with EUT description

FCC ID: JE4CSMDTN

Users Manual

Download: PDF
FCCID_157374

GENERAL DESCRIPTION COSMOS DT FEATURES CAUTION: The COSMOS family includes the following models: • Dual IR and MW Technologies THE UNIT SHOULD NOT BE MOUNTED IN DIRECT SUNLIGHT OR NEAR • Creep Zone ANY HEAT SOURCES. THE DETECTION SECTORS SHOULD BE POINTED • COSMOS PR: A microprocessor based Passive Infrared detector • Microprocessor Design TOWARDS EITHER A WALL OR THE FLOOR (NOT WINDOWS AND • COSMOS AM: Passive Infrared detector with anti-masking features. • Automatic True Temperature Compensation CURTAINS). INSTALL ON SMOOTH SURFACES ONLY. • COSMOS PET PR: A microprocessor based Passive Infrared detector with • Microwave Range Adjustment pet immunity • Pigmented Lenses • COSMOS PQ: A Quad PIR with two separate dual element pyroelectric • Alternate Polarity Pulse Count STEP 2 PRELIMINARY CONSIDERATIONS sensors. • Low Current Consumption • COSMOS DT: A Dual Technology detector offering both MW and IR • High RFI Immunity If a fixing screw is used to secure the front cover, turn the screw 3 full turns technologies. • Anti-Fluorescent Interference Signal Processing in the counterclockwise direction. With the screw now loosened, press it in • COSMOS DTAM: A Dual Technology detector with anti-masking features. • Wall and Corner Mounting Without Accessories to release the front cover. • COSMOS PET DT: A Dual Technology detector with pet immunity. • Vertical Adjustment If a screw is not used, press the tab located behind the screw hole. The front • UL Listed Versions cover can now be removed. LED display STEP 3 PC BOARD REMOVAL The cosmos DT is available in the following versions: + - TAMPER LEDS ON ALARM + C29 LED's jumper When LEDS Jumper is IN: Loosen the holding screw located on the right side of the PCB and slide the PCB DTI (UK) (10.687 GHz) RANGE FCC (USA) LEDS • YELLOW LED indicates +5V GND up until the screw enters the widened region. The PCB can now be lifted off. (10.525 GHz)UL Listed MU1 PIR detection MW RK - 210DTI 10m/ 33ft RK - 210FC • GREEN LED indicates C15 Module MW detection STEP 4 MOUNTING RK - 215DTI 15m/ 50ft RK - 215FC C28 XTL1 RK - 225DTI 25m/ 80ft RK - 225FC • RED LED indicates alarm PULSE The COSMOS DT can be mounted either on flat surface or at corner. (simultaneous PIR and Jumper a. Open the knockout holes on the rear cover. MW detection) b. Insert the cable through the cable hole. • At Powe-up period, the IF GND IR Sensor 1 T4 TC1 c. Mount the rear cover in its final location. The IR responds to changes in the ambient thermal radiation caused when Leds will blink PULSE S1 C19 OFF MW Range d. Seal the remaining holes with sealant. an intruder crosses the protected area. continuously, one after C1 Adjustment e. After mounting the back cover replace the PCB in its position. The MW transmits signals and analyzes the frequency changes of the the other, untill end of C6 C24 C21 reflected echo from an intruder due to Doppler effect. warm-up period. C25 Tamper PC BOARD ADJUSTMENT LONG C8 MICROWAVE SENSITIVITY Switch STEP 5 An ALARM is initiated only when both technologies trigger simultaneously. SHORT MIN MAX After the Detector base has been mounted, reinstall the PCB. Use the scale Detection occurs only in areas where IR and MW patterns overlap, greatly INSTALLATION on the bottom left side of the PCB to choose the correct vertical adjustment reducing the chance of false alarms. position as follows: STEP 1 PRELIMINARY CONSIDERATIONS For WIDE ANGLE LENS RK210/RK 215 installed at a height of 2.5m (8’2”) (for UL). Table 1: Available COSMOS DT Lenses and Accessories. Before installation, carefully study the space to be protected so as to choose the correct placement of the unit and lens for best coverage. SCALE POSITION ROOM SIZE ACCESSORY RK-225 RK-215 RK-210 The detector should be installed so that the beam patterns are at 45º short 3-6m (9-18ft) Typical Mounting Height 2.5m 2.5m 2m long 6-15m (18-50ft) (optimal) to the intruder's expected path. Corner installations are Wide Angle Lens RL-115 RL-125 recommended. Installation height should be between 1.8m (5’9”) and 2m RK-225 install at 2m (6’7”) at Long position only Long Range Lens *** *** RL-17 (6’7”) for the 225 and at an optional 2.5m (8’2”) for the RL-17. Use Fig 3 as reference. Fine Tuning of Protected Area: Corridor Lens RL-15 *** Slide the board up - to lower the beams and reduce the range. Pet Alley set RA-12 *** Slide the board down - to raise the beams and increase the range. The IR range is determined by the installation height. Use fig 3 as a NOTE Ceiling Mounted Swivel RA-90 *** For LONG RANGE: Select select position, LONG, Pulse Count of 1 and a reference. For ever y 10cm (4") of lowering (or increasing) the mounting height of 2.5m. Wall/Corner Mounted Swivel RA-91 *** installation height, the range is reduced (or increased) by 2.8m (9'2"). When completed, fasten the screw to secure the PCB in the desired position. 1 2 3

STEP 9 FINAL SETUP PROCEDURE FOR CHANGING LENSES STEP 6 TERMINAL WIRING The pigmented lens is attached to the inside of the front plastic cover using a sensor protective sleeve. Wire cable to the terminal block at the top of the PCB as follows: After completing the installation and testing stages, ensure all jumpers 1. Remove the sensor protecting sleeve by pushing up the clip that holds 12 VDC: Power supply input. are at their desired positions. The unit is now ready for normal use. the top part of the sleeve to the front cover. ALARM: Normaly closed output. 2. Disconnect the lens from the sleeve by gently lifting it from the holding TAMPER: Normaly closed dry output. pins that secure it to the sides of the sleeve. Fig 3: Cosmos DT Lenses 3. Select the desired lens and make sure that the cut corners are pointed upwards. (Fig. 4). TOP VIEW SIDE VIEW 4. Place the two pins, located on the top and bottom part of the lens, into STEP 7 JUMPER SETTING the matching holes on the sleeve. WIDE ANGLE (RL-115) 5. Place the holes on either side of the lens into their matching holding pins on the sides of the sleeve. RK-210/215 The COSMOS DT has two jumpers that can be either IN (used) or 2.5m OUT (unused). (8'2") 6. Insert the protective sleeve back into place on the front cover. 110 Unused jumpers should be placed on one leg only to prevent their loss. 0.4m 2m 5m 10m/15m (1'4") (6'7") (16'5") (33/49') Fig 2: Jumper positions. IN OUT Fig 4. Lens Change CORRIDOR (RL-15) RK-210/215 2.5m (8'2") Procedure 1.3m 1.1m /2m (3'3") This equipment has been tested and found to comply with the limits for a Class B digital device, N O T E 0.4m (1'4") 2.5m (8'2") 10m/15m (33/49') pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can LEDS: IN - Enables all LEDs radiate radio frequency energy and, if not installed and used in accordance with the instructions, OUT - Disables all LEDs cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio PULSE: IN - NO Pulse Count (1 pulse) or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures: OUT -Alternative Polarity Pulse Count (2 pulses) •Reorient or relocate the receiving antenna •Increase the separation between the equipment and the receiver RK-225 RL-125 WIDE ANGLE 2m (6'7") •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected STEP 8 WALK TEST 83 1.1m (3'3") •Consult the dealer or an experienced radio/TV technician for help. Changes or modifications to this equipment not expressly approved by the party responsible for 0.4m 3m 25m (1'4") (9'10") (82') compliance (Rokonet Electronics Ltd.) could void the user's authority to operate the equipment. Two minutes after applying power (a warm-up period), walk test the detector over the entire protected area to verify proper operation of the unit. SPECIFICATIONS NOTES FOR UL ELECTRICAL 1. The models have been listed by Underwriters The RK-225 needs a longer warm-up period of FOUR minutes. It enables a Current consumption: 19mA at 12 VDC 45mA at 16 VDC Laboratories for use with the wide angle lens powerful long range sensing capability and has increased sensitivity. (MAX with all LED's ON) Voltage requirements: 9-16 VDC regulated RK-225 (RL-17) only . LONG RANGE Alarm contacts: 24 VDC, 50 mA 2.5m • Make sure to replace front cover before Walk Test. (8'2") Tamper contacts: 24 VDC, 0.1A 2. The detector is intended to be connected to N O T E 3m 1.1m OPTICAL • The MW range can be adjusted using the potentiometer located at the (3'3") 0.4m 4m 23m Filtering: PHYSICAL White Light Protection a listed burglar alarm control unit capable bottom of the PCB. It is important to set the potentiometer to the lowest (1'4") (13'1") (75'5") Size: 127.6 x 64.2 x 40.9mm of providing 4 hours of standby power. (5 x 2.5 x 1.6 in.) possible setting that will still provide coverage for the entire ENVIRONMENTAL Specifications are subject to change without prior notice. Operating temperature: -10ºC to 55ºC (14ºF to 131ºF) protected area. Storage Temperature: -20ºC to 60ºC (-4ºF to 140ºF) Should any questions arise, contact your distributor. 4 5 6 ROKONET LIMITED WARRANTY Rokonet Electronics, Ltd. and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in materials and workmanship under normal use for 24 months from the date of production. Because Seller does not install or connect the product and because the product may be used in conjunction with products not manufactured by the Seller, Seller can COSMOS not guarantee the performance of the security system which uses this product. Sellers obligation and liability under this warranty is expressly limited to repairing and replacing, at Sellers option, within a reasonable time after the date of delivery, DT SERIES any product not meeting the specifications. Seller makes no other warranty, expressed or implied, and makes no warranty RK-210,215,225 of merchantability or of fitness for any particular purpose. In no case shall seller be liable for any consequential or incidental ROKONET ELECTRONICS LTD. damages for breach of this or any other warranty, expressed or implied, or upon any other basis of liability whatsoever. 14 HACHOMA ST. Sellers obligation under this warranty shall not include any transportation charges or costs of installation or any liability for direct, indirect, or consequential damages or delay. 75655 RISHON LETZION. ISRAEL. Seller does not represent that its product may not be compromised or circumvented; that the product will prevent any persona; TEL: (972) 3 961 6555 FAX: (972) 3 961 6584 injury or property loss by burglary, robbery, fire or otherwise; or that the product will in all cases provide adequate warning I N S TA L L AT I O N or protection. Buyer understands that a properly installed and maintained alarm may only reduce the risk of burglary, INSTRUCTIONS robbery or fire without warning, but is not insurance or a guaranty that such will not occur or that there will be no personal ROKONET USA: TEL: 1 914 592 1068 FAX: 1 914 592 1271 injury or property loss as a result. ROKONET UK: TEL: 44 (0) 1527 576 765 FAX: 44 (0) 1527 576 816 Consequently seller shall have no liability for any personal injury, property damage or loss based on a claim that the product ROKONET FRANCE: TEL: 33 (0) 155 123390 FAX: 33 (0) 148 863042 fails to give warning. However, if seller is held liable, whether directly or indirectly, for any loss or damage arising from ROKONET ITALY: TEL: 39 (02) 3925 354 FAX: 39 (02) 3925 131 under this limited warranty or otherwise, regardless of cause or origin, sellers maximum liability shall not exceed the purchase ROKONET BRAZIL: TEL: 55 (21) 496.3544 FAX: 55 (21) 496.3547 price of the product, which shall be complete and exclusive remedy against seller. No employee or representative of Seller is authorized to change this warranty in any way or grant any other warranty. WARNING: This product should be tested at least once a week. © 2001 Rokonet Electronics Ltd 7in71fmb 05/01


Document Created: 2001-06-05 11:15:21
Document Modified: 2001-06-05 11:15:21
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC