Test Report

FCC ID: INGRU-G3TB

Test Report

Download: PDF
FCCID_4032712

FCC Part 74 Subpart H EMI TEST REPORT of E.U.T. : Handheld Transmitter FCC ID. : INGRU-G3TB Model No. : RU-G3TB Working Frequency : 470~608 MHz for APPLICANT : JTS Professional Co., Ltd. ADDRESS : NO. 148, 9TH INDUSTRY RD., TA-LI INDUSTRIAL PARK,TAI-LI CITY, TAIWAN, R.O.C. Test Performed by ELECTRONICS TESTING CENTER (ETC) , TAIWAN NO. 34. LIN 5, DINGFU VIL., LINKOU DIST., NEW TAIPEI CITY, TAIWAN, 24442, R.O.C. TEL : (02)26023052 FAX : (02)26010910 http:// www.etc.org.tw ; e-mail:emc@etc.org.tw Report Number : 17-07-RBF-021 Rev. 2.0

RUETC Report No.: 17-07-RBF-021 FCC ID: INGRU-G3TB TEST REPORT CERTIFICATION Applicant : JTS Professional Co., Ltd. NO. 148, 9TH INDUSTRY RD., TA-LI INDUSTRIAL PARK, TAI-LI CITY, TAIWAN, R.O.C. Manufacturer : JTS Professional Co., Ltd. NO. 148, 9TH INDUSTRY RD., TA-LI INDUSTRIAL PARK, TAI-LI CITY, TAIWAN, R.O.C. Description of EUT : a) Type of EUT : Handheld Transmitter b) Trade Name : JTS c) Model No. : RU-G3TB d) FCC ID : INGRU-G3TB e) Working Frequency : 470~608 MHz f) Power Supply : DC 3V Battery Regulation Applied : FCC Rules and Regulations Part 74 Subpart H I HEREBY CERTIFY THAT; The data shown in this report were made in accordance with the procedures given in ANSI C63.10-2013 and the energy emitted by the device was founded to be within the limits applicable. I assume full responsibility for accuracy and completeness of these data. Issued Date : Sep. 25, 2018 Test Engineer : (Brian Huang, Engineer ) Approve & Authorized Signer : S. S. Liou, Section Manager EMC Dept. II of ELECTRONICS TESTING CENTER, TAIWAN Rev. 2.0

RUETC Report No.: 17-07-RBF-021 FCC ID: INGRU-G3TB Table of Contents Page 1. GENERAL INFORMATION ............................................................................................................................... 1 1.1 PRODUCT DESCRIPTION........................................................................................................................................... 1 1.2 TEST METHODOLOGY.............................................................................................................................................. 1 1.3 TEST FACILITY ........................................................................................................................................................ 1 2. REQUIREMENTS OF PROVISIONS................................................................................................................. 2 2.1 DEFINITION ............................................................................................................................................................. 2 2.2 FREQUENCIES AVAILABLE ...................................................................................................................................... 2 2.3 REQUIREMENTS FOR RADIO EQUIPMENT ON CERTIFICATION .................................................................................. 2 2.4 LABELING REQUIREMENT ....................................................................................................................................... 3 3. OUTPUT POWER MEASUREMENT ................................................................................................................ 4 3.1 PROVISION APPLICABLE .......................................................................................................................................... 4 3.2 MEASUREMENT PROCEDURE ................................................................................................................................... 4 3.3 TEST DATA.............................................................................................................................................................. 4 3.4 TEST EQUIPMENT .................................................................................................................................................... 5 4. MODULATION CHARACTERISTICS .............................................................................................................. 6 4.1 PROVISIONS APPLICABLE ........................................................................................................................................ 6 4.2 MEASUREMENT METHOD ........................................................................................................................................ 6 4.3 MEASUREMENT INSTRUMENT ................................................................................................................................. 7 4.4 MEASUREMENT RESULT .......................................................................................................................................... 7 5. OCCUPIED BANDWIDTH OF EMISSION....................................................................................................... 9 5.1 PROVISIONS APPLICABLE ........................................................................................................................................ 9 5.2 MEASUREMENT METHOD ........................................................................................................................................ 9 5.3 OCCUPIED BANDWIDTH TEST EQUIPMENT .............................................................................................................. 9 5.4 BANDWIDTH MEASURED ....................................................................................................................................... 10 6. FIELD STRENGTH OF EMISSION ................................................................................................................. 14 6.1 PROVISIONS APPLICABLE ...................................................................................................................................... 14 6.2 MEASUREMENT PROCEDURE ................................................................................................................................. 14 6.3 MEASURING INSTRUMENT ..................................................................................................................................... 16 6.4 MEASURING DATA ................................................................................................................................................ 17 6.5 RADIATED MEASUREMENT PHOTOS ...................................................................................................................... 25 7. FREQUENCY STABILITY MEASUREMENT ............................................................................................... 27 7.1 PROVISIONS APPLICABLE ...................................................................................................................................... 27 7.2 MEASUREMENT PROCEDURE ................................................................................................................................. 27 7.3 MEASUREMENT INSTRUMENT ............................................................................................................................... 28 7.4 MEASUREMENT DATA ........................................................................................................................................... 29 8 CONDUCTED EMISSION MEASUREMENT ................................................................................................. 30 8.1 STANDARD APPLICABLE........................................................................................................................................ 30 Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 1 of 30 Sheets FCC ID: INRU-G3TB 1. GENERAL INFORMATION 1.1 Product Description a) Type of EUT : Handheld Transmitter b) Trade Name : JTS c) Model No. : RU-G3TB d) FCC ID : INGRU-G3TB e) Working Frequency : 470~608 MHz f) Power Supply : DC 3V Battery 1.2 Test Methodology Both conducted and radiated testing were performed according to the procedures in ANSI C63.10-2013. Test also follow “TIA-603-D(2010)-Land Mobile FM or PM Communications Equipment Measurement and Performance Standsrds” and section 2.1046, 2.1047, 2.1049, 2.1051, 2.1053, and 2.1055 of Part 2 of CFR 47. Measueement Software Software Version Note e3 Version 6.100618b Radiated Emission Test e3 Version 6.100421 Conducted Emission Test 1.3 Test Facility The open area test site and conducted measurement facility used to collect the radiated data is located on the roof top of Building at No.34, Lin 5, Dingfu Vil., Linkou Dist., New Taipei City, Taiwan 24442, R.O.C. This site is FCC 2.948 listed and accepted in a letter dated Jan. 29, 2014. Registration Number: 90589 Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 2 of 30 Sheets FCC ID: INRU-G3TB 2. REQUIREMENTS OF PROVISIONS 2.1 Definition Intentional radiator: A device that intentionally generates and emits radio frequency energy by radiation or induction. 2.2 Frequencies Available According to sec. 74.802 of Part 74, the following frequencies are available for low power auxiliary station : Frequencies (MHz) 26.100-26.480 455.000-456.000 54.000-72.000 470.000-488.000 76.000-88.000 488.000-494.000 161.625-161.775 494.000-608.000 174.000-216.000 614.000-806.000 450.000-451.000 944.000-952.000 2.3 Requirements for Radio Equipment on Certification (1) RF Output Power For transmitters, the power output shall be measured at the RF output terminals. (2) Modulation Characteristics For Voice Modulated Communication Equipment, a curve or equivalent data showing the frequency response of the audio modulating circuit over a range of 100 to 5000 Hz shall be submitted. (3) Occupied Bandwidth For radiotelephone transmitter, other than single sideband or indenpent sideband transmitter, when modulateed by a 2.5kHz tone at an input level 16 dB greater than that necessary to produce 50 percent modulation. (4) Spurious Emissions at Antenna Terminals The radio frequency voltage or power generated within the equipment and appearing on a spurious frequency shall be checked at the equipment output terminal when properly loaded with a suitable artificial antenna. Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 3 of 30 Sheets FCC ID: INRU-G3TB (5) Field Strength of Spurious Emissions Measurements shall be made to detect spurious emission that may be radiated directly from the cabinet, control circuits, power leads, or intermediate circuit elements under normal condition of installation and operation. (6) Frequencies Tolerance a) The frequency stability shall be measured with variation of ambient temperature. b) The frequency stability shall be measured with variation of primary supply voltage. 2.4 Labeling Requirement Each equipment for which a type acceptance application is filed on or after May 1,1981, shall bear an identification plate or label pursuant to §2.925（Identification of equipment） and §2.926（FCC identifier）. Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 4 of 30 Sheets FCC ID: INRU-G3TB 3. OUTPUT POWER MEASUREMENT 3.1 Provision Applicable According to §74.861(e)(1)(ii), the output power shall not exceed 250 milliwatts. 3.2 Measurement Procedure 1. Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. 2. Position the EUT as shown in figure 1, and Install new batteries in the EUT. Turn on the EUT ant set it to any one convenient frequency within its operating range. 3. Apply a 2.5 kHz modulation signal to EUT. Record the readings on the instrument. 4. Repeat above procedures until all frequencies measured were complete. Figure 1: Transmit power measurement configuration. Radio EUT Communication Test Set Power Meter 3.3 Test Data Operated mode : TX Test Date : Aug. 27, 2018 Temperature : 23°C Humidity : 68 % Frequency Transmit Power Limit (MHz) (dBm) (mW) (mW) 520.050 5.20 3.311 250.0 607.925 9.10 8.128 250.0 Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 5 of 30 Sheets FCC ID: INRU-G3TB 3.4 Test Equipment Equipment Manufacturer Model No. Calibration Date Next Cal. Date POWER METER ML2487A 2018/05/23 2019/05/22 ANRITSU +SENSOR +MA2491A Communications AEROFLEX 2945B 2018/01/10 2019/01/09 Service Monitor Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 6 of 30 Sheets FCC ID: INRU-G3TB 4. MODULATION CHARACTERISTICS 4.1 Provisions Applicable According to § 2.1047 (a), for Voice Modulated Communication Equipment, the frequency response of the audio modulating circuit over a range of 100 to 5000 Hz shall be measured. 4.2 Measurement Method A) Modulation Limit 1. Position the EUT as shown in figure 2, adjust the audio input frequency to 100 Hz and the input level from 0V to maximum permitted input voltage with recording each carrier frequency deviation responding to respective input level. 2. Repeat step 1 with changing the input frequency for 200, 500, 1000, 3000, and 5000 Hz in sequence. B) Frequency response of all circuits 1. Position the EUT as shown in figure 2. 2. Vary the modulating frequency from 100 Hz to 15000 Hz with constant input voltage (derived from 5.4(a) of this test report), and observe the change in output. Figure 2 : Modulation characteristic measurement configuration Radio EUT Communication Test Set Spectrum Analyzer Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 7 of 30 Sheets FCC ID: INRU-G3TB 4.3 Measurement Instrument Equipment Manufacturer Model No. Calibration Date Next Cal. Date Communications AEROFLEX 2945B 2018/01/10 2019/01/09 Service Monitor Spectrum Analyzer Rohde & Schwarz FSP40 2017/11/02 2018/11/01 4.4 Measurement Result RF Frequency : 470MHz Test Date : Aug. 27, 2018 Temperature : 26 °C Humidity : 68 % A). Frequency response 100 Hz 200 Hz 500 Hz 1kHz 3 kHz 5 kHz 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 Output Level (V) 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 109 87 65 43 21 0 1 5 10 20 30 40 50 60 70 80 90 100 150 200 250 300 350 400 450 500 800 1000 Input Level (mV) Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 8 of 30 Sheets FCC ID: INRU-G3TB B). Modulation Limit 100 Hz 200 Hz 500 Hz 1kHz 3 kHz 5 kHz kHz 75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 0 1 5 10 20 30 40 50 60 70 80 90 100 150 200 250 300 350 400 450 500 800 1000 Input Level (mV) C). Frequency response of all circuits 20 10 Frequency Response (dB) 0 -10 -20 -30 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Input Frequency (kHz) Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 9 of 30 Sheets FCC ID: INRU-G3TB 5. OCCUPIED BANDWIDTH OF EMISSION 5.1 Provisions Applicable According to §2.1049 (c)(1), For radiotelephone transmitter, other than single sideband or indenpent sideband transmitter, when modulateed by a 2.5kHz tone at an input level 16 dB greater than that necessary to produce 50 percent modulation. According to §74.861( e)(5), the frequency emission bandwidth shall not exceed 200 kHz. 5.2 Measurement Method 1. Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. 2. Position the EUT as shown in figure 3, and Install new batteries in the EUT. Turn on the EUT ant set it to any one convenient frequency within its operating range. Set a reference level on the measuring instrument equal to the highest peak value. 3. Apply a 2.5 kHz modulation signal to EUT and measure the frequencies of the modulated signal from the EUT where it is the specified number of dB below the reference level set in step 2. This is the occupied bandwidth specified. Figure 3 : Occupied bandwidth measurement configuration Radio EUT Communication Test Set Spectrum Analyzer 5.3 Occupied Bandwidth Test Equipment Equipment Manufacturer Model No. Calibration Date Next Cal. Date Communications AEROFLEX 2945B 2018/01/10 2019/01/09 Service Monitor Spectrum Analyzer Rohde & Schwarz FSP40 2017/11/02 2018/11/01 Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 10 of 30 Sheets FCC ID: INRU-G3TB 5.4 Bandwidth Measured 5.4.1 Input Level Derived RF Frequency : 470MHz Test Date : Aug. 27, 2018 Temperature : 26 °C Humidity : 68 % Input Audio Frequency : 2.5 kHz, Sine Wave Frequency Devition kHz 70 60 50 40 30 20 10 0 Input Level (mV) The Level input to produce 50﹪modulation is 50 mV, therefore the magnitude 16 dB greater than it is 315 mV. Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 11 of 30 Sheets FCC ID: INRU-G3TB 5.4.2 Occupied Bandwidth Plotted Test Date : Aug. 25, 2018 Temperature : 23 °C Humidity : 68 % RF Frequency (MHz) 26 dB Bandwidth (kHz) 470.000 120.0 607.875 127.0 Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 12 of 30 Sheets FCC ID: INRU-G3TB * RBW 3 kHz Marker 1 [T1 ] VBW 10 kHz 3.17 dBm Ref 20 dBm Att 50 dB SWT 30 ms 469.956000000 MHz 20 ndB [T1] 26.00 dB BW 120.000000000 kHz Temp 1 [T1 ndB] A 10 1 -22.21 dBm 1 PK 469.941000000 MHz VIEW 0 Temp 2 [T1 ndB] -23.87 dBm 470.061000000 MHz -10 -20 T1 T2 -30 -40 -50 -60 -70 -80 Center 470 MHz 25 kHz/ Span 250 kHz 470-腰掛 Date: 18.SEP.2017 15:06:59 Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 13 of 30 Sheets FCC ID: INRU-G3TB * RBW 3 kHz Marker 1 [T1 ] VBW 10 kHz 4.27 dBm Ref 20 dBm Att 50 dB * SWT 225 ms 607.954500000 MHz 20 ndB [T1] 26.00 dB BW 120.500000000 kHz Temp 1 [T1 ndB] A 10 1 -21.40 dBm 1 PK 607.940000000 MHz VIEW 0 Temp 2 [T1 ndB] -21.00 dBm 608.060500000 MHz -10 T1 T2 -20 -30 -40 -50 -60 -70 -80 Center 608 MHz 25 kHz/ Span 250 kHz Date: 18.SEP.2017 15:18:03 Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 14 of 30 Sheets FCC ID: INRU-G3TB 6. FIELD STRENGTH OF EMISSION 6.1 Provisions Applicable According to §2.1053, measurements shall be made to detect spurious emission that may be radiated directly from the cabinet, control circuits, power leads, or intermediate circuit elements under normal condition of installation and operation. Information submitted shall include the relative radiated power of spurious emission with reference to the rated power output of the transmitter, assuming all emissions are radiated from a halfwave dipole antenna. According to §74.861(e)(6), the mean power of emissions shall be attenuated below the mean output power of the transmitter in accordance with the follwing sceedule: (i) on any frequency removed from the operating frequency by more than 50 percent up to and including 100 percent of the authorized bandwidth: at least 25 dB. (ii)on any frequency removed from the operating frequency by more than 100 percent up to and including 250 percent of the authorized bandwidth: at least 35 dB. (iii) on any frequency removed from the operating frequency by more than 250 percent of the authorized bandwidth shall be attenuated below the unmodulated carrier by at least 43 plus 10 Log(output power in watts) dB. 6.2 Measurement Procedure 1. Setup the configuration per figure 4 and 5 for frequencies measured below and above 1 GHz respectively. 2. For emission frequencies measured below and above 1 GHz, set the spectrum analyzer on a 100 kHz and 1 MHz resolution bandwidth respectively. 3. The search antenna is to be raised and lowered over a range from 1 to 4 meters in horizontally polarized orientation. Position the highness when the highest value is indicated on spectrum analyzer, then change the orientation of EUT on test table over a range from 0。 to 360。with a speed as slow as possible, and keep the azimuth that highest emission is indicated on the spectrum analyzer. Vary the antenna position again and record the highest value as a final reading. A RF test receiver is also used to confirm emissions measured. 4. Repeat step 3 until all frequencies need to be measured were complete. 5. Repeat step 5 with search antenna in vertical polarized orientations. 6. Check the three frequencies of highest emission with varying the placement of cables associated with EUT (if any) to obtain the worse case and record the result. Note: According to 12.7.2(d)(2) of ANSI C63.10-2013: E[dBμV/m] = EIRP[dBm] + 95.2, for d = 3 m. 12.7.2(e) of ANSI C63.10-2013: For conducted measurements below 1000 MHz, the field strength shall be computed as specified in item d), and then an additional 4.7 dB shall be added as an upper bound on the field strength that would be observed on a test range with a ground plane for frequencies between 30 MHz and 1000 MHz, or an additional 6 dB shall be added for frequencies below 30 MHz. Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 15 of 30 Sheets FCC ID: INRU-G3TB Figure 4 : Frequencies measured below 1 GHz configuration Antenna Tower 3m Search Antenna EUT 4m RF Test Receiver Turn 1m 0.8m Table Ground Plane Figure 5 : Frequencies measured above 1 GHz configuration Antenna Tower EUT Horn Antenna 3m 4m Spectrum Analyzer 1.5m Turn 1m Table Amplifier Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 16 of 30 Sheets FCC ID: INRU-G3TB 6.3 Measuring Instrument Equipment Manufacturer Model No. Calibration Date Next Cal. Date EMI Test Receiver Rohde & Schwarz ESU 40 2017/11/15 2018/11/14 Bi-Log Antenna ETC MCTD 2786 2018/07/02 2019/07/01 Horn Antenna EMCO 3115 2017/10/11 2018/10/10 Horn Antenna EMCO 3116 2017/11/15 2018/11/14 Amplifier HP 8447D 2017/12/08 2018/12/07 Amplifier HP 83051A 2018/09/03 2019/09/02 Measuring instrument setup in frequency band measured is as following : Frequency Band Resolution Video Instrument Function (MHz) bandwidth Bandwidth 30 to 1000 Spectrum Analyzer Peak 100 kHz 100 kHz Above 1000 Spectrum Analyzer Peak 1 MHz 1 MHz Rev. 2.0

ire rgornes trar nanent c i900ine recio:mucire 64 Measuring Data 6A.1, Harmonic requences com a soom «2 s n «s ol +5 iA ‘ —rn—— Toss ~—zoow~soon. snn ~~—sorn.~~so0e. Te Frequency (utto te Chanter s2 oue seorm unc «4s oon Anro norronni eur Wieies Hardheld Merephone Model ruoste fove raie Barensv Tenp we Eraireer Ban tane umt ss Te hMose aromnccomnine T Reaime Greaon Rean 1tm Gverimt Dewer tacer rine anoy «s «n in «o rmeome aes rem—| ~ea omec| e rex Tacome ane Sorke tace ow oce rax ow Resilt= Reading+ ConeateFacor ConectedFactr » Artema Fator + Cable Loss « AmpilteGain (any)—EIRP Fctr= iss (ERe Fato«101248 (tie3000o —9.948 300z1i o 2s asn onz Aboro) (ere —cime 21501 3. The margivaliectinit~ Resut

ire rgornes trar nanent s i90sn recio:mucire com a0 ssoou 2 E a0 «s0 «0 +2 ad —|—| ——am——snn Toco —zoon: To Sie Clamber s2 oue snoum in «s oon Anro verncar sur Wieiess Handheid Merephone Moiel suosme Ponetatine Baren 3y Tenp ac Eraiees Bm Hare un s« Te Moce «rommceoinine na reing~| Grem weur tms1 Gnnmt nes: Frter mine couy « «m in «o Tess se es o5 ie e Tez Tmcowo &s1 dose on e in ret roe Resilt= Reading+ ConeateFacor ConectedFactr » Artema Fator + Cable Loss « AmpilteGain (any)—EIRP Fctr: iss (EP racer 301 ast (¥ki.0io 90 kn dncoi) e 95 asn (Ohte Abov) (ern— eiee —23000) 3. The margivaliextinit~ Resut

ire rgornes trar nanent s 1295m recio:mucire 642 Spurious Enissions 10 4znom Frequency (utin Sie Chambesa oue se027 tint s oon An.ro roreonnat sur Wirees Hardheld Mictophone.. Model ruose Pove Raing Baren3¥ Tenp ae Enireer Bran fhang o sn Test Mose «romne—ciirine Te Resing Coreain Reuit bms. Orimt bewcor Faceer rine soy «n d dn «n mane se plorom eocm mm ercom e rex Te sew ce ns ie um |os rac ie sow Se us ow um es rac iz one texs es ie |he—| es rac m se sast ces ohas m eus rac sizoeco Bos ea ons um es rac roe Resilt= Reading+ ConeateFacor 1 Coreced Facior AmennaFactor+ Cable Loss — ApliieGln (any).EIRP Fator: rise (ERe Fato«101248 (tie3000o —9.948 300z1i e 95 asn (Ohte Abows) (en— eiee —23008) 3. The margivaliextinit~ Resut

ire rgornes trar nanent ged ase ree womucire 4znom , > zoi s s Mnsn \ ‘so ron.—aoo: ~son.—aon:—sonc ~s00.— ron.—son.—son.1ot0 Frequency (uttn Sie Clamber s2 oue snoum in «s oon Anro verncar sur Wieiess Handheid Merephone Moiel suosme Ponetatine Baren 3y Tenp ac Eraiees Bm Hiare un s« Te Moce «romme—commne na reing~| Grem weur tms1 Gnnmt nes: Frter mine couy « «m in «o me 5e Ts se is e Tez 2ossce Bezo doss—| aoss ow ons rac Sscc ie Sous Sis w es rak an zo Fom dee ons e |—ece rac se o less ow ie ie |_o# rac e ssco Exm siss ns ow |sesr rak tow Resilt»Reasing+ Cormats accor 1 Coneced Factor » Amerna Factor + Calle Loss —ArmpliteGaln iamy}.EIRP Fator rise (ERe Fato«101248 (tie3000o —9.948 300z1i e 95 asn (Ohte Aboc) (er sire—2190) 3. The maginea init— Resit

ire rgornes trar nanent snurzlousn reco:mucire vom ad soom ‘20 30 0 ‘so Em : ad | \ 1O ross Tw ie Chambes2 sous STom nardhels reptore tw Whder Mre (boceovnu (Ruorre Ponetatine Barer3v Tenp 2e tngres bin han 5« rolinme Wiotine Tew meeec| m ene o ome—| mm —re iiscErcon + onl ns n on > sn sc sc is Hrreas—| inss Sss |—Brie on —Tite—|—fak Gerian|—ear——| l hn n ho erie—| hifi ——fek——fal se ns —|—tee—| S —]—mate—] es —]—fas roe Resilt»Reasing+ Cormats accor 1 Coreced Facior = AmernaFactor+ Cable Loss — ApliieGln (any).EIRP Fator: rise (ERe Fato«101248 (tie3000o —9.948 300z1i e 95 asn (Ohte Aboc) (ern— eiee —21000) 3. The margivaliextinit~ Resut

ire rgornes trar nanent snzeqsn recomucire com ad soom 2 is 0 ‘s0 ES : 0| ‘ l ross—zow oo se Clamber s2 arom nandiss merepiore feal Inre soun (Yoeicu Whhel (hborre Pover atine Barer3v Tenp ime Edres Tiliime tls hss ommctbnne 3« few meam—|—sm— Nesn —ins—| omm—|—€5— io |—ae——re——re——rer e t—|—rer Heims it oi—| 64—( 1e—| e( e en ns en |—on Te t— | ts 5es ies——rex ie —tes——ree imew n se se m 2| es roe Resilt»Reasing+ Cormats accor 1 Coreced Facior = AmernaFactor+ Cable Loss — ApliieGln (any).EIRP Fator: rise (ERe Fato«101248 (tie3000o —9.948 300z1i e 95 asn (Ohte Aboc) (ern— eiee —21000) 3. The margivaliextinit~ Resut

ETC Report No.: 17-07-RBF-021 Sheet 23 of 30 Sheets FCC ID: INRU-G3TB 6.4.3 Emission mask plots * RBW 3 kHz VBW 10 kHz Ref 20 dBm Att 50 dB SWT 225 ms 20 A 10 1 PK VIEW 0 -10 F-MIC -20 -30 -40 -50 -60 -70 -80 Center 470 MHz 200 kHz/ Span 2 MHz Date: 18.SEP.2017 15:04:18 Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 24 of 30 Sheets FCC ID: INRU-G3TB * RBW 3 kHz VBW 10 kHz Ref 20 dBm Att 50 dB * SWT 225 ms 20 A 10 1 PK VIEW 0 -10 F-MIC -20 -30 -40 -50 -60 -70 -80 Center 608 MHz 200 kHz/ Span 2 MHz Date: 18.SEP.2017 15:15:21 Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 27 of 30 Sheets FCC ID: INRU-G3TB 7. FREQUENCY STABILITY MEASUREMENT 7.1 Provisions Applicable According to §2.1055 (a)(1), the frequency stability shall be measured with variation of ambient temperature from -30 to +50 centigrade. According to §2.1055 (d)(1), the frequency stability shall be measured with variation of primary supply voltage from 85 to 115 percent of the nominal value for other than hand carried battery equipment. According to § 2.1055 (d)(2), for hand carried, battery powered equipment, reduce primary supply voltage to the battery operating end point which shall be specified by the manufacturer. According to §74.861(e)(4), the frequency tolerance of the transmitter shall be 0.005 percent. 7.2 Measurement Procedure A) Frequency stability versus environmental temperature 1. Setup the configuration per figure 6 for frequencies measured at an environmental chamber. 2. Turn on EUT and set SA center frequency to the right frequency needs to be measured. Set SA RBW to 30 kHz, VBW to 100kHz and frequency span to 500 kHz. Then turn off the EUT. 3. Set the temperature of chamber to 50℃. Allow sufficient time for the temperature of the chamber to stabilize. While maintaining a constant temperature inside the chamber, turn the EUT on and measure the EUT operating frequency when the frequency has stablized. 4. Repeat step 3 with a 10℃ decreased per stage until the lowest temperature -30℃ is measured, record all measurement frequencies. B) Frequency stability versus input voltage 1. Setup the configuration per figure 6 for frequencies measured at an environmental chamber set for a temperature of 25℃. Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 28 of 30 Sheets FCC ID: INRU-G3TB 2. Set SA center frequency to the right frequency needs to be measured. Then set SA RBW to 30 kHz, VBW to 100kHz and frequency span to 500 kHz. 3. Supply the EUT primary voltage with 85 and 115 percent of the nominal value and record the frequency. Figure 6 : Frequency stability measurement configuration Temperature Chamber Spectrum Analyzer DC Power Supply 7.3 Measurement Instrument Equipment Manufacturer Model No. Calibration Date Next Cal. Date Spectrum Analyzer Rohde & Schwarz FSP40 2017/11/02 2018/11/01 Temperature Chamber ESPEC EFL-3 2018/07/26 2019/07/25 Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 29 of 30 Sheets FCC ID: INRU-G3TB 7.4 Measurement Data Test Date : Aug. 27, 2018 Temperature : 23 °C Humidity : 68 % A. Tx Frequency 470 MHz A1. Frequency stability versus enviroment tempture Reference Frequency 470 MHz Limit：0.005% Enviroment Power (MHz) (%) Tempture Supplied (℃) (Vdc) 50 520.0662 0.00312 40 520.0443 -0.00110 30 520.0433 -0.00129 20 3.0 520.0490 -0.00019 10 520.0447 -0.00102 0 520.0481 -0.00037 -10 520.0533 0.00063 -20 520.0693 0.00371 -30 520.0661 0.00310 A2. Frequency stability versus supplied voltage Reference Frequency : 470 MHz Limit：0.005% Enviroment Power (MHz) (%) Tempture Supplied (℃) (Vdc) 25 2.5 520.0667 0.00321 25 3.5 520.0504 0.00008 Rev. 2.0

ETC Report No.: 17-07-RBF-021 Sheet 30 of 30 Sheets FCC ID: INRU-G3TB Test Date : Aug. 27, 2018 Temperature : 23 °C Humidity : 68 % 8 CONDUCTED EMISSION MEASUREMENT 8.1 Standard Applicable This EUT is excused from investigation of conducted emission, for it is powered by DC battery only. According to §15.207 (d), measurements to demonstrate compliance with the conducted limits are not required for devices which only employ battery power for operation and which do not operate from the AC power lines or contain provisions for operation while connected to the AC power lines. Rev. 2.0


Document Created: 2018-10-04 14:15:32
Document Modified: 2018-10-04 14:15:32
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC