12

FCC ID: JLFM1

Operational Description

Download: PDF
FCCID_63264

Full—featured MMMATOBHED Vehicle Security System e Longer Range Receiver Design. * Advanced Tolerant Every Transistor Is Protected. FCCID RECEIVER: JLFMI e Valet Mode Via Remote.. As well as using the Valet Button. TRANSMITTER: JLFTX4 * Dome Light Supervision Circuitry. FCC Notice: * Accepts 4 Button and 2 Button Remotes... Simultancously! This device complies with FCC * Automatically conforms to different remote configurations. Part 15 regulations. This device * Permanent Chirp Delete Function Via Remote. 1: Will not cause harmful * Separate Driver / All Doors Unlocks, interference with other devices. * Permanent Warn Delete Via Remote. 2: Must accept interference, «Ignition Controlled Door locks; Selectable. including that which may cause eBuilt—in 2 zone Shock Sensor. undesired operation. «"Anti Hijack Via Remote" Feature. «Code Learning Feature, up to 4 Remotes. «Built—in Lights Relay, 12 Amp. «Parking Lights Supervision Output; Selectable. eMulti — Car Operation. «Fuzzy Logic Shock Sensor. eAdvanced "Shock Learn" function. «Horn Honk Output. »Smart Passive Locking Feature. The system will never lock your keys in the car, but knows when your keys are NOT in the car! e«MemoMax*" Feature Remembers All Settings and States Of The System. On Power—up, the system initiates in the last state it was before last power—down! BE CAREFUL NOT TO USE YOUR TEST LIGHT ON THE AIRBAG WIRES, AS THAT COULD DEPLOY YOUR AIR BAG. KEEP YOUR HEAD AND BODY AWAY FROM THE STEERING WHEEL WHEN TESTING WIRES UNDER DASH. IMPORTANT TEACH THE REMOTES FIRST. CODE LEARNING FEATURE (OR TO ADD A NEW TRANSMITTER): 1— Turn the ignition to the "On" position. 2— Press and hold the VALET button until the system "Chirps" to indicate ready to learn status. 3— Press Button#1 of the new transmitter once. The system will "Chirp" to indicated learned remote. (If you teach Button #2 instead, then that remote will control this vehicle from its button #2, and treat button#1 as the second button. This feature is designed for 2 car operation}. 4— Another remote may be taught now. S— When done, turn off the ignition. The system will chirp to indicate done. Note: If you place the system in learn mode and teach nothing, the system will exit in 10 seconds. Note: If the 4 location limit is exceeded, the system erases old codes. To erase a lost remote, teach remaining or new remotes a total of 4 times.

oyARMING AND DISARMING THESYSTEM: NOTE: In VALET mode, there are no Chirps issued. in VALET mode, the lights only flash once. NOTE: if the CHIRPS have been deleted previously. arming and disarming issue no chirps. 2 Button Remote..... Button #1 = Arm, 1 Chirp, 1 Flash, Button #1= Oisarm, 2 Chirps, 2 Fiashes. 4 Button Remote..... Button#1 = Arm, 1 Chirp, 1 Flash. Button#2 = Disarm, 2 Chirps, 2 Flashes. REMOTEDOORLOCKS If this OPTIONALFEATURE is installed, The Doors Will Lock And Unlock as the system is Armed and Disarmed. CONTROLLINGTHEDRIVER‘S DOOR LOCKSSEPARATELY_ _ Dip Switch #5 ON If this OPTIONAL FEATURE is installed, the system can Unlock the Driver‘s Door separately from the other doors. 2 Button Remote: Unlocking / Disarming using Button #1 (When system is armed or doors are locked) will Only Uniock The Driver‘s Door. Pressing Button #2 one time unlocks all doors. 4 Button Remote: When system is armed, press the Unlock Button once. Only the Driver‘s Door will unlock. Pressing the Unlock Button a second time unlocks all doors. On disarm, if the alarm soundedin your absence. the zone memory will issue a report.. . The following codes will be issued: 3 Chirps: External Shock Sensor Triggered. 4 chirps: Door Intrusion. 5 Chirps: Extemal Sensor (Such as Radar) triggered. 6 Chirps: Shock Sensor (Internal) triggered. PANIC VIA REMOTE;:. 2 Button Remote..... Hold button #1 down for 3 seconds; The alarm will sound. Works regardiess of alarm status. Press Button#1 again to stop the sound. 4 Button Remote..... Press and hold the 3rd button marked with a "Hom". The alarm will sound. Press the DISARM button to stop the sound. CHANNEL #2 OR TRUNK RELEASE (Optional.. extra installation may be required) 2 Button Remote..... Press and hold button #2 until the trunk opens (3 seconds). 4 Button Remote..... Press and hold the UNLOCK button until the trunk opens. If the alarm is armed, the system will automatically disarm and unlock the doors. There is no need to disarm the system before you open the trunk via remote. IGNITION TRIGGERED DOOR LOCKS:(If selected) § Seconds after the engine has been started by your key, the system will lock the doors to protect the occupants. The doors will unlock when the ignition has been tumed off. THIS FEATURE IS CANCELED AUTOMATICALLY if the door is open or opened during the 5 seconds noted above, protecting against accidentallocking of the keys in the car. SMART FLASHING LED; The LED informs you of the status of the system: — Stow flash = Armed. «Very Fast flash = Passive arming is counting down. — Solid on = The system is in valet mode. — Fast flash = Alarm Sounded in your absence. PERMANENT_CHIRP DELETE / RESTORE; To mute the chirps issued during Arm, Disarm and Successful Remote Engine Start cycles...Using the remote: 1— Tum the ignition Switch to the "ON" position. 2— Press Button #2 4 times in a row. 3— The system will indicate CHIRP delete or restore by issuing the 1o|lowing "Chirps": 2 "Chirps" = System will "Chirp" during arm / disarm. 3 "Chirps" = Chirps have been deleted. NOTE: The chirps are temporarily reinstated when the system faggles WARN & CHIRP mades, as well as during Shack and Code Leam procedures. WARN—FIRSY FEATURE: This system features a special shock sensor design which will wam the would be intruder to stay away, using a short "Burst" of wamning alarm "Chirps". The setting of this feature is always set to 50% of your shock sensor setting . HOWEVER, IF THE SHOCK SETTING IS ADJUSTED TO SENSITIVE, THE WARN FEATURE IS AUTOMATICALLY DEACTIVATED BY THE COMPUTER avoiding annoying wamings. TODEACTIVATEWARN—FIRST FEATURE; Press Button #2 4 times . The system will chirp to indicate the status of the Wam—Away feature; 2 Chirp = Wam—First is ENABLED. 3 Chirps = Wam—away is DISABLED. The setting will not change, EVEN WITHOUT POWER CONNECTED, until you change it again.

International Electronics, Inc. Exhibit B FCC ID JLFM1 "MINI Receiver" Technical Information. This device is designed to function as a vehicle security system. The device is comprised of: : Integrated Super Regenerative Receiver _A 2: Impact Sensor to detect intrusion into the vehicle. 3: I/O connectors for interface to vehicle. 4: Code memory to store ID of unit. 5: Microcontroller with built in program memory. 6: Power supply circuit, comprising of a simple 100ma regulator. 7: Case to protect device. 8: Relays to control output functions. Wire Antenna 1/4 wave or 3/4 wave Litcrecontralier 0h Sm and memeory 1 evion Impast Sensor

twice to indicate the cycle has begun. The 60 second timer is reset each time a protected opening has been opened. The LED fashes rapidly at this time. The doors will not lock when armed passively, unless the installer has set the option to allow for the doors to lock automatically. DOOR INPUTS ARE DELAYED; This system features DELAYED door inputs ( 1 second) when opened with the alarm armed. This feature is designed to avoid the computer glitches generated by some cars a few minutes after the last door has been closed, avoiding fafse afarms without any loss of security. CODE LEARNING FEATURE (OR TOADD A NEW TRANSMITTER): To "Teach: new or additional remates to this system.. 1— Turn the ignition to the "On" position. 2— Press and hold the VALET button until the system "Chirps" to indicate ready to learn status. 3— Press Button#1 of the new transmitter once. The system will "Chirp" to indicated learned remote. {if you teach Button #2 instead, then that remote will control this vehicle from its button #2, and treat button#1 as the second button, This feature is designed for 2 car operation). 4— Another remote may be taught now. 5— When done, tum off the ignition. The system will chirp to indicate done. Note: If you place the system in learn mode and teach nothing, the system will exit in 10 seconds. Note: If the 4 location limit is exceeded, the system erases old codes. To erase a lost remote, teach remaining or new remotes a total of 4 times. The memory for the codes is NON VOLATILE and will not be erased by power failure for 10 years or more. (c) 1999, International Electronics, Inc. All rights reserved. IEl is not responsible for defective installation. MADENUA


Document Created: 2001-05-23 10:50:43
Document Modified: 2001-05-23 10:50:43
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC