Test Report

FCC ID: IYZSK1

Test Report

Download: PDF
FCCID_4429691

Report on the FCC and IC Testing of the Marquardt GmbH Model: SK1 In accordance with FCC 47 CFR Part 15C and ISED Canada RSS-210 and ISED Canada RSS- GEN Prepared for: Marquardt GmbH Schloßstrasse 16 78604 Rietheim-Weilheim Germany FCC ID: IYZSK1 IC: 2701A-SK1 COMMERCIAL-IN-CONFIDENCE Date: 2019-09-02 Document Number: TR-64038-67571-02 | Issue: 01 RESPONSIBLE FOR NAME DATE SIGNATURE Project Management Michael Ingerl 2019-09-02 Authorised Signatory Markus Biberger 2019-09-02 Signatures in this approval box have checked this document in line with the requirements of TÜV SÜD Product Service document control rules. ENGINEERING STATEMENT The measurements shown in this report were made in accordance with the procedures described on test pages. All reported testing was carried out on a sample equipment to demonstrate limited compliance with FCC 47 CFR Part 15C and ISED Canada RSS-210 and ISED Canada RSS-GEN. The sample tested was found to comply with the requirements defined in the applied rules. RESPONSIBLE FOR NAME DATE SIGNATURE Testing Michael Ingerl 2019-09-02 Laboratory Accreditation Laboratory recognition ISED Canada test site registration DAkkS Reg. No. D-PL-11321-11-02 Registration No. BNetzA-CAB-16/21-15 3050A-2 EXECUTIVE SUMMARY A sample of this product was tested and found to be compliant with FCC 47 CFR Part 15C, ISED Canada RSS-210 and ISED Canada RSS-GEN:2016, Issue 09 (08-2016) and Issue 04 (11-2014). DISCLAIMER AND COPYRIGHT This non-binding report has been prepared by TÜV SÜD Product Service with all reasonable skill and care. The document is confidential to the potential Client and TÜV SÜD Product Service. No part of this document may be reproduced without the prior written approval of TÜV SÜD Product Service. © 2019 TÜV SÜD Product Service. ACCREDITATION Our BNetzA Accreditation does not cover opinions and interpretations and any expressed are outside the scope of our BNetzA Accreditation. Results of tests not covered by our BNetzA Accreditation Schedule are marked NBA (Not BNetzA Accredited). Trade Register Munich Managing Directors: Phone: +49 (0) 9421 55 22-0 TÜV SÜD Product Service GmbH HRB 85742 Dr. Peter Havel (CEO) Fax: +49 (0) 9421 55 22-99 VAT ID No. DE129484267 Dr. Jens Butenandt www.tuev-sued.de Äußere Frühlingstraße 45 Information pursuant to Section 2(1) 94315 Straubing DL-InfoV (Germany) at Germany www.tuev-sued.com/imprint TÜV SÜD Product Service

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE Contents 1 Report Summary .........................................................................................................................2 1.1 Report Modification Record ...........................................................................................................2 1.2 Introduction ....................................................................................................................................2 1.3 Brief Summary of Results .............................................................................................................3 1.4 Product Information .......................................................................................................................4 1.5 Deviations from the Standard ........................................................................................................4 1.6 EUT Modification Record ..............................................................................................................5 1.7 Test Location .................................................................................................................................5 2 Test Details ..................................................................................................................................6 2.1 Field Strength of any Emission .....................................................................................................6 2.2 20 dB Bandwidth ........................................................................................................................ 18 2.3 Switch off time ............................................................................................................................ 21 2.4 Restricted Band Edges............................................................................................................... 23 2.5 Exposure of Humans to RF Fields and SAR exclusion threshold .............................................. 25 3 Measurement Uncertainty ....................................................................................................... 30 COMMERCIAL-IN-CONFIDENCE Page 1 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 1 Report Summary 1.1 Report Modification Record Alterations and additions to this report will be issued to the holders of each copy in the form of a complete document. Issue Description of Change Date of Issue 1 First Issue 2019-09-02 Table 1 1.2 Introduction Applicant Marquardt GmbH Manufacturer Marquardt Switches (Shanghai) Co., Ltd. Model Number(s) SK1 Serial Number(s) --- Software Version --- Number of Samples Tested 1 Test Specification/Issue/Date FCC 47 CFR Part 15C, ISED Canada RSS-210 and ISED Canada RSS-GEN:2016, Issue 09 (08-2016) and Issue 04 (11-2014), FCC rule Part 2.1093, KDB 447498 D01, RSS- 102 Issue 5 Test Plan/Issue/Date --- Order Number 6200359433 Date of Receipt of EUT 2019-08-05 Start of Test 2019-08-21 Finish of Test 2019-08-28 Name of Engineer(s) Michael Ingerl Related Document(s) ANSI C63.10 (2013) ANSI C63.4: 2014 COMMERCIAL-IN-CONFIDENCE Page 2 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 1.3 Brief Summary of Results A brief summary of the tests carried out in accordance with FCC 47 CFR Part 15C and ISED Canada RSS-210, ISED Canada RSS-GEN, FCC rule Part 2.1093, KDB 447498 D01 is shown below. Section Specification Clause Test Description Result Comments/Base Standard Configuration and Mode: Battery Powered 3 V – Transmitting continuously 2.1 15.209, 4.3 and 6.13 Field Strength of any Emission Pass ANSI C63.10 (2013) 2.2 15.215 (c), N/A and 20 dB Bandwidth Pass ANSI C63.10 (2013) 6.6 2.3 15.231 (a) Switch off time Pass ANSI C63.10 (2013) 2.4 15.205, 4.1 and 8.10 Restricted Band Edges Pass ANSI C63.10 (2013) 2.5 15.107 and 6.1 Exposure of Humans to RF Fields and SAR exclusion threshold Pass ANSI C63.4: 2014 Table 2 COMMERCIAL-IN-CONFIDENCE Page 3 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 1.4 Product Information 1.4.1 Technical Description Equipment characteristics Type designation: SK1 Type of equipment: Passive entry car key Operating Frequency: 433.92 MHz Number of RF channels: 1 Modulation: 2-FSK Modulation Content: Digital data Data Rate: 5 kBit/s; 20 kBit/s Antenna: PCB loop antenna Standby mode: Not Applicable Power supply: Battery supply Nominal: 3V Nominal frequency: DC 1.5 Deviations from the Standard none COMMERCIAL-IN-CONFIDENCE Page 4 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 1.6 EUT Modification Record The table below details modifications made to the EUT during the test programme. The modifications incorporated during each test are recorded on the appropriate test pages. Date Modification Modification State Description of Modification still fitted to EUT Modification Fitted By Fitted 0 As supplied by the customer Not Applicable Not Applicable Table 3 1.7 Test Location TÜV SÜD Product Service conducted the following tests at our Straubing Test Laboratory. Test Name Name of Engineer(s) Configuration and Mode: Battery Powered 3 V – Transmitting continuously Field Strength of any Emission Michael Ingerl 20 dB Bandwidth Michael Ingerl Switch off time Michael Ingerl Restricted Band Edges Michael Ingerl Exposure of Humans to RF Fields and SAR Michael Ingerl exclusion threshold Table 4 Office Address: Äußere Frühlingstraße 45 94315 Straubing Germany COMMERCIAL-IN-CONFIDENCE Page 5 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 2 Test Details 2.1 Field Strength of any Emission 2.1.1 Specification Reference FCC 47 CFR Part 15C, ISED Canada RSS-210 and ISED Canada RSS-GEN, Clause 15.209, 4.3 and 6.13 2.1.2 Equipment Under Test and Modification State SK1, S/N: --- - Modification State 0 2.1.3 Date of Test 2019-08-21 2.1.4 Test Method This test was performed in accordance with ANSI C63.10, clause 6.3, 6.4 and 6.5. and ISED Canada RSS-Gen clause 6.13. Measurements were made at a distance of 3 m. The limit lines shown on the plot were extrapolated from either 300 m or 30 m to the measurement distance of 3 m in accordance with ANSI C63.10 Clause 6.4.4.2. For any emissions detected within 20 dB of the limit, a final measurement was made and recorded in the table below. The detector used for these measurements was a quasi-peak detector except for emissions within the bands 9 kHz to 90 kHz and 110 kHz to 490 kHz where a CISPR average detector was used. 2.1.5 Environmental Conditions Ambient Temperature 21.0 °C Relative Humidity 31.0 % COMMERCIAL-IN-CONFIDENCE Page 6 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 2.1.6 Test Results Battery Powered 3 V – Transmitting continuously 1. Orthogonal axis 130 120 110 100 90 80 70 Level in dB µV/m 60 50 40 30 20 10 0 -10 9k 20 30 50 100 k 200 300 500 1M 2M 3M 5M 10M 20 30M P re view R esult 1-QP K FC C 15.20 9 mag (10 m) Fin al_Res ult QP K Fin al_Res ult CA V COMMERCIAL-IN-CONFIDENCE Page 7 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 80 75 70 65 60 55 50 45 Level in dB µV/m 40 35 30 25 20 15 10 5 0 30M 50 60 80 100 M 200 300 400 500 800 1G P re view R esult 1H-P K+ P re view R esult 1V-P K+ FC C 15.20 9 Fin al_Res ult P K + Final Results 1: Frequency MaxPeak Limit Margin Meas. Bandwidth Pol Azimuth Corr. Comment Time MHz dBµV/m dBµV/m dB ms kHz deg dB/m 433.908000 76.83 80.80 3.97 2.5 100.000 V 91.0 -16 Fundamental 867.886000 38.75 46.00 7.25 2.5 100.000 V 115.0 -10 --- COMMERCIAL-IN-CONFIDENCE Page 8 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 80 75 70 65 60 55 50 Level in dB µV/m 45 40 35 30 25 20 15 10 5 0 1G 2G 3G 4G 5G P re view R esult 2 V-A V G P re view R esult 1V-P K+ P re view R esult 2 H-A V G P re view R esult 1H-P K+ FC C 15.20 9 P K FC C 15.20 9 A V Fin al_Res ult P K + Fin al_Res ult A V G COMMERCIAL-IN-CONFIDENCE Page 9 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 2. Orthogonal axis 130 120 110 100 90 80 70 Level in dB µV/m 60 50 40 30 20 10 0 -10 9k 20 30 50 100 k 200 300 500 1M 2M 3M 5M 10M 20 30M P re view R esult 1-QP K FC C 15.20 9 mag (10 m) Fin al_Res ult QP K Fin al_Res ult CA V COMMERCIAL-IN-CONFIDENCE Page 10 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 80 75 70 65 60 55 50 45 Level in dB µV/m 40 35 30 25 20 15 10 5 0 30M 50 60 80 100 M 200 300 400 500 800 1G P re view R esult 1H-P K+ P re view R esult 1V-P K+ FC C 15.20 9 Fin al_Res ult P K + Final Results 1: Frequency MaxPeak Limit Margin Meas. Bandwidth Pol Azimuth Corr. Comment Time MHz dBµV/m dBµV/m dB ms kHz deg dB/m 433.908000 75.60 80.80 5.20 2.5 100.000 H 120.0 -16 Fundamental 867.886000 38.50 46.00 7.50 2.5 100.000 H 110.0 -10 --- COMMERCIAL-IN-CONFIDENCE Page 11 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 80 75 70 65 60 55 50 Level in dB µV/m 45 40 35 30 25 20 15 10 5 0 1G 2G 3G 4G 5G P re view R esult 2 V-A V G P re view R esult 1V-P K+ P re view R esult 2 H-A V G P re view R esult 1H-P K+ FC C 15.20 9 P K FC C 15.20 9 A V Fin al_Res ult P K + Fin al_Res ult A V G COMMERCIAL-IN-CONFIDENCE Page 12 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 3. Orthogonal axis 130 120 110 100 90 80 70 Level in dB µV/m 60 50 40 30 20 10 0 -10 9k 20 30 50 100 k 200 300 500 1M 2M 3M 5M 10M 20 30M P re view R esult 1-QP K FC C 15.20 9 mag (10 m) Fin al_Res ult QP K Fin al_Res ult CA V COMMERCIAL-IN-CONFIDENCE Page 13 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 80 75 70 65 60 55 50 45 Level in dB µV/m 40 35 30 25 20 15 10 5 0 30M 50 60 80 100 M 200 300 400 500 800 1G P re view R esult 1H-P K+ P re view R esult 1V-P K+ FC C 15.20 9 Fin al_Res ult P K + Final Results 1: Frequency MaxPeak Limit Margin Meas. Bandwidth Pol Azimuth Corr. Comment Time MHz dBµV/m dBµV/m dB ms kHz deg dB/m 433.908000 75.64 80.80 5.16 2.5 100.000 V 289.0 -16 Fundamental 867.886000 35.61 46.00 10.39 2.5 100.000 V 279.0 -10 --- COMMERCIAL-IN-CONFIDENCE Page 14 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 80 75 70 65 60 55 50 Level in dB µV/m 45 40 35 30 25 20 15 10 5 0 1G 2G 3G 4G 5G P re view R esult 2 V-A V G P re view R esult 1V-P K+ P re view R esult 2 H-A V G P re view R esult 1H-P K+ FC C 15.20 9 P K FC C 15.20 9 A V Fin al_Res ult P K + Fin al_Res ult A V G COMMERCIAL-IN-CONFIDENCE Page 15 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE FCC 47 CFR Part 15, Limit Clause 15.209 Frequency (MHz) Field Strength (µV/m) Measurement Distance (m) 0.009 to 0.490 2400/F (kHz) 300 0.490 to 1.705 24000/F (kHz) 30 1.705 to 30 30 30 30 to 88 100** 3 88 to 216 150** 3 216 to 960 200** 3 Above 960 500 3 Table 5 - FCC Limit NOTE: The level of any unwanted emissions from an intentional radiator operating under these general provisions shall not exceed the level of the fundamental emission. ISED Canada RSS-210, Limit Clause 4.4 Under no circumstance shall the level of any unwanted emissions exceed the level of the fundamental emissions. ISED Canada RSS-Gen, Limit Clause 8.9 Frequency (MHz) Field Strength (µV/m) Measurement Distance (m) 0.009 to 0.490 2400/F (kHz) 300 0.490 to 1.705 24000/F (kHz) 30 1705 to 30 30 30 Table 6 - IC Limit, Below 30 MHz Frequency (MHz) Field Strength (µV/m at 3 metres) 30 to 88 100 88 to 216 150 216 to 960 200 Above 960 500 Table 7 - IC Limit, Above 30 MHz COMMERCIAL-IN-CONFIDENCE Page 16 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 2.1.7 Test Location and Test Equipment Used This test was carried out in Semi anechoic room - cabin no. 8. Calibration Instrument Manufacturer Type No TE No Period Calibration Due (months) Loop Antenna Rohde & Schwarz HFH2-Z2 18876 36 2022-08-31 TRILOG Antenna (4db) Schwarzbeck VULB 9162 20116 36 2022-01-31 Horn antenna Rohde & Schwarz HF907 19933 24 2021-07-31 EMI test receiver Rohde & Schwarz ESW26 28268 12 2020-06-30 EMC measurement Rohde & Schwarz EMC32-ME+ 19719 N/A N/A software Table 8 TU - Traceability Unscheduled O/P Mon – Output Monitored using calibrated equipment N/A - Not Applicable COMMERCIAL-IN-CONFIDENCE Page 17 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 2.2 20 dB Bandwidth 2.2.1 Specification Reference FCC 47 CFR Part 15C, ISED Canada RSS-210 and ISED Canada RSS-GEN, Clause 15.215 (c), N/A and 6.6 2.2.2 Equipment Under Test and Modification State SK1, S/N: --- - Modification State 0 2.2.3 Date of Test 2019-08-28 2.2.4 Test Method The test was performed in accordance with ANSI C63.10, clause 6.9.1. 2.2.5 Environmental Conditions Ambient Temperature 20.0 °C Relative Humidity 31.0 % 2.2.6 Test Results Battery Powered 3 V – Transmitting continuously Frequency (MHz) 20 dB Bandwidth 99% Occupied FLOWER (MHz) FUPPER (MHz) (kHz) Bandwidth (kHz) 433.92 159.45 161.76 433.84 434.00 Table 9 COMMERCIAL-IN-CONFIDENCE Page 18 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 20 dB Bandwidth 99% Occupied Bandwidth COMMERCIAL-IN-CONFIDENCE Page 19 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE FCC 47 CFR Part 15, Limit Clause 15.215 (c) and ISED Canada RSS 210 and ISED Canada RSS GEN, Limit Clause The OBW shall not be wider than 0.25 % of the center frequency, here maximum 1.0848 MHz. 2.2.7 Test Location and Test Equipment Used This test was carried out in a non-shielded room. Calibration Instrument Manufacturer Type No TE No Period Calibration Due (months) Spectrum Analyzer Rohde & Schwarz FSV40 20219 12 2020-01-31 Climatic test chamber ESPEC PL-2J 18843 24 2020-03-31 Table 10 TU - Traceability Unscheduled O/P Mon – Output Monitored using calibrated equipment N/A - Not Applicable COMMERCIAL-IN-CONFIDENCE Page 20 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 2.3 Switch off time 2.3.1 Specification Reference FCC 47 CFR Part 15C, ISED Canada RSS-210 and ISED Canada RSS-GEN, Clause 15.231 (a) 2.3.2 Equipment Under Test and Modification State SK1, S/N: --- - Modification State 0 2.3.3 Date of Test 2019-08-28 2.3.4 Test Method --- 2.3.5 Environmental Conditions Ambient Temperature 20.0 °C Relative Humidity 31.0 % 2.3.6 Test Results Battery Powered 3 V – Transmitting continuously Switch off time Limit 765 ms 5s COMMERCIAL-IN-CONFIDENCE Page 21 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE FCC 47 CFR Part 15, Limit Clause 15.231 and ISED Canada RSS-GEN A manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released. 2.3.7 Test Location and Test Equipment Used This test was carried out in a non-shielded room. Calibration Instrument Manufacturer Type No TE No Period Calibration Due (months) Spectrum Analyzer Rohde & Schwarz FSV40 20219 12 2020-01-31 Table 11 TU - Traceability Unscheduled O/P Mon – Output Monitored using calibrated equipment N/A - Not Applicable COMMERCIAL-IN-CONFIDENCE Page 22 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 2.4 Restricted Band Edges 2.4.1 Specification Reference FCC 47 CFR Part 15C, ISED Canada RSS-210 and ISED Canada RSS-GEN, Clause 15.205, 4.1 and 8.10 2.4.2 Equipment Under Test and Modification State SK1, S/N: --- - Modification State 0 2.4.3 Date of Test 2019-08-21 2.4.4 Test Method This test was performed in accordance with ANSI C63.10, clause 11.13.1. Plots for average measurements were taken in accordance with ANSI C63.10 clause 4.1.4.2.3. Final average measurements were taken in accordance with ANSI C63.10 clause 4.1.4.2.2. 2.4.5 Environmental Conditions Ambient Temperature 21.0 °C Relative Humidity 31.0 % 2.4.6 Test Results Battery Powered 3 V – Transmitting continuously See chapter 2.1 for results. COMMERCIAL-IN-CONFIDENCE Page 23 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE FCC 47 CFR Part 15, Limit Clause 15.205 Peak (dBµV/m) Average (dBµV/m) Restricted Bands of Operation 74 54 Table 12 ISED Canada RSS-GEN, Limit Clause 8.9 Frequency (MHz) Field Strength (µV/m at 3 metres) 30-88 100 88-216 150 216-960 200 Above 960* 500 Table 13 *Unless otherwise specified, for all frequencies greater than 1 GHz, the radiated emission limits for licence-exempt radio apparatus stated in applicable RSSs (including RSS-Gen) are based on measurements using a linear average detector function having a minimum resolution bandwidth of 1 MHz. If an average limit is specified for the EUT, then the peak emission shall also be measured with instrumentation properly adjusted for such factors as pulse desensitization to ensure the peak emission is less than 20 dB above the average limit. 2.4.7 Test Location and Test Equipment Used This test was carried out in Semi anechoic room - cabin no. 8. Calibration Instrument Manufacturer Type No TE No Period Calibration Due (months) Loop Antenna Rohde & Schwarz HFH2-Z2 18876 36 2022-08-31 TRILOG Antenna (4db) Schwarzbeck VULB 9162 20116 36 2022-01-31 Horn antenna Rohde & Schwarz HF907 19933 24 2021-07-31 EMI test receiver Rohde & Schwarz ESW26 28268 12 2020-06-30 EMC measurement Rohde & Schwarz EMC32-ME+ 19719 N/A N/A software Table 14 TU - Traceability Unscheduled O/P Mon – Output Monitored using calibrated equipment N/A - Not Applicable COMMERCIAL-IN-CONFIDENCE Page 24 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 2.5 Exposure of Humans to RF Fields and SAR exclusion threshold 2.5.1 Specification Reference IC RSS-GEN Issue 4, section 3.2 and IC RSS-102, Issue 5, section 2.5 and KDB 447498 D01 V06, section 4.3.1 a) 2.5.2 Guide IC RSS-102 Issue 5, section 2.5 2.5.3 Equipment Under Test and Modification State SK1, S/N: --- - Modification State 0 2.5.4 Date of Test 2019-08-27 2.5.5 Test Results COMMERCIAL-IN-CONFIDENCE Page 25 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE Declared by Exemption Applicable Measured applicant Exposure of Humans to RF Fields The antenna is detachable The conducted output power (CP in watts) is measured at the antenna connector: CP = ................ W The effective isotropic radiated power (EIRP in watts) is calculated using the numerical antenna gain: G = ................ EIRP = G  CP  EIRP = ................ W the field strength1 in V/m: FS = ................ V/m ( FS  D) 2 EIRP =  EIRP = ................ W 30 with: Distance between the antennas D = ................ m in m: not detachable A field strength measurement is used to determine the effective isotropic radiated power (EIRP in watts) given by: ( FS  D) 2 EIRP =  EIRP = 8.82 μW 30 with: Field strength in V/m: FS = 0.0054 Distance between the two antennas in m: D =3 Selection of output power The output power TP is the higher of the conducted or effective isotropic radiated power (e.i.r.p.): TP = 8.82 μW 1 The conversion formula is valid only for properly matched antennas. In other cases the transmitter output power may have to be measured by a terminated measurement when applying the exemption clauses. If an open area test site is used for field strength measurement, the effect due to the metal ground reflecting plane should be subtracted from the maximum field strength value in order to reference it to free space, before calculating TP. COMMERCIAL-IN-CONFIDENCE Page 26 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE Declared by Exemption Applicable Measured applicant Exposure of Humans to RF Fields (continued) Separation distance between the user and the transmitting device is less than or equal to 20 cm greater than 20 cm Transmitting device is in the vicinity of the human head body-worn SAR evaluation SAR evaluation is required if the separation distance between the user and/or bystander and the antenna and/or radiating element of the device is less than or equal to 20 cm, except when the device operates at or below the applicable output power level (adjusted for tune-up tolerance) for the specified separation distance defined in the table. For controlled use devices where the 8 W/kg for 1 gram of tissue applies, the exemption limits for routine evaluation in the table are multiplied by a factor of 5. For limb-worn devices where the 10 gram value applies, the exemption limits for routine evaluation in the table are multiplied by a factor of 2.5. If the operating frequency of the device is between two frequencies located in the table, linear interpolation shall be applied for the applicable separation distance. For test separation distance less than 5 mm, the exemption limits for a separation distance of 5 mm can be applied to determine if a routine evaluation is required. For medical implants devices, the exemption limit for routine evaluation is set at 1 mW. The output power of a medical implants device is defined as the higher of the conducted or e.i.r.p to determine whether the device is exempt from the SAR evaluation. Frequency Exemption limits (mW)2 at separation distance of (MHz) ≥50 mm ≤5 mm 10 mm 15 mm 20 mm 25 mm 30 mm 35 mm 40 mm 45 mm ≤300 3 71 101 132 162 193 223 254 284 315 345 450 52 70 88 106 123 141 159 177 195 213 835 17 30 42 55 67 80 92 105 117 130 1900 7 10 18 34 60 99 153 225 316 431 2450 4 7 15 30 52 83 123 173 235 309 3500 2 6 16 32 55 86 124 170 225 290 5800 1 6 15 27 41 56 71 85 97 106 Carrier frequency: f = 433.92 MHz Distance: d = 5 mm Transmitter output power: TP = 8.82 μW Limit: TPlimit = 54 mW SAR evaluation is documented in test report no. … 2 The excemption limit in the table are based on measurements and simulations on half-wave dipole antennas at separaton distances of 5 mm to 25 mm from a flat phantom, providing a SAR value of approximately 0.4 W/kg for 1 g of tissue. For low frequencies (300 MHz to 835 MHz), the exemption limits are derived from alinear fit. For high frequencies (1900 MHz and above), the exemption limits are derived from athird order polynomial fit. 3 Transmitters operating between 3 kHz and 10 MHz, meeting the exemption from routine SAR evaluation, shall demonstrate compliance to the instantaneous limits in IC RSS-102, issue 5, section 4. COMMERCIAL-IN-CONFIDENCE Page 27 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE Specifications: RSS-102, Issue 5, Section 4, Table 4, Uncontrolled Environment SPR-002, Issue 1 Operation mode: Battery Powered 3 V – Transmitting continuously Comment: --- Test procedure: IEC 62236-1, Section 4.2 “Measurement to show accordance to the reference levels” Test distance: Direct contact to EUT Limit: Frequency Electric Field Magnetic Field Peference Range (MHz) (V/mrms) (A/mrms) Periode (min) 10-20 27.46 0.0728 6 300-6000 3.142 f0.3417 0.008335 f0.3417 6 f in MHz Test positions: All surfaces: The antenna was moved all over the equipment under test using a test distance as stated above. Measured maximum value Maximum Limit at 433.92 MHz Margin to reference value (V/m) (V/m) (V/m) 2.18 25.03 22.85 Measured maximum value Maximum Limit at 433.92 MHz Margin to reference value (A/m) (A/m) (A/m) 0.0058 0.0664 0.0606 COMMERCIAL-IN-CONFIDENCE Page 28 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE SAR Exclusion threshold Maximum Radiated Fields Strength: 76.83 dBµV/m (see chapter 2.1.6 of this test report) (at 3 m distance and 433.92 MHz) Calculated Equivalent Radiated Power: 8.82 μW (e.i.r.p.) < 10 μW Minimum separation distance: 5 mm (≤ 50 mm) 1-g numeric threshold: (100 μW / 5 mm) · √(0.43392 GHz) = 0.013 1-g numeric threshold limit: 3.0 Note 1: For test distances below 5 mm according to 4.3.1 a) the test distance is fixed to 5 mm. ( FS  D ) 2 EIRP = 30 2.5.6 Test Location and Test Equipment Used This test was carried out in a non-shielded room. Calibration Instrument Manufacturer Type No TE No Period Calibration Due (months) Electromagnetic radiation Narda Safety EMR-200 19590 36 2019-10-31 meter Electric field probe Narda Safety Type 8.3 19591 36 2019-10-31 Magnetic field probe Narda Safety Type 12.1 19592 36 2019-10-31 Exposure level tester Narda Safety ELT-400 19725 24 2020-06-30 Table 15 COMMERCIAL-IN-CONFIDENCE Page 29 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE 3 Measurement Uncertainty For a 95% confidence level, the measurement uncertainties for defined systems are: Radio Testing Expanded Test Name kp Note Uncertainty Occupied Bandwidth 2.0 ±1.14 % 2 RF-Frequency error 1.96 ±1 · 10-7 7 RF-Power, conducted carrier 2 ±0.079 dB 2 RF-Power uncertainty for given BER 1.96 +0.94 dB / -1.05 7 RF power, conducted, spurious emissions 1.96 +1.4 dB / -1.6 dB 7 RF power, radiated 25 MHz – 4 GHz 1.96 +3.6 dB / -5.2 dB 8 1 GHz – 18 GHz 1.96 +3.8 dB / -5.6 dB 8 18 GHz – 26.5 GHz 1.96 +3.4 dB / -4.5 dB 8 40 GHz – 170 GHz 1.96 +4.2 dB / -7.1 dB 8 Spectral Power Density, conducted 2.0 ±0.53 dB 2 Maximum frequency deviation 300 Hz – 6 kHz 2 ±2,89 % 2 6 kHz – 25 kHz 2 ±0.2 dB 2 Maximum frequency deviation for FM 2 ±2,89 % 2 Adjacent channel power 25 MHz – 1 GHz 2 ±2.31 % 2 Temperature 2 ±0.39 K 4 (Relative) Humidity 2 ±2.28 % 2 DC- and low frequency AC voltage DC voltage 2 ±0.01 % 2 AC voltage up to 1 kHz 2 ±1.2 % 2 Time 2 ±0.6 % 2 Table 16 COMMERCIAL-IN-CONFIDENCE Page 30 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE Radio Interference Emission Testing Expanded Test Name kp Note Uncertainty Conducted Voltage Emission 9 kHz to 150 kHz (50/50µH AMN) 2 ± 3.8 dB 1 150 kHz to 30 MHz (50/50µH AMN) 2 ± 3.4 dB 1 100 kHz to 200 MHz (50/5µH AMN) 2 ± 3.6 dB 1 Discontinuous Conducted Emission 9 kHz to 150 kHz (50/50µH AMN) 2 ± 3.8 dB 1 150 kHz to 30 MHz (50/50µH AMN) 2 ± 3.4 dB 1 Conducted Current Emission 9 kHz to 200 MHz 2 ± 3.5 dB 1 Magnetic Fieldstrength 9 kHz to 30 MHz (with loop antenna) 2 ± 3.9 dB 1 9 kHz to 30 MHz (large-loop antenna 2 m) 2 ± 3.5 dB 1 Radiated Emission Test distance 1 m (ALSE) 9 kHz to 150 kHz 2 ± 4.6 dB 1 150 kHz to 30 MHz 2 ± 4.1 dB 1 30 MHz to 200 MHz 2 ± 5.2 dB 1 200 MHz to 2 GHz 2 ± 4.4 dB 1 2 GHz to 3 GHz 2 ± 4.6 dB 1 Test distance 3 m 30 MHz to 300 MHz 2 ± 4.9 dB 1 300 MHz to 1 GHz 2 ± 5.0 dB 1 1 GHz to 6 GHz 2 ± 4.6 dB 1 Test distance 10 m 30 MHz to 300 MHz 2 ± 4.9 dB 1 300 MHz to 1 GHz 2 ± 4.9 dB 1 Radio Interference Power 30 MHz to 300 MHz 2 ± 3.5 dB 1 Harmonic Current Emissions 4 Voltage Changes, Voltage Fluctuations and Flicker 4 Table 17 COMMERCIAL-IN-CONFIDENCE Page 31 of 32

Document Number: TR-64038-67571-02 | Issue: 01 COMMERCIAL-IN-CONFIDENCE Immunity Testing Expanded Test Name kp Note Uncertainty Electrostatic Discharges 4 Radiated RF-Field Pre-calibrated field level 2 +32.2 / -24.3 % 5 Dynamic feedback field level 2.05 +21.2 / -17.5 % 3 Electrical Fast Transients (EFT) / Bursts 4 Surges 4 Conducted Disturbances, induced by RF-Fields via CDN 2 +15.1 / -13.1 % 6 via EM clamp 2 +42.6 / -29.9 % 6 via current clamp 2 +43.9 / -30.5 % 6 Power Frequency Magnetic Field 2 +20.7 / -17.1 % 2 Pulse Magnetic Field 4 Voltage Dips, Short Interruptions and Voltage Variations 4 Oscillatory Waves 4 Conducted Low Frequency Disturbances Voltage setting 2 ± 0.9 % 2 Frequency setting 2 ± 0.1 % 2 Electrical Transient Transmission in Road Vehicles 4 Table 18 Note 1: The expanded uncertainty reported according to CISPR 16-4-2:2003-11 is based on a standard uncertainty multiplied by a coverage factor of kp = 2, providing a level of confidence of p = 95.45% Note 2: The expanded uncertainty reported according to UKAS Lab 34 (Edition 1, 2002-08) is based on a standard uncertainty multiplied by a coverage factor of kp = 2, providing a level of confidence of p = 95.45% Note 3: The expanded uncertainty reported according to UKAS Lab 34 (Edition 1, 2002-08) is based on a standard uncertainty multiplied by a coverage factor of kp = 2.05, providing a level of confidence of p = 95.45% Note 4: It has been demonstrated that the used test equipment meets the specified requirements in the standard with at least a 95%confidence. Note 5: The expanded uncertainty reported according to IEC 61000-4-3 is based on a standard uncertainty multiplied by a coverage factor of kp = 2, providing a level of confidence of p = 95.45% Note 6: The expanded uncertainty reported according to IEC 61000-4-6 is based on a standard uncertainty multiplied by a coverage factor of kp = 2, providing a level of confidence of p = 95.45% Note 7: The expanded uncertainty reported according ETSI TR 100 028 V1.4.1 (all parts) to is based on a standard uncertainty multiplied by a coverage factor of kp = 1.96, providing a level of confidence of p = 95.45% Note 8: The expanded uncertainty reported according to ETSI TR 102 273 V1.2.1 (all parts) is based on a standard uncertainty multiplied by a coverage factor of kp = 1.96, providing a level of confidence of p = 95.45% COMMERCIAL-IN-CONFIDENCE Page 32 of 32


Document Created: 2019-09-05 19:50:47
Document Modified: 2019-09-05 19:50:47
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC