User Manual

FCC ID: JE4RWT6G915

Users Manual

Download: PDF
FCCID_3073559

8). 4. Mount the Wireless VITRON on the required location (wall or 3 Mounting Location ceiling) using the supplied screws (2, Fig 8). Do not tighten the screws. For optimal performance the Wireless VITRON should be mounted as 5. Adjust the detector so it will face the protected glass. nearly opposite to the glass area to be protected, as shown in Fig 3. 6. Tighten the bolts to the final torque. Attach the Glassbreak detector to the surface using the adhesive strips. Model: RWT6G • Opposite Wall –Mounted (For optimal results, Wireless VITRON is centered 6 Quick Device Allocation at the Control Panel opposite glass, see Fig. 3). VITRON The Glassbreak detector is automatically programmed to your control panel during the on-line installation wizard setup. If you later Installation instructions Fig. 3 purchase an extra detector you can enroll it as follows: To quickly allocate the detector at the control panel: • Ceiling Mounted (for optimal results If the control panel is not already in Learn mode, press the Wireless VITRON is centered and directed towards protected glass, using the supplied button on the control panel for 5 seconds; the unit beeps once VITRON VITRON swivel adaptor, see fig. 4) as it enters Learn mode (all the LEDs also light up, one after the other). Fig. 4 Remove the plastic wrapping from the batteries before installation and make sure the cover is removed so the internal tamper switch is • Corner Mounted (choose corner opposite accessible. glass to be protected see fig. 5) Send a signal transmission from the detector by pressing the tamper button for at least 2 seconds; the control panel beeps once to accept 1 General Description VITRON VI TRO N or beeps three times to reject. Once accepted, the system VITRON VI TRON announces the device type and its zone (for example, “Detector, The Wireless VITRON is an advanced microprocessor based Fig. 5 zone 1”). Acoustic Glass Break detector. The Wireless VITRON detects the When the detectors have been enrolled, short-press the control breaking of most common types of framed glass panes while • Side wall – mounted not recommended ignoring false alarms. due to the fact that the Wireless VITRON is panel button to exit Learn mode; the unit beeps once and the LEDs stop flashing. not opposite the glass - see range versus Note: For future use, it is recommended to write down the detector angle diagram (Fig 2). VITRON VITRON 2 Installation Procedure description, zone number, and installation location of each allocated Fig. 6 detector. Note: To improve detection, It is highly recommended to use a Notes: swivel adaptor, especially for ceiling and wall installations. 45° Do not mount Wireless VITRON on same wall as the protected glass. 7 Jumpers settings 60° 30° Fig 1: Percentage of Maximum Avoid installing the Wireless VITRON near sources of loud noise or 75° Range as a function of angle vibrations (air conditioners, fans, compressors, stereos, etc). Please do not change the jumper settings. 15° between Wireless VITRON and Avoid defining the Wireless VITRON as a 24 hour zone 0° glass. The Wireless VITRON should always be installed in addition to 8 Technical Specifications standard motion detectors Electrical WIRELESS VITRON Current consumption 22 uA at 3 VDC, without acoustic 4 Mounting (standby) signal Verify that the distance between the Wireless VITRON and the furthest point on the protected glass does not exceed the maximum Use the two-sided adhesive tape to attach the detector to the surface. Current consumption 10 mA at 3 VDC specified range taking into account the reduced range due to angle (Alarm transmission) (Max. with LED OFF) (see Fig 2). 5 Swivel Mounting 15 mA at 3 VDC Fig 2: Angle between Wireless (Max. with LED ON) VITRON and glass When installing the Wireless Battery life 3 years, at 65 minutes supervision VITRON with the supplied swivel Range (loss) 300m (1000 feet) mounting adaptor, maximum 2 Voltage requirements CR123A 3VDC Lithium Batteries installation flexibility and Frequency 915MHz performance is achieved. Physical To install the swivel mounting Size 87 x 50.7 x 28.6 mm Other factors affecting range: adaptor perform the following: (LxWxD) (3.4 x 2.0 x 1.1 in.) • There should be no obstructions between the Wireless VITRON 1. Remove the PCB from the and the protected glass. Environmental Wireless VITRON back plate Operating/Storage 0°C to 50°C (-32°F to 122°F) • Curtains and blinds may reduce the effective range. 2. Open the swivel mounting • Sound absorbing materials in the protected area may reduce the temperature adaptor knockouts (4, Fig 7). range. 1 * Specifications are subject to change without prior notice 3. Attach the swivel mounting adaptor to the back plate using Fig. 8 Note: The detector contains a swivel. the two supplied screws (1, Fig

RISCO Group Limited Warranty RISCO Group and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in materials and workmanship under normal use for 24 months from the date of production. Because Seller does not install or connect the product and because the product may be used in conjunction with products not manufactured by the Seller, Seller can not guarantee the performance of the security system which uses this product. Sellers' obligation and liability under this warranty is expressly limited to repairing and replacing, at Sellers option, within a reasonable time after the date of delivery, any product not meeting the specifications. Seller makes no other warranty, expressed or implied, and makes no warranty of merchantability or of fitness for any particular purpose. In no case shall seller be liable for any consequential or incidental damages for breach of this or any other warranty, expressed or implied, or upon any other basis of liability whatsoever. Sellers obligation under this warranty shall not include any transportation charges or costs of installation or any liability for direct, indirect, or not be compromised or circumvented; that the product will prevent any persona; injury or property loss by intruder, robbery, fire or otherwise; or that the product will in all cases provide adequate warning or protection. Buyer understands that a properly installed and maintained alarm may only reduce the risk of intruder, robbery or fire without warning, but is not insurance or a guaranty that such will not occur or that there will be no personal injury or property loss as a result. Consequently seller shall have no liability for any personal injury, property damage or loss based on a claim that the product fails to give warning. However, if seller is held liable, whether directly or indirectly, for any loss or damage arising from under this limited warranty or otherwise, regardless of cause or origin, sellers maximum liability shall not exceed the purchase price of the product, which shall be complete and exclusive remedy against seller. No employee or representative of Seller is authorized to change this warranty in any way or grant any other warranty. WARNING: This product should be tested at least once a week. CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to local regulations. FCC ID: JE4RWT6G915 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation Changes or modifications to this equipment which are not expressly approved by the party responsible for compliance (RISCO Group's.) could void the user's authority to operate the equipment. FCC Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on to a different circuit from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. © RISCO Group 07/16 5IN2582


Document Created: 2016-07-11 14:36:38
Document Modified: 2016-07-11 14:36:38
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC