User Manual

FCC ID: JLFCWPIR

Users Manual

Download: PDF
FCCID_1124843

® Model CWPIR Wireless Motion Alert Sensor Overview Step 2 The Wireless Alert Sensor is a Passive Infra-Red (PIR) sensor that detects movement of people and vehicles, while allowing small animals to pass through undetected. Each sensor has its own unique ID, for a secure radio link. The base station (not provided) can learn the signals of up to 4 sensors. The base station gives a single beep for the first sensor that is programmed, a double beep for the second, and so on. Additionally, multiple base stations can work with the same sensor to sound in different places. Carton Inventory Install 4 AA Alkaline batteries (not provided). (Lithium batteries recommended for colder environments.) Swivel Bushing LED light will flash. Passive Infra-Red (PIR) Motion Sensor Switch Settings Antenna PIR Sensor Sun/Rain Shield Mounting Plate PIR Motion Sensor Switch #1 Assembly & Test Test Switch #2 Button Step 1 Switch #1:. OFF 15' Detection Range ON 30' Detection Range (Default) Switch #2: OFF OFF Low Sensitivity 1 2 ON ON High Sensitivity Attach PIR Motion Sensor box to mounting plate with (Default) large silver screw. Tighten screw until PIR Motion Sensor stays in place when repositioned. NOTE: To avoid unwanted detection of small animals move Switch #2 to OFF. 1

Step 3 Programming PIR Motion Sensor to Base Station Step 5 Learn Button A Ensure Base A Station and PIR Motion Sensor are in close proximity to each other. Press and release learn button on Base Station. Buzzer will sound. B Insert battery pack facing away from circuit board and B Within 5 seconds, wave hand in front of PIR Motion attach cover. Sensor. Test light will illuminate and Base Station NOTE: Ensure the batteries do not touch the circuit will buzz. board and the antenna and battery wires are not pinched. PIR Motion Sensor Installation Step 6 Step 4 Mount PIR Motion Sensor horizontally on solid surface a few feet off the ground and within 900' of Base Station (rotate sensor to access screw holes). Unit should be able to swivel as needed. Attach sun/rain shield. NOTE: Keep PIR Motion Sensor antenna away from metal objects. Do not mount PIR Motion Sensor in direct sunlight, near moving tree branches, or in the path of a sprinkler system. Test PIR Motion Sensor by waving hand in front of sensor. Test light should flash. Secure cover with the smallest screws. 2

Vehicle Alert Installation: For cars, the best mounting position is about 4' high, between 10-20' back, and angled to see the back of car after passing the sensor. 10' - 20' 3' - 5' Troubleshooting The PIR Motion Sensor lights up, but the Base Base Station beeps every ten minutes. Station does not respond. The batteries in the Base Station are low. Replace The PIR Motion Sensor must be programmed to Base with 4 AA batteries or operate it using AC Adapter. Station (See Step 5). Ensure Base Station is on and is not muted. If the green power light is not lit or is flashing, press The Alert is not getting expected transmission the Mute Button on the top of the Base Station to range. wake it up. Keep both antennas vertical and keep PIR Motion If the green power is illuminated, look at the two small Sensor antenna away from trees and metal objects. white Base Station switches next to the Learn Button. Ensure Base Station is in clearest possible sight of The #1 Dip Switch should be down, towards the the PIR Motion Sensor. The less objects between the circuit board. If it is up, the Base Station has been devices, the longer the range. muted. If the Base Station signals when you press the Learn Button, it is not muted. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Changes or PIR Motion Sensor is detecting motion only part modifications not expressly approved by the of the time. manufacturer could void the user’s authority to To detect cars, it is best to mount PIR Motion Sensor operate the equipment. at height of car’s motor and have it between ten and twenty feet from the road. Swivel sensor as needed. The Alert is giving false alarms. Check for moving tree branches or insects in sensor window. PIR sensor can also be triggered by light shining directly in sensor window, such as reflected sunlight, or motion in front of a light source. It is possible that condensation has built up on the sensor. Wipe condensation from PIR Motion Sensor with cotton swab. Let it sit inside for a few hours, open to the air, without the batteries and it should correct itself. Check Sensor Switches on PIR Motion Sensor. See Switch Settings. 3

FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER: 1-800-528-9131 www.chamberlain-DIY.com NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. © 2008, The Chamberlain Group Inc. 114A3897 All Rights Reserved


Document Created: 2009-05-20 12:24:30
Document Modified: 2009-05-20 12:24:30
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC