.12 25.71 AV 54.00 —28.29 1.00 V 144 32.14 —6.43 3 1399.37 45.99 PK 74.00 —28.01 1.00 V 219 50.09 —4.10 4 1399.37 25.93 AV 54.00 —28.07 1.00 V 219 30.03 —4.10 5 1602.00 43.40 PK 74.00 —30.60 1.00 V 261 46.43 —3.03 6 1602.00 24.77 AV 54.00 —29.23 1.00 V 261 27.80 —3.03 7 2246.50 41.67 PK 74.00 —32.33 1.00 V 148 40.52 115 8 2246.50 27.11 AV 54.00 —26.89 1.00 V 148 25.96 115 9 2604.25 41.66 PK 74.00 —32.34 1.00 V 131 27.34 14.32 10 2604.25 27.90 AV 54.00 —26.10 1.00 V 131 13.58 14.32 11 3188.87 46.35 PK 74.00 —27.65 1.00 V 137 43.62 2.73 12 3188.87 27.75 AV 54.00 —26.25 1.00 V 137 25.02 2.73 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) — Pre—Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level — Limit value Level (dBuVim) s0 80 o En s0 40 30 20 10 0 1 i i i i i i i i i 1000 2000 4000 €000 €000 10000 12000 14000 16000 18000 Frequency (MHz) Report No.: FC171122E03 Page No. 24 / 26 Report Format Version: 6.1.2

8 Pictures of Test Arrangements Please refer to the attached file (Test Setup Photo). Report No.: FC171122E03 Page No. 25 / 26 Report Format Version: 6.1.2

Appendix – Information on the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are FCC recognized accredited test firms and accredited according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-6668565 Fax: 886-2-26051924 Fax: 886-3-6668323 Hwa Ya EMC/RF/Safety Lab Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: FC171122E03 Page No. 26 / 26 Report Format Version: 6.1.2


Document Created: 2017-12-15 13:23:39
Document Modified: 2017-12-15 13:23:39
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC