User Manual Instructions

FCC ID: IPH-03473

Users Manual

Download: PDF
FCCID_4310509

Installation Procedures Connecting to Power FORCE™ TROLLING MOTOR You can power the foot pedal by connecting it to the boat FOOT PEDAL battery. If you prefer a completely wireless installation, you can power the foot pedal using AA batteries. INSTALLATION NOTICE If you connect the foot pedal to the boat battery, you should not INSTRUCTIONS install AA batteries. Batteries left in the foot pedal for long periods may corrode and cause damage. Getting Started 1 Route the included power cable to the boat battery or circuit breaker, and to the location where you plan to mount or use WARNING the foot pedal. Do not run the motor when the propeller is out of the water. If needed, you can extend the power cable using 18 AWG Contact with the rotating propeller may result in severe injury. (0.82 mm2) wire. Do not use the motor in areas where you or other people in the NOTE: If you extend the power cable, you must first remove water may come into contact with the rotating propeller. the fuse and a re-install it between the boat battery or circuit Always disconnect the motor from the battery before cleaning or breaker and the cable extension. servicing the propeller to avoid injury. 2 Connect the red wire to the positive terminal of the battery or CAUTION breaker, and connect the black wire to the negative terminal. When stowing or deploying the motor, be aware of the risk of 3 Push the connector on the power cable onto the port on the entrapment or pinching from moving parts, which can result in bottom of the foot pedal, and turn the locking ring clockwise injury. to secure it. When stowing or deploying the motor, be aware of slick surfaces 4 Route the power cable through the channel on the bottom of the foot pedal. may result in injury. Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding. NOTICE FT around the motor. Slipping when stowing or deploying the motor When drilling or cutting, always check what is on the opposite side of the surface. A To avoid damage to your boat, this device should be installed by a qualified marine installer. Specific knowledge of marine electrical systems is required for proper installation. Tools Needed R • Two AA alkaline, NiMH, or lithium batteries (if powering with batteries) Installing Batteries • Four 5 mm (#10) stainless steel self-tapping screws (to The foot pedal can operate using two AA alkaline, NiMH, or secure the pedal to the boat deck) lithium batteries (not included). Use lithium batteries for best D • A drill and a 3 mm (1/8 in.) drill bit (to secure the pedal to the results. boat deck) 1 Lift up the front of the foot pedal as far as possible. • Marine sealant (to seal the screws when securing the pedal 2 Pinch the sides of the battery cover , and pull up to remove to the boat deck) it. Mounting and Power Considerations When selecting a location for the foot pedal, observe these considerations. • The foot pedal communicates wirelessly with the trolling motor, so you do not need to connect it to the motor using a cable. • You can power the foot pedal by connecting it to a power source using the provided cable, or by using two AA batteries. • If you prefer, you can mount the foot pedal to the boat deck. Mounting hardware is not provided. 3 Insert two AA batteries, observing polarity. • If your boat has a built-in or aftermarket foot pedal well, you can install the pedal in the well. Installation hardware is not 4 Place the battery cover over the batteries, and push down provided. until both sides snap into place. Mounting the Foot Pedal on the Boat Deck NOTICE You are not required to mount the foot pedal to the deck, but it is highly recommended, especially if you are powering it using May 2019 RC

batteries. An unsecured foot pedal may slide on the deck and Fabricating a Permanent Shim fall off of the boat. If you are installing the foot pedal in a tray and you would like to raise the height, you should fabricate a permanent shim to install 1 Determine the appropriate mounting hardware for your boat under the pedal. deck. 1 Purchase a suitable shim material, such as marine grade You should use 5 mm (#10) stainless steel self-tapping PVC, of the appropriate thickness for your installation. screws whose length is determined by the material of your boat deck. 2 Trace the shape of the tray on the shim material or a piece of paper. 2 Place the included mounting template in the selected location. 3 Cut the shim from the material. 3 Using a 3 mm (1/8 in.) bit, drill the pilot holes indicated on the 4 Place the shim into the tray to check the fit, and trim the template, and remove the template. edges as needed. 4 Select an action: 5 Locate the drain hole in the tray, mark the location of the hole on the shim, and drill a hole through the shim to allow water • If you are powering the foot pedal using batteries, check to drain properly. the weather cap on the power connector on the bottom of the foot pedal to make sure it is secured. Adjusting the Tension • If you are powering the foot pedal using the included You can adjust the tension on the foot pedal if it moves too cable, connect the cable to the bottom of the foot pedal if easily or not easily enough. you have not done so already. 1 Locate the tension adjustment screw on the left side of the 5 Apply marine sealant to the pilot holes to prevent water from foot pedal. entering the boat deck (optional). 6 Secure the foot pedal to your boat deck using the mounting hardware. Mounting the Foot Pedal in a Foot Pedal Tray Before you can mount the foot pedal in a tray, you must install the tray in the deck of your boat following the instructions provided with the tray. material. NOTE: You should use 5 mm (#10) stainless steel self-tapping FT If you plan to secure the foot pedal inside the tray, you must purchase the appropriate mounting hardware for the tray screws that are long enough to pass through any shim used and 2 Select an action: • Turn the screw clockwise to increase the tension. • Turn the screw counterclockwise to decrease the tension. A through the tray material. 3 Test the foot pedal, and repeat the previous step until the foot 1 Place the foot pedal into the tray and test the height of the pedal moves like you want it to. pedal. 2 If necessary, place temporary shims under the pedal until it is Specifications R at the height you want. Dimensions (L×W×H) 303 × 221 × 110 mm (1115/16 × 811/16 × After you determine the height, you should fabricate a 4 5/16 in. permanent shim to install in the tray with the foot pedalFabricating a Permanent Shim, page 2. Weight 1.8 kg (4 lb) Operating temperature From -15 to 70°C (From 5 to 158°F) 3 Select an action: D Water rating IEC 60529 IPX71 • If you are powering the foot pedal using the included cable, connect the cable to the bottom of the foot pedal if Material Plastic you have not done so already. Input voltage From 10 to 45 Vdc • If you are powering the foot pedal using batteries, check Typical input current < 1 mA @ 12 Vdc the weather cap on the power connector on the bottom of Max input current 10 mA @ 12 Vdc the foot pedal to make sure it is secured. Fuse (on the power cable) 2 A mini-blade type 4 If you are using a shim to raise the height of the pedal, Power cable length 2 m (6.6 ft.) secure the shim to the bottom of the foot pedal (optional). Battery type Two AA batteries (Alkaline, NiMH, or 5 If you do not plan to secure the foot pedal to the bottom of lithium. Not included.) the tray, place the pedal into the tray to complete the Battery life At least 1 year installation. Radio frequency 2.4 GHz @ 2.5 dBm nominal 6 If you plan to secure the foot pedal to the bottom of the tray, Compass-safe distance 60 cm (2 ft.) trim and place the included mounting template in the tray. 7 Using an appropriate drill bit for the tray material and the © 2019 Garmin Ltd. or its subsidiaries mounting hardware, drill the pilot holes indicated on the Garmin , the Garmin logo, and GPSMAP are trademarks of Garmin Ltd. or its ® ® template, and remove the template. subsidiaries, registered in the USA and other countries. ActiveCaptain , ECHOMAP™, ® 8 Apply marine sealant to the pilot holes to prevent water from and Force™ are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not entering the boat deck. be used without the express permission of Garmin. 9 Secure the foot pedal (and shim, if necessary) to the tray using the mounting hardware. support.garmin.com

FT A R D 1 *The device withstands incidental exposure to water of up to 1 m for up to 30 min. For more information, go to www.garmin.com/waterrating. 3

FT A R D support.garmin.com


Document Created: 2019-05-30 11:52:12
Document Modified: 2019-05-30 11:52:12
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC