Test Report

FCC ID: JE4RPKELP

Test Report

Download: PDF
FCCID_3888126

S T RADIO TEST REPORT Report No:STS1805200W01 S Issued for Risco Ltd. 14 Hachoma Street,Rishon Lezion,75655,Israel L Product Name: Brand Name: Elegant Keypad, White W/Prox RISCO A Model Name: Series Model: RPKELP N/A B FCC ID: Test Standard: JE4RPKELP FCC Part 15.225 Any reproduction of this document must be done in full. No single part of this document may be reproduced without permission from STS, All Test Data Presented in this report is only applicable to presented Test sample. Shenzhen STS Test Services Co., Ltd. 1/F., Building B, Zhuoke Science Park, No.190, Chongqing Road, Fuyong Street, Bao’an District, Shenzhen, Guangdong, China TEL: +86-755 3688 6288 FAX: +86-755 3688 6277 E-mail:sts@stsapp.com

Page 2 of 27 Report No.: STS1805200W01 TEST REPORT CERTIFICATION Applicant’s name ................. : Risco Ltd. Address .................................. : 14 Hachoma Street,Rishon Lezion,75655,Israel Manufacture's Name ............ : RISCO LTD. Address .................................. : Sderot Yahalom 6 Kiryat Gat, Israel Product description Product Name ........................ : Elegant Keypad, White W/Prox Brand Name ......................... : RISCO Model Name........................... : RPKELP Series Model .......................... : N/A Test Standards ..................... : FCC Part15.225 Test procedure ...............................ANSI : C63.10: 2013,ANSI C63.4: 2014 This device described above has been tested by STS, the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of STS, thidocument only be altered or revised by STS, personal only, and shall be noted in the revision of the document. Date of Test ............................................: Date (s) of performance of tests..............: 22 May 2018~30 May 2018 Date of Issue ...........................................: 01 Jun. 2018 Test Result ...............................................: Pass Testing Engineer : ( Chris chen ) Technical Manager : ( Sean she ) Authorized Signatory : (Vita Li)

Page 3 of 27 Report No.: STS1805200W01 TABLE OF CONTENTS Page 1. SUMMARY OF TEST RESULTS 5 1.1 TEST FACTORY 5 1.2 MEASUREMENT UNCERTAINTY 5 2. GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF EUT 6 2.2 DESCRIPTION OF TEST MODES 7 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 7 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 8 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 9 3. EMC EMISSION TEST 10 3.1 CONDUCTED EMISSION MEASUREMENT 10 3.2 TEST PROCEDURE 11 3.3 TEST SETUP 11 3.4 EUT OPERATING CONDITIONS 11 3.5 TEST RESULTS 12 4. RADIATED EMISSION MEASUREMENT 14 4.1 RADIATED EMISSION LIMITS 14 4.2 TEST PROCEDURE 15 4.3 TEST SETUP 16 4.4 EUT OPERATING CONDITIONS 16 5. FREQUENCY TOLERANCE 21 5.1 REQUIREMENT 21 5.2 TEST PROCEDURE 21 5.3 TEST SETUP 21 5.4 EUT OPERATION CONDITIONS 21 5.5 TEST RESULTS 22 6. 20DB BANDWIDTH 23 6.1 APPLIED PROCEDURES / LIMIT 23 6.2 TEST PROCEDURE 23 6.3 TEST SETUP 23 6.4 EUT OPERATION CONDITIONS 23 6.5 TEST RESULTS 24

Page 4 of 27 Report No.: STS1805200W01 TABLE OF CONTENTS Page 7. ANTENNA REQUIREMENT 25 7.1 STANDARD REQUIREMENT 25 7.2 EUT ANTENNA 25 APPENDIX 1- PHOTOS OF TEST SETUP 26

Page 5 of 27 Report No.: STS1805200W01 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 15.225 , Subpart C Standard Test Item Judgment Remark Section 15.207 Conducted Emission PASS -- 15.209 Radiated Emission PASS -- 15.225(a)(b)(c)(d) 15.225(e) Frequency Tolerance PASS -- 15.203 Antenna Requirement PASS -- 15.215 20dB Bandwidth PASS -- NOTE: (1)” N/A” denotes test is not applicable in this Test Report (2) All tests are according to ANSI C63.4-2014 and ANSI C63.10-2013 1.1 TEST FACTORY Shenzhen STS Test Services Co., Ltd. 1/F., Building B, Zhuoke Science Park, No.190, Chongqing Road, Fuyong Street, Bao’an District, Shenzhen, Guangdong, China CNAS Registration No.: L7649; FCC Registration No.: 625569 IC Registration No.: 12108A; A2LA Certificate No.: 4338.01; 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission (9KHz-150KHz) ±2.88dB 2 Conducted Emission (150KHz-30MHz) ±2.67dB 3 RF power,conducted ±0.71dB 4 Spurious emissions,conducted ±0.63dB 5 All emissions,radiated (9KHz-30MHz) ±3.02dB 6 All emissions,radiated (30MHz-200MHz) ±3.80dB 7 All emissions,radiated (200MHz-1000MHz) ±3.97dB

Page 6 of 27 Report No.: STS1805200W01 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Product Name Elegant Keypad, White W/Prox Trade Name RISCO Model Name RPKELP Serial Model N/A Model Difference N/A The EUT is a Elegant Keypad, White W/Prox Operation Frequency: 13.56MHz Product Description Modulation Type: ASK Antenna Designation: Please see Note 3. Antenna Gain (dBi) 0 dbi Power Rating DC 12V Connecting I/O Port(s) Please refer to the User's Manual Model Description PCB HW Rev S/W Rev Elegant 1PC512KELKEYB A V1.07 RPKELP Keypad,White W/Prox 1PC512KELM00C A V1.07 Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. 2. Table for filed Antenna Ant. Brand Model Name Antenna Type Connector Gain (dBi) NOTE A RISCO RPKELP Printed Antenna N/A 0 ANT

Page 7 of 27 Report No.: STS1805200W01 2.2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 TX Mode For Conducted Test Final Test Mode Description Mode 1 TX Mode For Radiated Emission Final Test Mode Description Mode 1 TX Mode Note: (1) The measurements are performed at the highest, middle, lowest available channels. (2) The measurements are performed at all Bit Rate of Transmitter, the worst data was reported (3) We have be tested for all avaiable U.S. voltage and frequencies(For 120V,50/60Hz) for which the device is capable of operation. 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED

Page 8 of 27 Report No.: STS1805200W01 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Mfr/Brand Model/Type No. Series No. Note Elegant Keypad, E-1 RISCO RPKELP N/A N/A White W/Prox Item Shielded Type Ferrite Core Length Note E-1 NO NO >30m N/A Note: (1)The support equipment was authorized by Declaration of Confirmation. (2)For detachable type I/O cable should be specified the length in cm in『Length』column.

Page 9 of 27 Report No.: STS1805200W01 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS Radiation Test equipment Kind of Equipment Manufacturer Type No. Serial No. Last calibration Calibrated until EMI Test Receiver R&S ESCI 102086 2017.10.15 2018.10.14 Bilog Antenna TESEQ CBL6111D 34678 2017.11.02 2018.11.01 BBHA 9120D Horn Antenna Schwarzbeck 9120D-1343 2017.10.27 2018.10.26 (1201) Passive Loop ZHNAN ZN3090C 16035 2018.03.11 2019.03.10 (9K--30MHz) Pre-mplifier EM EM330 60538 2018.03.11 2019.03.10 (0.1M-3GHz) PreAmplifier Agilent 8449B 60538 2017.10.15 2018.10.14 USB RF power DARE RPR3006W 15I00041SNO03 2017.10.15 2018.10.14 sensor Semi-anechoic Changling 966 N/A 2017.10.15 2018.10.14 chamber Conduction Test equipment Kind of Equipment Manufacturer Type No. Serial No. Last calibration Calibrated until Test Receiver R&S ESCI 101427 2017.10.15 2018.10.14 LISN R&S ENV216 101242 2017.10.15 2018.10.14 conduction Cable EM C01 N/A 2018.03.11 2019.03.10 Temperature & Mieo HH660 N/A 2017.10.15 2018.10.14 Humitidy

Page 10 of 27 Report No.: STS1805200W01 3. EMC EMISSION TEST 3.1 CONDUCTED EMISSION MEASUREMENT 3.1.1 POWER LINE CONDUCTED EMISSION LIMITS Operating frequency band. In case the emission fall within the restricted band specified on Part 15. 207(a) limit in the table below has to be followed. Class B (dBuV) FREQUENCY (MHz) Standard Quasi-peak Average 0.15 -0.5 66 - 56 * 56 - 46 * CISPR 0.50 -5.0 56.00 46.00 CISPR 5.0 -30.0 60.00 50.00 CISPR 0.15 -0.5 66 - 56 * 56 - 46 * FCC 0.50 -5.0 56.00 46.00 FCC 5.0 -30.0 60.00 50.00 FCC Note: (1) The tighter limit applies at the band edges. (2) The limit of " * " marked band means the limitation decreases linearly with the logarithm of the frequency in the range. The following table is the setting of the receiver Receiver Parameters Setting Attenuation 10 dB Start Frequency 0.15 MHz Stop Frequency 30 MHz IF Bandwidth 9 kHz

Page 11 of 27 Report No.: STS1805200W01 3.2 TEST PROCEDURE a.The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b.Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. c.I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d.LISN at least 80 cm from nearest part of EUT chassis. e.For the actual test configuration, please refer to the related Item –EUT Test Photos. 3.3 TEST SETUP Vertical Reference Ground Plane Test Receiver EUT 40cm 80cm LISN Horizontal Reference Ground Plane Note: 1.Support units were connected to second LISN. 2.Both of LISNs (AMN) are 80 cm from EUT and at least 80 cm from other units and other metal planes support. units. 3.4 EUT OPERATING CONDITIONS The EUT was configured for testing in a typical fashion (as a customer would normally use it). The EUT has been programmed to continuously transmit during test. This operating condition was tested and used to collect the included data.

P aas. I tams \— Page 12 of 27 Report No.: STS1805200W01 3.5 TEST RESULTS Temperature: 26 °C Relative Humidity: 63% Test Voltage: AC 120V/60H2z Phase: L Test Mode: Mode 1 Frequency Reading Correct Resutt Limit Margin Remark (MHz) (dBuV) Factor(dB) (dBuV) (dBuV) (dB) 0.1500 52.09 9.79 61.88 66.00 412 aP 0.1500 26.00 9.79 35.79 56.00 —20.21 AVG 0.1820 49.31 9.78 59.09 64.39 —5.30 aP 0.1820 22.98 9.78 32.76 54.39 —21.63 AVG 0.4620 29.21 10.03 39.24 56.66 —17 42 aP 0.4620 19.35 10.03 29.38 46.66 —17.28 AVG 1.4340 17. 43 9.79 27.22 56.00 —28.78 aP 1.4340 7.00 9.79 16.79 46.00 —29.21 AVG 6.2860 22.70 9.87 32.57 60.00 —27 48 aP 6.2860 11.08 9.87 20.95 50.00 —29.05 AVG 13.5620 37.26 10.22 47 .48 60.00 —12.52 aP 13.5620 36.54 10.22 46.76 50.00 —3.24 AVG Remark: 1. All readings are Quasi—Peak and Average values. 2. Margin = Result (Result =Reading + Factor )—Limit 100.0 dBu¥ Limitt: — Limit2: — oT 5o 7 peak AvG 0.0 0.150 0.5 (MHz) 5 30.000 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: + 86—785 3688 6288 Fax+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com

P mau» I umm 3 Temperature: 26°C Relative Humidity: 63% Test Voltage: AC 120V/60H2z Phase: N Test Mode: Mode 1 Frequency Reading Correct Resutt Limit Margin Remark (MHz) (dBuV) Factor(dB) (dBuV) (dBuV) (dB) 0.1500 52.78 9.79 62.57 66.00 —3.48 aP 0.1500 25.11 9.79 34.90 56.00 —21.10 AVG 0.1860 48.13 9.78 57.91 64.21 —6.30 aP 0.1860 20.99 9.78 30.77 54.21 —23. 44 AVG 0.4620 26.04 10.03 36.07 56.66 —20.59 aP 0.4620 17.75 10.03 27.78 46.66 —18.88 AVG 1.7340 19.22 9.79 29.01 56.00 —26.99 aP 1.7340 5.99 9.79 15.78 46.00 —30.22 AVG 5.0340 19.24 9.85 29.09 60.00 —30.91 aP 5.0340 6.84 9.85 16.69 50.00 —33.31 AVG 13.5620 35.95 10.22 46.17 60.00 —13.83 aP 13.5620 35.14 10.22 45.36 50.00 ~4.64 AVG Remark: 1. All readings are Quasi—Peak and Average values. 2. Margin = Result (Result =Reading + Factor )—Limit 100.0 dBu¥ Limi1: — Limit2: — \ I— 50 peak y AvG 0.0 0.150 0.5 [MHz] 5 30.000 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: + 86—785 3688 6288 Fax+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com

) \— Page 14 of 27 Report No.: STS1805200W01 4. RADIATED EMISSION MEASUREMENT 4.1 RADIATED EMISSION LIMITS (a) The field strength of any emissions within the band 13.553—13.567 MHz shall not exceed 15,848 microvolts/meter at 30 meters. (b) Within the bands 13.410—13.553 MHz and 13.567—13.710 MHz, the field strength of any emissions shall not exceed 334 microvolts/meter at 30 meters. (c) Within the bands 13.110—13.410 MHz and 13.710—14.010 MHz the field strength of any emissions shall not exceed 106 microvolts/meter at 30 meters. (d) The field strength of any emissions appearing outside of the 13.110—14.010 MHz band shall not exceed the general radiated emission limits in §15.209. (Radiated Emission <30MHz (9KHz—30MHz, H—field) According to FCC section 15.225, for <30MHz, Radiated emissions were measured according to ANSIC63.4. The EUT was set to transmit at the highest output power. The EUT was set 30 meter away from the measuring antenna. The loop antenna was positioned 1 meter above the ground from the center of the loop. The measuring bandwidth was set to 10KHz. (Note: During testing the receive antenna was rotated about its axis to maximize the emission from the EUT) There was no detected Restricted bands and Radiated suprious emission below 3OMHz. The 3O0m limit was converted to 3m Limit using square factor(x) as it was found by measurements as follows; 3 m Limit(dBuV/m) = 20log(X)+4010g(30/3)= 20log(15,848)+40l0g(30/3) =124dBuV y tr—tect—a 3 m Limit(dBuV/m) = 20log(X)+4010g(30/3)= 20l0g(334)+4010g(30/3) =90.47dBuV 3 m Limit(dBuV/m) = 20log(X)+40l0g(30/3)= 20log(106)+40l0g(30/3) =80.506dBuV 3 m Limit(dBuV/m) = 20log(X)+4010g(30/3)= 20l0g(30)+4010g(30/3) =69.54dBuV Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: LIMITS OF RADIATED EMISSION MEASUREMENT (Frequency Range 9kHz—1000MHz) Field Strength@30m Field Strength@3m Frequency range (MHz) pV/m dBuV/m dBuV/m Below 13.110 30 29.5 69.5 13.110 ~13.410 106 40.5 80.5 13.410 ~ 13.553 334 50.5 90.5 13.553 ~18.567 15.848 84 105.4 13.567 ~13.710 334 50.5 90.5 13.710 ~14.010 106 40.5 80.5 Above 14.010 30 29.5 69.5 NOTE: a) Field Strength (dBuV/m) = 20*log[Field Strength (uV/m)]. b) In the emission tables above, the tighter limit applies at the Band edge. Radiated Emission >30MHz (30MHz—1GHz, E—field) According to FCC section 15.205, the field strength of radiated emissions from intentiona radiators at a distance of 3 meters shall not exceed the following values: 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services CO. Ltd Tel: + 86—785 3688 6288 Fax+ 86—755 3688 6277 Http://www.stsapp.com E—mail: sts@stsapp.com

Page 15 of 27 Report No.: STS1805200W01 Frequencies Field Strength Measurement Distance (MHz) (micorvolts/meter) (meters) 30~88 100 3 88~216 150 3 216~960 200 3 Above 960 500 3 Receiver Parameter Setting Attenuation Auto Start ~ Stop Frequency 9kHz~90kHz / RB 200Hz for PK & AV Start ~ Stop Frequency 90kHz~110kHz / RB 200Hz for QP Start ~ Stop Frequency 110kHz~490kHz / RB 200Hz for PK & AV Start ~ Stop Frequency 490kHz~30MHz / RB 9kHz for QP Start ~ Stop Frequency 30MHz~1000MHz / RB 120kHz for QP 4.2 TEST PROCEDURE a. The test is performed in a 3m Semi-Anechoic Chamber; the antenna factor, cable loss and so on of the site (factors) is calculated to correct the reading. The EUT is placed on a 0.8m high insulating Turn Table, and keeps 3m away from the Test Antenna, which is mounted on a variable-height antenna master tower. For the test Antenna b. In the frequency range of 9KHz to 30MHz, magnetic field is measured with Loop Test Antenna. The Test Antenna is positioned with its plane vertical at 1m distance from the EUT. The center of the Loop Test Antenna is 1m above the ground. During the measurement the Loop Test Antenna rotates about its vertical axis for maximum response at each azimuth about the EUT. c. In the frequency range above 30MHz, Bi-Log Test Antenna (30MHz to 1GHz) used. Test Antenna is 3m away from the EUT. Test Antenna height is varied from 1m to 4m above the ground to determine the maximum value of the field strength. The emission levels at both horizontal and vertical polarizations should be tested. f. The initial step in collecting conducted emission data is a spectrum analyzer peak detector mode pre-scanning the measurement frequency range. Significant peaks are then marked and then Quasi Peak detector mode re-measured. g. If the Peak Mode measured value compliance with and lower than Quasi Peak Mode Limit, the EUT shall be deemed to meet QP Limits and then no additional QP Mode measurement performed. h. For the actual test configuration, please refer to the related Item –EUT Test Photos. NOTE: Both horizontal and vertical antenna polarities were tested and performed pretest to three orthogonal axis. The worst case emissions were reported

D I uy \—— ETtE0 e TttPereccprang 4.3 TEST SETUP (A) Radiated Emission Test—Up Frequency Below 30OMHz Loop Antenna EUT <—— 3m ———» CZ—IJ 4‘ 0.8m n sSpectrum Ground Plane J Coaxial Cable Analyzer Radiated Emission Test—Up Frequency 30MHz~1GHz m & w Turntable \ EuT 1m to 4m Dollccel Spectrum ID 8m L / Analyzer Ground Plane —I Coaxial Cable 4.4 EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 2.3 Unless otherwise a special operating condition is specified in the follows during the testing. 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: + 86—785 3688 6288 Fax+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com

Page 17 of 27 Report No.: STS1805200W01 4.5 FIELD STRENGTH CALCULATION The field strength is calculated by adding the Antenna Factor and Cable Factor and subtracting the Amplifier Gain and Duty Cycle Correction Factor (if any) from the measured reading. The basic equation with a sample calculation is as follows: FS = RA + AF + CL - AG Where FS = Field Strength CL = Cable Attenuation Factor (Cable Loss) RA = Reading Amplitude AG = Amplifier Gain AF = Antenna Factor For example Frequency FS RA AF CL AG Factor (MHz) (dBμV/m) (dBμV/m) (dB) (dB) (dB) (dB) 300 40 58.1 12.2 1.6 31.9 -18.1 Factor=AF+CL-AG

P \— Page 18 of 27 Report No.: STS1805200W01 4.6 TEST RESULTS (Radiated Emission<30MHz (9KHz—30MHz, H—field)) Temperature: 24 °CC Relative Humidtity: 60% Test Voltage: DC 12V Polarization: —— Test Mode: Mode 1 Not: Horizontal level have a test this is the worst. Freq. Reading Limit Margin Detector State (MHz) (dBuV/m) (dBuV/m) (dB) (PK/QP/AV) P/F 12.12 59.06 69.54 —10.48 aP PASS 13.33 60.61 80.51 —19.9 aP PASS 13.45 60.29 90.47 —30.18 aP PASS 13.56 96.67 105.4 —8.73 aP PASS 13.67 61.92 90.47 —28.55 aP PASS 13.89 61.15 80.51 —19.36 aP PASS 15.21 61.06 69.54 —8.48 aP PASS Note: Anarfiad = 4?'??_-'I:j'.k1'llz (1) d, bns PSimn * 4Smzx —mlog[fl]—zmog im dmfl! naurfild (2) Where FSimit is the calculation of field strength at the limit distance, expressed in dBu\V/m FSmax is the measured field strength, expressed in dBuV/m Crnear ied is the NZT distance Uneasure is the distance of the measurement point from the EUT Climit is the reference limit distance. Shenshen STS TestGemmices 60. H. eenon remntmennionnenamnamen amageoo *

P \— Page 19 of 27 Report No.: STS1805200W01 Between 30—1000MHz Temperature: 25.7 °C Relative Humidity: (63% Test Voltage: DC 12V Phase: Horizontal Test Mode: Mode 1 Frequency Reading Correct Result Limit Margin Remark (MHz) (dBuV) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) 46.8303 41.62 —19.85 21.77 40.00 —18.23 aP 68.6310 38.83 —24.14 14.69 40.00 —25.31 aP 121.9755 34.28 —17.66 16.62 43.50 —26.88 aP 176.2686 36.47 —19.41 17.06 43.50 —26.44 aP 462.3455 36.26 —10.62 25.64 46.00 —20.36 aP 638.3686 33.37 —6.36 27.01 46.00 —18.99 aP Remark: 1. Margin = Result (Result =Reading + Factor )—Limit 80.0 dBu¥/m Limit1: — Margin: _ 40 0.0 20.000 40 50 60 70 80 (MHz] 2300 400 500 600 700 1000.000 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: + 86—785 3688 6288 Faxc+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com

P <4 Temperature: 25.7 °C Relative Humidity: (63% Test Voltage: DC 12V Phase: Vertical Test Mode: Mode 1 Frequency Reading Correct Result Limit Margin Remark (MHz) (dBuV) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) 43.8120 44.31 —18.29 26.02 40.00 —13.98 aP 67.6751 49.00 —24.16 24.84 40.00 ~15.16 aP 121.9755 38.37 —17.66 20.71 43.50 —22.79 aP 176.2686 38.70 —19.41 19.29 43.50 —24.21 aP 460.7271 33.88 —10.11 23.77 46.00 —22.23 aP 968.9338 28.04 —0.13 27.91 54.00 —26.09 aP Remark: 1. Margin = Result (Result =Reading + Factor )—Limit 80.0 dBu¥/m Limit1: — Margin: —— 20.000 40 50 so 70 80 [MHz] 300 400 500 600 700 1000.000 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: + 86—785 3688 6288 Faxc+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com

Page 21 of 27 Report No.: STS1805200W01 5. FREQUENCY TOLERANCE 5.1 REQUIREMENT According to FCC section 15.225, the devices operating in the 13.553-13.567 MHz shall maintain the carrier frequency within 0.01% of the operating frequency over the temperature variation of -20°C to +50°C using an environmental chamber. The primary supply voltage is varied from 85% to 115% of the voltage normally at the input to the device or at the power supply terminals if cables are not normally supplied. 5.2 TEST PROCEDURE According to FCC section 15.225(e),The frequency tolerance of the carrier signal shall be maintained within ±0.01% of the operating frequency over a temperature variation of −20 degrees to + 50 degrees C at normal supply voltage, and for a variation in the primary supply voltage from 85% to 115% of the rated supply voltage at a temperature of 20 degrees C. For battery operated equipment, the equipment tests shall be performed using a new battery. 5.3 TEST SETUP The EUT which is powered by the Battery, is coupled to the Spectrum Analyzer; the RF load attached to the EUT antenna terminal is 50Ohm; the path loss as the factor is calibrated to correct the reading. 5.4 EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 2.3 Unless otherwise a special operating condition is specified in the follows during the testing.

P <ommm <m [d ' smm \— Page 22 of 27 Report No.: STS1805200W01 5.5 TEST RESULTS Temperature: 25 °C Relative Humidity: 150% Test Voltage: DC 12V Test Mode: TX Mode 13.56MHz Test Conditions VOLTAGE(%) Power Temperature Frequency(Hz) Deviation(%) Limit Verdict (VDC) (°C) 100 +20°C(Ref) 13560754 0.00556 £0.01% 100 —20 13560754 0.00556 £0.01% 100 —10 13560752 0.00555 £0.01% 100 0 13560750 0.005583 £0.01% 100 10 13560751 0.00554 £0.01% 100 12 20 13560754 0.00556 £0.01% pass 100 25 13560752 0.00555 £0.01% 100 30 13560754 0.00556 £0.01% 100 40 13560751 0.00554 £0.01% 100 50 13560754 0.00556 £0.01% 85 10.2 20 13560753 0.00555 £0.01% 115 13.8 20 13560753 0.00555 £0.01% Shenzhen STS Test Services Co., Ltd. hocnsesrse esneote:feonterenoitniecls.islanakemamenmmandenmaten_—_

Page 23 of 27 Report No.: STS1805200W01 6. 20DB BANDWIDTH 6.1 APPLIED PROCEDURES / LIMIT According to FCC section 15.215(c), the 20dB bandwidth should be contained within the frequency band designated in the rule section under which the EUT is operated, it was measured with a spectrum analyzer connected the EUT while the EUT is operating in transmission mode. 6.2 TEST PROCEDURE Intentional radiators operating under the alternative provisions to the general emission limits, as contained in §13.553-13.567 MHz and in subpart E of this part, must be designed to ensure that the 20 dB bandwidth of the emission, or whatever bandwidth may otherwise be specified in the specific rule section under which the equipment operates, is contained within the frequency band designated in the rule section under which the equipment is operated. In the case of intentional radiators operating under the provisions of subpart E, the emission bandwidth may span across multiple contiguous frequency bands identified in that subpart. The requirement to contain the designated bandwidth of the emission within the specified frequency band includes the effects from frequency sweeping, frequency hopping and other modulation techniques that may be employed as well as the frequency stability of the transmitter over expected variations in temperature and supply voltage. If a frequency stability is not specified in the regulations, it is recommended that the fundamental emission be kept within at least the central 80% of the permitted band in order to minimize the possibility of out-of-band operation. 1. Set RBW = 1 kHz. 2. Set the video Mobile Phonewidth (VBW) ≥ 3 RBW. 3. Detector = Peak. 4. Trace mode = max hold. 5. Sweep = auto couple. 6. Allow the trace to stabilize. 7.Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 d B relative to the maximum level measured in the fundamental emission. 6.3 TEST SETUP 6.4 EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 2.3 Unless otherwise a special operating condition is specified in the follows during the testing.

3 \—» Ce es Report No.: STS1805200W01 6.5 TEST RESULTS Temperature: 25 °C Relative Humidity: |60% Test Voltage: DC 12V Test Mode: TX Mode 13.56MH Centre Measurement Frequency 20dB(i?_|nZo)|width 99% (I?(afizd)width Frequency Range (MHz) 13.56MHz 2.641 2.265 13.553—13.567 muicuauro Jozossy m 2ore Genter Freg: 19560000 Mz Radio Std: None TraceiDetector ; Trig:Free Run & #atten: 30 dB AvglHld> 10rt0 #iEGainow Radio Device: BTS 0 dBtdiv Ref 0.00 dBm og 100 z0 zo o o o 700 o o 13.56 MHz Span 50 BW 1 kHz AVBW 1 kHz Sweep 77.87 Occupied Bandwidth 2.265 kHz Average Transmit Freq Error —86 Hz OBW Power 99.00 % Man x dB Bandwidth 2.641 kHz x dB —20.00 dB 1/F., Building B, Zhuoke Science Park, No.190, Chongging Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: +86—755 3688 6288 Fax:+86—755 3688 6277 Hitp{//www.stsapp.com E—mail: sts@stsapp.com

Page 25 of 27 Report No.: STS1805200W01 7. ANTENNA REQUIREMENT 7.1 STANDARD REQUIREMENT 15.203 requirement: For intentional device, according to 15.203: an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 7.2 EUT ANTENNA The EUT antenna is Printed Antenna. It comply with the standard requirement.

Page 26 of 27 Report No.: STS1805200W01 APPENDIX 1- PHOTOS OF TEST SETUP Conduction Measurement Photos Radiated Measurement Photos

Page 27 of 27 Report No.: STS1805200W01 ※※※※※END OF THE REPORT※※※※※


Document Created: 2018-06-04 03:17:37
Document Modified: 2018-06-04 03:17:37
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC