Report

FCC ID: J2MPM5

Test Report

Download: PDF
FCCID_2286381

Serial No. GM214045f FCC ID: J2MPM5 FCC TEST REPORT FOR THE CONCEPT2, INC. MODEL PM5 PERFORMANCE MONITOR FCC ID: J2MPM5 Prepared for: Concept2, Inc. 105 Industrial Park Drive Morrisville, VT 05661 USA Submitted by: Green Mountain Electromagnetics, Inc. GME (802) 388-3390 (802) 388-6279 Fax gme@gmelectro.com 219 Blake Roy Road • Middlebury, Vermont 05753 Copyright: June 2, 2014 Test Lab Cert 898.01 This report shall not be reproduced, except in full, without the written approval of GME.

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 Concept2, Inc. FCC Testing At Green Mountain Electromagnetics, Inc. Units: Model PM5 Performance Monitor Received: 5/19/14 Tested: May 21 - 23, 2014 I. Applicable Standards: The units described in this report were measured for verification of compliance with "47 CFR, Part 15 – Radio Frequency Devices, Subpart C: Intentional Radiators," paragraph 15.209, Radiated Emissions and 15.249, Operation within the 2400 – 2483.5 MHz Band. Measurement procedures were in accordance with ANSI C63.4, "Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz (2009)," and FCC OET Bulletin 65, "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields (Jan. 2001)." Additionally, the units described in this report were measured for certification with the Code of Federal Regulations Chapter 47 – "Telecommunication, Part 2 – Frequency Allocations and Radio Treaty Matters: General Rules and Regulations, Subpart J – Equipment Authorization Procedures." Measurements required were per paragraphs 2.1046 RF Power Output, 2.1047 Modulation Characteristics, 2.1049 Occupied Bandwidth, 2.1053 Field Strength of Spurious Radiation, 2.1055 Frequency Stability and 2.1093 Radiofrequency Radiation Exposure Evaluation: Portable Devices. II. Measurement Location: The GME laboratory and Open Area Test Site (OATS) are located at 219 Blake Roy Road, Middlebury, VT. The OATS is a 10/3/1-meter site complete with antenna positioner, ground plane and motorized turntable. The OATS is constructed in accordance with ANSI C63.7-2005 and complies with the requirements for radiated emissions testing in ANSI C63.4-2009 and CISPR standards. GME is internationally accredited by the American Association for Laboratory Accreditation (A2LA) and meets the quality requirements in ISO/IEC 17025 (2005), "General Requirements for the Competence of Testing and Calibration Laboratories." Page 2 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 III. Unit Tested: The Concept2, Inc. Model PM5 is a performance monitor used in stationary training equipment for data logging/analysis and battery recharging. The PM5 uses DC-battery power and is controlled by a front-panel, LCD-touchpad interface. It consists of the plastic enclosure, signal connectors, the electronics, and the power input circuit. The PM5 has wireless capability using two, 2.4-GHz transceivers (Nordic Semiconductor nRF51422/nRF51822 set for -4 dBm power output and using channels 1-80). The PM5 is intended for use in a residential environment. Model PM5 was connected to electrical loads to represent actual use of the products during testing. The table below describes the units that were subjected to measurements determining compliance with applicable standards: The following table describes the system physical and electrical properties: Model Volts/Amps H/W/D in cm Serial # PM5 3 VDC, two “D” cells 16/12/7 310 The following table describes the support equipment used during testing: Product Manufacturer Model Laptop PC Apple A1005 Performance Monitors (2) Concept2 PM4 USB Drive ADATA 4GB Generator Concept2 n/a Power/signal cables were used for testing and are supplied by the manufacturer. The following table describes the unit cable: Cable Manufacturer Description Signal Jamer USB 2.0, UL E219485 Signal (2) CM Cat 5e Ethernet , UL E305668 Power/Signal Concept2 2.5 mm Jack Page 3 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 IV. Summary of Results: The Concept2, Inc. Model PM5 complies with 47 CFR, Parts 2 and 15. Section X contains the results summarized in the table below. CFR 47 Frequency Specified Measured Test Mode/Port Paragraph Range/Level Values Values 1 Output Power Transmit 2.1046 2.4 – 2.4835 94 dBuV/m 92 dBuV/m 15.249(a) GHz 2 Modulation Transmit 2.1047(d) All modulation Per Within Characteristic products ANT+ Manufacturer Tolerance & Bluetooth 3 Occupied Transmit 2.1049(h) 2.4 – 2.4835 50 dB down >50 dB Bandwidth 15.249(d) GHz outside OBW 4 Frequency Transmit 2.1055 2439.980 MHz Battery End 2439.980 MHz Stability -30˚C to +50˚C 5 Radiated and Enclosure 15.209 30 – 88 MHz 40 dBuV/m Within Spurious 15.249 88 – 216 MHz 43.5 dBuV/m All Limits Emissions 2.1053 216 – 960 MHz 46 dBuV/m 960 – 24 GHz 54 dBuV/m 6 Exposure Enclosure 2.1093 2.4 – 2.4835 0.08 W/kg Within Evaluation GHz Body All Limits 1.6 W/kg 1g Volume Exploratory measurements indicate maximum radiation is found when the antenna polarization is aligned with the EUT antenna and when the antenna is pointed directly at the EUT at scan heights >10% of EUT height. Testing was performed by Kyle R. Kowalczyk, president, Green Mountain Electromagnetics and requested by: Concept2, Inc. 105 Industrial Park Drive Morrisville, VT 05661 USA ___________________________ Kyle R. Kowalczyk 6/2/14 Page 4 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 V. Equipment, Software and Cable Configuration: GME witnessed the unit in satisfactory condition for testing, however the manufacturer is responsible for ensuring that the equipment under test (EUT) represents the product line. The manufacturer is also responsible for the test plan and for assuring that this report is consistent with that plan. The EUT was operating in a continuous mode utilizing and testing its monitoring functions. The EUT was also tested upon power up. The EUT configuration was arranged to produce maximum radiated emissions as shown in the block diagram below. The equipment was subjected to complete emissions tests per the manufacturer’s test plan. Antenna @ 3 Meters <1 GHz EUT Support Antenna @ 1 Meter >1 GHz Ground Plane Block Diagram of FCC ID J2NPM5 VI. Units of Measurement and Uncertainty: Measurements of radiated electric fields were made in units of dB referenced to 1 microvolt per meter (dBuV/m). Limits appearing on the spectrum analyzer data were corrected for the appropriate antenna factor, cable loss, amplifier gain (when used) and measurement distances Xstd and Xsite in meters. The following equation was employed: Corrected Limit (dBuV) = Limit (dBuV/m) + 20 Log(Xstd/Xsite) + Amplifier Gain (dB) – Antenna Factor (dB/m) – Cable Loss (dB). Sample calculation at 30 MHz (Vertical Polarization): 51.8 dBuV corrected limit = 40.0 dBuV/m limit + 20 log(3/3) dB distance + 30 dB amp gain – 17.2dB/m AF – 1 dB cable loss. Page 5 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 Uncertainty The uncertainty budgets in GME EMC measurements are identified as follows: 1. Field strength between 30 MHz and 26 GHz on a three-meter OATS using broadband antennas: Contribution Probability Distribution Uncertainty (dB) antenna factor calibration normal k=2 0.5 cable loss calibration normal k=2 0.5 analyzer specification rectangular 1.5 distance variation rectangular 0.6 height variation rectangular 0.5 site imperfection rectangular 2.0 mismatch u-shaped 1.5 repeatability standard deviation 0.5 combined uncertainty u(y) normal 1.946 expanded uncertainty U normal k=2 3.892 0.5 2 0.5 2 1.5 2 + 0.6 2 + .5 2 + 2.0 2 1.5 2 u(y) = ( ) +( ) + + + 0.5 2 2 2 3 2 U = k u(y) € Other GME uncertainty values are available upon request. Note: "U" represents an expanded uncertainty expressed at an approximately 95% confidence level using a coverage factor of k=2. VII. Measuring Equipment: The table below describes the instrumentation used by Green Mountain Electromagnetics to perform this testing: Unit Manufacturer Model Serial # Last Cal. Next Cal. Spectrum HP 8592L 3624A00631 12/2/13 12/2/14 Analyzer Spectrum GW Instek GSP-830 E1180708 9/11/13 9/11/14 Analyzer Broadband ARA LPB-2513/A 1224 11/04/13 11/04/14 E-field Antenna Horn Antenna EMCO 3115 2418 10/10/13 10/10/14 Page 6 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 Pre-Amplifier MiniCircuits ZKL-2R5+ 739045986 11/19/13 11/19/14 Power Amplifier MiniCircuits ZVE-8G n/a 1/7/14 1/7/15 Weather Station Davis Insts. Perception II PC30923A07 1/22/14 1/22/15 E-field Meter Wandel & EMR-30 F-0049 10/18/13 10/18/14 w/ Probe Goltermann w/ 2244/90.21 F-0038 w/NARDA Temperature- PTC RHTemp101 N00532 8/8/13 8/8/14 Humidity Probe Temperature- Thermotron SM8S 25-2300-04 n/a n/a Humidity Chamber VIII. Measurement Procedures: 1. RF Power Output. Specification: <50,000 uV/m (100% Duty) @ 3m a. Set up EUT on OATS and test instrumentation in laboratory. b. Verify spectrum analyzer and EUT operation. i. Spectrum analyzer uses internal attenuators. ii. Set analyzer to carrier frequency and use span >OBW. c. Operate EUT at normal power unmodulated. d. Record level displayed on analyzer. 2. Modulation Characteristic. Specification: Modulation Products per Bluetooth and ANT+ a. Set up EUT on OATS and test instrumentation in laboratory. b. Verify analyzer and EUT operation. i. Spectrum analyzer uses internal attenuators. ii. Set analyzer to carrier frequency and use span necessary to view all modulation products. c. Operate EUT with standard modulation. d. Record signal displayed on analyzer. 3. Occupied Bandwidth. Specification: 50-dB down outside 2.4 – 2.4835 GHz a. Set up EUT and test instrumentation in laboratory. b. Verify analyzer and EUT operation. Page 7 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 i. Spectrum analyzer uses internal attenuators. ii. Set analyzer to carrier frequency and use RBW <10 % of span. c. Operate EUT with standard modulation. d. Record signal displayed on analyzer. 4. Frequency Stability. Frequency Band: 2.4 – 2.4835 GHz Voltage Specification: Battery End Point Normal Operation a. Set up EUT in temperature chamber and test instrumentation in laboratory. b. Verify analyzer and EUT operation. i. Spectrum analyzer uses internal attenuators. ii. Set analyzer to carrier frequency and use narrowband span. c. Operate EUT with standard modulation. d. Record signal displayed on analyzer for high/low temperature and voltage. 5. Radiated Emissions. Frequency range: 30 MHz to 88 MHz Limit: 40 dBuV/m @ 3 meters Frequency range: 88 kHz to 216 MHz Limit: 43.5 dBuV/m @ 3 meters Frequency range: 216 MHz to 960 MHz Limit: 46 dBuV/m @ 3 meters Frequency range: 960 MHz to 25 GHz & Spurious >960 MHz Limit: 54 dBuV/m @ 3 meters a. Set up instrumentation at open area test site. i. Mount EUT on ground plane and broadband antenna on antenna positioner. ii. Observe temperature, humidity and atmospheric pressure. iii. Measurement distance is 3 meters <1 GHz/1 meter >1 GHz and antenna scan height is 1 to 4 meters. Use RF absorber on ground plane >1 GHz. b. Verify spectrum analyzer and antenna operation. i. Spectrum analyzer is connected to antenna. Use broadband horn >1 GHz. ii. Preamplifier is inserted between antenna and analyzer to ensure analyzer noise thres- hold is at least 6 dB below specification limit. c. Set up, power and operate EUT as in block diagram in Section V. d. Perform preliminary evaluation of equipment in the near field. i. Vary antenna height, antenna polarization, and antenna orientation to EUT. ii. Repeat step d.i. while evaluating radiation in the 30-MHz to 25 GHz spectrum. iii. Refer to ANSI C63.4-2009: for exploratory measurements >1 GHz. e. Determine frequencies and equipment orientations that produce maximum radiation. Page 8 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 i. Identify processor, clock and beat frequencies, and harmonics. f. Perform final evaluation of unit by recording spectrum analyzer data. i. Ensure the EUT is producing the maximum radiation found in step e. ii. Collect data over the entire frequency range. iii. Refer to ANSI C63.4-2009: for final measurements >1 GHz – Manually ensure measurement antenna is in cone of radiation for emission areas determined in steps d.-e. by adjusting in both azimuth and elevation positions. Polarization is oriented for maximum response. 6. Exposure Evaluation. Frequency: 2.4 GHz Limit: 0.8 W/kg and 1.6 W/kg a. Set up instrumentation at open area test site. i. Mount EUT on table and isotropic probe or loop on antenna positioner. ii. Observe temperature, humidity and atmospheric pressure. iii. Measurement distance is 1 meter and antenna scan height is varied over human body dimensions (0.1 to 2 meters). b. Verify E-field meter operation. c. Set up, power and operate EUT as described in Section V. d. Perform preliminary evaluation of equipment in the near field. i. Vary probe height, probe polarization, and probe orientation to EUT. ii. Repeat step d.i. while evaluating electromagnetic radiation at 2.4 GHz. iv. Near field measurements of unit emissions are made at ambient frequencies. e. Determine equipment orientations that produce maximum radiation. i. Set peak hold on meter for 30 minutes while slowly varying probe height. f. Perform final evaluation of unit by recording spectrum analyzer data. i. Ensure the EUT is producing the maximum radiation found in step e. ii. Collect data over the entire frequency range. iii. Identify all ambient signals. Page 9 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 IX. Photographs of Measurement Setup: The following pages are photographs of the equipment as it was tested. Photograph 1 – EUT on OATS <1 GHz Page 10 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 Photograph 2 – EUT on OATS >1 GHz Page 11 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 Photograph 3 – EUT in T/H Chamber Page 12 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results: 1. RF Power Output. Specification Specification Amplifier Antenna Cable Corrected Factor Loss Limit uV/m dBuV/m dB dB dB dBuV 50,000 94 30.0 29.0 1 94 Table 1 – RF-Power Corrected Limit Corrected Power (dBm) = Specification (dBuV/m) + Amplifier (dB) – Antenna Factor (dB/m) – Cable Loss (dB). PM5 nRF51422 Page 13 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results: 1. RF Power Output. Specification Specificatio Amplifier Antenna Cable Corrected n Factor Loss Limit uV/m dBuV/m dB dB dB dBuV 50,000 94 30.0 29.0 1 94 Table 2 – RF-Power Corrected Limit Corrected Power (dBm) = Specification (dBuV/m) + Amplifier (dB) – Antenna Factor (dB/m) – Cable Loss (dB). PM5 nRF51822 Page 14 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 2. Modulation Characteristic. Black trace is Bluetooth, Brown trace is ANT+. PM5 nRF51422 6 MHz Page 15 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 2. Modulation Characteristic. Black trace is Bluetooth. PM5 nRF51822 Page 16 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 3. Occupied Bandwidth. PM5 nRF51422 Page 17 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 3. Occupied Bandwidth. PM5 nRF51822 Page 18 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 4. Frequency Stability. Frequency: 2439.980 MHz Specification: 3 VDC (Normal Operation) The graph below is the baseline for the measurements. Page 19 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 4. Frequency Stability. Frequency: 2439.980 MHz Specification: 3 VDC to Battery End (Normal Operation) The tables below show that there is not any variation in frequency with selected applied voltage or temperature: Voltage (VDC) Frequency (MHz) 3 2439.980 2.8 2439.980 2.6 2439.980 Table 3 – Frequency Vs. Voltage – PM5 Temperature (˚C) Frequency (MHz) -30 2439.980 -20 2439.980 -10 2439.980 0 2439.980 10 2439.980 20 2439.980 30 2439.980 40 2439.980 50 2439.980 Table 4 – Frequency Vs. Temperature – PM5 Page 20 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 5. Radiated Emissions. Vertical Polarization The table below describes the correction factors necessary to apply the limit to the spectrum analyzer output. The following page contains the spectrum analyzer output with the corrected specification limits superimposed. The green trace is the ambient condition, and the orange trace identifies EUT emissions. Maximum amplitudes of vertical polarization are shown in the results below. Note: Occasional known ambient signals may persist (e.g. local AM/FM/Cell). Unit produced no discernible emissions so data is interpolated through any known ambient signal. Units producing in-band emissions are examined at nearer measurement distances. Frequency IR limit @ Amp Antenna Cable Corrected 3m Gain Factor Loss Limit MHz dBuV dB dB dB dBuV 30 40 30 17.2 1 51.8 50 40 30 13.6 1 55.4 88 40 30 7.5 1 61.5 89 43.5 30 7.5 1 65.0 125 43.5 30 8.9 2 62.6 150 43.5 30 12.2 3 58.3 216 43.5 30 11.6 3 58.9 217 46 30 11.6 3 61.4 300 46 30 13.9 3 59.1 500 46 30 16.9 6 53.1 960 46 30 23.2 8 44.8 961 54 30 23.2 8 52.8 Table 5 – Corrected Limit - Vertical Polarization Page 21 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 5. Radiated Emissions. PM5 Maximum of Vertical Polarization All Ambient – No Discernible Emissions in Near Field FM & TV Cell & FCC IR Limit PCS Page 22 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 5. Radiated Emissions. Horizontal Polarization The table below describes the correction factors necessary to apply the limit to the spectrum analyzer output. The following page contains the spectrum analyzer output with the corrected specification limits superimposed. The green trace is the ambient condition, and the orange trace identifies EUT emissions. Maximum amplitudes of horizontal polarization are shown in the results below. Note: Occasional known ambient signals may persist (e.g. local AM/FM/Cell). Unit produced no discernible emissions so data is interpolated through any known ambient signal. Units producing in-band emissions are examined at nearer measurement distances. Frequency IR limit @ Amp Antenna Cable Corrected 3m Gain Factor Loss Limit MHz dBuV dB dB dB dBuV 30 40 30 16.2 1 52.8 50 40 30 14.8 1 54.2 88 40 30 6.7 1 62.3 89 43.5 30 6.7 1 65.8 125 43.5 30 10.3 2 61.2 150 43.5 30 12.3 3 58.2 216 43.5 30 11.6 3 58.9 217 46 30 11.6 3 61.4 300 46 30 13.3 3 59.7 500 46 30 16.6 6 53.4 960 46 30 22.8 8 45.2 961 54 30 22.8 8 53.2 Table 6 – Corrected Limit - Horizontal Polarization Page 23 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 5. Radiated Emissions. PM5 Maximum of Horizontal Polarization All Ambient – No Discernible Emissions in Near Field FM & TV Cell & FCC IR Limit PCS Page 24 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 5. Radiated Emissions. Vertical & Horizontal Polarization >1 GHz. The table below describes the correction factors necessary to apply the limit to the spectrum analyzer output. The following pages contain the spectrum analyzer output with the corrected specification limits superimposed. The green trace is the ambient condition, and the orange trace identifies EUT emissions. Maximum amplitudes of both polarizations are shown in the results below. Frequency IR limit Amp Antenna Cable Corrected @ 3m Gain Factor Loss Limit MHz dBuV dB dB dB dBuV 1000 54 30 24 3 57 2400 54 30 28 6 50 2750 54 30 31 7 46 Table 7 – Corrected Limit - >1 GHz Page 25 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 5. Radiated Emissions. PM5 Maximum of Vertical Polarization FCC IR Limit Page 26 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 5. Radiated Emissions. PM5 Maximum of Horizontal Polarization FCC IR Limit Page 27 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 5. Radiated Emissions. Vertical & Horizontal Polarization >3 GHz. The table below describes the correction factors necessary to apply the limit to the spectrum analyzer output. The following page contains the spectrum analyzer output with the corrected specification limits superimposed. The black trace is the ambient condition, and the green trace identifies EUT emissions. Maximum amplitudes of both polarizations are shown in the results below. Frequency IR limit Distance Amp Antenna Cable Corrected @3m Correction Gain Factor Loss Limit *Note GHz dBuV dB dB dB dB dBuV 3 54 20 40 35.0 8 71 25 54 20 40 46.0 12 56 Table 8 – Corrected Limit - >3 GHz • Unit brought to 30 cm of antenna. • Near field at >3 GHz is <10 cm, so antenna is not in reactive field of EUT. Limits appearing on the spectrum analyzer data were corrected for the appropriate antenna factor, cable loss, amplifier gain (when used) and measurement distances Xstd and Xsite in meters. The following equation was employed: • Corrected Limit (dBuV) = Limit (dBuV/m) + 20 Log(Xstd/Xsite) + Amplifier Gain (dB) – Antenna Factor (dB/m) – Cable Loss (dB). • Sample calculation at 2750 MHz: • 71 dBuV corrected limit = 54.0 dBuV/m limit + 20 log(3/0.3) dB distance + 40 dB amp gain – 35 dB/m AF – 8 dB cable loss. • Note that 20 Log(Xstd/Xsite) = 20 Log 3/0.3 = 20 dB Page 28 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 5. Radiated Emissions. PM5 Maximum of Vertical Polarization FCC IR Limit Page 29 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 5. Radiated Emissions. PM5 Maximum of Horizontal Polarization FCC IR Limit Page 30 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com

Serial No. GM214045f Concept2, Inc. FCC ID: J2MPM5 X. Measurement Results Cont'd: 6. Exposure Evaluation. The analysis below compares the measured power to the maximum permissible exposure limit for general population with uncontrolled access. The PM5 can be used continuously; no special averaging time or limit relaxations are employed. Maximum peak available power is used in calculations. Unit Frequency: 2.4 GHz Unit Maximum Average Power .001 Watt available (-4 dBm from design) Standard User Weight: 100 kg Specific Absorption Rate (SAR) Limit for whole-body: 0.08 W/kg Specific Absorption Rate (SAR) Limit for one-gram tissue volume: 1.6 W/kg SAR Whole body = .001 W/100 kg = 0.00001 W/kg for PM5 SAR 1g tissue = .001 W/.001 kg * = 1 W/kg for PM5 In addition per IEEE C95.1 paragraph 6.10 (2): low power devices are unlikely to expose users in excess of the criteria when power is less than or equal to: Pmax = 1.4 * (450/f) Watts where f is in MHz. Pmax is significantly greater than the power available at the PM5: Pmax = 1.4 * (450/2400) = 0.26 W. Page 31 of 31 GME GME, Inc. • 219 Blake Roy Road • Middlebury, VT 05753 • Tel: 802-388-3390 • gmelectro.com


Document Created: 4690-11-05 00:00:00
Document Modified: 4690-11-05 00:00:00
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC