Manual

FCC ID: IPH-A2670

Users Manual

Download: PDF

                                 Sport PRO™




                                Owner’s Manual




July 2015   Printed in Taiwan       190-01893-00_0A


All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the
right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such
changes or improvements. Go to www.garmin.com for current updates and supplemental information concerning the use of this product.
Garmin and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. Sport PRO™ is a trademark of
       ®



Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.
CAN ICES-3(B)/NMB-3(B)


                         Table of Contents
Getting Started............................................................... 1
Setting Up the Sport PRO System .............................................. 1
Device Overviews ....................................................................... 1
    Sport PRO Handheld Device ................................................. 1
    Sport PRO Dog Device .......................................................... 1
Attaching the Dog Collar Device to the Collar Strap ................... 1
Charging the Handheld Device ................................................... 1
Charging the Dog Collar Device ................................................. 1
Turning On the Dog Collar Device .............................................. 2
    Turning Off the Device ........................................................... 2
Dog Collar Device ....................................................................... 2
    Pairing a Dog Collar Device with the Handheld Device ......... 2
    Selecting a Dog Collar Device ............................................... 2
Fitting the Collar on Your Dog .................................................... 2
    Selecting and Installing the Contact Points ........................... 2
Dog Training................................................................... 3
Training Methods ........................................................................ 3
Choosing the Correct Intensity Level .......................................... 3
   Changing the Intensity Level ................................................. 3
BarkLimiter .................................................................................. 3
   Automatic Intensity ................................................................. 3
   Status LED ............................................................................. 3
   Enabling the BarkLimiter Feature from the Handheld
   Device .................................................................................... 3
   Enabling the Independent BarkLimiter Feature from the Dog
   Collar Device .......................................................................... 4
   Bark Odometer™ ................................................................... 4
Using the Light ............................................................................ 4
Device Information......................................................... 4
Handheld Device Specifications ................................................. 4
Dog Collar Device Specifications ................................................ 4
Sport PRO Battery Replacement Instructions ............................ 4
  Sport PRO Handheld Device Components ............................ 4
  Replacing the Handheld Device Battery ................................ 4
  Sport PRO Dog Collar Device Components .......................... 5
  Replacing the Dog Collar Device Battery ............................... 5
Registering Your Device ............................................................. 5
Getting More Information ............................................................ 5
Getting the Owner's Manual ....................................................... 5
Index................................................................................ 6




Table of Contents                                                                                  i




                      Getting Started                               Attaching the Dog Collar Device to the Collar
                            WARNING
                                                                    Strap
                                                                    1 With the buckle À facing outward, insert the end of the collar
See the Important Safety and Product Information guide in the
                                                                      strap through the slot Á on the collar device.
product box for product warnings and other important
information.

Setting Up the Sport PRO System
Before you can use the Sport PRO system, you must set up the
devices.
1 Attach the dog collar device to the collar strap (Attaching the
  Dog Collar Device to the Collar Strap, page 1).
2 Charge the handheld device (Charging the Handheld Device,
  page 1).
3 Charge the dog collar device (Charging the Dog Collar             2 Pull most of the collar strap through the two slots  on the
  Device, page 1).                                                    dog device.
4 Turn on the devices (Turning On the Dog Collar Device,            3 Insert the end of the collar strap through the slot à on the
  page 2).                                                            opposite side of the device.
5 If necessary, pair the dog collar device with the handheld        4 Pull the strap until it is tight across the front of the device.
  device (Pairing a Dog Collar Device with the Handheld
  Device, page 2).
                                                                    Charging the Handheld Device
Device Overviews                                                                                NOTICE
                                                                    To prevent corrosion, thoroughly dry the USB port, the weather
Sport PRO Handheld Device
                                                                    cap, and the surrounding area before charging or connecting to
                                                                    a computer.
                                                                    You should fully charge the battery before you use the device for
                                                                    the first time or whenever the battery is low. It is normal for the
                                                                    battery to discharge in approximately 7 to 10 weeks when the
                                                                    device is not in use. Charging a fully depleted battery takes
                                                                    about 2 hours.
                                                                    NOTE: The device will not charge when it is outside the
                                                                    temperature range of 0° to 40°C (32° to 104°F).
                                                                    1 Lift the weather cap À.




      Dog collar device toggle switch
                                                                    2 Plug the small end of the power cable into the mini-USB port
À
      Intensity level and operating mode dial
Á                                                                     Á on the device.
      Continuous stimulation key
Â
      BarkLimiter™ on key (AUX mode)
                                                                    3 Plug the other end of the power cable into a power source.
      Momentary stimulation key
                                                                      The status LED is solid red when the device is charging.
                                                                    4 After the status LED turns solid green, unplug the power
Ã
      BarkLimiter off key (AUX mode)
Ä     Vibration key                                                   cable from the device.
      Light on key (AUX mode)
Å     Tone key                                                      Charging the Dog Collar Device
      Light off key (AUX mode)
                                                                                                NOTICE
Sport PRO Dog Device                                                To prevent corrosion, thoroughly dry the USB port, the weather
                                                                    cap, and the surrounding area before charging or connecting to
                                                                    a computer.
                                                                    You should fully charge the battery before you use the device for
                                                                    the first time or whenever the battery is low. It is normal for the
                                                                    battery to discharge in approximately 7 to 10 weeks when the
                                                                    device is not in use. Charging a fully depleted battery takes
À        Power key                                                  about 2 hours.
Á        Status LED                                                 NOTE: The device will not charge when it is outside the
        Lights                                                     temperature range of 0° to 40°C (32° to 104°F).
à        Contact points                                             1 Snap the charging clip À onto the device Á.
Ä        Charging clip contacts


Getting Started                                                                                                                          1


                                                                        Move the dog collar device toggle switch to select the color
                                                                        associated with a dog collar device.
                                                                     The training keys control the dog collar device associated with
                                                                     the selected color.

                                                                     Fitting the Collar on Your Dog
                                                                                                      CAUTION
                                                                     To prevent irritation from the contact points, remove the collar
                                                                     for at least eight hours out of every 24-hour period.
                                                                     This device is not intended for human use. Do not attempt to
2 Plug the power cable into a power source.                          use on any person.
    The status LED is solid red when the collar is charging.         Do not spray the device or collar with harsh chemicals including
3 After the status LED turns solid green, remove the charging        but not limited to flea or tick spray. Always ensure that any flea
    clip from the collar.                                            or tick spray that is applied to the dog is completely dry before
                                                                     placing the collar on the dog. Small amounts of harsh chemicals
Turning On the Dog Collar Device                                     can damage the plastic components and collar laminate.
• To turn on the dog collar device in training mode, hold the        In order to effectively train the dog, the collar and device must fit
  power key until the status LED turns green and the collar          the dog properly. If the collar is too loose or positioned
  beeps.                                                             incorrectly, stimulation may be inconsistent. This can delay or
• To turn on the dog collar device in independent BarkLimiter        prevent successful training.
  mode, hold the power key until the status LED turns blue
                                                                     1 Position the device at the front of the dog's neck, with the
  (Enabling the Independent BarkLimiter Feature from the Dog            status LED facing toward the dog's chin and the contact
  Collar Device, page 4).                                               points against the throat.
• To turn on the dog collar device in pairing mode, hold the            TIP: For bark correction, the device contact points should be
  power key until the status LED turns yellow (Pairing a Dog            positioned near the dog's vocal cords. This location varies
  Collar Device with the Handheld Device, page 2).                      based on the breed of dog. If the device does not seem to
Turning Off the Device                                                  detect the dog's barks, you should move the device closer to
1 On the dog collar device, hold the power key until the status         or farther from the dog's body to find the ideal location.
    LED turns red.                                                   2 Tighten the strap so that it is very snug around the dog's
2 Release the power key.                                                neck, and fasten the buckle.
    The dog collar device beeps to confirm powering off.                NOTE: The collar should fit tightly and should not be able to
                                                                        rotate or slide on the dog's neck. The dog must be able to
    NOTE: If the device is powered off in BarkLimiter mode, the         swallow food and water normally. You should observe your
    LED flashes the number of corrected barks before powering           dog's behavior to verify that the collar is not too tight.
    off (Bark Odometer™, page 4).

Dog Collar Device
You can use up to 3 dog collar devices with a single handheld
device.
Each dog collar device must be paired with the handheld device
before it can be used. During the pairing process, each dog
collar device is associated with a different color on the handheld
device.
Pairing a Dog Collar Device with the Handheld Device
NOTE: If your handheld device and dog collar device were
included in the same package, the devices are paired from the
factory.
1 On the handheld device, move the toggle switch to choose
   the color associated with the dog collar device.
2 On the handheld device, set the intensity level to a numbered
   position.
                                                                     3 Wiggle the device to work the contact points through the
3 On the dog collar device, hold the power key for about 5             dog's coat.
   seconds until the status LED turns yellow.
                                                                       NOTE: The contact points must have contact with the dog's
4 While the dog collar device status LED is yellow, select a           skin to be effective.
   training key on the handheld device.
                                                                     4 If the strap is too long, cut off the excess, leaving at least
The dog collar device beeps when the devices have paired               8 cm (3 in.) to spare.
successfully.
                                                                       TIP: You can mark the hole used to fasten the buckle for
TIP: If the devices did not pair successfully, you should verify       future reference.
the batteries in both devices are fully charged and the intensity
level is set to a numbered position.                                 Selecting and Installing the Contact Points
                                                                     For best results, select the correct contact points based on your
Selecting a Dog Collar Device                                        dog's coat.
Before you can select and control a dog collar device, you must
pair the dog collar device with the handheld device (Pairing a
Dog Collar Device with the Handheld Device, page 2).

2                                                                                                                           Getting Started


1 Select the correct contact point length for your dog's coat             BarkLimiter
   type:
   • For dogs with thicker coats, use the longer contact points.                                         NOTICE
                                                                          Before playing with your dog, you should remove the dog collar
   • For dogs with shorter coats, use the shorter contact
                                                                          device or deactivate the BarkLimiter feature.
      points.
                                                                          When using the BarkLimiter feature, you should remove all other
2 If necessary, use the included wrench to remove the contact
                                                                          collars, tags, or other items from your dog. These other items
   points.
                                                                          can cause the BarkLimiter feature to activate when the dog is
3  Twist the contact points into the collar.                              not barking.
4 Tighten with the included wrench, but do not overtighten.
                                                                          The BarkLimiter feature can correct your dog automatically
When you put the collar on the dog, make sure the contact                 when the dog barks. The device detects vibrations to distinguish
points are tight against the neck.                                        between barking and other vocalizations. You can use these
                                                                          methods when correcting your dog with the BarkLimiter feature.
                       Dog Training                                       • Vibration instead of stimulation
                                                                          • Fixed stimulation
You should research and investigate the training methods best
suited for you, your dog, and your needs.                                 • An automatic, gradual increase in stimulation intensity
When used properly, the Sport PRO training system is an                   Automatic Intensity
effective training tool to aid your dog in reaching its full potential.   The device can set the stimulation intensity level automatically
The use of the training system should be part of an overall               based on the barking behavior of the dog. The device starts at
training program.                                                         the lowest intensity level and increases the intensity level
                                                                          gradually until the dog stops barking. When the dog is quiet, the
Training Methods                                                          intensity decreases over time.
Momentary stimulation: Applies a brief stimulation when you               The automatic intensity feature is designed to eliminate
   press the training key, regardless of how long the key is              excessive nuisance barking. To stop barks more immediately,
   depressed.                                                             you should set the intensity level manually.
Continuous stimulation: Applies stimulation to the dog the
   entire time you press the training key, for a maximum of 8
                                                                          Status LED
   seconds. Your stimulations should typically be much shorter            The status LED flashes briefly when the dog collar device
   than 8 seconds.                                                        detects motion or corrects a bark.
                                                                          Green, yellow, or red   Motion was detected, and no correction was
Tone: Activates an audible tone instead of stimulation. A tone            flash                   applied.
   can be used as either a positive or negative training cue,
                                                                          Blue flash              A bark was detected, and a correction was
   depending on your training program.
                                                                                                  applied.
Vibration: Applies vibration instead of stimulation to the dog the
                                                                          NOTE: A green, yellow, or red flash denotes how much charge
   entire time you press the training key, for a maximum of 8
                                                                          is left in the dog device battery, ranging from high to low.
   seconds. The effectiveness of vibration may vary based on
   the dog's temperament and experience.                                  Enabling the BarkLimiter Feature from the Handheld
                                                                          Device
Choosing the Correct Intensity Level                                      You can use your handheld device to enable BarkLimiter
1 Set the intensity to the lowest level.                                  features. When you enable BarkLimiter mode from the handheld
2 Select a training key.                                                  device, you can set the dog collar device to use auto-rise,
                                                                          vibration, or fixed stimulation levels.
3 Observe the dog for a reaction, such as a head shake, neck
    movement, or just a change in expression.                             1 Set the operating mode dial to AUX.
    Sometimes dogs will vocalize due to the surprise of the               2 Select BARKLIMITER ON.
    electrical stimulation. If the dog vocalizes more than once,             The green LED flashes.
    the intensity level is too high for beginning training.               3 While the green LED is flashing, select an option:
4 If there is no reaction, increase the intensity level by one level         • To set vibration, select VIBE.
    until the dog has a slight but recognizable reaction to the
                                                                             • To set a fixed stimulation level, set the dial to a stimulation
    stimulation.
                                                                                 level and select CONTINUOUS.
The intensity level that causes a slight but recognizable reaction
                                                                             • To set auto-rise, select BARKLIMITER ON.
is your dog's baseline level for beginning collar training. You do
not need to, and should not, apply this intensity selection test          A blue LED on the dog collar device indicates that it is in
again.                                                                    BarkLimiter mode.
After you begin training, the dog’s performance guides your               Turning Off the BarkLimiter Feature from the Handheld
intensity selection. As the dog advances in training, you may             Device
need to change the level depending upon the training situation.           NOTE: If you enabled the BarkLimiter feature from the dog
Changing the Intensity Level                                              device, you cannot turn it off from the handheld device.
You can select a different intensity level for each dog collar            1 Set the dial to AUX.
device.                                                                   2 Select BARKLIMITER OFF.
1 Select a dog collar device (Selecting a Dog Collar Device,              Overriding the BarkLimiter Feature
  page 2).
                                                                          NOTE: If you enabled the BarkLimiter feature from the dog
2 Adjust the dial to increase or decrease the intensity level.            collar device, you cannot override it using the handheld device.
                                                                          If you need to apply a quick stimulation when your dog collar
                                                                          device is in BarkLimiter mode, you can override the BarkLimiter
                                                                          feature using the handheld device. You can return to BarkLimiter

Dog Training                                                                                                                                   3


mode by enabling it from the handheld device (Enabling the              Storage temperature range (up   From -20° to 50°C (from -4° to 122°F)
BarkLimiter Feature from the Handheld Device, page 3).                  to 1 mo.)
  Hold CONTINUOUS, TONE, or VIBE for 4 seconds.                         Storage temperature range (up   From -20° to 35°C (from -4° to 95°F)
                                                                        to 3 mo.)
  The dog collar device returns to training mode.
                                                                        Water rating                    1 ATM*
Enabling the Independent BarkLimiter Feature from
the Dog Collar Device                                                   *The device withstands pressure equivalent to a depth of 10 m.
                                                                        For more information, go to www.garmin.com/waterrating.
The dog collar device can operate independently as a bark
correction device. You can enable the BarkLimiter feature in
auto-rise mode directly from the dog collar device. This provides       Sport PRO Battery Replacement Instructions
longer battery life than enabling the BarkLimiter feature from the
handheld device.                                                                                       WARNING
                                                                        This product contains a lithium-ion battery. To prevent the
NOTE: When using the device in this mode, the radio signal is           possibility of personal injury or product damage caused by
disabled and you cannot control the dog collar device with the          battery exposure to extreme heat, store the device out of direct
handheld device.                                                        sunlight.
1 On the dog collar device, hold the power key until the LED            Do not use a sharp object to remove batteries.
   flashes blue.
2 To return to training mode, turn off the dog collar device and                                     CAUTION
   turn it back on in training mode (Turning On the Dog Collar          Contact your local waste disposal department to properly
   Device, page 2).                                                     recycle the batteries.
Bark Odometer™                                                          Sport PRO Handheld Device Components
When you turn off the dog collar device in independent
BarkLimiter mode, the LED flashes red and green to report the
number of times the device detected a bark since it was last
turned on. This can help you track your dog's barking behavior.
Red flash                              10 barks
Green flash                            1 bark

For example, one red flash followed by four green flashes
indicates the device detected 14 barks.
Zero flashes indicates the device detected zero barks.

Using the Light
You can use the light feature on your device to verify pairing,
help locate your dog, and provide safety for your dog at night.
1 Select a dog collar device (Selecting a Dog Collar Device,
   page 2).
2 Set the dial to AUX.
                                                                                   Security screws
3 Select to turn the light on.
                                                                        À
                                                                                   Back plate
4 Select to turn the light off.
                                                                        Á
                                                                        Â          Battery
                                                                                   Battery connector
                 Device Information
                                                                        Ã
                                                                        Ä          Front plate
                                                                                   Gasket
Handheld Device Specifications
                                                                        Å
                                                                        Replacing the Handheld Device Battery
Battery type                    Rechargeable lithium-ion                Before you can replace the battery, you must remove all dirt,
Battery life                    Up to 60 hr. of typical use             water, and debris from the device. You also need the security
Operating temperature range     From -20° to 60°C (from -4° to 140°F)   screwdriver included in the battery replacement kit.
Charging temperature range      From 0° to 40°C (from 32° to 104°F)     1 Remove the security screws from the back of the device.
Storage temperature range (up   From -20° to 50°C (from -4° to 122°F)   2 Lift up the back plate.
to 1 mo.)
                                                                        3 Grip the battery connector wires close to the connector, and
Storage temperature range (up   From -20° to 35°C (from -4° to 95°F)       pull the connector perpendicular to the circuit board to
to 3 mo.)                                                                  disconnect the battery connector from the device.
Water rating                    IEC 60529 IPX7*
                                                                        4 Remove the old battery from the back plate, noting the
*The device withstands incidental exposure to water of up to 1 m           orientation of the battery.
for up to 30 min. For more information, go to www.garmin.com               The battery fits tightly. It may be necessary to pry the battery
/waterrating.                                                              out of the back plate using a non-sharp, non-metal object.
                                                                        5 Install the new battery into the back plate with the label side
Dog Collar Device Specifications                                           up, using the same orientation as the old battery.
Battery type                    Rechargeable, replaceable lithium-ion   6 With the new battery, connect the battery connector to the
Battery life                    Up to 60 hr. of typical use
                                                                           device.
Operating temperature range     From -20° to 60°C (from -4° to 140°F)      When properly installed, the connector plug snaps into the
                                                                           port.
Charging temperature range      From 0° to 40°C (from 32° to 104°F)

4                                                                                                                          Device Information


7 Verify the gasket is not damaged and is completely seated in
   the groove on the front half of the device.
8 Verify the USB gasket is not damaged and is completely
   positioned around the USB opening on the back half of the
   device.
9 While ensuring the battery wires are not pinched, hold the
   back plate and the device firmly together, and replace all
   security screws without tightening them.
10 Verify the back plate and the device are aligned with no gaps.
11 Tighten the screws evenly.
12 Verify the gasket is not sticking out of the device.
Sport PRO Dog Collar Device Components


                                                                      7 Verify the gasket is not damaged and is completely seated in
                                                                         the groove.
                                                                      8 With the new battery, connect the battery connector to the
                                                                         device.
                                                                         When properly installed, the connector plug snaps into the
                                                                         port.
                                                                      9 Replace the front plate, and replace and tighten the six
                                                                         screws to secure the front plate.
                                                                      10 Verify the gasket is not sticking out of the device.

                                                                      Registering Your Device
                                                                      Help us better support you by completing our online registration
                                                                      today.
                                                                      • Go to http://my.garmin.com.
                                                                      • Keep the original sales receipt, or a photocopy, in a safe
                                                                         place.

                                                                      Getting More Information
                                                                      You can find more information about this product on the Garmin     ®



                                                                      website.
                                                                      • Go to www.garmin.com/outdoor.
          Security screws
                                                                      • Go to http://buy.garmin.com, or contact your Garmin dealer
À
          Top plate
Á                                                                       for information about optional accessories and replacement
         Battery plate screws                                          parts.
à        Battery plate
Ä         Battery                                                     Getting the Owner's Manual
Å         Gasket                                                      You can get the most recent owner's manual from the web.
Æ         Front enclosure                                             1 Go to www.garmin.com/manuals/sportpro.
Replacing the Dog Collar Device Battery                               2 View or download the full owner's manual in your preferred
                                                                        format.
Before you can replace the battery, you must remove all dirt,
water, and debris from the device. You also need a small
Phillips screwdriver and the security screwdriver included in the
battery replacement kit.
1 Remove the six screws from the top plate, and remove the
   top plate.
2 Remove the two screws from the battery plate, and remove
   the battery plate.
3 Grip the battery connector wires close to the connector, and
   pull the connector parallel to the circuit board to disconnect
   the battery connector from the device.
4 Remove the battery.
   The battery fits tightly. It may be necessary to pry the battery
   out of the back plate using a non-sharp, non-metal object.
5 Install the new battery into the front enclosure with the label
   side of the battery facing up, and the leading edge of the
   battery placed under the charging contact ledge of the
   device.
6 Replace the battery plate, and replace and tighten the two
   screws.

Device Information                                                                                                                       5


                    Index
A
accessories 5
B
bark correction 3, 4
bark odometer 4
battery
   charging 1
   replacing 4, 5
C
charging
    collar 1
    handheld 1
collar
    attaching strap 1
    charging 1
    contact points 1, 2
    fitting 2
    light 4
    pairing 2
contact points 1, 2
D
device, registration 5
dog
   status 3
   training 2
   training basics 3
   training intensity levels 3
dog collar device 1, 2
I
intensity level
    automatic 3
    changing 3
    choosing 3
K
keys 1
P
pairing, collar 2
power key 1, 2
product registration 5
R
registering the device 5
replacing the battery 4
S
specifications 4
T
training
    stimulation 3
    tone 3
    vibration 3
troubleshooting 5




6                                Index




www.garmin.com/support
  +43 (0) 820 220230       + 32 2 672 52 54



  0800 770 4960            1-866-429-9296



  +385 1 5508 272          +420 221 985466
  +385 1 5508 271          +420 221 985465



  + 45 4810 5050           + 358 9 6937 9758



  + 331 55 69 33 99        + 39 02 36 699699



  (+52) 001-855-792-7671   0800 0233937



                           00800 4412 454
  +47 815 69 555
                           +44 2380 662 915



  (+35) 1214 447 460       +386 4 27 92 500



  0861 GARMIN (427 646)
                           +34 93 275 44 97
  +27 (0)11 251 9999



  + 46 7744 52020          +886 2 2642-9199 ext 2



  0808 238 0000            +49 (0) 89 858364880
  +44 (0) 870 8501242      zum Ortstarif - Mobilfunk
                           kann abweichen

  913-397-8200
  1-800-800-1020




                                                       © 2015 Garmin Ltd. or its subsidiaries



Document Created: 2019-07-14 22:12:46
Document Modified: 2019-07-14 22:12:46

© 2019 FCC.report
This site is not affiliated with or endorsed by the FCC