Test Report

FCC ID: JLFPTE1

Test Report

Download: PDF
FCCID_872078

Date: August 22, 2007 Federal Communications Commission Via: Electronic Filing Attention: Authorization & Evaluation Division Applicant: International Electronics Inc. Equipment: Push to Exit FCC ID: JLFPTE1 FCC Rules: 15.249 Gentlemen: On behalf of the Applicant, enclosed please find Application Form 731, Engineering Test Report and all pertinent documentation, the whole for approval of the referenced equipment as shown. We trust the same is in order. Should you need any further information, kindly contact the writer who is authorized to act as agent. Sincerely yours, Hoosamuddin S. Bandukwala, Lab Director enclosure(s) cc: Applicant HSB/mdw Flom Test Labs 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax

List Of Exhibits (FCC Certification (Transmitters) - Revised 9/28/98) Applicant: International Electronics Inc. FCC ID: JLFPTE1 By Applicant: 1. Letter Of Authorization 2. Identification Drawings Id Label Location Info Attestation Statement(s) Location of Compliance Statement 3. Documentation: 2.1033(B) (3) User Manual(s) (4) Operational Description (5) Block Diagram (5) Schematic Diagram (7) External Photographs Internal Photographs Parts List Active Devices By F.T.L. Inc. A. Testimonial & Statement of Certification B. Statement of Qualifications Flom Test Labs 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax

Transmitter Certification of FCC ID: JLFPTE1 Model: Push to Exit to Federal Communications Commission Rule Part(s) 15.249 Date Of Report: August 22, 2007 Date of Revised Report: November 15, 2007 On the Behalf of the Applicant: International Electronics Inc. 5913-C NE 127th Ave, Suite 800 Vancouver, WA 98682 Attention of: Shary Nassimi, President (360) 241-9090 email: iei@nwlink.com Supervised By: Hoosamuddin S. Bandukwala, Lab Director Flom Test Labs 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax

The applicant has been cautioned as to the following: 15.21 Information to User. The users manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.27(a) Special Accessories. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer, without additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. Flom Test Labs 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax

Testimonial And Statement Of Certification This is to certify that: 1. That the application was prepared either by, or under the direct supervision of, the undersigned. 2. That the technical data supplied with the application was taken under my direction and supervision. 3. That the data was obtained on representative units, randomly selected. 4. That, to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct. Certifying Engineer: Hoosamuddin S. Bandukwala, Lab Director Flom Test Labs 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax

Table Of Contents Rule Description Page Test Report 1 2.1033(c) General Information Required 2 . Standard Test Conditions and Engineering Practices 4 Test Results Summary 5 15.249. Field Strength of Fundamental 6 15.249(d) Field Strength of Harmonics 6 15.249(c), Radiated Spurious Emissions 8 . Test Equipment Utilized 11 Flom Test Labs 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax

Required information per ISO 17025-2005, paragraph 5.10: a) Test Report b) Laboratory: Flom Test Lab, Inc. (FCC: 31040/SIT) 3356 N. San Marcos Place, Suite 107 (Canada: IC 2044) Chandler, AZ 85225 c) Report Number: d0780025 d) Client: International Electronics Inc. e) Identification: Push to Exit Description: Transmitter f) EUT Condition: Not required unless specified in individual tests. g) Report Date: August 22, 2007 EUT Received: h, j, k): As indicated in individual tests. i) Sampling method: No sampling procedure used. l) Uncertainty: In accordance with FTL internal quality manual. m) Supervised by: Hoosamuddin S. Bandukwala, Lab Director n) Results: The results presented in this report relate only to the item tested. o) Reproduction: This report must not be reproduced, except in full, without written permission from this laboratory. Flom Test Labs 3356 N. San Marcos Place, Suite 107 Page 1 of 11 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax

List Of General Information Required For Certification In Accordance with FCC Rules and Regulations, Volume II, Part 2 and to 15.249 Sub-Part 2.1033 (c)(1): Name and Address of Applicant: International Electronics Inc. (c)(2): FCC ID: JLFPTE1 Model Number: Push to Exit (c)(3): Instruction Manual(s): Please See Attached Exhibits (c)(4): Type of Emission: N/A (c)(5): FREQUENCY RANGE, MHz: 902 to 928 (c)(6): Power Rating, dBuV/m: 93.3 Switchable Variable X Low Power (c)(7): Maximum Power Rating, dBuV/m: 93.97 15.203: Antenna Requirement: X The antenna is permanently attached to the EUT The antenna uses a unique coupling The EUT must be professionally installed The antenna requirement does not apply The unit was tested with a quarter wave stub antenna with a gain of 3.0 dBi. Flom Test Labs 3356 N. San Marcos Place, Suite 107 Page 2 of 11 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax

Subpart 2.1033 (continued) (c)(8): Circuit Diagram/Circuit Description: Including description of circuitry & devices provided for determining and stabilizing frequency, for suppression of spurious radiation, for limiting modulation and limiting power. Please See Attached Exhibits (c)(9): Label Information: Please See Attached Exhibits (c)(10): Photographs: Please See Attached Exhibits (c)(11): Digital Modulation Description: ___ Attached Exhibits _x_ N/A (c)(12): Test And Measurement Data : Follows Flom Test Labs 3356 N. San Marcos Place, Suite 107 Page 3 of 11 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax

Sub-part 2.1033(b): Test And Measurement Data All tests and measurement data shown were performed in accordance with FCC Rules and Regulations, Volume II; Part 2 and the following individual Parts: 15.249 Operation within bands 902 - 928 MHz Standard Test Conditions and Engineering Practices Except as noted herein, the following conditions and procedures were observed during the testing: In accordance with ANSI C63.4-2004, and unless otherwise indicated in the specific measurement results, the ambient temperature of the actual EUT was maintained within the range of 10° to 40°C (50° to 104 °F) unless the particular equipment requirements specify testing over a different temperature range. Also, unless otherwise indicated, the humidity levels were in the range of 10% to 90% relative humidity. Prior to testing, the EUT was tuned up in accordance with the manufacturer's alignment procedures. All external gain controls were maintained at the position of maximum and/or optimum gain throughout the testing. Measurement results, unless otherwise noted, are worst-case measurements. A2LA “A2LA has accredited Flom Test Labs, Inc. Chandler, AZ for technical competence in the field of Electrical testing. The accreditation covers the specific tests and types of tests listed on the agreed scope of accreditation. This laboratory meets the requirements of ISO 17025:2005 ‘General Requirements for the Competence of Testing and Calibration Laboratories’ and any additional program requirements in the identified field of testing.” Please refer to www.a2la.org for current scope of accreditation. Certificate number: 2152.01 IC O.A.T.S. Number: 2044A-1 Flom Test Labs 3356 N. San Marcos Place, Suite 107 Page 4 of 11 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax

Test Results Summary Specification Test Name Pass, Fail, Comments N/A 15.249(a) Field Strength of Fundamental Pass 15.249(a) Field Strength of Harmonics Pass 15.249 Radiated Spurious Emissions Pass Flom Test Labs 3356 N. San Marcos Place, Suite 107 Page 5 of 11 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax

Name of Test: Field Strength of Fundamental Specification: 15.249(a) Test Equipment Utilized i00228, i00317 Test Procedure 15.249(a) The field strength of emissions from intentional radiators operating in the 903 – 928 band shall comply with the following: Fundamental frequency, MHz Field strength of fundamental, Field strength of harmonics, mV / meter uV /meter 902 - 928 50 500 1mV = 1000uV 50000uV/mtr converts to 93.97 dBuV/mtr (20X log(E)) 500uV/mtr converts to 74.0 dBuV/mtr (Peak) 54.0 dBuV/mtr (Avg) The UUT was tested on an Open Area Test Site (OATS) set 3 meters from the receiving antenna. A spectrum analyzer was used to verify the UUT met the requirements for Radiated Spurious Emissions. The UUT was tested with the appropriate antenna in both the vertical and horizontal orientation and raised from 1 to 4 meters while rotating the UUT 360° to ensure the TX signal levels were maximized. Test Setup Spectrum UUT Analyzer Field Strength of Fundamental table Tuned Emission Recorded Correction Corrected Specification Result Frequency Frequency Measurement, factor, dB Measurement, Limit, dBuV/m MHz MHz dBuV/m dBuV/m 903.000000 903.131000 63.6 28.5 92.1 93.97 Pass 915.000000 915.695000 64.0 29.3 93.3 93.97 Pass 926.000000 926.750000 61.0 29.7 90.7 93.97 Pass Flom Test Labs 3356 N. San Marcos Place, Suite 107 Page 6 of 11 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax

Name of Test: Field Strength of Harmonics Specification: 15.249 Spec. Limit: Test Equipment Utilized i00029, i00329 Test Procedure The UUT was tested on an Open Area Test Site (OATS) set 3 meters from the receiving antenna. A spectrum analyzer was used to verify the UUT met the requirements for Radiated Spurious Emissions. The UUT was tested with the appropriate antenna in both the vertical and horizontal orientation and raised from 1 to 4 meters while rotating the UUT 360° to ensure the TX signal levels were maximized . Only the worst case is recorded in the Field Strength of Harmonics table. Test Setup UUT Antenna Spectrum Analyzer Field Strength of Harmonics Table 903MHz Tuned Emission Recorded Corrected Corrected Specification Result Frequency Frequency Measurement, level, dB Measurement, Limit, dBuV/m MHz MHz dBuV/m dBuV/m Peak 903.000000 1806.360000 4.1 34.2 38.3 74.0 Pass 903.000000 2710.330000 0.1 38.7 38.8 74.0 Pass 903.000000 3612.542000 -0.6 42.6 42.0 74.0 Pass 903.000000 4515.014000 -1.6 37.6 36.0 74.0 Pass 903.000000 5419.580000 -0.5 40.3 39.8 74.0 Pass 903.000000 6321.326000 4.3 41.4 45.7 74.0 Pass 915MHz Tuned Emission Recorded Corrected Corrected Specification Result Frequency Frequency Measurement, level, dB Measurement, Limit, dBuV/m MHz MHz dBuV/m dBuV/m Peak 915.000000 1831.470000 4.5 30.9 35.4 74.0 Pass 915.000000 2746.962000 -0.2 34.5 34.3 74.0 Pass 915.000000 3662.592000 -0.4 36.4 36.0 74.0 Pass 915.000000 4578.168000 -0.1 37.8 37.7 74.0 Pass 915.000000 5493.774000 -0.1 40.4 40.3 74.0 Pass 915.000000 6409.444000 4.7 41.6 46.3 74.0 Pass 927MHz Tuned Emission Recorded Corrected Corrected Specification Result Frequency Frequency Measurement, level, dB Measurement, Limit, dBuV/m MHz MHz dBuV/m dBuV/m Peak 927.000000 1853.572000 7.1 31.0 38.1 74.0 Pass 927.000000 2780.132000 -1.6 34.7 33.1 74.0 Pass 927.000000 3706.854000 -0.9 36.5 35.6 74.0 Pass 927.000000 4633.396000 0.2 38.0 38.2 74.0 Pass 927.000000 5560.030000 0.5 40.5 41.0 74.0 Pass 927.000000 6486.904000 5.0 41.7 46.7 74.0 Pass th th The EUT was tested out to the 10 harmonic. There were no observable spurious emissions past the 6 harmonic. The measurements all were below the 54dBuV (average) value as a peak value. Flom Test Labs 3356 N. San Marcos Place, Suite 107 Page 7 of 11 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax

Name of Test: Radiated Spurious Emissions Specification: 15.249(c), 15.209(a), 15.205 Spec. Limit: Test Equipment Utilized i00029, i00033, i00088, i00089, i00103 Test Procedure The UUT was tested on an Open Area Test Site (OATS) set 3 meters from the receiving antenna. A spectrum analyzer was used to verify the UUT met the requirements for Radiated Spurious Emissions. The UUT was tested with the appropriate antenna in both the vertical and horizontal orientation and raised from 1 to 4 meters while rotating the UUT 360° to ensure the TX signal levels were maximized. Test Setup UUT Antenna Spectrum Analyzer Settings RBW = 100 KHz VBW = 100KHz Detector – Quasi Peak Sample Calculations Corrected Level = Recorded Level + Correction factor Correction factor = ACF + Cable loss + Distance Correction factor Distance Correction factor = 10 log D1/D2 Radiated Spurious Emissi ons Tuned Freq Emission Freq Monitored Level Correction Factor Corrected Value Limit Result (MHz) (MHz) (dBuV/m) (dB) (dBuV/m) (dBuV/m) 915.000000 34.232230 18.2 13.6 31.8 40.0 Pass 915.000000 178.514740 16.5 15.7 32.2 40.0 Pass 915.000000 350.104000 16.1 17.8 33.9 46.0 Pass 915.000000 581.911470 16.2 22.8 39.0 46.0 Pass 915.000000 649.782800 17.0 23.6 40.6 46.0 Pass 915.000000 819.800000 16.1 25.5 41.6 46.0 Pass Flom Test Labs 3356 N. San Marcos Place, Suite 107 Page 8 of 11 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax

Band Edge Plots This picture contains a plot of the hi frequency modulated carrier with a marker on the peak. Then a marker delta was set and dialed out to the band edge (green tag on the graph) The resultant delta is the difference from the ambient noise floor to the peak signal (for this graph 50.84 db below the carrier peak) Flom Test Labs 3356 N. San Marcos Place, Suite 107 Page 9 of 11 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax

Band Edge Plots (cont) This picture contains a plot of the hi frequency modulated carrier with a marker on the peak. Then a marker delta was set and dialed out to the band edge (green tag on the graph) The resultant delta is the difference from the ambient noise floor to the peak signal (for this graph 50.16 db below the carrier peak) Flom Test Labs 3356 N. San Marcos Place, Suite 107 Page 10 of 11 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax

Test Equipment Utilized Description MFG Model Number FTL Asset Number Last Cal Date Cal Due Date Bi-conical Antenna EMCO 3109B i00088 10/14/05 10/14/07 Log Periodic Antenna Aprel 2001 i00089 10/20/05 10/20/07 Horn Antenna EMCO 3115 i00103 9/5/06 9/5/07 Spectrum Analyzer HP 8566B i00329 4/16/07 4/16/08 In addition to the above listed equipment standard RF connectors and cables were utilized in the testing of the described equipment. Prior to testing these components were tested to verify proper operation. END OF TEST REPORT Flom Test Labs 3356 N. San Marcos Place, Suite 107 Page 11 of 11 Chandler, Arizona 85225-7176 p0690002, d0780025 (866) 311-3268 phone, (480) 926-3598 fax


Document Created: 2007-11-21 10:06:45
Document Modified: 2007-11-21 10:06:45
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC