MPE Report

FCC ID: J9CMTP9900LAA

RF Exposure Info

Download: PDF
FCCID_3078631

PCTEST ENGINEERING LABORATORY, INC. 6660-B Dobbin Road, Columbia, MD 21045 USA Tel. 410.290.6652 / Fax 410.290.6554 http://www.pctestlab.com RF EXPOSURE EVALUATION Maximum Permissible Exposure (MPE) Applicant Name: Date of Testing: Qualcomm Technologies, Inc. 12/23/2015-3/5/2016 5775 Morehouse Drive Test Site/Location: San Diego, CA 92121 PCTEST Lab, Columbia, MD, USA United States Test Report Serial No.: 0Y1607131260-R2.J9C FCC ID: J9CMTP9900LAA APPLICANT: Qualcomm Technologies, Inc. EUT Type: LAA Release 13 Small Cell FCC Rule Part(s): FCC Part 1 (§1.1310) and Part 2 (§2.1091) FCC Classifications: PCS Licensed Transmitter (PCB), Unlicensed National Information Infrastructure (NII) Test Procedure: KDB 447498 D01 v06 The device bearing the FCC Identifier specified above has been shown to comply with the applicable technical standards as indicated in the measurement report and has been tested in accordance with the measurement procedures specified in FCC KDB 447498 D01 v06. These measurements were performed with no deviation from the standards. Test results reported herein relate only to the item(s) tested. This revised Test Report (S/N: 0Y1607131260-R2.J9C) supersedes and replaces the previously issued test report (S/N: 0Y1607131260-R1.J9C) on the same subject device for the same type of testing as indicated. Please discard or destroy the previously issued test report(s) and dispose of it accordingly. I authorize and attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Reviewed by: FCC ID: J9CMTP9900LAA MAXIMUM PERMISSIBLE EXPOSURE (MPE) DATA REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 8 0Y1607131260-R2.J9C 12/23/2015-3/5/2016 LAA Release 13 Small Cell © 2016 PCTEST Engineering Laboratory, Inc. REV 3.2MPE 7/27/2012

T A B L E O F C O N T E N T S 1.0 RF EXPOSURE EVALUATION – MAXIMUM PERMISSIBLE EXPOSURE (MPE) ......................... 3 1.1 Introduction ............................................................................................................................................ 3 1.2 EUT Description..................................................................................................................................... 3 1.3 MPE Requirements Overview ................................................................................................................ 4 1.4 Procedure .............................................................................................................................................. 5 1.5 Simultaneous Transmission ................................................................................................................... 7 2.0 CONCLUSION .................................................................................................................................. 8 Reviewed by: FCC ID: J9CMTP9900LAA MAXIMUM PERMISSIBLE EXPOSURE (MPE) DATA REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 8 0Y1607131260-R2.J9C 12/23/2015-3/5/2016 LAA Release 13 Small Cell © 2016 PCTEST Engineering Laboratory, Inc. REV 3.2MPE 7/27/2012

1.0 RF EXPOSURE EVALUATION – MAXIMUM PERMISSIBLE EXPOSURE (MPE) 1.1 Introduction This document is prepared on behalf of Qualcomm Technologies, Inc. to show compliance with the RF Exposure requirements as required in §1.1310 of the FCC Rules and Regulations. The limit for Maximum Permissible Exposure (MPE), specified in FCC §1.1310, is listed in Table 1-1 below. According to FCC §1.1310: the criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in §1.1307(b). Frequency Electric Field Magnetic Field Power Density Average Time Range (MHz) Strength (V/m) Strength (A/m) (mW/cm2) (Minutes) (A) Limits For Occupational / Control Exposures (f = frequency) 30-300 61.4 0.163 1.0 6 300-1500 … … f/300 6 1500-100,000 … … 5.0 6 (B) Limits For General Population / Uncontrolled Exposure (f = frequency) 30-300 27.5 0.073 0.2 30 300-1500 … … f/1500 30 1500-100,000 … … 1.0 30 Table 1-1. Limits for Maximum Permissible Exposure (MPE) 1.2 EUT Description The Qualcomm LAA Release 13 Small Cell Model: MTP9900 is a 2x2 Tx system that uses two LTE carriers to transmit simultaneously in a licensed band and an unlicensed band. It is also possible to transmit on a 40MHz channel by using both LTE carriers in the unlicensed band at the same time. The test hardware SKU identification number is 65-F5230-910. For this MPE evaluation, the power density is determined from the highest measured conducted power in LTE and LAA modes along with the addition of a 6dBi max antenna gain. EUT: Model: MTP9900LAA SKU NUMBER: 65-F5230-910 MCN NUMBER: 10-F5230-006 Grantee: Qualcomm Technologies, Inc. FCC ID: J9CMTP9900LAA Antenna(s): The maximum antenna gain that will be used with this device is 6dBi Reviewed by: FCC ID: J9CMTP9900LAA MAXIMUM PERMISSIBLE EXPOSURE (MPE) DATA REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: Page 3 of 8 0Y1607131260-R2.J9C 12/23/2015-3/5/2016 LAA Release 13 Small Cell © 2016 PCTEST Engineering Laboratory, Inc. REV 3.2MPE 7/27/2012

1.3 MPE Requirements Overview Three different categories of transmitters are defined by the FCC KDB 447498 D01 v06. These categories are fixed installation, mobile, and portable and are defined as follows: o Fixed Installations: fixed location means that the device, including its antenna, is physically secured at a permanent location and is not able to be easily moved to another location. Additionally, distance to humans from the antenna is maintained to at least 2 meters. o Mobile Devices: a mobile device is defined as a transmitting device designed to be used in other than fixed locations and to be generally used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitter's radiating structures and the body of the user or nearby persons. Transmitters designed to be used by consumers or workers that can be easily re-located, such as a wireless modem operating in a laptop computer, are considered mobile devices if they meet the 20 centimeter separation requirement. The FCC rules for evaluating mobile devices for RF compliance are found in 47 CFR §2.1091. o Portable Devices: a portable device is defined as a transmitting device designed to be used so that the radiating structure(s) of the device is/are within 20 centimeters of the body of the user. Portable device requirements are found in Section 2.1093 of the FCC's Rules (47 CFR§2.1093). The FCC also categorizes the use of the device as based upon the user’s awareness and ability to exercise control over his or her exposure. The two categories defined are Occupational/ Controlled Exposure and General Population/Uncontrolled Exposure. These two categories are defined as follows: o Occupational/Controlled Exposure: In general, occupational/controlled exposure limits are applicable to situations in which persons are exposed as a consequence of their employment, who have been made fully aware of the potential for exposure and can exercise control over their exposure. This exposure category is also applicable when the exposure is of a transient nature due to incidental passage through a location where the exposure levels may be higher than the general population/uncontrolled limits, but the exposed person is fully aware of the potential for exposure and can exercise control over his or her exposure by leaving the area or by some other appropriate means. Awareness of the potential for RF exposure in a workplace or similar environment can be provided through specific training as part of a RF safety program. If appropriate, warning signs and labels can also be used to establish such awareness by providing prominent information on the risk of potential exposure and instructions on methods to minimize such exposure risks. o General Population/Uncontrolled Exposure: The general population / uncontrolled exposure limits are applicable to situations in which the general public may be exposed or in which persons who are exposed as a consequence of their employment may not be made fully aware of the potential for exposure or cannot exercise control over their exposure. Members of the general public would come under this category when exposure is not employment-related; for example, in the case of a wireless transmitter that exposes persons in its vicinity. Warning labels placed on low-power consumer devices such as cellular telephones are not considered sufficient to allow the device to be considered under the occupational/controlled category, and the general population/uncontrolled exposure limits apply to these devices. The Qualcomm LAA Release 13 Small Cell FCC ID: J9CMTP9900LAA is evaluated to the Mobile Device requirements and is considered a device to be used by the General Population/Uncontrolled Exposure. Reviewed by: FCC ID: J9CMTP9900LAA MAXIMUM PERMISSIBLE EXPOSURE (MPE) DATA REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: Page 4 of 8 0Y1607131260-R2.J9C 12/23/2015-3/5/2016 LAA Release 13 Small Cell © 2016 PCTEST Engineering Laboratory, Inc. REV 3.2MPE 7/27/2012

1.4 Procedure The procedure used to determine the RF power density was based upon a calculation for determining compliance with the MPE requirements. The power generated by each antenna output used in this product was initially measured by a spectrum analyzer and the powers were recorded. Through use of the Friis transmission formula and knowledge of the maximum 6dBi antenna gain to be used, the power density level is calculated at a distance of 20cm. Friis Transmission Formula Friis transmission formula: Pd = (Pout*G) / (4πr2) Where, Pd = Power Density (mW/cm2) π = 3.1416 Pout = output power to antenna (mW) r = distance between observation point and center of the radiator (cm) G = gain of antenna in linear scale Calculated MPE The power density limit for General Population/Uncontrolled Exposure at each frequency is determined based on the information in Table 1-1. There is no co-location between the electric fields of any two transmitters therefore following power densities are calculated for each individual transmitter by frequency at 20cm spacing: Frequency 1940 MHz Limit 1.000 mW/cm^2 Distance (cm), R = 20 cm Power (dBm), P = 24.47 dBm 279.90 mW TX Ant Gain (dBi), G = 6 dBi Power Density (S) = 0.222 mW/cm^2 (at 20cm) Minimum Distance = 9.4 cm Table 1-2. Calculated MPE Data for LTE Band 4 (Chain0) Frequency: 2115 MHz Limit: 1.000 mW/cm^2 Distance (cm), R = 20 cm Power (dBm), P = 24.39 dBm 274.79 mW TX Ant Gain (dBi), G = 6 dBi Power Density (S) = 0.218 mW/cm^2 (at 20cm) Minimum Distance = 9.3 cm Table 1-3. Calculated MPE Data for LTE Band 2 (Chain0) Reviewed by: FCC ID: J9CMTP9900LAA MAXIMUM PERMISSIBLE EXPOSURE (MPE) DATA REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: Page 5 of 8 0Y1607131260-R2.J9C 12/23/2015-3/5/2016 LAA Release 13 Small Cell © 2016 PCTEST Engineering Laboratory, Inc. REV 3.2MPE 7/27/2012

Frequency 5795 MHz Limit 1.000 mW/cm^2 Distance (cm), R = 20 cm Power (dBm), P = 24.22 dBm 264.24 mW TX Ant Gain (dB), G = 6 dBi Power Density (S) = 0.209 mW/cm^2 (at 20cm) Minimum Distance = 9.1 cm Table 1-4. Calculated MPE Data for LAA 5GHz Band (Chain0) Frequency 2117.5 MHz Limit 1.000 mW/cm^2 Distance (cm), R = 20 cm Power (dBm), P = 24.42 dBm 276.69 mW TX Ant Gain (dBi), G = 6 dBi Power Density (S) = 0.219 mW/cm^2 (at 20cm) Minimum Distance = 9.4 cm Table 1-5. Calculated MPE Data for LTE Band 4 (Chain1) Frequency: 1937.5 MHz Limit: 1.000 mW/cm^2 Distance (cm), R = 20 cm Power (dBm), P = 24.47 dBm 279.90 mW TX Ant Gain (dBi), G = 6 dBi Power Density (S) = 0.222 mW/cm^2 (at 20cm) Minimum Distance = 9.4 cm Table 1-6. Calculated MPE Data for LTE Band 2 (Chain1) Frequency 5825 MHz Limit 1.000 mW/cm^2 Distance (cm), R = 20 cm Power (dBm), P = 24.21 dBm 263.63 mW TX Ant Gain (dB), G = 6 dBi Power Density (S) = 0.209 mW/cm^2 (at 20cm) Minimum Distance = 9.1 cm Table 1-7. Calculated MPE Data for LAA 5GHz Band (Chain1) Reviewed by: FCC ID: J9CMTP9900LAA MAXIMUM PERMISSIBLE EXPOSURE (MPE) DATA REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: Page 6 of 8 0Y1607131260-R2.J9C 12/23/2015-3/5/2016 LAA Release 13 Small Cell © 2016 PCTEST Engineering Laboratory, Inc. REV 3.2MPE 7/27/2012

Frequency 5745 MHz Limit 1.000 mW/cm^2 Distance (cm), R = 20 cm Power (dBm), P = 15.58 dBm 36.14 mW TX Ant Gain (dB), G = 6 dBi Power Density (S) = 0.029 mW/cm^2 (at 20cm) Minimum Distance = 3.4 cm Table 1-8. Calculated MPE for 802.11a WiFi 1.5 Simultaneous Transmission Simultaneous transmission results are calculated by adding the highest EIRP in LTE Band 2 or Band 4 and adding it to the highest 5GHz EIRP to compare with its respective power density limits. This is performed for both chains such that a total of 4 transmitters are active. Percent Power Density Limit MPE Used (mW/cm^2) (mW/cm2) (%) Transmitter #1 (LTE Ch0) 0.222 1.000 22.17 Transmitter #2 (LTE Ch1) 0.222 1.000 22.17 Transmitter #3 (LAA Ch0) 0.209 1.000 20.93 Transmitter #4 (LAA Ch1) 0.209 1.000 20.88 Total 86.14 Table 1-9. Calculated MPE Data for Simultaneous Tx Reviewed by: FCC ID: J9CMTP9900LAA MAXIMUM PERMISSIBLE EXPOSURE (MPE) DATA REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: Page 7 of 8 0Y1607131260-R2.J9C 12/23/2015-3/5/2016 LAA Release 13 Small Cell © 2016 PCTEST Engineering Laboratory, Inc. REV 3.2MPE 7/27/2012

2.0 CONCLUSION The device meets the mobile RF exposure limit at a 20cm separation distance as specified in §2.1091 of the FCC Rules and Regulations. Reviewed by: FCC ID: J9CMTP9900LAA MAXIMUM PERMISSIBLE EXPOSURE (MPE) DATA REPORT Quality Manager Test Report S/N: Test Dates: EUT Type: Page 8 of 8 0Y1607131260-R2.J9C 12/23/2015-3/5/2016 LAA Release 13 Small Cell © 2016 PCTEST Engineering Laboratory, Inc. REV 3.2MPE 7/27/2012


Document Created: 2017-12-11 04:29:45
Document Modified: 2017-12-11 04:29:45
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC