Test Report

FCC ID: IYZDAG16

Test Report

Download: PDF

FCCID_3912510

Test report no.: 1-3501/17-02-05

1 Table of contents

1 Table of contents ............................................................................................................................................ 2
2 General information ....................................................................................................................................... 3
2.1 Notes and disclaimer .......................................................................................................................... 3
2.2 Application details ............................................................................................................................... 3
2.3 Test laboratories sub-contracted ...................................................................................................... 3
3 Test standard/s and references .................................................................................................................... 4
4 Test environment............................................................................................................................................ 5
5 Test item .......................................................................................................................................................... 5
5.1 General description ............................................................................................................................. 5
5.2 Additional information ........................................................................................................................ 5
6 Description of the test setup ......................................................................................................................... 6
6.1 Shielded semi anechoic chamber ...................................................................................................... 7
6.2 Shielded fully anechoic chamber ...................................................................................................... 8
6.3 RF measurements normal and extreme conditions ......................................................................... 9
7 Sequence of testing .....................................................................................................................................10
7.1 Sequence of testing radiated spurious 9 kHz to 30 MHz ...............................................................10
7.2 Sequence of testing radiated spurious 30 MHz to 1 GHz ..............................................................11
8 Measurement uncertainty ............................................................................................................................12
9 Summary of measurement results .............................................................................................................13
10 Additional comments ...............................................................................................................................13
11 Measurement results ................................................................................................................................14
11.1 Occupied bandwidth......................................................................................................................14
11.2 Field strength of the fundamental ................................................................................................16
11.3 Field strength of the harmonics and spurious ...........................................................................17
12 Observations .............................................................................................................................................20
Annex A Glossary ..........................................................................................................................................21
Annex B Document history ..........................................................................................................................22
Annex C Accreditation Certificate ...............................................................................................................22

© CTC advanced GmbH Page 2 of 22

Test report no.: 1-3501/17-02-05

2 General information

2.1 Notes and disclaimer
The test results of this test report relate exclusively to the test item specified in this test report. CTC advanced
GmbH does not assume responsibility for any conclusions and generalizations drawn from the test results with
regard to other specimens or samples of the type of the equipment represented by the test item.
The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report
requires the prior written approval of CTC advanced GmbH.
The testing service provided by CTC advanced GmbH has been rendered under the current "General Terms and
Conditions for CTC advanced GmbH".
CTC advanced GmbH will not be liable for any loss or damage resulting from false, inaccurate, inappropriate or
incomplete product information provided by the customer.
Under no circumstances does the CTC advanced GmbH test report include any endorsement or warranty
regarding the functionality, quality or performance of any other product or service provided.
Under no circumstances does the CTC advanced GmbH test report include or imply any product or service
warranties from CTC advanced GmbH, including, without limitation, any implied warranties of merchantability,
fitness for purpose, or non-infringement, all of which are expressly disclaimed by CTC advanced GmbH.
All rights and remedies regarding vendor’s products and services for which CTC advanced GmbH has prepared
this test report shall be provided by the party offering such products or services and not by CTC advanced GmbH.
In no case this test report can be considered as a Letter of Approval.

This test report is electronically signed and valid without handwritten signature. For verification of the electronic
signatures, the public keys can be requested at the testing laboratory.

2.2 Application details
Date of receipt of order: 2018-01-11
Date of receipt of test item: 2018-01-11
Start of test: 2018-03-21
End of test: 2018-03-22
Person(s) present during the test: -/-

2.3 Test laboratories sub-contracted
None

© CTC advanced GmbH Page 3 of 22

Test report no.: 1-3501/17-02-05

4 Test environment

Tnom +22 °C during room temperature tests
Temperature : Tmax +85 °C during high temperature tests
Tmin -40 °C during low temperature tests
Relative humidity content : 43 %
Barometric pressure : 1019 hpa
Vnom 24 V DC by external power supply
Power supply : Vmax 32 V
Vmin 10 V

5 Test item

5.1 General description

Kind of test item : Body Control Module
Type identification : DAG16
HMN : -/-
PMN : DAG16
HVIN : DAG16
FVIN : -/-
S/N serial number : 243.203.011-02
HW hardware status : 17/42/01
SW software status : EIS02T
Frequency band : 21.85 kHz
Type of radio transmission :
Modulated carrier
Use of frequency spectrum :
Type of modulation : TBD
Number of channels : 1
Antenna : External antenna
Power supply : 10 V to 32 V DC by external power supply
Temperature range : -40°C to +85°C

5.2 Additional information
The content of the following annexes is defined in the QA. It may be that not all of the listed annexes are
necessary for this report, thus some values in between may be missing.

Test setup- and EUT-photos are included in test report: 1-3501/17-02-01_AnnexA
1-3501/17-02-01_AnnexB
1-3501/17-02-01_AnnexD

© CTC advanced GmbH Page 5 of 22

Test report no.: 1-3501/17-02-05

6 Description of the test setup
Typically, the calibrations of the test apparatus are commissioned to and performed by an accredited calibration
laboratory. The calibration intervals are determined in accordance with the DIN EN ISO/IEC 17025. In addition to
the external calibrations, the laboratory executes comparison measurements with other calibrated test systems
or effective verifications. Weekly chamber inspections and range calibrations are performed. Where possible, RF
generating and signaling equipment as well as measuring receivers and analyzers are connected to an external
high-precision 10 MHz reference (GPS-based or rubidium frequency standard).

In order to simplify the identification of the equipment used at some special tests, some items of test equipment
and ancillaries can be provided with an identifier or number in the equipment list below (Lab/Item).

Agenda: Kind of Calibration

k calibration / calibrated EK limited calibration
ne not required (k, ev, izw, zw not required) zw cyclical maintenance (external cyclical
maintenance)
ev periodic self verification izw internal cyclical maintenance
Ve long-term stability recognized g blocked for accredited testing
vlkI! Attention: extended calibration interval
NK! Attention: not calibrated *) next calibration ordered / currently in progress

© CTC advanced GmbH Page 6 of 22

Test report no.: 1-3501/17-02-05

7 Sequence of testing

7.1 Sequence of testing radiated spurious 9 kHz to 30 MHz
Setup
• The equipment is set up to simulate normal operation mode as described in the user manual or defined
by the manufacturer.
• If the EUT is a tabletop system, it is placed on a table with 0.8 m height.
• If the EUT is a floor standing device, it is placed directly on the turn table.
• Auxiliary equipment and cables are positioned to simulate normal operation conditions as described in
ANSI C 63.4.
• The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
• Measurement distance is 3 m (see ANSI C 63.4) – see test details.
• EUT is set into operation.

Premeasurement*
• The turntable rotates from 0° to 315° using 45° steps.
• The antenna height is 1 m.
• At each turntable position the analyzer sweeps with positive-peak detector to find the maximum of all
emissions.

Final measurement
• Identified emissions during the pre-measurement are maximized by the software by rotating the turntable
from 0° to 360°.
• Loop antenna is rotated about its vertical axis for maximum response at each azimuth about the EUT.
(For certain applications, the loop antenna plane may also need to be positioned horizontally at the
specified distance from the EUT)
• The final measurement is done in the position (turntable and elevation) causing the highest emissions
with quasi-peak (as described in ANSI C 63.4).
• Final levels, frequency, measuring time, bandwidth, turntable position, correction factor, margin to the
limit and limit will be recorded. A plot with the graph of the premeasurement and the limit is stored.

*)Note: The sequence will be repeated three times with different EUT orientations.

© CTC advanced GmbH Page 10 of 22

Test report no.: 1-3501/17-02-05

7.2 Sequence of testing radiated spurious 30 MHz to 1 GHz
Setup
• The equipment is set up to simulate normal operation mode as described in the user manual or defined
by the manufacturer.
• If the EUT is a tabletop system, a table with 0.8 m height is used, which is placed on the ground plane.
• If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
• Auxiliary equipment and cables are positioned to simulate normal operation conditions as described in
ANSI C 63.4.
• The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
• Measurement distance is 10 m or 3 m (see ANSI C 63.4) – see test details.
• EUT is set into operation.

Premeasurement
• The turntable rotates from 0° to 315° using 45° steps.
• The antenna is polarized vertical and horizontal.
• The antenna height changes from 1 m to 3 m.
• At each turntable position, antenna polarization and height the analyzer sweeps three times in peak to
find the maximum of all emissions.

Final measurement
• The final measurement is performed for at least six highest peaks according to the requirements of the
ANSI C63.4.
• Based on antenna and turntable positions at which the peak values are measured the software maximize
the peaks by changing turntable position ± 45° and antenna height between 1 and 4 m.
• The final measurement is done with quasi-peak detector (as described in ANSI C 63.4).
• Final levels, frequency, measuring time, bandwidth, antenna height, antenna polarization, turntable angle,
correction factor, margin to the limit and limit are recorded. A plot with the graph of the premeasurement
with marked maximum final results and the limit is stored.

© CTC advanced GmbH Page 11 of 22

Test report no.: 1-3501/17-02-05

8 Measurement uncertainty

Measurement uncertainty
Test case Uncertainty
Occupied bandwidth ± used RBW
Field strength of the fundamental ± 3 dB
Field strength of the harmonics and spurious ± 3 dB
Receiver spurious emissions and cabinet radiations ± 3 dB
Conducted limits ± 2.6 dB

© CTC advanced GmbH Page 12 of 22

Test report no.: 1-3501/17-02-05

11 Measurement results

11.1 Occupied bandwidth
Measurement:

The emission bandwidth (x dB) is defined as the frequency range between two points, one above and one
below the carrier frequency, at which the spectral density of the emission is attenuated x dB below the
maximum in-band spectral density of the modulated signal.

Measurement parameters
Detector: Peak
Resolution bandwidth: 1 % – 5 % of the occupied bandwidth
Video bandwidth: ≥ 3x RBW
Trace mode: Max hold
Analyser function: 99 % power function
Used test setup: See chapter 6.3 A
Measurement uncertainty: See chapter 8

Limit:

IC
for RSP-100 test report coversheet only

Result:

99% emission bandwidth
65.0 kHz

© CTC advanced GmbH Page 14 of 22

Test report no.: 1-3501/17-02-05

11.2 Field strength of the fundamental
Measurement:

The maximum detected field strength for the carrier signal.

Measurement parameters
Detector: Quasi peak / peak (worst case)
Resolution bandwidth: 9 kHz
Video bandwidth: ≥ 3x RBW
Trace mode: Max hold
Used test setup See chapter 6.2 A
Measurement uncertainty: See chapter 8

Limit:

FCC & IC
Frequency Measurement distance
Field strength
(MHz) (m)
0.009-0.490 2400/F(kHz)* = 109.8 µV/m = 40.8 dBµV/m 300
*F(kHz) = 21.85

Recalculation:

According to ANSI C63.10
Correction value
Frequency Formula
(from 3 m to 300 m)
𝑑𝑑𝑙𝑙𝑙𝑙𝑙𝑙𝑙𝑙𝑙𝑙
FSlimit = FSmax −40 log � �
𝑑𝑑𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚𝑚

FSlimit is the calculation of field strength at the limit distance,
21.85 kHz expressed in dBµV/m -80 dB
FSmax is the measured field strength, expressed in dBµV/m
dnear field is the λ/2π distance
dmeasure is the distance of the measurement point from EUT
dlimit is the reference limit distance

Result:

Field strength of the fundamental (dBµV / m)
Frequency 21.85 kHz
Distance @3m @ 300 m
Measured / calculated value
117.1 37.1
(peak measurement)
Measured / calculated value
115.1 35.1
(QP measurement)

© CTC advanced GmbH Page 16 of 22

Test report no.: 1-3501/17-02-05

11.3 Field strength of the harmonics and spurious
Measurement:

The maximum detected field strength for the harmonics and spurious.

Measurement parameters
Quasi peak / average or
Detector:
peak (worst case – pre-scan)
F < 150 kHz: 200 Hz
Resolution bandwidth: 150 kHz < F < 30 MHz: 9 kHz
30 MHz < F < 1 GHz: 120 kHz
F < 150 kHz: 1 kHz
Video bandwidth: 150 kHz < F < 30 MHz: 100 kHz
30 MHz < F < 1 GHz: 300 kHz
Trace mode: Max hold
9 kHz to 30 MHz: see chapter 6.2 A
Used test setup:
30 MHz to 1 GHz: see chapter 6.1 A
Measurement uncertainty: See sub clause 8

Limit:

FCC & IC
Frequency Field strength Measurement distance
(MHz) (dBµV/m) (m)
0.009 – 0.490 2400/F(kHz) 300
0.490 – 1.705 24000/F(kHz) 30
1.705 – 30 30 (29.5 dBµV/m) 30
30 – 88 100 (40 dBµV/m) 3
88 – 216 150 (43.5 dBµV/m) 3
216 – 960 200 (46 dBµV/m) 3

Result:

Detected emissions
Frequency Resolution bandwidth Detected value
Detector
(MHz) (kHz) (dBµV / m)
0.720 Quasi peak 9 43.4

© CTC advanced GmbH Page 17 of 22

Test report no.: 1-3501/17-02-05

Plots:

Plot 1: 9 kHz – 30 MHz, magnetic emissions
130
dBµV/m
120

110

100

90

80

70

60

50

40

30

20

10

0
9kHz 100k 1M 10M 30MHz
Frequency

© CTC advanced GmbH Page 18 of 22

Test report no.: 1-3501/17-02-05

Plot 2: 30 MHz – 1 GHz

60

55

50

45 FCC_10m_B

40
Level in dBµV/m

35

30

25

20

15

10

5

0
30M 50 60 80 100M 200 300 400 500 800 1,05G
Frequency in Hz

Meas.
Frequency QuasiPeak Limit Margin Bandwidth Height Azimuth Corr.
Time Pol
(MHz) (dBµV/m) (dBµV/m) (dB) (kHz) (cm) (deg) (dB)
(ms)
38.494 22.53 30.0 7.47 1000 120 172.0 V 210.0 13.1
44.097 23.05 30.0 6.95 1000 120 100.0 V 60.0 13.6
47.298 24.10 30.0 5.90 1000 120 100.0 V 31.0 13.7
49.814 21.26 30.0 8.74 1000 120 200.0 V 219.0 13.7
71.547 20.44 30.0 9.56 1000 120 203.0 V 232.0 9.5
78.561 24.52 30.0 5.48 1000 120 273.0 V 173.0 8.3

© CTC advanced GmbH Page 19 of 22

Test report no.: 1-3501/17-02-05

12 Observations
No observations except those reported with the single test cases have been made.

© CTC advanced GmbH Page 20 of 22

Test report no.: 1-3501/17-02-05

Annex A Glossary

EUT Equipment under test
DUT Device under test
UUT Unit under test
GUE GNSS User Equipment
ETSI European Telecommunications Standards Institute
EN European Standard
FCC Federal Communications Commission
FCC ID Company Identifier at FCC
IC Industry Canada
PMN Product marketing name
HMN Host marketing name
HVIN Hardware version identification number
FVIN Firmware version identification number
EMC Electromagnetic Compatibility
HW Hardware
SW Software
Inv. No. Inventory number
S/N or SN Serial number
C Compliant
NC Not compliant
NA Not applicable
NP Not performed
PP Positive peak
QP Quasi peak
AVG Average
OC Operating channel
OCW Operating channel bandwidth
OBW Occupied bandwidth
OOB Out of band
DFS Dynamic frequency selection
CAC Channel availability check
OP Occupancy period
NOP Non occupancy period
DC Duty cycle
PER Packet error rate
CW Clean wave
MC Modulated carrier
WLAN Wireless local area network
RLAN Radio local area network
DSSS Dynamic sequence spread spectrum
OFDM Orthogonal frequency division multiplexing
FHSS Frequency hopping spread spectrum
GNSS Global Navigation Satellite System
C/N0 Carrier to noise-density ratio, expressed in dB-Hz

© CTC advanced GmbH Page 21 of 22

Document Created: 2018-05-09 11:02:46
Document Modified: 2018-05-09 11:02:46

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC