Test report Basis

FCC ID: IYZFBSB802

Test Report

Download: PDF
FCCID_859565

Test report no. 07004143 Page 1 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 DAT-P-225/96-02 Test Report acc. to the relevant standard 47 CFR Part 15 C – Intentional Radiators Measurement Procedure: ANSI C63.4 - 1992 relating to Marquardt GmbH FBSB802 ID-Geber Basis Measurement of Radio- Noise Emissions from Low- Voltage Electrical and Electronic Equipment Technical characteristics and test methods for radio equipment in the frequency range 9 kHz to 40 GHz m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 2 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 Manufacturer’s details Manufacturer Marquardt GmbH Manufacturer’s grantee code IYZ Manufacturer’s address Schloßstrasse 16 D-78604 Rietheim Weilheim Germany Phone : +49 7424 99 1960 Fax : +49 7424 99 2419 E- Mail: andreas.gaebler@marquardt.de Relevant standard used 47 CFR Part 15C - Intentional Radiators ANSI C63.4-1992 Test report prepared by Technical engineer Ralf Trepper m.dudde hochfrequenz-technik (laboratory) Rottland 5a 51429 Bergisch Gladbach Germany Phone: +49 2207 96890 Fax: +49 2207 968920 E-mail: m.duddelabor@dudde.com Equipment Under Test (EUT) Equipment category Transmitter Trade name Marquardt Type designation FBSB802 ID-Geber Basis Serial no. Batch number: 5203 Variants none m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 3 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 0 Test result CFR Report Requirements Test result Section Chapter Headline OK 15.203 10.1 Antenna requirement pass fail n.a. 15.231(b) 10.2 Field strength limits (fundamental) pass fail n.a. 15.205(b) 10.2 Radiated spurious emissions pass fail n.a. 15.209 15.231(a) 10.3 Periodic operation characteristics pass fail n.a. 15.231 (c) 10.4 20 dB bandwidth pass fail n.a. 15.201 (a) 10.5 Equipment authorization requirement pass fail n.a. 15.209 Test requirements kept yes no Signature (Technical engineer) ........................................ Ralf Trepper Signature (Manager) ....................................... Manfried Dudde m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 4 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 List of contents Page 0 Test result ............................................................................................................................................... 3 1 Test laboratory........................................................................................................................................ 6 2 Introduction ............................................................................................................................................ 6 3 Product ................................................................................................................................................... 7 4 Test schedule .......................................................................................................................................... 7 5 Product and measurement documentation................................................................................................ 8 6 Observations and comments.................................................................................................................... 8 7 Summary ................................................................................................................................................ 8 8 Conclusions ........................................................................................................................................... 9 9 Operation description.............................................................................................................................. 10 10.1 Antenna requirement ......................................................................................................................... 11 10.1.1 Regulation ...................................................................................................................................... 11 10.1.2 Result ............................................................................................................................................. 11 10.2 Radiated emissions ........................................................................................................................... 12 10.2.1 Regulation ...................................................................................................................................... 12 10.2.2 Test equipment ............................................................................................................................... 13 10.2.2.1 Test procedures............................................................................................................................ 13 10.2.3 Calculation of field strength limits.................................................................................................. 14 10.2.4 Calculation of average correction factor.......................................................................................... 14 10.2.5 Calculation of the field strengths .................................................................................................... 14 10.2.6 Results............................................................................................................................................ 15 10.3 Periodic operation characteristics ....................................................................................................... 18 10.3.1 Periodic operation........................................................................................................................... 18 10.3.1.1 Regulation ................................................................................................................................... 18 10.3.1.2 Result .......................................................................................................................................... 18 10.3.2 Manually operated transmitter deactivation .................................................................................... 18 10.3.2.1 Regulation ................................................................................................................................... 18 10.3.2.2 Result .......................................................................................................................................... 18 10.3.3 Automatically operated transmitter deactivation ............................................................................. 18 10.3.3.1 Regulation ................................................................................................................................... 18 10.3.3.2 Result .......................................................................................................................................... 18 10.3.4 Prohibition of periodic transmission ............................................................................................... 19 10.3.4.1 Regulation ................................................................................................................................... 19 10.3.4.2 Result .......................................................................................................................................... 19 10.3.5 Continuous transmission during an alarm condition........................................................................ 19 10.3.5.1 Regulation ................................................................................................................................... 19 10.3.5.2 Result .......................................................................................................................................... 19 10.4 Bandwidth ........................................................................................................................................ 20 10.4.1 Regulation ...................................................................................................................................... 20 10.4.2 Calculation of the 20 dB bandwidth limit ....................................................................................... 20 10.4.3 Test equipment ............................................................................................................................... 20 10.4.4 Test procedure ................................................................................................................................ 20 10.4.5 Test result ....................................................................................................................................... 21 10.5 Radiated emission............................................................................................................................. 22 10.5.1 Regulation ...................................................................................................................................... 22 10.5.2 Test equipment ............................................................................................................................... 23 10.5.3 Test procedures............................................................................................................................... 24 10.5.4 Calculation of field strength Section 15.209 below 30 MHz ........................................................... 25 10.5.5 Calculation of field strength Section 15.209 above 30 MHz ........................................................... 25 10.5.6 Calculation of the field strength ...................................................................................................... 26 m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 5 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 10.5.7 Calculation of Average Correction Factor....................................................................................... 26 11 Additional information to this test report ............................................................................................... 29 m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 6 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 1 Test laboratory Company name : m.dudde hochfrequenz-technik Street : Rottland 5a City : 51429 Bergisch Gladbach Country : Germany Laboratory : FCC Registration Number: 699717 This site has been fully described in a report submitted to the FCC, and renewed with letter dated July 12, 2005, Registration Number 699717. Phone : +49-2207-9689-0 Fax : +49-2207-9689-20 E-Mail : manfred.dudde@t-online.de Web : http://www.dudde.com 2 Introduction The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of m. dudde hochfrequenz - technik. This report contains the result of tests performed by m. dudde hochfrequenz - technik for the purpose of a type approval. The order for carrying out these tests has been placed by: Manufacturer Company name : Marquardt GmbH Address : Schloßstrasse 16 Postcode : D-78604 City/town : Rietheim-Weilheim Country : Germany Telephone : +49 7424 99 1960 Telefax : +49 7442 99 2419 E-Mail : andreas.gaebler@marquardt.de Date of order : 2007-03-22 References : Mr. Andreas Gäbler m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 7 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 3 Product Samples of the following apparatus were submitted for testing: Type of equipment : Transmitter Trademark : Marquardt Type designation : FBSB802 ID-Geber Basis Hardware version : FBSB802 ID-Geber Basis Serial number : Batch number: 5203 Software release : 0047 Power used : 3.00 VDC Frequency used : 315.00 MHz Generated or used frequencies : 32.768 kHz / 13.5672 MHz / 315.00 MHz ITU emission class : 95K0 F1D FCC ID : IYZFBSB802 4 Test schedule The tests were carried out in accordance with the specifications detailed in chapter 7 “Summary“ of this report at: - m. dudde hochfrequenz - technik, D-51429 Bergisch Gladbach The test sample was received on: - 2007-03-22 The tests were carried out in the following period of time: - 2007-05-02 - 2007-05-04 m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 8 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 5 Product and measurement documentation For issuing this report the following product documentation was used and the following annexes were created: Description Date Identifications External photographs of the Equipment Under Test 2007-05-18 Annex No. 1 Internal photographs of the Equipment Under Test 2007-05-18 Annex No. 2 Occupied bandwidth plot 2007-05-04 Annex No. 3 FCC ID label sample 2007-02-28 Annex No. 4 User Manual 2006-12-15 Annex No. 5 Test setup photos 2007-05-04 Annex No. 6 Block diagram 2007-03-28 Annex No. 7 Schematics 2006-12-18 Annex No. 8 Technical description 2007-03-28 Annex No. 9 Periodic operation characteristic 2007-05-04 Annex No. 10 The above mentioned documentation will be filed at m. dudde hochfrequenz - technik for a period of 10 years following the issue of this report. 6 Observations and comments 7 Summary The product is intended for the use in the following areas of application: Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the frequency range of 9 kHz to 40 GHz The samples were tested according to the following specification: 47 CFR Part 15 – Intentional Radiators, ANSI C63.4 - 1992 m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 9 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 8 Conclusions Samples of the apparatus were found to CONFORM WITH the specifications stated in chapter 7 "Summary" of this report. In the opinion of m. dudde hochfrequenz - technik, the samples satisfied all applicable requirements relating to the network interface types specified in chapter 7 "Summary". The results of the type tests as stated in this report are exclusively applicable to the product item as identified in this report. m. dudde hochfrequenz - technik does not accept any responsibility for the results stated in this report, with respect to the properties of product items not involved in these tests. This report consists of a main module, modules with test results and annexes listed in chapter 5: “Product documentation”. All pages have been numbered consecutively and bear the m. dudde hochfrequenz - technik logo, the report number and sub numbers. The total number of pages in this report is 30. Tester: Date : 2007-05-21 Name : Ralf Trepper Signature : Technical responsibility for area of testing: Date : 2007-05-21 Name : Manfried Dudde Signature : m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 10 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 9 Operation description 9.1 EUT details See Annex no. 5 (User Manual) 9.2 EUT configuration The Transmitter FBSB802 ID-Geber Basis operated in the continuous transmitting mode after pressing a bottom. To press the close or open bottom: the transmitter operated in CW mode To press the tailgate bottom: the transmitter operated in modulation mode 9.3 EUT measurement description The Transmitter FBSB802 ID-Geber Basis was tested in a typical fashion. During preliminary emission tests the Transmitter FBSB802 ID-Geber Basis was operated in the continuous transmitting mode for worst case emission mode investigation. Therefore, the final qualification testing was completed with Transmitter FBSB802 ID- Geber Basis operated in continuous modes. All tests were performed with the applicant’s typical voltage: 3.0 V DC In order to establish the maximum radiation, firstly, there have been viewed all orthogonal adjustments of the test samples, secondly the test ample have been rotated at all adjustments around the own axis between 0° and 360°, and thirdly, the antenna polarization between horizontal and vertical had been varied. m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 11 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 10.1 Antenna requirement 10.1.1 Regulation 15.203 An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of Part 15C. The manufacturer may design the unit so that the user can replace a broken antenna, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier current devices or to devices operated under the provisions of Sections 15.211, 15.213, 15.217, 15.219, or 15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional radiators which, in accordance with Section 15.31 (d), must be measured at the installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed so that the limits in this Part are not exceeded. 10.1.2 Result The equipment meets the requirements yes no n.a. Further test results are attached yes no page no: n.a x see page no. 29 m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 12 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 10.2 Radiated emissions 10.2.1 Regulation Test requirement: FCC CFR47, Part 15C, Test procedure: ANSI C63.4:1992 Fundamental frequency Field strength of fundamental Field strength of spurious emissions (MHz) (µV/m) (µV/m) 40.66 - 40.70 2,250 225 70-130 1,250 125 130-174 1,250 to 3,750 125 to 375 174-260 3,750 375 260-470 3,750 to 12,500 375 to 1,250 Above 470 12,500 1,250 ** Linear interpolations [Where F is the frequency in MHz, the formulas for calculating the maximum permitted fundamental field strengths are as follows: for the band 130-174 MHz, µV/m at 3 meters = 56.81818(F) - 6136.3636; for the band 260-470 MHz, µV/m at 3 meters = 41.6667(F) - 7083.3333. The maximum permitted unwanted emission level is 20 dB below the maximum permitted fundamental level.] (1) The above field strength limits are specified at a distance of 3 meters. The tighter limits apply at the band edges. (2) Intentional radiators operating under the provisions of this Section shall demonstrate compliance with the limits on the field strength of emissions, as shown in the above table, based on the average value of the measured emissions. As an alternative, compliance with the limits in the above table may be based on the use of measurement instrumentation with a CISPR quasi-peak detector. The specific method of measurement employed shall be specified in the application for equipment authorization. If average emission measurements are employed, the provisions in Section 15.35 for averaging pulsed emissions and for limiting peak emissions apply. Further, compliance with the provisions of Section 15.205 shall be demonstrated using the measurement instrumentation specified in that section. (3) The limits on the field strength of the spurious emissions in the above table are based on the fundamental frequency of the intentional radiator. Spurious emissions shall be attenuated to the average (or, alternatively, CISPR quasi-peak) limits shown in this table or to the general limits shown in Section 15.209, whichever limit permits higher field strength. Section 15.33 Frequency range of radiated measurements: (a) Unless otherwise noted in the specific rule section under which the equipment operates for an intentional radiator the spectrum shall be investigated from the lowest radio frequency signal generated in the device, without going below 9 kHz, up to at least the frequency shown in this paragraph: (1 ). If the intentional radiator operates below 10 GHz: to the tenth harmonic of the highest fundamental frequency or to 40 GHz, whichever is lower. m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 13 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 10.2.2 Test equipment Type Manufacturer/ Serial no. Last calibration Next calibration Model No. Receiver Hewlett Packard 3528U00990 2006/05 2008/05 Spectrum Analyzer (9 kHz –26.5 GHz) 8593E (171) Pre-amplifier Hewlett Packard 1726A00705 2006/03 2008/03 (100kHz - 1.3GHz) 8447 E (166a) Bilog antenna CHASE 1517 2003/09 2009/09 (30- 1000 MHz) CBL611A (167) Horn antenna Schwarzbeck 236 1998/01 2008/01 (0,86-8,5 GHz) BBHA 9120 A (284) 10.2.2.1 Test procedures The EUT and this peripheral (when additional equipment exists) are placed on a turn table which is 0.8m above the ground. The turn table would be allowed to rotate 360 degrees to determine the position of the maximum emission level. The test distance between the EUT and the receiving antenna are 3m. To find the maximum emission, the polarization of the receiving antenna are changed in horizontal and vertical polarization, the position of the EUT was changed in different orthogonal determinations. ANSI C63.4: 1992 Section 8 “Radiated Emissions Testing” Radiated emissions test characteristics Frequency range 30 MHz - 4,000 MHz Test distance 3 m* Test instrumentation resolution bandwidth 120 kHz (30 MHz - 1,000 MHz) 1 MHz (1000 MHz - 4,000 MHz) Receive antenna scan height 1m-4m Receive antenna polarization Vertical/horizontal *According to Section 15.31 (f) (1): At frequencies at or above 30 MHz, measurements may be performed at a distance other than what is specified provided: measurements are not made in the near field except where it can be shown that near field measurements are appropriate due to the characteristics of the device; and it can be demonstrated that the signal levels needed to be measured at the distance employed can be detected by the measurement equipment. When performing measurements at a distance other than that specified, the results shall be extrapolated to the specified distance using an extrapolation factor of 20dB/decade (inverse linear-distance for field strength measurements; inverse-linear-distance-squared for power density measurements). m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 14 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 10.2.3 Calculation of field strength limits For example: Transmitter working on 315 MHz Limit for average measurements → 41.6667*(315 MHz) – 7083.3333 = 6041.677µV/m = 75.6dBµV/m @3m Limit for peak measurements → Limit for average measurements + 20dB = 95.6dBµV/m @3m 10.2.4 Calculation of average correction factor The average correction factor is computed by analyzing the "worst case" on time in any 100msec time period and using the formula: Corrections Factor + 20*log (worst case on time/100msec). Analysis of the remote transmitter worst case on time in any 100msec time period is an on time of 50msec, therefore the correction factor is 20*log (50/100) = - 6 dB. The maximum correction factor to be applied is 20 dB per section 15.35 of the FCC rules. 10.2.5 Calculation of the field strengths The field strength is calculated by the following calculation: Corrected Level = Receiver Level + Correction Factor (without the use of a pre-amplifier) Corrected Level = Receiver Level + Correction Factor – Pre-Amplifier (with the use of a pre-amplifier) Receiver Level : Receiver reading without correction factors Correction Factor : Antenna factor + cable loss For example: The receiver reading is 32.7 dBµV. The antenna factor for the measured frequency is +2.5 dB (1/m) and the cable factor for the measured frequency is 0.71 dB, giving a field strength of 35.91dBµV/m. The 35.91dBµV/m value can be mathematically converted to its corresponding level in µV/m. Level in µV/m = Common Antilogarithm (35.91/20) = 39.8 For test distance other than what is specified, but fulfilling the requirements of Section 15.31 (f) (1) the field strength is calculated by adding additionally an extrapolation factor of 20 dB/decade (inverse linear distance for field strength measurements). m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 15 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 10.2.6 Results TRANSMITTER SPURIOUS RADIATION (Section 15.231(b)) Polarisation Antenna f Bandwidth Noted Test Correction Distance Level Limit Margin EUT height (MHz) (kHz) / receiver level distance factor extrapol. corrected / Type factor antenna of detector dBµV m dB dB dBµV/m dBµV/m dBµV/m cm 315.030 120, QPK 82.7 3 -7.5*5 0 75.2 75.6 0.4 V/V 150 630.060 120, QPK 47.8 3 -1.9* 5 0 45.9 55.6 9.7 V/V 150 945.090 120, QPK 39.1 3 +1.2* 5 0 40.3 55.6 15.3 V/V 180 1260.120 1000, AV 38.4 3 +1.3*6 0 39.7 55.6 15.9 V/V 120 1575.150 1000, AV 37.3 3 +2.8* 6 0 40.1 55.6 15.5 V/V 170 1890.180 1000, AV 43.0 3 +3.8* 6 0 46.8 55.6 8.8 V/V 130 2205.210 1000, AV 30.9 3 +7.8* 6 0 38.7 55.6 16.9 V/V 190 2520.240 1000, AV 29.6 3 +7.9* 6 0 37.5 55.6 18.1 V/V 130 2835.270 1000, AV 36.0 3 +9.6*6 0 45.6 55.6 10.0 V/V 130 3150.300 1000, AV 32.3 3 +11.3* 6 0 43.6 55.6 12.0 V/V 180 3465.330 1000, AV 24.6 3 +13.7* 6 0 38.3 55.6 17.3 V/V 100 3 Measurement uncertainty 4 dB Bandwidth = the measuring receiver bandwidth Remark: *1 noise floor noise level of the measuring instrument ≤ 3.5dBµV @ 3m distance (30 – 1,000 MHz) Remark: *2 noise floor noise level of the measuring instrument ≤ 4.5dBµV @ 3m distance (1,000 – 2,000 MHz) Remark: *3 noise floor noise level of the measuring instrument ≤ 10dBµV @ 3m distance (2,000 – 5,500 MHz) Remark: *4 noise floor noise level of the measuring instrument ≤ 14dBµV @ 3m distance (5,500 – 14,500 MHz) Remark: *5 for using a pre-amplifier in the range between 100 kHz and 1,000 MHz Remark: *6 for using a pre-amplifier in the range between 1.0 GHz and 18.0 GHz The equipment meets the requirements yes no n.a. Further test results are attached yes no n.a x see page no. 29 m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 16 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 TRANSMITTER SPURIOUS RADIATION (Section 15.231(b)) Polarisation Antenna f Bandwidth Noted Test Correction Distance Level Limit Margin EUT height (MHz) (kHz) / receiver level distance factor extrapol. corrected / Type factor antenna of detector dBµV m dB dB dBµV/m dBµV/m dBµV/m cm 315.030 120, QPK 77.2 3 -7.5*5 0 69.7 75.6 5.9 V/H 200 630.060 120, QPK 40.8 3 -1.9* 5 0 38.9 55.6 16.7 V/H 140 945.090 120, QPK 30.2 3 +1.2* 5 0 31.4 55.6 24.2 V/H 180 1260.120 1000, AV 28.9 3 +1.3*6 0 30.2 55.6 25.4 V/H 100 1575.150 1000, AV 32.9 3 +2.8* 6 0 35.7 55.6 19.9 V/H 110 1890.180 1000, AV 32.7 3 +3.8* 6 0 36.5 55.6 19.1 V/H 180 2205.210 1000, AV 30.1 3 +7.8*6 0 37.9 55.6 17.7 V/H 160 2520.240 1000, AV 29.4 3 +7.9* 6 0 37.3 55.6 18.3 V/H 200 2835.270 1000, AV 37.4 3 +9.6*6 0 47.0 55.6 8.6 V/H 180 3150.300 1000, AV 27.4 3 +11.3* 6 0 38.7 55.6 16.9 V/H 160 3465.330 1000, AV 25.2 3 +13.7* 6 0 38.9 55.6 16.7 V/H 150 3 Measurement uncertainty 4 dB Bandwidth = the measuring receiver bandwidth Remark: *1 noise floor noise level of the measuring instrument ≤ 3.5dBµV @ 3m distance (30 – 1,000 MHz) Remark: *2 noise floor noise level of the measuring instrument ≤ 4.5dBµV @ 3m distance (1,000 – 2,000 MHz) Remark: *3 noise floor noise level of the measuring instrument ≤ 10dBµV @ 3m distance (2,000 – 5,500 MHz) Remark: *4 noise floor noise level of the measuring instrument ≤ 14dBµV @ 3m distance (5,500 – 14,500 MHz) Remark: *5 for using a pre-amplifier in the range between 100 kHz and 1,000 MHz Remark: *6 for using a pre-amplifier in the range between 1.0 GHz and 18.0 GHz The equipment meets the requirements yes no n.a. Further test results are attached yes no n.a x see page no. 29 m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 17 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 TRANSMITTER SPURIOUS RADIATION ABOVE 30 MHz (Section 15.205, 15.209) AV Polaris. Antenna f Bandwidth Noted Test Correction Distance Level Limit Margin Correction EUT height (MHz) (kHz) receiver distance factor extrapol. corrected factor / Type level factor antenna of detector dBµV m dB dB dBµV/m dBµV/m dBµV/m dB cm 30.0000 100, AV ≤ 3.5 3 5 0 0 0.90 40.00 39.10 H,V/H,V 100-400 -2.60* 88.0000 100, AV ≤ 3.5 3 5 0 0 -7.30 40.00 47.30 H,V/H,V 100-400 -10.80* 216.0000 100, AV ≤ 3.5 3 5 0 0 -6.80 43.50 50.30 H,V/H,V 100-400 -10.30* 960.0000 100, AV ≤ 3.5 3 5 0 0 12.00 43.50 31.50 H,V/H,V 100-400 8.50* 1700.0000 1000, AV ≤ 4.5 3 6 0 0 8.30 54.00 45.70 H,V/H,V 100-400 3.80* 2250.0000 1000, AV ≤ 10 3 6 0 0 18.00 54.00 36.00 H,V/H,V 100-400 8.00* 4000.0000 1000, AV ≤ 10 3 6 0 0 18.40 54.00 35.60 H,V/H,V 100-400 8.40* 5000.0000 1000, AV ≤ 10 3 6 0 0 19.40 54.00 34.60 H,V/H,V 100-400 9.10* 7500.0000 1000, AV ≤ 14 3 6 0 0 26.90 54.00 27.10 H,V/H,V 100-400 12.9* 8300.0000 1000, AV ≤ 14 3 6 0 0 28.80 54.00 25.20 H,V/H,V 100-400 14.80* 9400.0000 1000, AV ≤ 14 3 6 0 0 30.00 54.00 24.00 H,V/H,V 100-400 16.00* 11000.0000 1000, AV ≤ 14 3 6 0 0 32.25 54.00 21.75 H,V/H,V 100-400 18.25* Measurement uncertainty 4 dB Bandwidth = the measuring receiver bandwidth Remark: *1 noise floor noise level of the measuring instrument ≤ 3.5dBµV @ 3m distance (30 – 1,000 MHz) Remark: *2 noise floor noise level of the measuring instrument ≤ 4.5dBµV @ 3m distance (1,000 – 2,000 MHz) Remark: *3 noise floor noise level of the measuring instrument ≤ 10dBµV @ 3m distance (2,000 – 5,500 MHz) Remark: *4 noise floor noise level of the measuring instrument ≤ 14dBµV @ 3m distance (5,500 – 14,500 MHz) Remark: *5 for using a pre-amplifier in the range between 100 kHz and 1,000 MHz Remark: *6 for using a pre-amplifier in the range between 1.0 GHz and 18.0 GHz The equipment meets the requirements yes no n.a. Further test results are attached yes no page no: n.a x see page no. 29 m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 18 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 10.3 Periodic operation characteristics 10.3.1 Periodic operation 10.3.1.1 Regulation 15.231 (a) The provisions of this Section are restricted to periodic operation within the band 40.66 40.70 MHz and above 70 MHz. Except as shown in paragraph (e) of this Section, the intentional radiator is restricted to the transmission of a control signal such as those used with alarm systems, door openers, remote switches, etc. Radio control of toys is not permitted. Continuous transmissions, such as voice or video, and data transmissions are not permitted. The prohibition against data transmissions does not preclude the use of recognition codes. Those codes are used to identify the sensor that is activated or to identify the particular component as being part of the system. 10.3.1.2 Result The equipment meets the requirements yes no n.a. Further test results are attached yes no 10.3.2 Manually operated transmitter deactivation 10.3.2.1 Regulation 15.231 (a1) A manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released 10.3.2.2 Result The equipment meets the requirements yes no n.a. Further test results are attached yes no Annex no: 10 10.3.3 Automatically operated transmitter deactivation 10.3.3.1 Regulation 15.231 (a2) A transmitter activated automatically shall cease transmission within 5 seconds after activation. 10.3.3.2 Result The equipment meets the requirements yes no n.a. Further test results are attached yes no page no: m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 19 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 10.3.4 Prohibition of periodic transmission 10.3.4.1 Regulation 15.231 (a3) Periodic transmissions at regular predetermined intervals are not permitted. However, polling or supervision transmissions to determine system integrity of transmitters used in security or safety applications are allowed if the periodic rate of transmission does not exceed one transmission of not more than one second duration per hour for each transmitter. 10.3.4.2 Result The equipment meets the requirements yes no n.a. Further test results are attached yes no page no: 10.3.5 Continuous transmission during an alarm condition 10.3.5.1 Regulation 15.231 (a4) Intentional radiators which are employed for radio control purposes during emergencies involving fire, security, and safety of life, when activated to signal an alarm, may operate during the pendency of the alarm condition. 10.3.5.2 Result The equipment meets the requirements yes no n.a. Further test results are attached yes no page no: m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 20 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 10.4 Bandwidth 10.4.1 Regulation 15.231 (c) The bandwidth of the emission shall be no wider than 0.25% of the centre frequency for devices operating above 70 MHz and below 900 MHz. For devices operating above 900 MHz, the emission shall be no wider than 0.5% of the centre frequency. Bandwidth is determined at the points 20 dB down from the modulated carrier. 10.4.2 Calculation of the 20 dB bandwidth limit The 20 dB bandwidth limit = 0.0025 * 315 MHz = 0.7875 MHz = 787.5 kHz 10.4.3 Test equipment Type Manufacturer/ Serial no. Last calibration Next calibration Model no. Receiver Hewlett Packard 3528U00990 05/2006 05/2008 (30MHz - 1GHz) Spectrum Analyzer (171) 8593 E Test fixture Dudde 10.4.4 Test procedure ANSI C63.4-1992 Section 13.1.7 Occupied bandwidth measurements. The bandwidth is measured at an amplitude level reduced from the reference level by a specified ratio. The reference level is the level of the highest amplitude signal observed from the transmitter at either the fundamental frequency or first-order modulation products in all typical modes of operation, including the unmodulated carrier, even if atypical. Once the reference level is established, the equipment is conditioned with typical modulating signals to produce worst-case (i.e., the widest) bandwidth. In order to measure the modulated signal properly, a resolution bandwidth that is small compared to the bandwidth required by the procuring or regulatory agency shall be used on the measuring instrument. However, the 6 dB resolution bandwidth of the measuring instrument shall be set to a value greater than 5% of the bandwidth requirements. m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 21 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 10.4.5 Test result The measured 20 dB bandwidth is: .................95.0 kHz The equipment meets the requirements yes no n.a. Further test results are attached yes no Annex no: 3 m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 22 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 10.5 Radiated emission (Measurement of the active transponder of the EUT) 10.5.1 Regulation Test Requirement: FCC CFR47, Part 15B Test Procedure: ANSI C63.4:1992 15.201(a) Intentional radiators operated as carrier current systems, devices operated under the provisions of §§ 15.211, 15.213 and 15.221, and devices operating below 490 kHz in which all emissions are at least 40 dB below the limits in Section 15.209 shall be verified pursuant to the procedures in Subpart J of Part 2 of this Chapter prior to marketing. Test Requirement: FCC CFR47, Part 15C Test Procedure: ANSI C63.4:1992 Section 15.209 (a) Except as provided elsewhere in this subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency Field strength Measurement distance (MHz) (microvolts/meter) (meters) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 30-88 100 3 88-216 150 3 216-960 200 3 Above 960 500 3 (b) In the emission table above, the tighter limit applies at the band edges. m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 23 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 (c) The level of any unwanted emissions from an intentional radiator operating under these general provisions shall not exceed the level of the fundamental emission. For intentional radiators which operate under the provisions of other sections within this part and which are required to reduce their unwanted emissions to the limits specified in this table, the limits in this table are based on the frequency of the unwanted emission and not the fundamental frequency. However, the level of any unwanted emissions shall not exceed the level of the fundamental frequency. (d) The emission limits shown in the above table are based on measurements employing a CISPR quasi peak detector except for the frequency bands 9-90 kHz, 110-490 kHz and above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector. (e) The provisions in §§ 15.31, 15.33, and 15.35 for measuring emissions at distances other than the distances specified in the above table, determining the frequency range over which radiated emissions are to be measured, and limiting peak emissions apply to all devices operated under this part. (f) In accordance with Section 15.33(a), in some cases the emissions from an intentional radiator must be measured to beyond the tenth harmonic of the highest fundamental frequency designed to be emitted by the intentional radiator because of the incorporation of a digital device. lf measurements above the tenth harmonic are so required, the radiated emissions above the tenth harmonic shall comply with the general radiated emission limits applicable to the incorporated digital device, as shown in Section 15.109 and as based on the frequency of the emission being measured, or, except for emissions contained in the restricted frequency bands shown in Section 15.205, the limit on spurious emissions specified for the intentional radiator, whichever is the higher limit. Emissions which must be measured above the tenth harmonic of the highest fundamental frequency designed to be emitted by the intentional radiator and which fall within the restricted bands shall comply with the general radiated emission limits in Section 15.109 that are applicable to the incorporated digital device. 10.5.2 Test equipment Type Manufacturer/ Serial no. Last calibration Next calibration Model no. Receiver Hewlett Packard 3528U00990 2006/03 2008/03 Spectrum Analyzer (9 kHz –26.5 GHz) 8593E (171) Pre-amplifier Hewlett Packard 1726A00705 2006/03 2008/03 (100kHz - 1.3GHz) 8447 E (166a) Magnetic antenna Schwarzbeck --- 2004/04 2008/04 (9.0-30 MHz) FMZB 1516 (23) Bilog antenna CHASE 1517 2004/04 2008/04 (30-1000 MHz) CBL611A (167) Horn antenna Schwarzbeck 236 1998/01 2008/01 (0.86-8.5 GHz) BBHA 9120 A (284) m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 24 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 10.5.3 Test procedures The EUT and this peripheral (when additional equipment exist) are placed on a turn table which is 0.8 m above the ground. The turn table would be allowed to rotate 360 degrees to determine the position of the maximum emission level. The test distance between the EUT and the receiving antenna are 3m. To find the maximum emission, the polarization of the receiving antenna is changed in horizontal and vertical polarization, the position of the EUT was changed in different orthogonal determinations. ANSI C63.4: 1992 Section 8 “Radiated Emissions Testing” Radiated emissions test characteristics Frequency range 30 MHz - 4,000 MHz Test distance 10m, 3 m* Test instrumentation resolution bandwidth 9 kHz (20 kHz – 30 MHz) 120 kHz (30 MHz - 1,000 MHz) 1 MHz (1000 MHz - 12,000 MHz) Receive antenna height 1 m (20 kHz – 30 MHz) Receive antenna polarization 0° - 90° (20 kHz – 30 MHz) Receive antenna scan height 1 m - 4 m (30 MHz - 12,000 MHz) Receive antenna polarization vertical/horizontal (30 MHz - 12,000 MHz) * According to Section 15.31 (f)(1): At frequencies at or above 30 MHz, measurements may be performed at a distance other than what is specified provided: measurements are not made in the near field except where it can be shown that near field measurements are appropriate due to the characteristics of the device; and it can be demonstrated that the signal levels needed to be measured at the distance employed can be detected by the measurement equipment. When performing measurements at a distance other than that specified, the results shall be extrapolated to the specified distance using an extrapolation factor of 20 dB/decade (inverse linear-distance for field strength measurements; inverse-linear-distance-squared for power density measurements). m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 25 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 10.5.4 Calculation of field strength Section 15.209 below 30 MHz The Receiver reading gives not directly the field strength result in (dBµV/m). The antenna factors of the loop antenna and cable losses must be added to find the correct result. For frequencies below 30 MHz and for an test distance other than what is specified, but fulfilling the requirements of Section 15.31 (f) (2) the field strength is calculated by adding additionally an extrapolation factor of 40 dB/decade (inverse linear distance for field strength measurements). The field strength is calculated by the following calculation: Corrected Level = Receiver Level + Correction Factor Corrected Level = Receiver Level + Correction Factor – Pre-amplifier (with the use of an Pre-amplifier) Receiver Level : Receiver reading without correction factors Correction Factor : Loop Antenna factor + cable loss FS = 40.7 - 40 = 0.7 [dBµV/m] Level in µV/m Common Antilogarithm (0.7/20) = 1.1 10.5.5 Calculation of field strength Section 15.209 above 30 MHz The field strength is calculated by the following calculation: Corrected Level = Receiver Level + Correction Factor (without the use of an Pre-amplifier) Corrected Level = Receiver Level + Correction Factor – Pre-amplifier (with the use of an Pre-amplifier) Receiver Level : Receiver reading without correction factors Correction Factor : Antenna factor + cable loss For test distance other than what is specified, but fulfilling the requirements of Section 15.31 (f)(1) the field strength is calculated by adding additionally an extrapolation factor of 20 dB/decade (inverse linear distance for field strength measurements). m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 26 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 10.5.6 Calculation of the field strength The field strength is calculated by the following calculation: Corrected Level = Receiver Level + Correction Factor (without the use of an Pre-amplifier) Corrected Level = Receiver Level + Correction Factor – Pre-amplifier (with the use of an Pre-amplifier) Receiver Level : Receiver reading without correction factors Correction Factor : Antenna factor + cable loss For example: The receiver reading is 32.7 dBµV. The antenna factor for the measured frequency is +2.5 dB(1/m) and the cable factor for the measured frequency is 0.71 dB, giving a field strength of 35.91dBµV/m. The 35.91dBµV/m value can be mathematically converted to its corresponding level in µV/m. Level in µV/m = Common Antilogarithm (35.91/20) = 39.8 For test distance other than what is specified, but fulfilling the requirements of Section 15.31 (f)(1) the field strength is calculated by adding additionally an extrapolation factor of 20 dB/decade (inverse linear distance for field strength measurements). 10.5.7 Calculation of Average Correction Factor The average correction factor is computed by analyzing the "worst case" on time in any 100msec time period and using the formula: Corrections Factor + 20*Iog (worst case on time/100msec) Analysis of the remote transmitter worst case on time in any 100msec time period is an on time of 50msec, there for the correction factor is 20*Iog(50/100) = - 6 dB. The maximum correction factor to be applied is 20 dB per section 15.35 of the FCC rules. m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 27 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 TRANSPONDER SPURIOUS RADIATION BELOW 30 MHz (Section 15.109) Polarisation f Bandwidth Noted Test Correction Distance Level Limit Margin EUT (MHz) (kHz), receiver distance factor extrapol. corrected / Type level factor antenna of detector m dB dB dBµV/m dBµV/m dBµV/m orientation dBµV 0.1200 QPK/0.2kHz < 4.0 10 20.2 -59.1 26.0 @ 300 V, H/0-360° -34.90 80.90 0.5000 QPK/0.2kHz < 4.0 3 20.2 -40.0 33.6 @ 30 V, H/0-360° -15.8 49.4 1.5000 QPK/9kHz < 4.0 3 20.2 -40.0 24.1 @ 30 V, H/0-360° -15.8 39.9 3.0000 QPK/9kHz < 4.0 3 20.2 -40.0 29.5 @ 30 V, H/0-360° -15.8 45.3 5.0000 QPK/9kHz < 4.0 3 20.2 -40.0 29.5 @ 30 V, H/0-360° -15.8 45.3 8.0000 QPK/9kHz < 4.0 3 20.2 -40.0 29.5 @ 30 V, H/0-360° -15.8 45.3 10.0000 QPK/9kHz < 4.0 3 20.2 -40.0 29.5 @ 30 -15.8 45.3 V, H/0-360° 20.0000 QPK/9kHz < 4.0 3 20.2 -40.0 29.5 @ 30 -15.8 45.3 V, H/0-360° 30.0000 QPK/9kHz < 4.0 3 20.2 -40.0 29.5 @ 30 -15.8 45.3 V, H/0-360° No emissions detected Measurement uncertainty 4 dB Remark: *1 Noise level of the measuring instrument ≤ 4.0dBµV @ 10m distance (0.009 MHz –30 MHz) Remark: * Peak Limit according to Section 15.35 (b). The equipment meets the requirements yes no n.a. Further test results are attached yes no page no: n.a x see page no. 29 m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 28 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 TRANSPONDER SPURIOUS RADIATION ABOVE 30 MHz (Section 15.209) AV Polaris. Antenna f Bandwidth Noted Test Correction Distance Level Limit Margin Correction EUT height (MHz) (kHz)/Type receiver distance factor extrapol. corrected factor / of detector level factor antenna dBµV m dB dB dBµV/m dBµV/m dBµV/m dB cm 30.0000 100, QPK ≤ 3.5 1 -2.6 9.5 0 -8.6 40.00 48.6 H,V/H,V 100-400 88.0000 100, QPK ≤ 3.5 1 -10.8 9.5 0 -16.8 40.00 56.8 H,V/H,V 100-400 216.0000 100, QPK ≤ 3.5 1 -10.3 9.5 0 -16.3 43.50 59.8 H,V/H,V 100-400 960.0000 100, QPK ≤ 3.5 1 8.5 9.5 0 2.5 43.50 41.0 H,V/H,V 100-400 Measurement uncertainty 4 dB * Bandwidth = the measuring receiver bandwidth Remark: *1 noise floor noise level of the measuring instrument ≤ 3.5dBµV @ 3m distance (30 – 1,000 MHz) Remark: *2 noise floor noise level of the measuring instrument ≤ 4.5 dBµV @ 3m distance (1,000 – 2,000 MHz) Remark: *3 noise floor noise level of the measuring instrument ≤ 10 dBµV @ 3m distance (2,000 – 5,500 MHz) Remark: *4 noise floor noise level of the measuring instrument ≤ 14 dBµV @ 3m distance (5,500 – 14,500 MHz) Remark: *5 for using a pre-amplifier in the range between 100 kHz and 1,000 MHz Remark: *6 for using a pre-amplifier in the range between 4.0 GHz and 18.0 GHz The equipment meets the requirements yes no n.a. Further test results are attached yes no page no: n.a x see page no. 29 m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 29 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 11 Additional information to this test report Remarks n.a.1 Not applicable, because the antenna is part of the PCB n.a.2 Not applicable, because the EUT is directly battery powered m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test report no. 07004143 Page 30 of 30 EUT: FBSB802 ID-Geber Basis FCC ID: IYZFBSB802 Date of issue: 2007-05-21 End of test report m. dudde hochfrequenz-technik Rottland 5a Vers. no. 1.06 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com


Document Created: 2007-10-24 11:42:31
Document Modified: 2007-10-24 11:42:31
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC