Test report

FCC ID: JE4STAMP915

Test Report

Download: PDF
FCCID_3135639

DATE: 14 September 2016 I.T.L. (PRODUCT TESTING) LTD. FCC Radio Test Report For Risco Ltd. Equipment under test: 915 MHz RF Module RWTRSS10915A-40 Tested by: _____________________________ N. Levi Approved by: _____________________________ D. Shidlowsky This report must not be reproduced, except in full, without the written permission of I.T.L. (Product Testing) Ltd. This report relates only to items tested. Test Report E166600.01 Risco Ltd. Page 1 of 33 ITL FCCMASVE 1.25 26 March 2003

Measurement/Technical Report for Risco Ltd. Equipment under test: 915 MHz RF Module RWTRSS10915A-40 FCC ID: JE4STAMP915 This report concerns: Original Grant: X Class I change: Class II change: Equipment type: DXT – Part 15 Low Power Transceiver, Rx Verified. Limits used: 47CFR15 Section 15.249 Measurement procedure used is ANSI C63.10-2013. Application for Certification Applicant for this device: prepared by: (different from "prepared by") R. Pinchuck Motti Barad ITL (Product Testing) Ltd. Risco Ltd. 1 Bat Sheva Street 14 Hachoma St., Lod Rishon LeTzion 75655 Israel Israel Tel: +972-8-918-6100 Tel: +972-3-963-7777 Fax: +972-8-915-3101 Fax: +972-3-961-6584 Email: Rpinchuck@itl.co.il E-mail: Mottib@riscogroup.com Test Report E166600.01 Risco Ltd. Page 2 of 33 ITL FCCMASVE 1.25 26 March 2003

TABLE OF CONTENTS 1. GENERAL INFORMATION --------------------------------------------------------------------------- 4 1.1 Administrative Information ........................................................................... 4 1.2 List of Accreditations ................................................................................... 5 1.3 Product Description ..................................................................................... 6 1.4 Test Methodology ........................................................................................ 6 1.5 Test Facility ................................................................................................. 7 1.6 Measurement Uncertainty ........................................................................... 7 1.7 Ambient conditions ...................................................................................... 7 2. SYSTEM TEST CONFIGURATION ----------------------------------------------------------------- 8 2.1 Justification .................................................................................................. 8 2.2 EUT Exercise Software ............................................................................... 8 2.3 Special Accessories .................................................................................... 8 2.4 Equipment Modifications ............................................................................. 8 2.5 Configuration of Tested System .................................................................. 8 3. RADIATED MEASUREMENT TEST SET-UP PHOTOS -------------------------------------- 9 4. FIELD STRENGTH OF FUNDAMENTAL ------------------------------------------------------- 12 4.1 Test Specification ...................................................................................... 12 4.2 Test Procedure .......................................................................................... 12 4.3 Test Limits ................................................................................................. 12 4.4 Test Results............................................................................................... 12 4.5 Test Instrumentation Used; Field Strength of Fundamental ..................... 15 5. FIELD STRENGTH OF HARMONICS ----------------------------------------------------------- 16 5.1 Test Specification ...................................................................................... 16 5.2 Test Procedure .......................................................................................... 16 5.3 Test Limits ................................................................................................. 16 5.4 Test Results............................................................................................... 16 5.5 Test Instrumentation Used; Field Strength of Harmonics ......................... 19 5.6 Field Strength Calculation ......................................................................... 20 6. RADIATED EMISSION ------------------------------------------------------------------------------- 21 6.1 Test Specification ...................................................................................... 21 6.2 Test Procedure .......................................................................................... 21 6.3 Test Limits ................................................................................................. 21 6.4 Test Results............................................................................................... 21 6.5 Test Instrumentation Used; Radiated Emissions ...................................... 23 6.6 Field Strength Calculation ......................................................................... 24 7. ANTENNA INFO/GAIN ------------------------------------------------------------------------------- 25 8. R.F EXPOSURE/SAFETY --------------------------------------------------------------------------- 26 9. APPENDIX A - CORRECTION FACTORS ----------------------------------------------------- 27 9.1 Correction factors for CABLE ................................................................... 27 9.2 Correction factors for CABLE ................................................................... 28 9.3 Correction factors for CABLE ................................................................... 29 9.4 Correction factors for LOG PERIODIC ANTENNA .................................. 30 9.5 Correction factors for Biconical Antenna ................................................... 31 9.6 Correction factors for Horn ANTENNA ...................................................... 32 9.7 Correction factors for ACTIVE LOOP ANTENNA ..................................... 33 Test Report E166600.01 Risco Ltd. Page 3 of 33 ITL FCCMASVE 1.25 26 March 2003

1. General Information 1.1 Administrative Information Manufacturer: Risco Ltd. Manufacturer's Address: 14 Hachoma St. Rishon Le T’zion 75655 Israel Tel: +972-3-963-7777 Fax: +972-3-961-6584 Manufacturer's Representative: Motti Barad Equipment Under Test (E.U.T): 915 MHz RF Module Equipment Model No.: RWTRSS10915A-40 Equipment Serial No.: Not designated Date of Receipt of E.U.T: July 03, 2016 Start of Test: July 03, 2016 End of Test: July 11, 2016 Test Laboratory Location: I.T.L (Product Testing) Ltd. 1 Batsheva St., Lod ISRAEL 7120101 Test Specifications: FCC Part 15, Subpart C, Section 15.249 Test Report E166600.01 Risco Ltd. Page 4 of 33 ITL FCCMASVE 1.25 26 March 2003

1.2 List of Accreditations The EMC laboratory of I.T.L. is accredited by the following bodies: 1. The American Association for Laboratory Accreditation (A2LA) (U.S.A.), Certificate No. 1152.01. 2. The Federal Communications Commission (FCC) (U.S.A.), FCC Designation Number IL1005. 3. The Israel Ministry of the Environment (Israel), Registration No. 1104/01. 4. The Voluntary Control Council for Interference by Information Technology Equipment (VCCI) (Japan), Registration Numbers: C-3006, R-2729, T-1877, G-245. 5. Industry Canada (Canada), IC File No.: 46405-4025; Site No. IC 4025A-1, 4025A-2. I.T.L. Product Testing Ltd. is accredited by the American Association for Laboratory Accreditation (A2LA) and the results shown in this test report have been determined in accordance with I.T.L.'s terms of accreditation unless stated otherwise in the report. Test Report E166600.01 Risco Ltd. Page 5 of 33 ITL FCCMASVE 1.25 26 March 2003

1.3 Product Description Model Name RWTRSS10915A-40 Mode of Operation Transmitter Modulations 915MHz OOK Assigned Frequency Range 915MHz Operation Frequency 915MHz Transmit Power 8dBm Antenna Gain +3dBi 1.4 Test Methodology Radiated testing were performed according to the procedures in ANSI C63.10-2013. Radiated testing was performed at an antenna to EUT distance of 3 meters. Test Report E166600.01 Risco Ltd. Page 6 of 33 ITL FCCMASVE 1.25 26 March 2003

1.5 Test Facility Radiated emissions tests were performed at I.T.L.’s testing facility in Lod, Israel. I.T.L.’s EMC Laboratory is accredited by A2LA, certificate No. 1152.01 and its FCC Designation Number is IL1005. 1.6 Measurement Uncertainty Radiated Emission Radiated Emission (CISPR 11, EN 55011, CISPR 22, EN 55022, ANSI C63.4) for open site 30-1000MHz: Expanded Uncertainty (95% Confidence, K=2): ± 4.96 dB 1.7 Ambient conditions Temperature (32ºC- 22.7 ºC)/humidity (35.6%-41.1%) Test Report E166600.01 Risco Ltd. Page 7 of 33 ITL FCCMASVE 1.25 26 March 2003

2. System Test Configuration 2.1 Justification Testing was performed with the module transmitting modulated signal at 915.0 MHz while assembled on an evaluation board with a DC board. The DC board was connected to an AC/DC adapter. 2.2 EUT Exercise Software No special exercise software was needed to achieve compliance. 2.3 Special Accessories No special exercise software was needed to achieve compliance 2.4 Equipment Modifications No equipment modifications were needed to achieve compliance. 2.5 Configuration of Tested System 915MHz RS Switching Adapter Manufacturer Dong Guan Gao Yi Electronic Co. Ltd. EUT Model No: RSS1006-090090 115 Input: 100-240V-50/60Hz 0.3A VAC Output: 9.0 V 1.0A 9.0W Max Figure 1. Configuration of Tested System Test Report E166600.01 Risco Ltd. Page 8 of 33 ITL FCCMASVE 1.25 26 March 2003

3. Radiated Measurement Test Set-Up Photos Figure 2. Field Strength of Fundamental Test Figure 3. Radiated Emission Test Test Report E166600.01 Risco Ltd. Page 9 of 33 ITL FCCMASVE 1.25 26 March 2003

Figure 4. Radiated Emission Test Figure 5. Radiated Emission Test Test Report E166600.01 Risco Ltd. Page 10 of 33 ITL FCCMASVE 1.25 26 March 2003

Figure 6. Radiated Emission Test Test Report E166600.01 Risco Ltd. Page 11 of 33 ITL FCCMASVE 1.25 26 March 2003

4. Field Strength of Fundamental 4.1 Test Specification F.C.C., Part 15, Subpart C, Section 15.249(a) 4.2 Test Procedure The E.U.T operation mode and test set-up are as described in Section 2 of this report. The E.U.T was tested in the chamber, and placed on a remote-controlled turntable. The E.U.T was placed on a non-metallic table, 1.5 meters above the ground. The configuration tested is shown in Figure 2. The E.U.T was evaluated in the operation frequency of 915.0MHz. The readings were maximized by adjusting the turntable azimuth between 0-360°, and the antenna polarization 4.3 Test Limits Fundamental frequency Field strength of fundamental Field strength of fundamental (millivolts/meter) (dBuV/m) 902.0-928.0 MHz 50.0 94.0 2400-2483.5 MHz 50.0 94.0 5725.0-5875.0 MHz 50.0 94.0 24.0-24.25 GHz 250.0 108.0 *Field strength limits are specified at a distance of 3 meters ** for frequencies above 1000 MHz, the field strength limits of this section are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. 4.4 Test Results JUDGEMENT: Passed by 1.9dB The EUT met the FCC Part 15, Subpart C, Section 15.249(a) specification requirements. The details of the highest emissions are given in Figure 7 to Figure 9. Test Report E166600.01 Risco Ltd. Page 12 of 33 ITL FCCMASVE 1.25 26 March 2003

Field Strength of Fundamental E.U.T Description 915 MHz RF Module Model Number RWTRSS10915A-40 Serial Number: Not designated Specification: F.C.C., Part 15, Subpart C 15.249(a) Antenna Polarization: Horizontal/Vertical Test Distance: 3 meters Detector: Peak, Q.peak Freq. Axis Pol. Peak Q.peak Correction Total Limit Margin Reading Reading Factor* reading (MHz) (V/H) (dBµV/m) (dBµV/m) (dBµV/m) (dBµV/m) (dBµV/m) (dB) 915.0 H 67.5 67.1 25.0 92.1 94.0 -1.9 X 915.0 V 58.2 58.0 25.0 83.0 94.0 -11.0 915.0 H 63.8 63.5 25.0 88.5 94.0 -5.5 Y 915.0 V 66.6 66.3 25.0 91.3 94.0 -2.7 915.0 H 65.3 65.2 25.0 90.2 94.0 -3.8 Z 915.0 V 59.7 59.5 25.0 84.5 94.0 -9.5 Figure 7. Field Strength of Fundamental. Antenna Polarization: HORIZONTAL/VERTICAL. Detector: Peak Note: Margin refers to the test results obtained minus specified requirement; thus a positive number indicates failure, and a negative result indicates that the product passes the test. * “Correction Factors” = Antenna Correction Factor + Cable Loss. Test Report E166600.01 Risco Ltd. Page 13 of 33 ITL FCCMASVE 1.25 26 March 2003

Field Strength of Fundamental E.U.T Description 915 MHz RF Module Model Number RWTRSS10915A-40 Serial Number: Not designated Specification: F.C.C., Part 15, Subpart C 15.249(a) Antenna Polarization: Horizontal/Vertical Operation Frequency: 915.0MHz Test Distance: 3 meters Detector: Peak Figure 8. Field Strength of Fundamental. Antenna Polarization: HORIZONTAL Figure 9. Field Strength of Fundamental. Antenna Polarization: VERTICAL Test Report E166600.01 Risco Ltd. Page 14 of 33 ITL FCCMASVE 1.25 26 March 2003

4.5 Test Instrumentation Used; Field Strength of Fundamental Serial Last Calibration Next Calibration Instrument Manufacturer Model Number Date Date EMI Receiver R&S ESCI7 100724 February 29, 2016 March 1, 2017 Log Periodic EMCO 3146 9107-3158 March 24, 2016 March 24, 2017 Antenna Semi Anechoic ETS S81 SL 11643 N/A N/A Chamber Figure 10 Test Equipment Used Test Report E166600.01 Risco Ltd. Page 15 of 33 ITL FCCMASVE 1.25 26 March 2003

5. Field Strength of Harmonics 5.1 Test Specification FCC, Part 15, Subpart C, Section 249(a) 5.2 Test Procedure The E.U.T. operation mode and test set-up are as described in Section 2 of this report. The E.U.T was placed in the chamber and placed on a remote-controlled turntable. The E.U.T was placed on a non-metallic table, 1.5 meters above the ground. The configuration tested is shown in Figure 1. The frequency range 1000.0MHz-10,000MHz was scanned. RBW was set to 1000 kHz. The readings were maximized by adjusting the turntable azimuth between 0-360°, and the antenna polarization. The evaluation distance was 3 meters. 5.3 Test Limits Fundamental frequency Field strength of harmonics Field strength of harmonics (MHz) (microvolts/meter) (dBuV/m) 902.0-928.0 MHz 500.0 54.0 2400-2483.5 MHz 500.0 54.0 5725.0-5875.0 MHz 500.0 54.0 24.0-24.25 GHz 2500.0 68.0 * for frequencies above 1000 MHz, the field strength limits of this section are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. 5.4 Test Results JUDGEMENT: Passed The EUT met the requirements of the F.C.C. Part 15, Subpart C, Section 209 specification. For additional information see Figure 11 and Figure 12. Test Report E166600.01 Risco Ltd. Page 16 of 33 ITL FCCMASVE 1.25 26 March 2003

Field Strength of Harmonics E.U.T Description 915 MHz RF Module Type RWTRSS10915A-40 Serial Number: Not designated Specification: FCC Part 15, Subpart C Antenna Polarization: Horizontal/Vertical Frequency Range: 30 MHz to 10.0 GHz Test Distance: 3 meters Detector: Average Operation Frequency: 915.0MHz Freq. Polarity Avg Limit Margin (MHz) (H/V) (dBµV/m) (dBµV/m) (dB) X Y Z 1829.9 H 35.1 35.3 35.4 54.0 -18.6 1829.9 V 36.2 36.5 36.0 54.0 -17.5 2745.3 H 37.4 37.6 37.7 54.0 -16.3 2744.9 V 36.8 37.0 37.3 54.0 -16.7 5490.0 H 39.2 39.7 39.5 54.0 -14.3 5489.5 V 40.3 40.8 40.9 54.0 -13.1 Figure 11. Field Strength of Harmonics. Antenna Polarization: AVG -HORIZONTAL / VERTICAL. Test Report E166600.01 Risco Ltd. Page 17 of 33 ITL FCCMASVE 1.25 26 March 2003

Field Strength of Harmonics E.U.T Description 915 MHz RF Module Type RWTRSS10915A-40 Serial Number: Not designated Specification: FCC, Part 15, Subpart C Antenna Polarization: Horizontal/Vertical Frequency Range: 30 MHz to 10.0 GHz Test Distance: 3 meters Detector: Peak Operation Frequency: 915.0MHz Freq. Polarity Peak Limit Margin (MHz) (H/V) (dBµV/m) (dBµV/m) (dB) X Y Z 1829.9 H 41.3 41.4 41.0 74.0 -32.6 1829.9 V 42.2 42.5 42.7 74.0 -31.3 2745.3 H 43.7 44.2 44.7 74.0 -29.3 2744.9 V 44.1 44.5 44.8 74.0 -29.2 5490.0 H 50.1 50.3 49.7 74.0 -23.7 5489.5 V 50.2 49.6 50.3 74.0 -23.7 Figure 12. Field Strength of Harmonics. Antenna Polarization: Peak -HORIZONTAL / VERTICAL. Margin refers to the test results obtained minus specified requirement; thus a positive number indicates failure, and a negative result indicates that the product passes the test. “Peak Amp” includes correction factor. * “Correction Factor” = Antenna Factor + Cable Loss- Low Noise Amplifier Gain Test Report E166600.01 Risco Ltd. Page 18 of 33 ITL FCCMASVE 1.25 26 March 2003

5.5 Test Instrumentation Used; Field Strength of Harmonics Instrument Manufacturer Model Serial No. Last Last Calibration Calibration Date Date EMI R&S ESCI7 100724 February 29, 2016 March 1, 2017 Receiver Spectrum HP 8592L 3826A01204 March 13, 2016 March 13, 2017 Analyzer Active Loop EMCO 6502 9506-2950 November 5, 2015 November 30, 2016 Antenna Biconical EMCO 3110B 9912-3337 March 24, 2016 March 24, 2018 Antenna Log Periodic EMCO 3146 9505-4081 April 23, 2016 April 23, 2017 Antenna 1G-18GHz Horn ETS 3115 29845 May 19, 2015 May 19, 2018 Antenna Antenna ETS 2070-2 9608-1497 N/A N/A Mast Turntable ETS 2087 - N/A N/A Mast & Table ETS/EMCO 2090 9908-1456 N/A N/A Controller Figure 13 Test Equipment Used Test Report E166600.01 Risco Ltd. Page 19 of 33 ITL FCCMASVE 1.25 26 March 2003

5.6 Field Strength Calculation The field strength is calculated directly by the EMI Receiver software, and a "Correction Factors" data disk, using the following equation: FS = RA + AF + CF FS: Field Strength [dBv/m] RA: Receiver Amplitude [dBv] AF: Receiving Antenna Correction Factor [dB/m] CF: Cable Attenuation Factor [dB] Example: FS = 30.7 dBV (RA) + 14.0 dB (AF) + 0.9 dB (CF) = 45.6 dBV No external pre-amplifiers are used. Test Report E166600.01 Risco Ltd. Page 20 of 33 ITL FCCMASVE 1.25 26 March 2003

6. Radiated Emission 6.1 Test Specification Part 15, Subpart C, Section 15.249(d) 6.2 Test Procedure The E.U.T. operation mode and test set-up are as described in Section 2 of this report. For measurements between 0.009MHz -30.0MHz: The E.U.T was tested inside the shielded room and placed on a non-metallic table, 1.5 meters above the ground. The frequency range 0.009MHz-30.0MHz was scanned. The readings were maximized by the turntable azimuth between 0-360°, and the antenna polarization. For 30.0MHz-1000.0MHz range: A preliminary measurement to characterize the E.U.T was performed inside the shielded room at a distance of 3 meters, using peak detection mode and broadband antennas. The preliminary measurements produced a list of the highest emissions. The E.U.T was then transferred to the open site, and placed on a remote-controlled turntable. The E.U.T was placed on a non-metallic table, 0.8 meters above the ground. The configuration tested is shown in Figure 1. The frequency range 0.009 MHz-1000 MHz was scanned. RBW was set to 100 kHz. The readings were maximized by adjusting the antenna height between 1-4 meters, the turntable azimuth between 0-360°, and the antenna polarization. For 1000.0MHz-10,000.0MHz range: The E.U.T was placed in the chamber and placed on a remote-controlled turntable. The E.U.T was placed on a non-metallic table, 1.5 meters above the ground. The configuration tested is shown in Figure 1. The frequency range 1000.0MHz-10,000MHz was scanned. RBW was set to 1000 kHz. The readings were maximized by adjusting the turntable azimuth between 0-360°, and the antenna polarization. For all final evaluations the distance was 3 meters. 6.3 Test Limits Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in §15.209, whichever is the lesser attenuation. 6.4 Test Results JUDGEMENT: Passed The margin between the emission level and the specification limit was 4.5 dB in the worst case at the frequency of 64.8 MHz, vertical polarization. The EUT met the requirements of the F.C.C. Part 15, Subpart C, Section 15.249 specification. Test Report E166600.01 Risco Ltd. Page 21 of 33 ITL FCCMASVE 1.25 26 March 2003

Radiated Emission E.U.T Description 915 MHz RF Module Type RWTRSS10915A-40 Serial Number: Not designated Specification: FCC, Part 15, Subpart C Antenna Polarization: Horizontal/Vertical Frequency range: 30 MHz to 10.0 GHz Test Distance: 3 meters Detector: Peak Operation Frequency: 915.0MHz Freq. Polarity Peak Q.Peak Limit Margin (MHz) (H/V) (dBµV/m) (dBµV/m) (dBµV/m) (dB) 64.8 H 26.6 20.3 40.0 -13.4 64.8 V 35.5 25.7 40.0 -4.5 125.7 H 29.1 22.7 43.5 -14.4 125.7 V 32.2 25.3 43.5 -11.3 159.6 H 33.3 26.9 43.5 -10.2 159.6 V 32.2 25.2 43.5 -11.3 Figure 14. Radiated Emission. Antenna Polarization: HORIZONTAL / VERTICAL. Detector: Peak Margin refers to the test results obtained minus specified requirement; thus a positive number indicates failure, and a negative result indicates that the product passes the test. “Peak Amp” includes correction factor. * “Correction Factor” = Antenna Factor + Cable Loss- Low Noise Amplifier Gain Test Report E166600.01 Risco Ltd. Page 22 of 33 ITL FCCMASVE 1.25 26 March 2003

6.5 Test Instrumentation Used; Radiated Emissions Instrument Manufacturer Model Serial No. Last Next Calibration Calibration Date Date EMI Receiver R&S ESCI7 100724 February 29, 2016 March 1, 2017 Spectrum HP 8592L 3826A01204 March 13, 2016 March 13, 2017 Analyzer Active Loop EMCO 6502 9506-2950 November 5, 2015 November 30, 2016 Antenna Biconical EMCO 3110B 9912-3337 March 24, 2016 March 24, 2018 Antenna Log Periodic EMCO 3146 9505-4081 April 23, 2016 April 23, 2017 Antenna 1G-18GHz ETS 3115 29845 May 19, 2015 May 19, 2018 Horn Antenna Antenna Mast ETS 2070-2 9608-1497 N/A N/A Turntable ETS 2087 - N/A N/A Mast & Table ETS/EMCO 2090 9608-1456 N/A N/A Controller Figure 15 Test Equipment Used Test Report E166600.01 Risco Ltd. Page 23 of 33 ITL FCCMASVE 1.25 26 March 2003

6.6 Field Strength Calculation The field strength is calculated directly by the EMI Receiver software, and a "Correction Factors" data disk, using the following equation: [dBv/mFS = RA + AF + CF FS: Field Strength [dBv/m] RA: Receiver Amplitude [dBv] AF: Receiving Antenna Correction Factor [dB/m] CF: Cable Attenuation Factor [dB] Test Report E166600.01 Risco Ltd. Page 24 of 33 ITL FCCMASVE 1.25 26 March 2003

7. Antenna Info/Gain +3.0dBi Test Report E166600.01 Risco Ltd. Page 25 of 33 ITL FCCMASVE 1.25 26 March 2003

8. R.F Exposure/Safety Typical use of the E.U.T. is as a module in alarm system units. The typical placement of the E.U.T. is in alarm detectors, control panels, keypads. The typical distance between the E.U.T. and the user is greater than 20 cm. Calculation of Maximum Permissible Exposure (MPE) Based on Section 1.1310 Requirements �� �� (a) FCC limits at 915 MHz is: (f/1500) = 915/1500=.61 ��2 ��2 Using table 1 of Section 1.1310 limit for general population/uncontrolled exposures, the above level is an average over 30 minutes. (b) The power density produced by the E.U.T. is Pt Gt S 4R 2 Pt- Transmitted Power 92.1dBuV/m (Peak) = -3.1dBm = 0.49mW (testing performed conducted, power calculation contains antenna gain) GT- Antenna Gain, +3.0dBi R- Distance from Transmitter using 20cm (c) The peak power density is: 0.49 mW Sp   9.75 x10  5 4 (20) 2 cm2 (d) This is below the FCC limit. Test Report E166600.01 Risco Ltd. Page 26 of 33 ITL FCCMASVE 1.25 26 March 2003

9. APPENDIX A - CORRECTION FACTORS 9.1 Correction factors for CABLE from EMI receiver to test antenna at 3 meter range. Cable Cable Frequency Frequency Loss Loss (MHz) (dB) (MHz) (dB) 0.010 0.4 50.00 1.2 0.015 0.2 100.00 0.7 0.020 0.2 150.00 2.1 0.030 0.3 200.00 2.3 0.050 0.3 300.00 2.9 0.075 0.3 500.00 3.8 0.100 0.2 750.00 4.8 0.150 0.2 1000.00 5.4 0.200 0.3 1500.00 6.7 0.500 0.4 2000.00 9.0 1.00 0.4 2500.00 9.4 1.50 0.5 3000.00 9.9 2.00 0.5 3500.00 10.2 5.00 0.6 4000.00 11.2 10.00 0.8 4500.00 12.1 15.00 0.9 5000.00 13.1 20.00 0.8 5500.00 13.5 6000.00 14.5 NOTES: 1. The cable type is SPUMA400 RF-11N(X2) and 39m long 2. The cable is manufactured by Huber + Suhner Test Report E166600.01 Risco Ltd. Page 27 of 33 ITL FCCMASVE 1.25 26 March 2003

9.2 Correction factors for CABLE from EMI receiver to test antenna at 3 meter range (chamber). Cable Cable Frequency Frequency Loss Loss (GHz) (dB) (MHz) (dB) 1.0 -1.5 11.0 -6.1 2.0 -2.1 12.0 -6.1 3.0 -2.7 13.0 -6.2 4.0 -3.1 14.0 -6.7 5.0 -3.5 15.0 -7.4 6.0 -4.1 16.0 -7.5 7.0 -4.6 17.0 -7.9 8.0 -4.9 18.0 -8.1 9.0 -5.7 19.0 -8.8 10.0 -5.7 20.0 -9.1 NOTES: 1. The cable type is 0623 WBC-400 and 39m long 2. The cable is manufactured by COMMSCOPE Test Report E166600.01 Risco Ltd. Page 28 of 33 ITL FCCMASVE 1.25 26 March 2003

9.3 Correction factors for CABLE from EMI receiver to test antenna at 3 meter range additional cable(chamber). Cable Cable Frequency Frequency Loss Loss (GHz) (dB) (MHz) (dB) 1.0 -0.3 10.0 -0.1 2.0 -0.5 11.0 -2.0 3.0 -0.7 12.0 -0.4 4.0 -0.7 13.0 -2.9 5.0 -0.7 14.0 -3.3 6.0 -1.0 15.0 -1.6 7.0 -0.3 16.0 -2.6 8.0 -0.4 17.0 -1.4 9.0 -0.7 18.0 -1.4 NOTES: 1. The cable type is 705A009301 EIM and 1m long 2. The cable is manufactured by Huber Zhuner Test Report E166600.01 Risco Ltd. Page 29 of 33 ITL FCCMASVE 1.25 26 March 2003

9.4 Correction factors for LOG PERIODIC ANTENNA Model: 3146 Antenna serial number: 9505-4081 3 meter range AF Frequency [MHz] [dB/m] 200.0 11.47 250.0 12.06 300.0 14.77 400.0 15.77 500.0 18.01 600.0 18.84 700.0 20.93 800.0 21.27 900.0 22.44 1000.0 24.10 Test Report E166600.01 Risco Ltd. Page 30 of 33 ITL FCCMASVE 1.25 26 March 2003

9.5 Correction factors for Biconical Antenna Model: EMCO 3110B serial number: 9912-3337 3 meter range AF Frequency [MHz] [dB/m] 30.0 14.18 35.0 13.95 40.0 12.84 45.0 11.23 50.0 11.10 60.0 10.39 70.0 9.34 80.0 9.02 90.0 9.31 100.0 8.95 120.0 11.53 140.0 12.20 160.0 12.56 180.0 13.49 200.0 15.27 Test Report E166600.01 Risco Ltd. Page 31 of 33 ITL FCCMASVE 1.25 26 March 2003

9.6 Correction factors for Horn ANTENNA Model: 3115 Antenna serial number: 29845 10 meter range FREQUENCY AFE FREQUENCY AFE (MHz) (dB/m) (MHz) (dB/m) 1000 22.4 10000 36.1 2000 25.2 11000 37.0 3000 31.1 12000 41.3 4000 30.2 13000 38.1 5000 34.2 14000 41.7 6000 31.6 15000 39.0 7000 34.7 16000 38.8 8000 34.8 17000 43.2 9000 36.2 18000 43.7 Test Report E166600.01 Risco Ltd. Page 32 of 33 ITL FCCMASVE 1.25 26 March 2003

9.7 Correction factors for ACTIVE LOOP ANTENNA Model 6502 S/N 9506-2950 Magnetic Electric FREQUENCY Antenna Antenna Factor Factor (MHz) (dB) (dB) .009 -35.1 16.4 .010 -35.7 15.8 .020 -38.5 13.0 .050 -39.6 11.9 .075 -39.8 11.8 .100 -40.0 11.6 .150 -40.0 11.5 .250 -40.0 11.6 .500 -40.0 11.5 .750 -40.1 11.5 1.000 -39.9 11.7 2.000 -39.5 12.0 3.000 -39.4 12.1 4.000 -39.7 11.9 5.000 -39.7 11.8 10.000 40.2 11.3 15.000 -40.7 10.8 20.000 -40.5 11.0 25.000 -41.3 10.2 30.000 -42.3 9.2 Test Report E166600.01 Risco Ltd. Page 33 of 33 ITL FCCMASVE 1.25 26 March 2003


Document Created: 2017-12-14 18:28:01
Document Modified: 2017-12-14 18:28:01
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC