Report

FCC ID: IYZDC02

Test Report

Download: PDF
FCCID_655693

Test Report No.: 05002824 Page 1 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 TTI-P-G-128/96 Test Report acc. to the relevant standard: 47 CFR Part 15 C – Intentional Radiators Measurement Procedure: ANSI C63.4 - 1992 relating to Marquardt GmbH Key DC_02 Measurement of Radio- Noise Emissions from Low- Voltage Electrical and Electronic Equipment Technical characteristics and test methods for radio equipment in the frequency range 9 kHz to 40 GHz m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 2 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 Manufacturer’s details Manufacturer Marquardt GmbH Manufacturers Grantee Code IYZ Manufacturers Address Schloßstrasse 16 D-78604 Rietheim Weilheim Germany Phone : +49 7424 99 1960 Fax : +49 7424 99 2419 E- Mail: andreas.gaebler@marquardt.de Relevant standard used 47 CFR Part 15C - Intentional Radiators ANSI C63.4-1992 Test report prepared by Technical engineer Ralf Trepper m.dudde hochfrequenz-technik (Labor) Rottland 5a D-51429 Bergisch Gladbach Germany Phone: +49 2207 96890 Fax : +49 2207 968920 E-mail: m.duddelabor@dudde.com Equipment Under Test (EUT) Equipment category Transmitter Trade name Marquardt Type designation DC_02 Serial no. --- Variants m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 3 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 0 Test result CFR Report Requirements Test result Section Chapter Headline OK 15.203 10.1 Antenna requirement pass fail n.a. 15.231 (b) 10.2 Field strength limits (fundamental) pass fail n.a. 15.205(b) 10.2 Radiated spurious emissions pass fail n.a. 15.209 15.231 (a) 10.3 Periodic operation characteristics pass fail n.a. 15.231 (c) 10.4 20 dB bandwidth pass fail n.a. Test requirements kept yes no . Signature Technician ........................................ Ralf Trepper . Signature Manager ......................................... Manfried Dudde m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 4 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 List of contents Page 0 Test result .............................................................................................................................................. 3 1 Testing laboratory .................................................................................................................................. 5 2 Introduction ........................................................................................................................................... 5 3 Product .................................................................................................................................................. 6 4 Test schedule ......................................................................................................................................... 6 5 Product and measurement documentation............................................................................................... 7 6 Observations and comments................................................................................................................... 7 7 Summary ............................................................................................................................................... 7 8 Conclusions .......................................................................................................................................... 8 9 Operation description............................................................................................................................. 9 10.1 Antenna requirement ......................................................................................................................... 10 10.1.1 Regulation ...................................................................................................................................... 10 10.1.2 Result ............................................................................................................................................. 10 10.2 Radiated emissions ........................................................................................................................... 11 10.2.1 Regulation ...................................................................................................................................... 11 10.2.2 Test equipment ............................................................................................................................... 12 10.2.2.1 Test procedures............................................................................................................................ 12 10.2.3 Calculation of field strength limits.................................................................................................. 13 10.2.4 Calculation of average correction factor.......................................................................................... 13 10.2.5 Calculation of the field strengths .................................................................................................... 13 10.2.6 Result ............................................................................................................................................. 14 10.3.1 Periodic operation........................................................................................................................... 16 10.3.1.1 Regulation ................................................................................................................................... 16 10.3.1.2 Result .......................................................................................................................................... 16 10.3.2 Manually operated transmitter deactivation .................................................................................... 16 10.3.2.1 Regulation ................................................................................................................................... 16 10.3.2.2 Result .......................................................................................................................................... 16 10.3.3 Automatically operated transmitter deactivation ............................................................................. 16 10.3.3.1 Regulation ................................................................................................................................... 16 10.3.3.2 Result .......................................................................................................................................... 16 10.3.4 Prohibition of periodic transmission ............................................................................................... 17 10.3.4.1 Regulation ................................................................................................................................... 17 10.3.4.2 Result .......................................................................................................................................... 17 10.3.5 Continuous transmission during an alarm condition........................................................................ 17 10.3.5.1 Regulation ................................................................................................................................... 17 10.3.5.2 Result .......................................................................................................................................... 17 10.4 Bandwidth ........................................................................................................................................ 18 10.4.1 Regulation ...................................................................................................................................... 18 10.4.2 Calculation of the 20 dB bandwidth limit ....................................................................................... 18 10.4.3 Test equipment ............................................................................................................................... 18 10.4.4 Test procedure ................................................................................................................................ 18 10.4.5 Test result ....................................................................................................................................... 19 11 Additional information to this test report .............................................................................................. 20 m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 5 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 1 Testing laboratory Company Name : m.dudde high frequency technology Street : Rottland 5a City : 51429 Bergisch Gladbach Country : Germany Laboratory : FCC Registration Number: 699717 This site has been fully described in a report submitted to the FCC, and accepted in the letter dated Registration Number .699717 Phone : +49-2207-9689-0 Fax : +49-2207-9689-20 E-Mail : manfred.dudde@t-online.de Web : http://www.dudde.com 2 Introduction The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of m. dudde hochfrequenz - technik. This report contains the result of tests performed by m. dudde hochfrequenz - technik for the purpose of a type approval. The order for carrying out these tests had been placed by: Manufacturer Company name : Marquardt GmbH Address : Schloßstrasse 16 Postcode : D-78604 City/town : Rietheim-Weilheim Country : Germany Telephone : +49 7424 99 1960 Telefax : +49 7442 99 2419 E-Mail : andreas.gaebler@marquardt.de Date of order : 2005-11-09 References : Mr. Andreas Gäbler m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 6 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 3 Product Samples of the following apparatus were submitted for testing: Type of equipment : Transmitter Trademark : Marquardt Type designation : DC_02 Hardware version : DC_02 Serial number : --- Software release : --- Equipment used power : 6.0VDC Frequency used : 315 MHz Generated or used frequencies : 9.84375 MHz FCC ID : IYZDC02 4 Test schedule Tests were carried out in accordance with the specifications detailed in chapter 7 “Summary“of this report. Tests were carried out at: - m. dudde hochfrequenz - technik, D-51429 Bergisch Gladbach The test sample was received on: - 2005-11-09 The tests were carried out in the following period of time: - 2005-11-14 - 2005-11-21 m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 7 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 5 Product and measurement documentation For issuing this report the following product documentation was used and the following annexes were created: Description Date Identifications External photographs of the Equipment Under Test 2005-11-23 Annex No. 1 Internal photographs of the Equipment Under Test 2005-11-23 Annex No. 2 Occupied bandwidth plot 2005-11-23 Annex No. 3 FCC ID label sample 2005-11-23 Annex No. 4 Functional description 2005-11-23 Annex No. 5 Test setup photos 2005-11-23 Annex No. 6 Block diagram 2005-11-23 Annex No. 7 Schematics 2005-11-23 Annex No. 8 Periodic operation characteristics 2005-11-23 Annex No. 9 The above mentioned documentation will be filed at m. dudde hochfrequenz - technik for a period of 10 years following the issue of this report. 6 Observations and comments 7 Summary The product is intended for the use in the following areas of application: Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the frequency range of 9 kHz to 40 GHz The samples were tested according to the following specification: 47 CFR Part 15 – Intentional Radiators, ANSI C63.4 - 1992 m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 8 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 8 Conclusions Samples of the apparatus were found to CONFORM WITH the specifications stated in chapter 7 "Summary" of this report. In the opinion of m. dudde hochfrequenz - technik, the samples satisfied all applicable requirements relating to the network interface types specified in chapter 7 "Summary". The results of the type tests as stated in this report are exclusively applicable to the product item as identified in this report. m. dudde hochfrequenz - technik does not accept any responsibility for the results stated in this report, with respect to the properties of product items not involved in these tests. This report consists of a main module, modules with test results and annexes listed in chapter 5: “Product documentation”. All pages have been numbered consecutively and bear the m. dudde hochfrequenz - technik logo, the report number and sub numbers. The total number of pages in this report is 21. Tester: Date : 2005-11-23 Name : Ralf Trepper Signature : Technical responsibility for area of testing: Date : 2004-11-23 Name : Manfried Dudde Signature : m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 9 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 9 Operation description 9.1 EUT details The DC_02 key is a component of a driver authorisation system and has the following function: Remote control for vehicle access via radio and infrared signals. A command is transmitted to the vehicle by the key via a HF transmitter after a button has been pressed on the key. 9.2 EUT configuration see Annex No 5 (Functional description) 9.3 EUT measurement description The Key DC_02 was tested in a typical fashion.. During preliminary emission tests the Key DC_02 was operated in continuous transmitting mode for worst case emission mode investigation. Therefore, final qualification testing was completed with Key DC_02 operated in all continuous modes. All tests performed with applicant typical voltage (6 Volts DC). m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 10 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 10.1 Antenna requirement 10.1.1 Regulation 15.203 An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of Part 15C. The manufacturer may design the unit so that the user can replace a broken antenna, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier current devices or to devices operated under the provisions of Sections 15.211, 15.213, 15.217, 15.219, or 15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional radiators which, in accordance with Section 15.31 (d), must be measured at the installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed so that the limits in this Part are not exceeded. 10.1.2 Result The equipment meets the requirements yes no n.a. Further test results are attached yes no page no: n.a x see page no. 20 m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 11 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 10.2 Radiated emissions 10.2.1 Regulation Test requirement: FCC CFR47, Part 15C Test procedure: ANSI C63.4:1992 Fundamental frequency Field strength of fundamental Field strength of spurious emissions (MHz) (microvolts/meter) (microvolts/meter) 40.66 - 40.70 2,250 225 70-130 1,250 125 130-174 1,250 to 3,750 125 to 375 174-260 3,750 375 260-470 3,750 to 12,500 375 to 1,250 Above 470 12,500 1,250 ** Linear interpolations [Where F is the frequency in MHz, the formulas for calculating the maximum permitted fundamental field strengths are as follows: for the band 130-174 MHz, µV/m at 3 meters = 56.81818(F) - 6136.3636; for the band 260-470 MHz, µV/m at 3 meters = 41.6667(F) - 7083.3333. The maximum permitted unwanted emission level is 20 dB below the maximum permitted fundamental level.] (1) The above field strength limits are specified at a distance of 3 meters. The tighter limits apply at the band edges. (2) Intentional radiators operating under the provisions of this Section shall demonstrate compliance with the limits on the field strength of emissions, as shown in the above table, based on the average value of the measured emissions. As an alternative, compliance with the limits in the above table may be based on the use of measurement instrumentation with a CISPR quasi-peak detector. The specific method of measurement employed shall be specified in the application for equipment authorization. If average emission measurements are employed, the provisions in Section 15.35 for averaging pulsed emissions and for limiting peak emissions apply. Further, compliance with the provisions of Section 15.205 shall be demonstrated using the measurement instrumentation specified in that section. (3) The limits on the field strength of the spurious emissions in the above table are based on the fundamental frequency of the intentional radiator. Spurious emissions shall be attenuated to the average (or, alternatively, CISPR quasi-peak) limits shown in this table or to the general limits shown in Section 15.209, whichever limit permits a higher field strength. Section 15.33 Frequency range of radiated measurements: (a) Unless otherwise noted in the specific rule section under which the equipment operates for an intentional radiator the spectrum shall be investigated from the lowest radio frequency signal generated in the device, without going below 9 kHz, up to at least the frequency shown in this paragraph: (1 ). If the intentional radiator operates below 10 GHz: to the tenth harmonic of the highest fundamental frequency or to 40 GHz, whichever is lower. m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 12 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 10.2.2 Test equipment Type Manufacturer/ Serial no. Last calibration Next calibration Model No. Receiver Hewlett Packard 3528U00990 2004/02 2006/02 Spectrum Analyzer (9 kHz –26.5 GHz) 8593E (171) Pre-amplifier Hewlett Packard 1726A00705 2002/04 2006/04 (100kHz - 1.3GHz) 8447 E (166a) Bilog antenna CHASE 1517 2002/04 2008/04 (30- 1000 MHz) CBL611A (167) Horn antenna Schwarzbeck 236 1998/01 2008/01 (0,86-8,5 GHz) BBHA 9120 A (284) 10.2.2.1 Test procedures The EUT and this peripheral (when additional equipment exist) are placed on a turn table which is 0.8m above the ground. The turn table would be allowed to rotate 360 degrees to determine the position of the maximum emission level. The test distance between the EUT and the receiving antenna are 3m. To find the maximum emission, the polarization of the receiving antenna are changed in horizontal and vertical polarization, the position of the EUT was changed in different orthogonal determinations. ANSI C63.4: 1992 Section 8 “Radiated Emissions Testing” Radiated emissions test characteristics Frequency range 30 MHz - 4,000 MHz Test distance 3 m* Test instrumentation resolution bandwidth 120 kHz (30 MHz - 1,000 MHz) 1 MHz (1000 MHz - 4,000 MHz) Receive antenna scan height 1m-4m Receive antenna polarization Vertical/horizontal * According to Section 15.31 (f)(1): At frequencies at or above 30 MHz, measurements may be performed at a distance other than what is specified provided: measurements are not made in the near field except where it can be shown that near field measurements are appropriate due to the characteristics of the device; and it can be demonstrated that the signal levels needed to be measured at the distance employed can be detected by the measurement equipment. When performing measurements at a distance other than that specified, the results shall be extrapolated to the specified distance using an extrapolation factor of 20 dB/decade (inverse linear-distance for field strength measurements; inverse-linear-distance-squared for power density measurements). m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 13 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 10.2.3 Calculation of field strength limits For example: Transmitter working on 315 MHz Limit for average measurements → 41.6667*(315 MHz) – 7083.3333 = 6041.677µV/m = 75.6dBµV/m @3m Limit for peak measurements → Limit for average measurements + 20dB = 95.6dBµV/m @3m 10.2.4 Calculation of average correction factor The average correction factor is computed by analyzing the "worst case" on time in any 100msec time period and using the formula: Corrections Factor + 20*log (worst case on time/100msec). Analysis of the remote transmitter worst case on time in any 100msec time period is an on time of 50msec, therefore the correction factor is 20*log (50/100) = - 6 dB. The maximum correction factor to be applied is 20 dB per section 15.35 of the FCC rules. 10.2.5 Calculation of the field strengths The field strength is calculated by the following calculation: Corrected Level = Receiver Level + Correction Factor (without the use of an pre-amplifier) Corrected Level = Receiver Level + Correction Factor – Pre-Amplifier (with the use of an pre-amplifier) Receiver Level : Receiver reading without correction factors Correction Factor : Antenna factor + cable loss For example: The receiver reading is 32.7 dBµV. The antenna factor for the measured frequency is +2.5 dB(1/m) and the cable factor for the measured frequency is 0.71 dB, giving a field strength of 35.91dBµV/m. The 35.91dBµV/m value can be mathematically converted to its corresponding level in µV/m. Level in µV/m = Common Antilogarithm (35.91/20) = 39.8 For test distance other than what is specified, but fulfilling the requirements of Section 15.31 (f)(1) the field strength is calculated by adding additionally an extrapolation factor of 20 dB/decade (inverse linear distance for field strength measurements). m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 14 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 10.2.6 Result TRANSMITTER SPURIOUS RADIATION (Section 15.231(b)) Polarisation Antenna f Bandwidth Noted Test Correction Distance Level Limit Margin EUT height (MHz) (kHz) / receiver level distance factor extrapol. corrected / Type factor antenna of detector dBµV m dB dB dBµV/m dBµV/m dBµV/m cm 315.01363 120 / QPK 3 -7.50 75.6 73.56 0 66.1 9.5 V/V 149 120 / AV 3 -7.50 75.6 73.52 0 66.0 9.6 V/V 149 630.02726 120 / QPK 3 -1.90 55.6 46.51 0 44.6 11.0 V/V 142 120 / AV 3 -1.90 55.6 46.47 0 44.6 11.0 V/V 142 945.04089 120 / QPK 3 +1.20 55.6 32.21 0 33.4 22.2 V/V 191 120 / AV 3 +1.20 55.6 30.88 0 32.1 23.5 V/V 191 1260.05452 1000 / AV 3 +29.7 55.6 10.47 0 40.2 15.4 V/V 147 1575.06815 1000 / AV 3 +25.63 55.6 10.19 0 35.8 19.8 V/V 118 1890.08178 1000 / AV 3 +26.57 55.6 9.10 0 35.7 19.9 V/V 183 2205.09541 1000 / AV +27.27 54.0 < 10 3 0 37.27 16.73 H,V/H,V 100-400 2520.10904 1000 / AV +27.82 55.6 < 10 3 0 37.82 17.78 H,V/H,V 100-400 2835.12267 1000 / AV +28.07 54.0 < 10 3 0 38.07 15.93 H,V/H,V 100-400 3150.13630 1000 / AV +28.59 55.6 < 10 3 0 38.57 17.03 H,V/H,V 100-400 3465.14993 1000 / AV +29.41 55.6 < 10 3 0 39.41 16.19 H,V/H,V 100-400 3 3 Measurement uncertainty 4 dB * Bandwidth = the measuring receiver bandwidth Remark: *1 noise floor noise level of the measuring instrument ≤ 3.5dBµV @ 3m distance (30 – 1,000 MHz) Remark: *2 noise floor noise level of the measuring instrument ≤ 4.5 dBµV @ 3m distance (1,000 – 2,000 MHz) Remark: *3 noise floor noise level of the measuring instrument ≤ 10 dBµV @ 3m distance (2,000 – 5,500 MHz) Remark: *4 noise floor noise level of the measuring instrument ≤ 14 dBµV @ 3m distance (5,500 – 14,500 MHz) Remark: *5 for using a pre-amplifier in the range between 100 kHz and 1,000 MHz Remark: *6 for using a pre-amplifier in the range between 4.0 GHz and 18.0 GHz The equipment meets the requirements yes no n.a. Further test results are attached yes no n.a x see page no. 23 m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 15 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 TRANSMITTER SPURIOUS RADIATION ABOVE 30 MHz (Section 15.205, 15.209) AV Polaris. Antenna f Bandwidth Noted Test Correction Distance Level Limit Margin Correction EUT height (MHz) (kHz) receiver distance factor extrapol. corrected factor / Type level factor antenna of detector dBµV m dB dB dBµV/m dBµV/m dBµV/m dB cm 30.0000 100, AV ≤ 3.5 3 -2.60 0 0 0.90 40.00 39.10 H,V/H,V 100-400 88.0000 100, AV ≤ 3.5 3 -10.80 0 0 -7.30 40.00 47.30 H,V/H,V 100-400 216.0000 100, AV ≤ 3.5 3 -10.30 0 0 -6.80 43.50 50.30 H,V/H,V 100-400 960.0000 100, AV ≤ 3.5 3 8.50 0 0 12.00 43.50 31.50 H,V/H,V 100-400 1700.0000 1000, AV ≤ 4.5 3 3.80 0 0 8.30 54.00 45.70 H,V/H,V 100-400 2250.0000 1000, AV ≤ 10 3 8.00 0 0 18.00 54.00 36.00 H,V/H,V 100-400 4000.0000 1000, AV ≤ 10 3 6 0 0 18.40 54.00 35.60 H,V/H,V 100-400 8.40* 5000.0000 1000, AV ≤ 10 3 6 0 0 19.40 54.00 34.60 H,V/H,V 100-400 9.10* 7500.0000 1000, AV ≤ 14 3 6 0 0 26.90 54.00 27.10 H,V/H,V 100-400 12.9* 0 8300.0000 1000, AV ≤ 14 3 6 0 0 28.80 54.00 25.20 H,V/H,V 100-400 14.80* 9400.0000 1000, AV ≤ 14 3 6 0 0 30.00 54.00 24.00 H,V/H,V 100-400 16.00* 11000.0000 1000, AV ≤ 14 3 6 0 0 32.25 54.00 21.75 H,V/H,V 100-400 18.25* Measurement uncertainty 4 dB * Bandwidth = the measuring receiver bandwidth Remark: *1 noise floor noise level of the measuring instrument ≤ 3.5dBµV @ 3m distance (30 – 1,000 MHz) Remark: *2 noise floor noise level of the measuring instrument ≤ 4.5 dBµV @ 3m distance (1,000 – 2,000 MHz) Remark: *3 noise floor noise level of the measuring instrument ≤ 10 dBµV @ 3m distance (2,000 – 5,500 MHz) Remark: *4 noise floor noise level of the measuring instrument ≤ 14 dBµV @ 3m distance (5,500 – 14,500 MHz) Remark: *5 for using a pre-amplifier in the range between 100 kHz and 1,000 MHz Remark: *6 for using a pre-amplifier in the range between 4.0 GHz and 18.0 GHz The equipment meets the requirements yes no n.a. Further test results are attached yes no page no: n.a x see page no. 23 m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 16 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 10.3 Periodic operation characteristics 10.3.1 Periodic operation 10.3.1.1 Regulation 15.231 (a) The provisions of this Section are restricted to periodic operation within the band 40.66 40.70 MHz and above 70 MHz. Except as shown in paragraph (e) of this Section, the intentional radiator is restricted to the transmission of a control signal such as those used with alarm systems, door openers, remote switches, etc. Radio control of toys is not permitted. Continuous transmissions, such as voice or video, and data transmissions are not permitted. The prohibition against data transmissions does not preclude the use of recognition codes. Those codes are used to identify the sensor that is activated or to identify the particular component as being part of the system. 10.3.1.2 Result The equipment meets the requirements yes no n.a. Further test results are attached yes no Annex no: 5 10.3.2 Manually operated transmitter deactivation 10.3.2.1 Regulation 15.231 (a1) A manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released 10.3.2.2 Result The equipment meets the requirements yes no n.a. Further test results are attached yes no Annex no: 9 10.3.3 Automatically operated transmitter deactivation 10.3.3.1 Regulation 15.231 (a2) A transmitter activated automatically shall cease transmission within 5 seconds after activation. 10.3.3.2 Result The equipment meets the requirements yes no n.a. Further test results are attached yes no page no: m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 17 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 10.3.4 Prohibition of periodic transmission 10.3.4.1 Regulation 15.231 (a3) Periodic transmissions at regular predetermined intervals are not permitted. However, polling or supervision transmissions to determine system integrity of transmitters used in security or safety applications are allowed if the periodic rate of transmission does not exceed one transmission of not more than one second duration per hour for each transmitter. 10.3.4.2 Result The equipment meets the requirements yes no n.a. Further test results are attached yes no page no: 10.3.5 Continuous transmission during an alarm condition 10.3.5.1 Regulation 15.231 (a4) Intentional radiators which are employed for radio control purposes during emergencies involving fire, security, and safety of life, when activated to signal an alarm, may operate during the pendency of the alarm condition. 10.3.5.2 Result The equipment meets the requirements yes no n.a. Further test results are attached yes no page no: m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 18 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 10.4 Bandwidth 10.4.1 Regulation 15.231 (c) The bandwidth of the emission shall be no wider than 0.25% of the centre frequency for devices operating above 70 MHz and below 900 MHz. For devices operating above 900 MHz, the emission shall be no wider than 0.5% of the centre frequency. Bandwidth is determined at the points 20 dB down from the modulated carrier. 10.4.2 Calculation of the 20 dB bandwidth limit The 20 dB bandwidth limit = 0.0025 * 315 MHz = 0.7875 MHz = 787.5 kHz 10.4.3 Test equipment Type Manufacturer/ Serial no. Last calibration Next calibration Model no. Receiver Hewlett Packard 3528U00990 2004/02 2006/02 (30MHz - 1GHz) Spectrum Analyzer (171) 8593 E Test fixture Dudde --- 10.4.4 Test procedure ANSI C63.4-1992 Section 13.1.7 Occupied bandwidth measurements. The bandwidth is measured at an amplitude level reduced from the reference level by a specified ratio. The reference level is the level of the highest amplitude signal observed from the transmitter at either the fundamental frequency or first-order modulation products in all typical modes of operation, including the unmodulated carrier, even if atypical. Once the reference level is established, the equipment is conditioned with typical modulating signals to produce worst-case (i.e., the widest) bandwidth. In order to measure the modulated signal properly, a resolution bandwidth that is small compared to the bandwidth required by the procuring or regulatory agency shall be used on the measuring instrument. However, the 6 dB resolution bandwidth of the measuring instrument shall be set to a value greater than 5% of the bandwidth requirements. m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 19 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 10.4.5 Test result The measured 20 dB bandwidth is: .................93.70 kHz The equipment meets the requirements yes no n.a. Further test results are attached yes no Annex no: 3 m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 20 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 11 Additional information to this test report Remarks n.a.1 not applicable, because the antenna is part of the PCB n.a.2 not applicable, because the EUT is directly battery powered m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com

Test Report No.: 05002824 Page 21 of 21 EUT: DC_02 FCC ID: IYZDC02 Date of issue: 2005-11-23 End of test report m. dudde hochfrequenz-technik Rottland 5a Vers. date: 2004-08 D-51429 Bergisch Gladbach Tel.: +49 2207-9689-0 Fax: +49 2207 9689-20 e-mail: manfred.dudde@t-online.de http://www.dudde.com


Document Created: 2006-03-16 16:34:38
Document Modified: 2006-03-16 16:34:38
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC