Test report Basis

FCC ID: IYZDC07

Test Report

Download: PDF
FCCID_974746

Test report no. 08004786 Page 1 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 DAT-P-225/96 Test Report acc. to the relevant standard 47 CFR Part 15 C – Intentional Radiators Measurement Procedure: ANSI C63.4-2003 relating to Marquardt GmbH BR212 Key Basis Methods of Measurement of Radio- Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range 9 kHz to 40 GHz DAT-P-225/96 State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 2 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 Manufacturer’s details Manufacturer Marquardt GmbH Manufacturer’s grantee code IYZ Manufacturer’s address Schloßstrasse 16 D-78604 Rietheim Weilheim Germany Phone : +49 7424 99 1960 Fax : +49 7424 99 2419 E- Mail: uwe.schwalm@marquardt.de Relevant standard used 47 CFR Part 15C - Intentional Radiators ANSI C63.4-2003 Test report prepared by Technical engineer Ralf Trepper m.dudde hochfrequenz-technik (laboratory) Rottland 5a 51429 Bergisch Gladbach Germany Phone: +49 (0) 2207 96 89-0 Fax: +49 (0) 2207 96 89-20 E-mail: m.duddelabor@dudde.com Equipment Under Test (EUT) Equipment category Transmitter Trade name Marquardt Type designation BR212 Key Basis Serial no. --- Variants BR212 Key Basis (1 channel) BR212 Key Basis (3 channel) State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 3 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 1. Test result summary Report Requirements CFR Section Test result Chapter Headline 15.203 11.1 Antenna requirement Pass Fail N.t. 15.205 11.2 Restricted bands of operation Pass Fail N.t. 15.209 11.3 Radiated emission limits, general requirements Pass Fail N.t. 15.231(a) 11.4 Periodic operation characteristics Pass Fail N.t. 15.231(b) 11.5 Fundamental frequencies / Field strength limits Pass Fail N.t. 15.231(c) 11.6 Bandwidth (20 dB) Pass Fail N.t. 15.201 (a) 11.7 Equipment authorization requirement Pass Fail N.t. 15.209 The equipment meets the requirements Yes No Signature Technician Ralf Trepper Signature Manager Manfried Dudde State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 4 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 Table of contents 1. Test result summary .......................................................................................................................................... 3 2. Test laboratory .................................................................................................................................................. 5 3. Introduction....................................................................................................................................................... 5 4. Product.............................................................................................................................................................. 6 5. Test schedule..................................................................................................................................................... 6 6. Product and measurement documentation .......................................................................................................... 7 7. Observations and comments .............................................................................................................................. 7 8. Summary........................................................................................................................................................... 7 9. Conclusions...................................................................................................................................................... 8 10. Operational description .................................................................................................................................. 9 11.1 Antenna requirement..................................................................................................................................... 10 11.1.1 Regulation........................................................................................................................................... 10 11.1.2 Result .................................................................................................................................................. 10 11.2 Restricted bands of operation....................................................................................................................... 11 11.2.1 Regulation........................................................................................................................................... 11 11.2.2 Result .................................................................................................................................................. 13 11.3 Radiated emission limits, general requirements........................................................................................... 14 11.3.1 Regulation........................................................................................................................................... 14 11.3.2 Test equipment.................................................................................................................................... 15 11.3.3 Test procedure..................................................................................................................................... 16 11.3.4 Calculation of the field strength.......................................................................................................... 17 11.3.5 Test result............................................................................................................................................ 18 11.4 Periodic operation characteristics ................................................................................................................ 20 11.4.1 Regulation........................................................................................................................................... 20 11.4.2 Test results .......................................................................................................................................... 20 11.5 Fundamental frequencies / Field strength limits .......................................................................................... 22 11.5.1 Regulation........................................................................................................................................... 22 11.5.2 Test equipment.................................................................................................................................... 23 11.5.3 Test procedure..................................................................................................................................... 24 11.5.4 Calculation of field strength limits ..................................................................................................... 25 11.5.5 Calculation of the average correction factor ....................................................................................... 25 11.5.6 Calculation of the field strengths ........................................................................................................ 26 11.5.7 Test result............................................................................................................................................ 27 11.6 Bandwidth (20 dB)....................................................................................................................................... 31 11.6.1 Regulation........................................................................................................................................... 31 11.6.2 Calculation of the 20 dB bandwidth limit........................................................................................... 31 11.6.3 Test equipment.................................................................................................................................... 31 11.6.4 Test procedure..................................................................................................................................... 31 11.6.5 Test result............................................................................................................................................ 32 12. Additional information to the test report........................................................................................................ 33 State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 5 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 2. Test laboratory Company name : m.dudde hochfrequenz-technik Street : Rottland 5a City : 51429 Bergisch Gladbach Country : Germany Laboratory : FCC Registration Number: 699717 This site has been fully described in a report submitted to the FCC, and renewed with letter dated July 12, 2005, Registration Number 699717. Phone : +49-2207-9689-0 Fax : +49-2207-9689-20 E-Mail : manfred.dudde@t-online.de Web : http://www.dudde.com 3. Introduction The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of m. dudde hochfrequenz - technik. This report contains the result of tests performed by m. dudde hochfrequenz - technik for the purpose of a type approval. The order for carrying out these tests has been placed by: Manufacturer Company name : Marquardt GmbH Address : Schloßstrasse 16 Postcode : D-78604 City/town : Rietheim-Weilheim Country : Germany Telephone : +49 7424 99 1960 Telefax : +49 7442 99 2419 E-Mail : uwe.schwalm@marquardt.de Date of order : 2008-03-17 References : Mr. Uwe Schwalm State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 6 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 4. Product Samples of the following apparatus were submitted for testing: Type of equipment : Transmitter Trademark : Marquardt Type designation : BR212 Key Basis Hardware version : BR212 Key Basis Serial number : --- Software release : --- Power used : 3.00 VDC Frequency used : 1 channel version 315.000 MHz 3 channel version 314.000 MHz / 314.450 MHz / 314.900 MHz Generated or used frequencies : 18 MHz / 314.000 MHz / 314.450 MHz / 314.900 MHz / 315.000 MHz ITU emission class : 109K F1D FCC ID : IYZDC07 5. Test schedule The tests were carried out in accordance with the specifications detailed in chapter 7 “Summary“ of this report at: - m. dudde hochfrequenz - technik, D-51429 Bergisch Gladbach The test sample was received on: - 2008-03-17 The tests were carried out in the following period of time: - 2008-05-22 - 2008-05-26 State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 7 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 6. Product and measurement documentation For issuing this report the following product documentation was used and the following annexes were created: Description Date Identifications External photographs of the Equipment Under Test 2008-05-30 Annex no. 1 Internal photographs of the Equipment Under Test 2008-05-30 Annex no. 2 Occupied bandwidth plot 2008-05-27 Annex no. 3 FCC ID label sample 2008-06-03 Annex no. 4 Functional description / User Manual 2008-05-30 Annex no. 5 Test setup photos 2008-05-23 Annex no. 6 Block diagram 2008-05-30 Annex no. 7 Schematics 2008-05-30 Annex no. 8a Parts list 2008-05-30 Annex no. 8b Operational description 2008-05-30 Annex no. 9 Periodic operation characteristic 2008-05-30 Annex No. 10 The above mentioned documentation will be filed at m. dudde hochfrequenz - technik for a period of 10 years following the issue of this test report. 7. Observations and comments 8. Summary The product is intended for the use in the following areas of application: Radio-Noise Emissions from Low- Voltage Electrical and Electronic Equipment in the frequency range of 9 kHz to 40 GHz The samples were tested according to the following specification: 47 CFR Part 15 – Intentional Radiators, ANSI C63.4-2003 State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 8 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 9. Conclusions Samples of the apparatus were found to CONFORM WITH the specifications stated in chapter 8 "Summary" of this report. In the opinion of m. dudde hochfrequenz - technik, the samples satisfied all applicable requirements relating to the network interface types specified in chapter 8. The results of the type tests as stated in this report are exclusively applicable to the product item as identified in this report. m. dudde hochfrequenz - technik does not accept any responsibility for the results stated in this report, with respect to the properties of product items not involved in these tests. This report consists of a main module, modules with test results and annexes listed in chapter 6. All pages have been numbered consecutively and bear the m. dudde hochfrequenz - technik logo, the report number and sub- numbers. The total number of pages in this report is 34. Technical inspector: Date : 2008-06-03 Name : Ralf Trepper Signature : Technical responsibility for area of testing: Date : 2008-06-03 Name : Manfried Dudde Signature : State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 9 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 10. Operational description 10.1 EUT details See Annex no. 5 (Technical description) 10.2 EUT configuration The Transceiver BR212 Key Basis operated in the continuous transmitting mode after pressing a bottom. described in Annex no. 5 (Technical description) 10.3 EUT measurement description The Transceiver BR212 Key Basis was tested in a typical fashion. During preliminary emission tests the Transceiver BR212 Key Basis was operated in the continuous transmitting mode for worst case emission mode investigation. Therefore, the final qualification testing was completed with Transceiver BR212 Key Basis operated in continuous modes. All tests were performed with the applicant’s declared maximal voltage: 3.0 V DC In order to establish the maximum radiation, firstly, there have been viewed all orthogonal adjustments of the test samples, secondly the test ample have been rotated at all adjustments around the own axis between 0° and 360°, and thirdly, the antenna polarization between horizontal and vertical had been varied. State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 10 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 11.1 Antenna requirement 11.1.1 Regulation An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this Section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier current devices or to devices operated under the provisions of Sections 15.211, 15.213, 15.217, 15.219, or 15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional radiators which, in accordance with Section 15.31(d), must be measured at the installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed so that the limits in this Part are not exceeded. 11.1.2 Result The equipment meets the requirements Yes No N.t. Further test results are attached Yes No n.a.* See page no. 38 State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 11 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 11.2 Restricted bands of operation 11.2.1 Regulation (a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz 0.090 - 0.110 16.42 - 16.423 399.9 - 410 4.5 - 5.15 1 0.495 - 0.505 16.69475 - 16.69525 608 - 614 5.35 - 5.46 2.1735 - 2.1905 16.80425 - 16.80475 960 - 1240 7.25 - 7.75 4.125 - 4.128 25.5 - 25.67 1300 - 1427 8.025 - 8.5 4.17725 - 4.17775 37.5 - 38.25 1435 - 1626.5 9.0 - 9.2 4.20725 - 4.20775 73 - 74.6 1645.5 - 1646.5 9.3 - 9.5 6.215 - 6.218 74.8 - 75.2 1660 - 1710 10.6 - 12.7 6.26775 - 6.26825 108 - 121.94 1718.8 - 1722.2 13.25 - 13.4 6.31175 - 6.31225 123 - 138 2200 - 2300 14.47 - 14.5 8.291 - 8.294 149.9 - 150.05 2310 - 2390 15.35 - 16.2 8.362 - 8.366 156.52475 - 156.52525 2483.5 - 2500 17.7 - 21.4 8.37625 - 8.38675 156.7 - 156.9 2690 - 2900 22.01 - 23.12 8.41425 - 8.41475 162.0125 - 167.17 3260 - 3267 23.6 - 24.0 12.29 - 12.293 167.72 - 173.2 3332 - 3339 31.2 - 31.8 12.51975 - 12.52025 240 - 285 3345.8 - 3358 36.43 - 36.5 12.57675 - 12.57725 322 - 335.4 3600 - 4400 (2 ) 13.36 - 13.41 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6 (b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. (c) Except as provided in paragraphs (d) and (e), regardless of the field strength limits specified elsewhere in this Subpart, the provisions of this Section apply to emissions from any intentional radiator. State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 12 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 (d) The following devices are exempt from the requirements of this Section: (1) Swept frequency field disturbance sensors operating between 1.705 and 37 MHz provided their emissions only sweep through the bands listed in paragraph (a), the sweep is never stopped with the fundamental emission within the bands listed in paragraph (a), and the fundamental emission is outside of the bands listed in paragraph (a) more than 99% of the time the device is actively transmitting, without compensation for duty cycle. (2) Transmitters used to detect buried electronic markers at 101.4 kHz which are employed by telephone companies. (3) Cable locating equipment operated pursuant to Section 15.213. (4) Any equipment operated under the provisions of § 15.253, § 15.255 or § 15.257 of this part. (5) Biomedical telemetry devices operating under the provisions of Section 15.242 of this part are not subject to the restricted band 608-614 MHz but are subject to compliance within the other restricted bands. (6) Transmitters operating under the provisions of Subpart D or F of this part. (7) Devices operated pursuant to § 15.225 are exempt from complying with this section for the 13.36-13.41 MHz band only. (8) Devices operated in the 24.075-24.175 GHz band under § 15.245 are exempt from complying with the requirements of this section for the 48.15-48.35 GHz and 72.225-72.525 GHz bands only, and shall not exceed the limits specified in § 15.245(b). (9) Devices operated in the 24.0-24.25 GHz band under § 15.249 are exempt from complying with the requirements of this section for the 48.0-48.5 GHz and 72.0-72.75 GHz bands only, and shall not exceed the limits specified in § 15.249(a). (e) Harmonic emissions appearing in the restricted bands above 17.7 GHz from field disturbance sensors operating under the provisions of Section 15.245 shall not exceed the limits specified in Section 15.245(b). (b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. (c) Except as provided in paragraphs (d) and (e), regardless of the field strength limits specified elsewhere in this Subpart, the provisions of this Section apply to emissions from any intentional radiator. (d) The following devices are exempt from the requirements of this Section: (1) Swept frequency field disturbance sensors operating between 1.705 and 37 MHz provided their emissions only sweep through the bands listed in paragraph (a), the sweep is never stopped with the fundamental emission within the bands listed in paragraph (a), and the fundamental emission is outside of the bands listed in paragraph (a) more than 99% of the time the device is actively transmitting, without compensation for duty cycle. State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 13 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 (2) Transmitters used to detect buried electronic markers at 101.4 kHz which are employed by telephone companies. (3) Cable locating equipment operated pursuant to Section 15.213. (4) Any equipment operated under the provisions of § 15.253, § 15.255 or § 15.257 of this part. (5) Biomedical telemetry devices operating under the provisions of Section 15.242 of this part are not subject to the restricted band 608-614 MHz but are subject to compliance within the other restricted bands. (6) Transmitters operating under the provisions of Subpart D or F of this part. (7) Devices operated pursuant to § 15.225 are exempt from complying with this section for the 13.36-13.41 MHz band only. (8) Devices operated in the 24.075-24.175 GHz band under § 15.245 are exempt from complying with the requirements of this section for the 48.15-48.35 GHz and 72.225-72.525 GHz bands only, and shall not exceed the limits specified in § 15.245(b). (9) Devices operated in the 24.0-24.25 GHz band under § 15.249 are exempt from 83 complying with the requirements of this section for the 48.0-48.5 GHz and 72.0-72.75 GHz bands only, and shall not exceed the limits specified in § 15.249(a). (e) Harmonic emissions appearing in the restricted bands above 17.7 GHz from field disturbance sensors operating under the provisions of Section 15.245 shall not exceed the limits specified in Section 15.245(b). 11.2.2 Result The equipment meets the requirements Yes No N.t. Further test results are attached Yes No State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 14 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 11.3 Radiated emission limits, general requirements 11.3.1 Regulation (a) Except as provided elsewhere in this subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency Field Strength Measurement distance (MHz) (microvolts/meter) (meters) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 30-88 100 3 88-216 150 3 216-960 200 3 Above 960 500 3 (b) In the emission table above, the tighter limit applies at the band edges. (c) The level of any unwanted emissions from an intentional radiator operating under these general provisions shall not exceed the level of the fundamental emission. For intentional radiators which operate under the provisions of other sections within this part and which are required to reduce their unwanted emissions to the limits specified in this table, the limits in this table are based on the frequency of the unwanted emission and not the fundamental frequency. However, the level of any unwanted emissions shall not exceed the level of the fundamental frequency. (d) The emission limits shown in the above table are based on measurements employing a CISPR quasi peak detector except for the frequency bands 9-90 kHz, 110-490 kHz and above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector. (e) The provisions in §§ 15.31, 15.33, and 15.35 for measuring emissions at distances other than the distances specified in the above table, determining the frequency range over which radiated emissions are to be measured, and limiting peak emissions apply to all devices operated under this part. (f) In accordance with Section 15.33(a), in some cases the emissions from an intentional radiator must be measured to beyond the tenth harmonic of the highest fundamental frequency designed to be emitted by the intentional radiator because of the incorporation of a digital device. lf measurements above the tenth harmonic are so required, the radiated emissions above the tenth harmonic shall comply with the general radiated emission limits applicable to the incorporated digital device, as shown in Section 15.109 and as based on the frequency of the emission being measured, or, except for emissions contained in the restricted frequency bands shown in Section 15.205, the limit on spurious emissions specified for the intentional radiator, whichever is the higher limit. Emissions which must be measured above the tenth harmonic of the highest fundamental frequency designed to be emitted by the intentional radiator and which fall within the restricted bands shall comply with the general radiated emission limits in Section 15.109 that are applicable to the incorporated digital device. State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 15 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 11.3.2 Test equipment Type Manufacturer/ Serial no. Last calibration Next calibration Model no. Receiver Hewlett Packard 3528U00990 2007/08 2009/08 Spectrum Analyzer (9 kHz –26.5 GHz) 8593E (171) Pre-amplifier Hewlett Packard 1726A00705 2008/02 2010/02 (100kHz - 1.3GHz) 8447 E (166a) Pre-amplifier Narda --- 2008/02 2010/02 (1GHz - 18GHz) --- (345) Bilog antenna Schwarzbeck 2007/02 2013/02 (30- 1000 MHz) VULP 9168 (406) Horn antenna Schwarzbeck 236 2008/01 2013/01 (0.86-8.5 GHz) BBHA 9120 A (284) Horn antenna Schwarzbeck 305 2008/01 2013/01 (2.0-14.0 GHz) BBHA 9120 C (169) RF- cable Kabelmetal 18m [N] K1 2008/01 2009/01 RF- cable Aircell 0.5m [BNC] K40 2008/01 2009/01 RF- cable Aircell 1m [BNC/N] K56 2008/01 2009/01 RF- cable Sucoflex 106 Suhner K74 2008/01 2009/01 6,4m [N] RF- cable Sucoflex 106 Suhner K75 2008/01 2009/01 6,4m [N] State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 16 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 11.3.3 Test procedure The EUT and this peripheral (when additional equipment exists) are placed on a turn table which is 0.8 m above the ground. The turn table would be allowed to rotate 360 degrees to determine the position of the maximum emission level. The test distance between the EUT and the receiving antenna are 3m. To find the maximum emission, the polarization of the receiving antenna is changed in horizontal and vertical polarization; the position of the EUT was changed in different orthogonal determinations. ANSI C63.4: 2003 Section 8 “Radiated Emissions Testing” Measurement procedures for electric field radiated emissions above 1 GHz are covered in Clause 8 of ANSI C63.4- 2003. The C63.4-2003 measurement procedure consists of both an exploratory test and a final measurement. The exploratory test is critical to determine the frequency of all significant emissions. For each mode of operation required to be tested, the frequency spectrum is monitored. Variations in antenna height, antenna orientation, antenna polarization, EUT azimuth, and cable or wire placement is explored to produce the emission that has the highest amplitude relative to the limit. The final measurements are made based on the findings in the exploratory testing. When making exploratory and final measurements it is necessary to maximize the measured radiated emission. Subclause 8.3.1.2 of C63.4-2003 states that the measurement is to be made “while keeping the antenna in the ‘cone of radiation’ from that area and pointed at the area both in azimuth and elevation, with polarization oriented for maximum response.” We consider the “cone of radiation” to be the 3 dB beamwidth of the measurement antenna. While the “bore-sighting” technique is not explicitly mentioned in C63.4-2003, it is a useful technique for measurements using a directional antenna, such as a double-ridged waveguide antenna. Several precautions must be observed, including: knowledge of the beamwidth of the antenna and the resulting illumination area relative to the size of the EUT, estimation for source of the emission and general location within larger EUTS, measuring system sensitivity, etc. C63.4-2003 requires that the measurement antenna is kept pointed at the source of the emission both in azimuth and elevation, with the polarization of the antenna oriented for maximum response. That means that if the directional radiation pattern of the EUT results in a maximum emission at an upwards angle from the EUT, when a directional antenna is used to make the measurement it will be necessary for it to be pointed towards the source of the emission within the EUT. This can be done by either pointing the antenna at an angle towards the source of the emission, or by rotating the EUT, in both height and polarization, to maximize the measured emission. The emission must be kept within the illumination area of the 3 dB beamwidth of the antenna so that the maximum emission from the EUT is measured. State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 17 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 Radiated emissions test characteristics Frequency range 30 MHz - 4,000 MHz Test distance 3 m* Test instrumentation resolution bandwidth 120 kHz (30 MHz - 1,000 MHz) 1 MHz (1000 MHz - 4,000 MHz) Receive antenna scan height 1m-4m Receive antenna polarization Vertical/horizontal * According to Section 15.31 (f) (1): At frequencies at or above 30 MHz, measurements may be performed at a distance other than what is specified provided: measurements are not made in the near field except where it can be shown that near field measurements are appropriate due to the characteristics of the device; and it can be demonstrated that the signal levels needed to be measured at the distance employed can be detected by the measurement equipment. When performing measurements at a distance other than that specified, the results shall be extrapolated to the specified distance using an extrapolation factor of 20dB/decade (inverse linear-distance for field strength measurements; inverse-linear-distance-squared for power density measurements). 11.3.4 Calculation of the field strength The field strength is calculated by the following calculation: Corrected Level = Receiver Level + Correction Factor (without the use of a pre-amplifier) Corrected Level = Receiver Level + Correction Factor – Pre-amplifier (with the use of a pre-amplifier) Receiver Level : Receiver reading without correction factors Correction Factor : Antenna factor + cable loss For example: The receiver reading is 32.7 dBµV. The antenna factor for the measured frequency is +2.5 dB (1/m) and the cable factor for the measured frequency is 0.71 dB, giving a field strength of 35.91dBµV/m. The 35.91dBµV/m value can be mathematically converted to its corresponding level in µV/m. Level in µV/m = Common Antilogarithm (35.91/20) = 39.8 For test distance other than what is specified, but fulfilling the requirements of Section 15.31 (f) (1) the field strength is calculated by adding additionally an extrapolation factor of 20 dB/decade (inverse linear distance for field strength measurements). State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 18 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 11.3.5 Test result TRANSMITTER SPURIOUS RADIATION BELOW 30 MHz (Section 15.205, 15.209) Polarisation f Bandwidth Noted Test Correction Distance Level Limit Margin EUT (MHz) (kHz) receiver level distance factor extrapol. corrected / Type factor antenna of detector dBµV m dB dB dBµV/m dBµV/m dBµV/m orientation 0.1200 PK/0.2kHz < 4.0 10 -59.1 Pk46.0- @ 300 V, H/0-360° 20.2 -34.90 80.90 AV/0.2kHz < 4.0 10 20.2 -59.1 AV26.0 @ 300 V, H/0-360° -34.90 80.90 0.5000 AV/0.2kHz < 4.0 10 20.2 -19.1 AV33.6 @ 30 V, H/0-360° 5.10 28.5 1.5000 AV/0.2kHz < 4.0 10 20.2 -19.1 AV24.1 @ 30 V, H/0-360° 5.10 19.00 3.0000 AV/9.0kHz < 4.0 10 20.2 -19.1 AV29.5 @ 30 V, H/0-360° 5.10 24.4 5.0000 AV/9.0kHz < 4.0 10 20.2 -19.1 AV29.5 @ 30 V, H/0-360° 5.10 24.4 8.0000 AV/9.0kHz < 4.0 10 20.2 -19.1 AV29.5 @ 30 V, H/0-360° 5.10 24.4 10.0000 AV/9.0kHz < 4.0 10 20.2 -19.1 AV29.5 @ 30 5.10 24.4 V, H/0-360° 20.0000 AV/9.0kHz < 4.0 10 20.2 -19.1 AV29.5 @ 30 5.10 24.4 V, H/0-360° 30.0000 AV/9.0kHz < 4.0 10 20.2 -19.1 AV29.5 @ 30 5.10 24.4 V, H/0-360° No emissions detected Measurement uncertainty 4 dB Remark: *1 Noise level of the measuring instrument ≤ 4.0dBµV @ 10m distance (0.009 MHz –30 MHz) Remark: * Peak Limit according to Section 15.35 (b). The equipment meets the requirements Yes No N.t. Further test results are attached Yes No State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 19 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 TRANSMITTER SPURIOUS RADIATION ABOVE 30 MHz (Section 15.205, 15.209) AV Polaris. Antenna f Bandwidth Noted Test Correction Distance Level Limit Margin Correction EUT height (MHz) (kHz) receiver distance factor extrapol. corrected factor / Type level factor antenna of detector dBµV m dB dB dBµV/m dBµV/m dBµV/m dB cm 30.0000 100, AV ≤ 3.5 3 -2.60 0 0 0.90 40.00 39.10 H,V/H,V 100-400 88.0000 100, AV ≤ 3.5 3 -10.80 0 0 -7.30 40.00 47.30 H,V/H,V 100-400 216.0000 100, AV ≤ 3.5 3 -10.30 0 0 -6.80 43.50 50.30 H,V/H,V 100-400 960.0000 100, AV ≤ 3.5 3 8.50 0 0 12.00 43.50 31.50 H,V/H,V 100-400 1700.0000 1000, AV ≤ 4.5 3 3.80 0 0 8.30 54.00 45.70 H,V/H,V 100-400 2250.0000 1000, AV ≤ 10 3 8.00 0 0 18.00 54.00 36.00 H,V/H,V 100-400 4000.0000 1000, AV ≤ 10 3 6 0 0 18.40 54.00 35.60 H,V/H,V 100-400 8.40* 5000.0000 1000, AV ≤ 10 3 6 0 0 19.40 54.00 34.60 H,V/H,V 100-400 9.10* 7500.0000 1000, AV ≤ 14 3 6 0 0 26.90 54.00 27.10 H,V/H,V 100-400 12.9* 0 8300.0000 1000, AV ≤ 14 3 6 0 0 28.80 54.00 25.20 H,V/H,V 100-400 14.80* 9400.0000 1000, AV ≤ 14 3 6 0 0 30.00 54.00 24.00 H,V/H,V 100-400 16.00* 11000.0000 1000, AV ≤ 14 3 6 0 0 32.25 54.00 21.75 H,V/H,V 100-400 18.25* Measurement uncertainty 4 dB Bandwidth = the measuring receiver bandwidth Remark: *1 noise floor noise level of the measuring instrument ≤ 3.5dBµV @ 3m distance (30 – 1,000 MHz) Remark: *2 noise floor noise level of the measuring instrument ≤ 4.5dBµV @ 3m distance (1,000 – 2,000 MHz) Remark: *3 noise floor noise level of the measuring instrument ≤ 10dBµV @ 3m distance (2,000 – 5,500 MHz) Remark: *4 noise floor noise level of the measuring instrument ≤ 14dBµV @ 3m distance (5,500 – 14,500 MHz) Remark: *5 for using a pre-amplifier in the range between 100 kHz and 1,000 MHz Remark: *6 for using a pre-amplifier in the range between 1.0 GHz and 18.0 GHz The equipment meets the requirements Yes No N.t. Further test results are attached Yes No State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 20 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 11.4 Periodic operation characteristics 11.4.1 Regulation (a) The provisions of this Section are restricted to periodic operation within the band 40.66 - 40.70 MHz and above 70 MHz. Except as shown in paragraph (e) of this Section, the intentional radiator is restricted to the transmission of a control signal such as those used with alarm systems, door openers, remote switches, etc. Continuous transmissions, voice, video and the radio control of toys are not permitted. Data is permitted to be sent with a control signal. The following conditions shall be met to comply with the provisions for this periodic operation: 11.4.2 Test results The equipment meets the requirements Yes No N.t. Further test results are attached Yes No (1) A manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released. The equipment meets the requirements Yes No N.t. Further test results are attached Yes No Annex no: 11 (2) A transmitter activated automatically shall cease transmission within 5 seconds after activation. The equipment meets the requirements Yes No N.t. Further test results are attached Yes No Annex no: 11 (3) Periodic transmissions at regular predetermined intervals are not permitted. However, polling or supervision transmissions, including data, to determine system integrity of transmitters used in security or safety applications are allowed if the total duration of transmissions does not exceed more than two seconds per hour for each transmitter. There is no limit on the number of individual transmissions, provided the total transmission time does not exceed two seconds per hour. The equipment meets the requirements Yes No N.t. Further test results are attached Yes No State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 21 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 (4) Intentional radiators which are employed for radio control purposes during emergencies involving fire, security, and safety of life, when activated to signal an alarm, may operate during the pendency of the alarm condition. The equipment meets the requirements Yes No N.t. Further test results are attached Yes No (5) Transmission of set-up information for security systems may exceed the transmission duration limits in paragraphs (a)(1) and (a)(2) of this section, provided such transmission are under the control of a professional installer and do not exceed ten seconds after a manually operated switch is released or a transmitter is activated automatically. Such set-up information may include data. The equipment meets the requirements Yes No N.t. Further test results are attached Yes No State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 22 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 11.5 Fundamental frequencies / Field strength limits 11.5.1 Regulation (b) In addition to the provisions of Section 15.205, the field strength of emissions from intentional radiators operated under this Section shall not exceed the following: Fundamental Field Strength of Field Strength of Frequency Fundamental Spurious Emissions (MHz) (microvolts/meter) (microvolts/meter) 40.66 - 40.70 2,250 225 70 - 130 1,250 125 130 - 174 1,250 to 3,750 ** 125 to 375 ** 174 - 260 3,750 375 260 - 470 3,750 to 12,500 ** 375 to 1,250 ** Above 470 12,500 1,250 ** linear interpolations [Where F is the frequency in MHz, the formulas for calculating the maximum permitted fundamental field strengths are as follows: for the band 130-174 MHz, uV/m at 3 meters = 56.81818(F) - 6136.3636; for the band 260-470 MHz, uV/m at 3 meters = 41.6667(F) - 7083.3333. The maximum permitted unwanted emission level is 20 dB below the maximum permitted fundamental level.] (1) The above field strength limits are specified at a distance of 3 meters. The tighter limits apply at the band edges. (2) Intentional radiators operating under the provisions of this Section shall demonstrate compliance with the limits on the field strength of emissions, as shown in the above table, based on the average value of the measured emissions. As an alternative, compliance with the limits in the above table may be based on the use of measurement instrumentation with a CISPR quasi-peak detector. The specific method of measurement employed shall be specified in the application for equipment authorization. If average emission measurements are employed, the provisions in Section 15.35 for averaging pulsed emissions and for limiting peak emissions apply. Further, compliance with the provisions of Section 15.205 shall be demonstrated using the measurement instrumentation specified in that section. (3) The limits on the field strength of the spurious emissions in the above table are based on the fundamental frequency of the intentional radiator. Spurious emissions shall be attenuated to the average (or, alternatively, CISPR quasi-peak) limits shown in this table or to the general limits shown in Section 15.209, whichever limit permits a higher field strength. State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 23 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 11.5.2 Test equipment Type Manufacturer/ Serial no. Last calibration Next calibration Model no. Receiver Hewlett Packard 3528U00990 2007/08 2009/08 Spectrum Analyzer (9 kHz –26.5 GHz) 8593E (171) Pre-amplifier Hewlett Packard 1726A00705 2008/02 2010/02 (100kHz - 1.3GHz) 8447 E (166a) Pre-amplifier Narda --- 2008/02 2010/02 (1GHz - 18GHz) --- (345) Bilog antenna Schwarzbeck 2007/02 2013/02 (30- 1000 MHz) VULP 9168 (406) Horn antenna Schwarzbeck 236 2008/01 2013/01 (0.86-8.5 GHz) BBHA 9120 A (284) Horn antenna Schwarzbeck 305 2008/01 2013/01 (2.0-14.0 GHz) BBHA 9120 C (169) RF- cable Kabelmetal 18m [N] K1 2008/01 2009/01 RF- cable Aircell 0.5m [BNC] K40 2008/01 2009/01 RF- cable Aircell 1m [BNC/N] K56 2008/01 2009/01 RF- cable Sucoflex 106 Suhner K74 2008/01 2009/01 6,4m [N] RF- cable Sucoflex 106 Suhner K75 2008/01 2009/01 6,4m [N] State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 24 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 11.5.3 Test procedure The EUT and this peripheral (when additional equipment exists) are placed on a turn table which is 0.8m above the ground. The turn table would be allowed to rotate 360 degrees to determine the position of the maximum emission level. The test distance between the EUT and the receiving antenna are 3m. To find the maximum emission, the polarization of the receiving antenna are changed in horizontal and vertical polarization, the position of the EUT was changed in different orthogonal determinations. ANSI C63.4: 2003 Section 8 “Radiated emission measurements” Measurement procedures for electric field radiated emissions above 1 GHz are covered in Clause 8 of ANSI C63.4- 2003. The C63.4-2003 measurement procedure consists of both an exploratory test and a final measurement. The exploratory test is critical to determine the frequency of all significant emissions. For each mode of operation required to be tested, the frequency spectrum is monitored. Variations in antenna height, antenna orientation, antenna polarization, EUT azimuth, and cable or wire placement is explored to produce the emission that has the highest amplitude relative to the limit. The final measurements are made based on the findings in the exploratory testing. When making exploratory and final measurements it is necessary to maximize the measured radiated emission. Subclause 8.3.1.2 of C63.4-2003 states that the measurement is to be made “while keeping the antenna in the ‘cone of radiation’ from that area and pointed at the area both in azimuth and elevation, with polarization oriented for maximum response.” We consider the “cone of radiation” to be the 3 dB beamwidth of the measurement antenna. While the “bore-sighting” technique is not explicitly mentioned in C63.4-2003, it is a useful technique for measurements using a directional antenna, such as a double-ridged waveguide antenna. Several precautions must be observed, including: knowledge of the beamwidth of the antenna and the resulting illumination area relative to the size of the EUT, estimation for source of the emission and general location within larger EUTS, measuring system sensitivity, etc. C63.4-2003 requires that the measurement antenna is kept pointed at the source of the emission both in azimuth and elevation, with the polarization of the antenna oriented for maximum response. That means that if the directional radiation pattern of the EUT results in a maximum emission at an upwards angle from the EUT, when a directional antenna is used to make the measurement it will be necessary for it to be pointed towards the source of the emission within the EUT. This can be done by either pointing the antenna at an angle towards the source of the emission, or by rotating the EUT, in both height and polarization, to maximize the measured emission. The emission must be kept within the illumination area of the 3 dB beamwidth of the antenna so that the maximum emission from the EUT is measured. State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 25 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 Radiated emissions test characteristics Frequency range 30 MHz - 4,000 MHz Test distance 3 m* Test instrumentation resolution bandwidth 120 kHz (30 MHz - 1,000 MHz) 1 MHz (1000 MHz - 4,000 MHz) Receive antenna scan height 1m-4m Receive antenna polarization Vertical/horizontal *According to Section 15.31 (f) (1): At frequencies at or above 30 MHz, measurements may be performed at a distance other than what is specified provided: measurements are not made in the near field except where it can be shown that near field measurements are appropriate due to the characteristics of the device; and it can be demonstrated that the signal levels needed to be measured at the distance employed can be detected by the measurement equipment. When performing measurements at a distance other than that specified, the results shall be extrapolated to the specified distance using an extrapolation factor of 20dB/decade (inverse linear-distance for field strength measurements; inverse-linear-distance-squared for power density measurements). 11.5.4 Calculation of field strength limits For example: Transmitter working on 315 MHz Limit for average measurements → 41.6667*(315 MHz) – 7083.3333 = 6041.677µV/m = 75.6dBµV/m @3m Limit for peak measurements → Limit for average measurements + 20dB = 95.6dBµV/m @3m 11.5.5 Calculation of the average correction factor The average correction factor is computed by analyzing the "worst case" on time in any 100msec time period and using the formula: Corrections Factor + 20*log (worst case on time/100msec). Analysis of the remote transmitter worst case on time in any 100msec time period is an on time of 50msec, therefore the correction factor is 20*log (50/100) = - 6 dB. The maximum correction factor to be applied is 20 dB per section 15.35 of the FCC rules. State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 26 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 11.5.6 Calculation of the field strengths The field strength is calculated by the following calculation: Corrected Level = Receiver Level + Correction Factor (without the use of a pre-amplifier) Corrected Level = Receiver Level + Correction Factor – Pre-Amplifier (with the use of a pre-amplifier) Receiver Level : Receiver reading without correction factors Correction Factor : Antenna factor + cable loss For example: The receiver reading is 32.7 dBµV. The antenna factor for the measured frequency is +2.5 dB (1/m) and the cable factor for the measured frequency is 0.71 dB, giving a field strength of 35.91dBµV/m. The 35.91dBµV/m value can be mathematically converted to its corresponding level in µV/m. Level in µV/m = Common Antilogarithm (35.91/20) = 39.8 For test distance other than what is specified, but fulfilling the requirements of Section 15.31 (f) (1) the field strength is calculated by adding additionally an extrapolation factor of 20 dB/decade (inverse linear distance for field strength measurements). State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 27 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 11.5.7 Test result One channel version (fnom = 315.000 MHz) TRANSMITTER SPURIOUS RADIATION (Section 15.231(b)) Polarisation Antenna f Bandwidth Noted Test Correction Distance Level Limit Margin EUT height (MHz) (kHz) / receiver level distance factor extrapol. corrected / Type factor antenna of detector dBµV m dB dB dBµV/m dBµV/m dBµV/m cm 5 314.9995 120, QPK 80.1 3 -7.5* 0 72.6 75.6 3.0 H 0° / H 100 5 629.9990 120, QPK 27.5 3 -1.9* 0 26.2 55.6 29.4 H 270° / H 117 5 944.9985 120, QPK 23.7 3 +1.2* 0 24.9 55.6 30.7 H 270° / H 130 6 1259.9980 1000, AV 50.0 3 +1.3* 0 51.3 55.6 4.3 H 90°/H 112 1574.9975 1000, AV 46.3 3 +2.8*6 0 49.1 54.0 4.9 H 90°/H 125 6 1889.9970 1000, AV 43.8 3 +3.8* 0 47.6 55.6 8.0 H 45°/H 106 6 2204.9965 1000, AV 30.2 3 +7.8* 0 38.1 54.0 15.9 H 290°/H 118 2519.9960 1000, AV 32.9 3 +7.9*6 0 40.8 55.6 14.8 H 0°/H 100 6 2834.9955 1000, AV 21.4 3 +9.6* 0 31.0 54.0 23.0 H 270°/H 107 6 3149.9950 1000, AV 15.6 3 +11.3* 0 26.9 55.6 28.7 H 210°/H 105 6 3464.9945 1000, AV ≤ 10 3 +13.7* 0 23.7 55.6 31.9 H,V/H,V 100-400 Measurement uncertainty 4 dB Bandwidth = the measuring receiver bandwidth Remark: *1 noise floor noise level of the measuring instrument ≤ 3.5dBµV @ 3m distance (30 – 1,000 MHz) Remark: *2 noise floor noise level of the measuring instrument ≤ 4.5dBµV @ 3m distance (1,000 – 2,000 MHz) Remark: *3 noise floor noise level of the measuring instrument ≤ 10dBµV @ 3m distance (2,000 – 5,500 MHz) Remark: *4 noise floor noise level of the measuring instrument ≤ 14dBµV @ 3m distance (5,500 – 14,500 MHz) Remark: *5 for using a pre-amplifier in the range between 100 kHz and 1,000 MHz Remark: *6 for using a pre-amplifier in the range between 4.0 GHz and 18.0 GHz The equipment meets the requirements Yes No N.t. Further test results are attached Yes No State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 28 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 Three channel version, channel 1 (fnom = 314.000 MHz) TRANSMITTER SPURIOUS RADIATION (Section 15.231(b)) Polarisation Antenna f Bandwidth Noted Test Correction Distance Level Limit Margin EUT height (MHz) (kHz) / receiver level distance factor extrapol. corrected / Type factor antenna of detector dBµV m dB dB dBµV/m dBµV/m dBµV/m cm 5 314.0014 120, QPK 80.9 3 -7.5* 0 73.4 75.6 2.2 H 0° / H 100 628.0028 120, QPK 44.5 3 -1.9*5 0 42.6 55.6 13.0 H 270° / H 119 5 942.0042 120, QPK 34.9 3 +1.2* 0 36.1 55.6 19.5 H 90° / H 130 6 1256.0056 1000, AV 50.0 3 +1.3* 0 51.3 55.6 4.3 H 270°/H 115 1570.0070 1000, AV 45.6 3 +2.8*6 0 48.4 54.0 5.6 H 90°/H 130 6 1884.0084 1000, AV 48.1 3 +3.8* 0 51.9 55.6 3.7 H 270°/H 106 6 2198.0098 1000, AV 24.7 3 +7.8* 0 32.5 55.6 23.1 H 340°/H 139 2512.0112 1000, AV 30.0 3 +7.9*6 0 37.9 55.6 17.7 H 350°/H 122 6 2826.0126 1000, AV 17.1 3 +9.6* 0 26.7 54.0 27.3 H 90°/H 110 6 3140.0140 1000, AV 12.5 3 +11.3* 0 23.8 55.6 31.8 H 210°/H 105 6 3454.0154 1000, AV ≤ 10 3 +13.7* 0 23.7 55.6 31.9 H,V/H,V 100-400 Measurement uncertainty 4 dB Bandwidth = the measuring receiver bandwidth Remark: *1 noise floor noise level of the measuring instrument ≤ 3.5dBµV @ 3m distance (30 – 1,000 MHz) Remark: *2 noise floor noise level of the measuring instrument ≤ 4.5dBµV @ 3m distance (1,000 – 2,000 MHz) Remark: *3 noise floor noise level of the measuring instrument ≤ 10dBµV @ 3m distance (2,000 – 5,500 MHz) Remark: *4 noise floor noise level of the measuring instrument ≤ 14dBµV @ 3m distance (5,500 – 14,500 MHz) Remark: *5 for using a pre-amplifier in the range between 100 kHz and 1,000 MHz Remark: *6 for using a pre-amplifier in the range between 4.0 GHz and 18.0 GHz The equipment meets the requirements Yes No N.t. Further test results are attached Yes No State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 29 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 Three channel version, channel 2 (fnom = 314.450 MHz) TRANSMITTER SPURIOUS RADIATION (Section 15.231(b)) Polarisation Antenna f Bandwidth Noted Test Correction Distance Level Limit Margin EUT height (MHz) (kHz) / receiver level distance factor extrapol. corrected / Type factor antenna of detector dBµV m dB dB dBµV/m dBµV/m dBµV/m cm 5 314.4514 120, QPK 80.6 3 -7.5* 0 73.1 75.6 2.5 H 0° / H 100 628.9028 120, QPK 44.0 3 -1.9*5 0 42.1 55.6 13.5 H 270° / H 119 5 943.3542 120, QPK 34.9 3 +1.2* 0 36.1 55.6 19.5 H 90° / H 130 6 1257.8056 1000, AV 48.2 3 +1.3* 0 49.5 55.6 6.1 H 270°/H 115 1572.2570 1000, AV 45.1 3 +2.8*6 0 47.9 54.0 6.1 H 90°/H 130 6 1886.7084 1000, AV 45.9 3 +3.8* 0 49.7 55.6 5.9 H 270°/H 106 6 2201.1598 1000, AV 24.8 3 +7.8* 0 32.6 54.0 21.4 H 340°/H 139 2515.6112 1000, AV 32.3 3 +7.9*6 0 40.2 55.6 15.4 H 350°/H 122 6 2830.0626 1000, AV 17.1 3 +9.6* 0 26.7 54.0 27.3 H 90°/H 110 6 3144.5140 1000, AV 14.8 3 +11.3* 0 26.1 55.6 29.5 H 210°/H 105 6 3458.9654 1000, AV ≤ 10 3 +13.7* 0 23.7 55.6 31.9 H,V/H,V 100-400 Measurement uncertainty 4 dB Bandwidth = the measuring receiver bandwidth Remark: *1 noise floor noise level of the measuring instrument ≤ 3.5dBµV @ 3m distance (30 – 1,000 MHz) Remark: *2 noise floor noise level of the measuring instrument ≤ 4.5dBµV @ 3m distance (1,000 – 2,000 MHz) Remark: *3 noise floor noise level of the measuring instrument ≤ 10dBµV @ 3m distance (2,000 – 5,500 MHz) Remark: *4 noise floor noise level of the measuring instrument ≤ 14dBµV @ 3m distance (5,500 – 14,500 MHz) Remark: *5 for using a pre-amplifier in the range between 100 kHz and 1,000 MHz Remark: *6 for using a pre-amplifier in the range between 4.0 GHz and 18.0 GHz The equipment meets the requirements Yes No N.t. Further test results are attached Yes No State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 30 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 Three channel version, channel 3 (fnom = 314.900 MHz) TRANSMITTER SPURIOUS RADIATION (Section 15.231(b)) Polarisation Antenna f Bandwidth Noted Test Correction Distance Level Limit Margin EUT height (MHz) (kHz) / receiver level distance factor extrapol. corrected / Type factor antenna of detector dBµV m dB dB dBµV/m dBµV/m dBµV/m cm 5 314.4514 120, QPK 80.9 3 -7.5* 0 73.4 75.6 2.2 H 0° / H 100 629.8028 120, QPK 44.5 3 -1.9*5 0 42.6 55.6 13.0 H 270° / H 119 5 944.7042 120, QPK 34.7 3 +1.2* 0 35.9 55.6 19.7 H 90° / H 130 6 1259.6056 1000, AV 49.9 3 +1.3* 0 51.2 55.6 4.4 H 270°/H 115 1574.5070 1000, AV 45.8 3 +2.8*6 0 48.6 54.0 5.4 H 90°/H 130 6 1889.4084 1000, AV 48.8 3 +3.8* 0 52.6 55.6 3.0 H 270°/H 106 6 2204.3098 1000, AV 24.7 3 +7.8* 0 32.5 54.0 21.5 H 340°/H 139 2519.2112 1000, AV 30.0 3 +7.9*6 0 37.9 55.6 17.7 H 350°/H 122 6 2834.1126 1000, AV 17.1 3 +9.6* 0 26.7 54.0 27.3 H 90°/H 110 6 3149.0140 1000, AV 12.3 3 +11.3* 0 23.6 55.6 32.0 H 210°/H 105 6 3463.9154 1000, AV ≤ 10 3 +13.7* 0 23.7 55.6 31.9 H,V/H,V 100-400 Measurement uncertainty 4 dB Bandwidth = the measuring receiver bandwidth Remark: *1 noise floor noise level of the measuring instrument ≤ 3.5dBµV @ 3m distance (30 – 1,000 MHz) Remark: *2 noise floor noise level of the measuring instrument ≤ 4.5dBµV @ 3m distance (1,000 – 2,000 MHz) Remark: *3 noise floor noise level of the measuring instrument ≤ 10dBµV @ 3m distance (2,000 – 5,500 MHz) Remark: *4 noise floor noise level of the measuring instrument ≤ 14dBµV @ 3m distance (5,500 – 14,500 MHz) Remark: *5 for using a pre-amplifier in the range between 100 kHz and 1,000 MHz Remark: *6 for using a pre-amplifier in the range between 4.0 GHz and 18.0 GHz The equipment meets the requirements Yes No N.t. Further test results are attached Yes No State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 31 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 11.6 Bandwidth (20 dB) 11.6.1 Regulation (c) The bandwidth of the emission shall be no wider than 0.25% of the center frequency for devices operating above 70 MHz and below 900 MHz. For devices operating above 900 MHz, the emission shall be no wider than 0.5% of the center frequency. Bandwidth is determined at the points 20 dB down from the modulated carrier. 11.6.2 Calculation of the 20 dB bandwidth limit The 20 dB bandwidth limit = 0.0025 * 315 MHz = 0.7875 MHz = 787.5 kHz 11.6.3 Test equipment Type Manufacturer/ Serial no. Last calibration Next calibration Model no. Receiver Hewlett Packard 3528U00990 2007/08 2009/08 Spectrum Analyzer (9 kHz –26.5 GHz) 8593E (171) Test fixture m.dudde --- Verification previous to the measurement hochfrequenz-technik 11.6.4 Test procedure ANSI C63.4-2003 Section 13.1.7 Occupied bandwidth measurements. The bandwidth is measured at an amplitude level reduced from the reference level by a specified ratio. The reference level is the level of the highest amplitude signal observed from the transmitter at either the fundamental frequency or first-order modulation products in all typical modes of operation, including the unmodulated carrier, even if atypical. Once the reference level is established, the equipment is conditioned with typical modulating signals to produce worst-case (i.e., the widest) bandwidth. In order to measure the modulated signal properly, a resolution bandwidth that is small compared to the bandwidth required by the procuring or regulatory agency shall be used on the measuring instrument. However, the 6 dB resolution bandwidth of the measuring instrument shall be set to a value greater than 5% of the bandwidth requirements. State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 32 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 11.6.5 Test result The measured 20 dB bandwidth is: One channel version, channel 1 75.0 kHz Three channel version, channel 1 90.0 kHz Three channel version, channel 2 91.2 kHz Three channel version, channel 3 90.0 kHz The equipment meets the requirements Yes No N.t. Further test results are attached Yes No Annex no: 3 State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 33 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 12. Additional information to the test report Remarks N.t.1 Not tested, because the antenna is part of the PCB N.t.2 Not tested, because the EUT is directly battery powered N.t.3 Not tested, because not applicable for this type of equipment State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920

Test report no. 08004786 Page 34 of 34 EUT: BR212 Key Basis Date of issue: 2008-06-03 FCC ID: IYZDC07 End of test report State: 2008-04-21 Vers. no.: 1. 08 m. dudde hochfrequenz - technik Rottland 5a D-51429 Bergisch Gladbach Tel. +49 2207-96890 Fax +49 2207 968920


Document Created: 2008-07-08 09:39:22
Document Modified: 2008-07-08 09:39:22
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC