Test Report

FCC ID: JE4RW132KPP1356

Test Report

Download: PDF
FCCID_3084525

S T RADIO TEST REPORT Report No: STS1606212F01 S Issued for RISCO LTD. 14 Hachoma Street,Rishon Lezion,75655,Israel L Product Name: Brand Name: 2W WL LCD Keypad, 915 RISCO A Model Name: Series Model: RW132KPPW3 N/A B FCC ID: Test Standard: JE4RW132KPP1356 FCC Part 15.225 Any reproduction of this document must be done in full. No single part of this document may be reproduced without permission from STS, All Test Data Presented in this report is only applicable to presented Test sample. Shenzhen STS Test Services Co., Ltd. 1/F., Building B, Zhuoke Science Park, No.190,Chongqing Road, Fuyong Street, Bao’an District, Shenzhen, Guangdong,China TEL: +86-755 3688 6288 FAX: +86-755 3688 6277 E-mail:sts@stsapp.com

Page 2 of 24 Report No.: STS1606212F01 TEST REPORT CERTIFICATION Applicant’s name ................. : RISCO LTD. Address .................................. : 14 Hachoma Street,Rishon Lezion,75655,Israel Manufacture's Name ............ : RISCO LTD. Address .................................. : Sderot Yahalom 6 Kiryat Gat, Israel Product description Product name ............................ : 2W WL LCD Keypad, 915 Model and/or type reference : RW132KPPW3 Serial Model .............................. : N/A Standards ............................. : FCC Part15.225 Test procedure ...............................ANSI : C63.10: 2013,ANSI C63.4: 2014 This device described above has been tested by STS, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of STS, thidocument may be altered or revised by STS, personal only, and shall be noted in the revision of the document. Date of Test ............................................: Date (s) of performance of tests..............: 27June. 2016 ~05 July. 2016 Date of Issue ...........................................: 06 July. 2016 Test Result ...............................................: Pass Testing Engineer : (Tony Liu) Technical Manager : (Vita Li) Authorized Signatory : (Bovey Yang)

Page 3 of 24 Report No.: STS1606212F01 TABLE OF CONTENTS Page 1. SUMMARY OF TEST RESULTS 5 1.1 TEST FACTORY 5 1.2 MEASUREMENT UNCERTAINTY 5 2. GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF EUT 6 2.2 DESCRIPTION OF TEST MODES 7 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 7 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 8 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 9 3. EMC EMISSION TEST 10 3.1 CONDUCTED EMISSION MEASUREMENT 10 3.2 TEST PROCEDURE 11 3.3 TEST SETUP 11 3.4 EUT OPERATING CONDITIONS 11 3.5 TEST RESULTS 12 4. RADIATED EMISSION MEASUREMENT 13 4.1 RADIATED EMISSION LIMITS 13 4.2 TEST PROCEDURE 14 4.3 TEST SETUP 15 4.4 EUT OPERATING CONDITIONS 15 5. FREQUENCY TOLERANCE 19 5.1 REQUIREMENT 19 5.2 TEST PROCEDURE 19 5.3 TEST SETUP 19 5.4 EUT OPERATION CONDITIONS 19 5.5 TEST RESULTS 20 6. 20DB BANDWIDTH 21 6.1 APPLIED PROCEDURES / LIMIT 21 6.2 TEST PROCEDURE 21 6.3 TEST SETUP 21 6.4 EUT OPERATION CONDITIONS 21 6.5 TEST RESULTS 22

Page 4 of 24 Report No.: STS1606212F01 TABLE OF CONTENTS Page 7. ANTENNA REQUIREMENT 23 7.1 STANDARD REQUIREMENT 23 7.2 EUT ANTENNA 23 APPENDIX 1- PHOTOS OF TEST SETUP 24

Page 5 of 24 Report No.: STS1606212F01 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 15.225 , Subpart C Standard Test Item Judgment Remark Section 15.207 Conducted Emission N/A -- 15.209 Radiated Emission PASS -- 15.225(a)(b)(c)(d) 15.225(e) Frequency Tolerance PASS -- 15.203 Antenna Requirement PASS -- 15.215 20dB Bandwidth PASS -- NOTE: (1)” N/A” denotes test is not applicable in this Test Report (2) All tests are according to ANSI C63.4-2014 and ANSI C63.10-2013 1.1 TEST FACTORY Shenzhen STS Test Services Co., Ltd. 1/F., Building B, Zhuoke Science Park, No.190, Chongqing Road, Fuyong Street, Bao’an District, Shenzhen, Guangdong,China CNAS Registration No.: L7649; FCC Registration No.: 842334; IC Registration No.: 12108A-1 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission (9KHz-150KHz) ±2.88dB 2 Conducted Emission (150KHz-30MHz) ±2.67dB 3 RF power,conducted ±0.70dB 4 Spurious emissions,conducted ±1.19dB 5 All emissions,radiated(<1G) 30MHz-200MHz ±2.83dB 6 All emissions,radiated(<1G) 200MHz-1000MHz ±2.94dB 8 Temperature ±0.5°C 9 Humidity ±2%

Page 6 of 24 Report No.: STS1606212F01 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment 2W WL LCD Keypad, 915 Trade Name RISCO Model Name RW132KPPW3 Serial Model N/A Model Difference N/A The EUT is a 2W WL LCD Keypad, 915 Operation Frequency: 13.56MHz Product Description Modulation Type: OOK Antenna Designation: Please see Note 3. Antenna Gain (dBi) 3 dbi Battery DC 3V,20mA Hardware version number G1 Software versioning number V4.25 Connecting I/O Port(s) Please refer to the User's Manual Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. 2. Table for filed Antenna Ant. Brand Model Name Antenna Type Connector Gain (dBi) NOTE A RISCO RW132KPPW3 Spring Antenna N/A 3 ANT

P 1 ua» / Page 7 of 24 CecGe cce 2.2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre—scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 TX Mode For Radiated Emission Final Test Mode Description Mode 1 TX Mode Note: new battery is used during all test 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED E—1 1/F., Building 8, Zhuoke Science Park, No.190,Chongging Road, Fuyong Street, Bac‘an Distrct, Shenzhen, Guangdong,China Shenzhen STS Test Services Co., Ltd. Tel: 0755—36886288 Fax: 0755—36886277 Httpy//wnwstsapp.com E—mail:sts@stsapp.com

Page 8 of 24 Report No.: STS1606212F01 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Mfr/Brand Model/Type No. Serial No. Note 2W WL LCD E-1 RISCO RW132KPPW3 N/A EUT Keypad, 915 Item Shielded Type Ferrite Core Length Note N/A N/A N/A N/A N/A Note: (1)The support equipment was authorized by Declaration of Confirmation. (2)For detachable type I/O cable should be specified the length in cm in『Length』column.

Page 9 of 24 Report No.: STS1606212F01 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS Radiation Test equipment Kind of Equipment Manufacturer Type No. Serial No. Last calibration Calibrated until Spectrum Agilent E4407B MY50140340 2015.10.25 2016.10.24 Analyzer Test Receiver R&S ESCI 101427 2015.10.25 2016.10.24 Bilog Antenna TESEQ CBL6111D 34678 2015.11.25 2016.11.24 BBHA Horn Antenna Schwarzbeck 9120D(1201) 9120D-1343 2016.03.06 2017.03.05 1G-18G 50Ω Coaxial Anritsu MP59B 6200264416 2016.06.06 2017.06.05 Switch PreAmplifier Agilent 8449B 60538 2015.10.25 2016.10.24 Loop Antenna ARA PLA-1030/B 1029 2016.06.08 2017.06.07 USB RF power 15I00041SNO0 DARE RPR3006W 2015.10.25 2016.10.24 sensor 3 Spectrum Agilent E4407B MY50140340 2015.10.25 2016.10.24 Analyzer Conduction Test equipment Kind of Equipment Manufacturer Type No. Serial No. Last calibration Calibrated until EMI Test Receiver R&S ESPI 102086 2014.11.20 2016.11.19 LISN R&S ENV216 101242 2015.10.25 2016.10.24 LISN EMCO 3810/2NM 000-23625 2015.10.25 2016.10.24

Page 10 of 24 Report No.: STS1606212F01 3. EMC EMISSION TEST 3.1 CONDUCTED EMISSION MEASUREMENT 3.1.1 POWER LINE CONDUCTED EMISSION LIMITS Operating frequency band. In case the emission fall within the restricted band specified on Part 15. 207(a) limit in the table below has to be followed. Class B (dBuV) FREQUENCY (MHz) Standard Quasi-peak Average 0.15 -0.5 66 - 56 * 56 - 46 * CISPR 0.50 -5.0 56.00 46.00 CISPR 5.0 -30.0 60.00 50.00 CISPR 0.15 -0.5 66 - 56 * 56 - 46 * FCC 0.50 -5.0 56.00 46.00 FCC 5.0 -30.0 60.00 50.00 FCC Note: (1) The tighter limit applies at the band edges. (2) The limit of " * " marked band means the limitation decreases linearly with the logarithm of the frequency in the range. The following table is the setting of the receiver Receiver Parameters Setting Attenuation 10 dB Start Frequency 0.15 MHz Stop Frequency 30 MHz IF Bandwidth 9 kHz

Page 11 of 24 Report No.: STS1606212F01 3.2 TEST PROCEDURE a.The EUT was placed 0.4 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b.Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. c.I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d.LISN at least 80 cm from nearest part of EUT chassis. e.For the actual test configuration, please refer to the related Item –EUT Test Photos. 3.3 TEST SETUP Vertical Reference Ground Plane Test Receiver EUT 40cm 80cm LISN Horizontal Reference Ground Plane Note: 1.Support units were connected to second LISN. 2.Both of LISNs (AMN) are 80 cm from EUT and at least 80 cm from other units and other metal planes support. units. 3.4 EUT OPERATING CONDITIONS The EUT was configured for testing in a typical fashion (as a customer would normally use it). The EUT has been programmed to continuously transmit during test. This operating condition was tested and used to collect the included data.

3 \— EeePen CecGe cce 3.5 TEST RESULTS Temperature : 26 °C Relative Humidity : 54% Pressure : 1010hPa Phase : L/N Test Voltage : DC 3V Test Mode : N/A Do not apply 1/F., Building 8, Zhuoke Science Park, No.190,Chongging Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong,China Shenzhen STS Test Services Co., Ltd. Tel: 0755—36886288 Fax:0755—36886277 Http//www.stsapp.com E—mail:sts@stsapp.com

P \— Page 13 of 24 Report No.: STS1606212F01 4. RADIATED EMISSION MEASUREMENT 4.1 RADIATED EMISSION LIMITS (a) The field strength of any emissions within the band 13.553—13.567 MHz shall not exceed 15,848 microvolts/meter at 30 meters. (b) Within the bands 13.410—13.553 MHz and 13.567—13.710 MHz, the field strength of any emissions shall not exceed 334 microvolts/meter at 30 meters. (c) Within the bands 13.110—13.410 MHz and 13.710—14.010 MHz the field strength of any emissions shall not exceed 106 microvolts/meter at 30 meters. (d) The field strength of any emissions appearing outside of the 13.110—14.010 MHz band shall not exceed the general radiated emission limits in §15.209. LIMITS OF RADIATED EMISSION MEASUREMENT (Frequency Range 9kHz—1000MHz) Frequency range (MHz) Field Strength Field Strength@3m uV/m(@distance) dBuV/m 0.009—0.490 2400/F(kHz) (@300m) —— 0.490—1.705 24000/F(kHz) (@30m) —— 1.705—13.110 30 (@30m) 69.54 13.110 ~18.410 106 (@30m) 80.51 13.410 ~ 13.553 334 (@30m) 90.47 13.553 ~18.617 15.848 (@30m) 124.00 13.617 ~13.710 334 (@30m) 90.47 13.710 ~14.010 106 (@30m) 80.51 14.010—30 30 (@3m) 69.54 30—88 100 (@3m) 40.00 88~216 150 (@3m) 43.52 216~960 200 (@3m) 46.02 Above 960 500 (@3m) 53.98 NOTE: a) Field Strength (dBuV/m) = 20*log[Field Strength (uV/m)]. b) In the emission tables above, the tighter limit applies at the Band edge. Radiated Emission >30MHz (30MHz—1GHz, E—field) According to FCC section 15.205, the field strength of radiated emissions from intentiona radiators at a distance of 3 meters shall not exceed the following values: 1/F., Building 8, Zhuoke Science Park, No.190,Chongging Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong,China Shenzhen STS Test Services Co., Ltd. Tel: 0755—36886288 Fax:.0755—36886277 Http//wwwstsapp.com E—mail:sts@stsapp.com

Page 14 of 24 Report No.: STS1606212F01 Frequencies Field Strength Measurement Distance (MHz) (micorvolts/meter) (meters) 30~88 100 3 88~216 150 3 216~960 200 3 Above 960 500 3 Receiver Parameter Setting Attenuation Auto Start ~ Stop Frequency 9kHz~90kHz / RB 200Hz for PK & AV Start ~ Stop Frequency 90kHz~110kHz / RB 200Hz for QP Start ~ Stop Frequency 110kHz~490kHz / RB 200Hz for PK & AV Start ~ Stop Frequency 490kHz~30MHz / RB 9kHz for QP Start ~ Stop Frequency 30MHz~1000MHz / RB 120kHz for QP 4.2 TEST PROCEDURE a. The test is performed in a 3m Semi-Anechoic Chamber; the antenna factor, cable loss and so on of the site (factors) is calculated to correct the reading. The EUT is placed on a 0.8m high insulating Turn Table, and keeps 3m away from the Test Antenna, which is mounted on a variable-height antenna master tower. For the test Antenna b. In the frequency range of 9KHz to 30MHz, magnetic field is measured with Loop Test Antenna. The Test Antenna is positioned with its plane vertical at 1m distance from the EUT. The center of the Loop Test Antenna is 1m above the ground. During the measurement the Loop Test Antenna rotates about its vertical axis for maximum response at each azimuth about the EUT. c. In the frequency range above 30MHz, Bi-Log Test Antenna (30MHz to 1GHz) used. Test Antenna is 3m away from the EUT. Test Antenna height is varied from 1m to 4m above the ground to determine the maximum value of the field strength. The emission levels at both horizontal and vertical polarizations should be tested. f. The initial step in collecting conducted emission data is a spectrum analyzer peak detector mode pre-scanning the measurement frequency range. Significant peaks are then marked and then Quasi Peak detector mode re-measured. g. If the Peak Mode measured value compliance with and lower than Quasi Peak Mode Limit, the EUT shall be deemed to meet QP Limits and then no additional QP Mode measurement performed. h. For the actual test configuration, please refer to the related Item –EUT Test Photos. NOTE: Both horizontal and vertical antenna polarities were tested and performed pretest to three orthogonal axis. The worst case emissions were reported

D I uma» \—— Page 15 of 24 Report No.: STS1606212F01 4.3 TEST SETUP (A) Radiated Emission Test—Up Frequency Below 3OMHz Loop Antenna EUT <—_—— Sm _2 mm |_ y J Spectrum Ground Plane Coaxial Cable Analyzer (B) Radiated Emission Test—Up Frequency 3OMHz~1GHz i iss la— 3m —» Turntable i 1 4 \ EuT m t to 4m ~~~~&0°~ Spectrum ID Bm C / Analyzer Ground Plane — Coaxial Cable 4.4 EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 2.3 Unless otherwise a special operating condition is specified in the follows during the testing. 1/F., Building 8, Zhuoke Science Park, No.190,Chongging Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong,China Shenzhen STS Test Services Co., Ltd. Tel: 0755—36886288 Fax:0755—36886277 Http//www.stsapp.com E—mail:sts@stsapp.com

P \— Page 16 of 24 Report No.: STS1606212F01 4.5 TEST RESULTS (Radiated Emission<30MHz (9KHz—30MHz, H—field)) Temperature: 20 °C Relative Humidtity: 48% Pressure: 1010 hPa Test Voltage : DC 3V Test Mode : Mode 1 Polarization : —— Not: Horizontal level have a test this is the worst. Freq. Reading Limit Margin State (MHz) (dBuV/m) (dBuV/m) (dB) PIF 13.553 62.01 90.47 —28.46 PASS 13.560 97.96 124 —26.04 PASS 13.574 65.12 90.47 —25.35 PASS 13.585 65.36 90.47 —25.11 PASS 13.724 65.38 80.51 ~15.13 PASS Note:Distance extrapolation factor =40 log (specific distance/test distance)(dB); Limit line = specific limits(dBuv) + distance extrapolation factor. 1/F., Building 8, Zhuoke Science Park, No.190,Chongging Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong,China Shenzhen STS Test Services CO., Ltd. Tel: 0755—36886288 —Fax:.0755—36886277 Httpy//www.stsapp.com E—mail:sts@stsapp.com

P / Ecten CecGe cce Between 30—1000MHz Temperature: 26 °C Relative Humidity: 154% Pressure: 1010hPa Phase: Horizontal Test Voltage: DC 3V Test Mode: Mode 1 Frequency Reading Correct Result Limit Margin Remark (MHz) (dBuV) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) 35.3750 31.35 —13.94 17.41 40.00 —22.59 aP 474917 39.16 —20.19 18.97 40.00 —21.03 aP 114.9168 32.33 —18.02 14.31 43.50 —29.19 aP 179.3863 32.39 —19.43 12.96 43.50 —30.54 aP 410.3824 27.78 —11.06 16.72 46.00 —29.28 aP 675.2080 30.14 —5.87 24.27 46.00 —21.73 aP Remark: 1. Margin = Result (Result =Reading + Factor )—Limit 80.0 dBu¥/m Limit1: — Margin: — 40 0.0 30.000 40 50 60 70 80 (MHz) 300 400 500 600 700 1000.000 1/F., Building 8, Zhuoke Science Park, No.190,Chongging Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong,China Shenzhen STS Test Services CO., Ltd Tel: 0755—36886288 Fax:.0755—36886277. Http//wwwstsapp.com E—mail:sts@stsapp.com

P \— Page 18 of 24 Report No.: STS1606212F01 Temperature: 26 °C Relative Humidity: 154% Pressure: 1010hPa Phase: Vertical Test Voltage: DC 3V Test Mode: Mode 1 Frequency Reading Correct Result Limit Margin Remark (MHz) (dBuV) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) 34.6385 34.39 —13.57 20.82 40.00 —19.18 aP 49.1865 37.14 —21.06 16.08 40.00 —23.92 aP 114.5146 32.64 —18.05 14.59 43.50 —28.91 aP 259.2337 29.65 ~15.15 14.50 46.00 —31.50 aP 562.6624 27.84 —6.57 21.27 46.00 —24.73 aP 779.6068 27.01 —3.11 23.90 46.00 —22.10 aP Remark: 1. Margin = Result (Result =Reading + Factor )—Limit 80.0 dBu¥/m Limit1: — Margin: — a0 0.0 30.000 40 50 60 70 80 (MHz) 300 400 500 600 700 1000.000 1/F., Building 8, Zhuoke Science Park, No.190,Chongging Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong,China Shenzhen STS Test Services CO., Ltd Tel: 0755—36886288 Fax:.0755—36886277. Http//wwwstsapp.com E—mail:sts@stsapp.com

Page 19 of 24 Report No.: STS1606212F01 5. FREQUENCY TOLERANCE 5.1 REQUIREMENT According to FCC section 15.225, the devices operating in the 13.553-13.567 MHz shall maintain the carrier frequency within 0.01% of the operating frequency over the temperature variation of -20°C to +50°C using an environmental chamber. The primary supply voltage is varied from 85% to 115% of the voltage normally at the input to the device or at the power supply terminals if cables are not normally supplied. 5.2 TEST PROCEDURE According to FCC section 15.225(e),The frequency tolerance of the carrier signal shall be maintained within ±0.01% of the operating frequency over a temperature variation of −20 degrees to + 50 degrees C at normal supply voltage, and for a variation in the primary supply voltage from 85% to 115% of the rated supply voltage at a temperature of 20 degrees C. For battery operated equipment, the equipment tests shall be performed using a new battery. 5.3 TEST SETUP The EUT which is powered by the Battery, is coupled to the Spectrum Analyzer; the RF load attached to the EUT antenna terminal is 50Ohm; the path loss as the factor is calibrated to correct the reading. 5.4 EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 2.3 Unless otherwise a special operating condition is specified in the follows during the testing.

P \— Page 20 of 24 Report No.: STS1606212F01 5.5 TEST RESULTS Temperature : 25 °C Relative Humidity : |50% Pressure : 1012 hPa Test Voltage : DC 3V Test Mode : TX Mode 13.56MHz Test Conditions Power Temperature Frequency(Hz) Deviation(%) Limit Verdict (VDC) (°C) +20°C(Ref) 13559516 —0.008357 £0.01% —20 13559421 —0.00427 £0.01% —10 13559483 —0.00381 £0.01% 0 13559410 —0.00435 £0.01% 10 13559358 —0.00473 +0.01% 3 *—| PaSS 20 13559454 —0.00403 £0.01% 25 13560541 0.00399 £0.01% 30 13559452 —0.00404 £0.01% 40 13559448 —0.00407 £0.01% 50 13559500 —0.00369 £0.01% 1/F., Building B, Zhuoke Science Park, No.190,Chongging Road, Fuyong Street, Bac‘an Distrct, Shenzhen, Guangdong,China Shenzhen STS Test Services CO., Ltd Tel: 0755—36886288 Fax:.0755—36886277. Http//wwwstsapp.com E—mail:sts@stsapp.com

Page 21 of 24 Report No.: STS1606212F01 6. 20DB BANDWIDTH 6.1 APPLIED PROCEDURES / LIMIT According to FCC section 15.215(c), the 20dB bandwidth should be contained within the frequency band designated in the rule section under which the EUT is operated, it was measured with a spectrum analyzer connected the EUT while the EUT is operating in transmission mode. 6.2 TEST PROCEDURE Intentional radiators operating under the alternative provisions to the general emission limits, as contained in §13.553-13.567 MHz and in subpart E of this part, must be designed to ensure that the 20 dB bandwidth of the emission, or whatever bandwidth may otherwise be specified in the specific rule section under which the equipment operates, is contained within the frequency band designated in the rule section under which the equipment is operated. In the case of intentional radiators operating under the provisions of subpart E, the emission bandwidth may span across multiple contiguous frequency bands identified in that subpart. The requirement to contain the designated bandwidth of the emission within the specified frequency band includes the effects from frequency sweeping, frequency hopping and other modulation techniques that may be employed as well as the frequency stability of the transmitter over expected variations in temperature and supply voltage. If a frequency stability is not specified in the regulations, it is recommended that the fundamental emission be kept within at least the central 80% of the permitted band in order to minimize the possibility of out-of-band operation. 1. Set RBW = 1 kHz. 2. Set the video 2W WL LCD Keypad, 915width (VBW) ≥ 3 RBW. 3. Detector = Peak. 4. Trace mode = max hold. 5. Sweep = auto couple. 6. Allow the trace to stabilize. 7.Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 d B relative to the maximum level measured in the fundamental emission. 6.3 TEST SETUP 6.4 EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 2.3 Unless otherwise a special operating condition is specified in the follows during the testing.

) <25 mu» I mmme 6.5 TEST RESULTS Temperature : 25 °C Relative Humidity : [60% Pressure : 1012 hPa Test Voltage : DC 3V Test Mode : TX Mode 13.56MHz Centre Measurement Frequency 200B Bandwidth 99% Bandwidth (KHz) (KHz) Frequency Range (MHz) 13.56MHz 10.474 9.3129 13.553—13.567 Aiten 10 dB EnEuMUNCUH ud Cns Occupied Bandwidth 9.3129 kHz 1/., Building 8, Zhuoke Science Park, No.190,Chongging Road, Fuyong Street, Bac‘anDistrict, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: 0755—36886288 Fax:0755—36886277 Http//wwwstsapp.com E—mail:sts@stsapp.com

Page 23 of 24 Report No.: STS1606212F01 7. ANTENNA REQUIREMENT 7.1 STANDARD REQUIREMENT 15.203 requirement: For intentional device, according to 15.203: an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 7.2 EUT ANTENNA The EUT antenna is integral Antenna. It comply with the standard requirement. The EUT antenna is Spring Antenna. It comply with the standard requirement.


Document Created: 2016-08-02 22:43:17
Document Modified: 2016-08-02 22:43:17
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC