Test Report

FCC ID: IKQMGQ

Test Report

Download: PDF
FCCID_4483477

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 1 of 24 TEST REPORT Application No.: SZEM1908017369CR Applicant: Scosche Industries Inc Address of Applicant: 1550 Pacific Ave Oxnard California United States 93033 Manufacturer: Scosche Industries Inc Address of Manufacturer: 1550 Pacific Ave Oxnard California United States 93033 Factory: Scosche Industries Inc Address of Factory: 1550 Pacific Ave Oxnard California United States 93033 Equipment Under Test (EUT): EUT Name: Wireless Car Charger Model No.: MGQ, MGQWDDP-AP2, MGQVP-AP2, MGQDWD-CP0, MGQWDDP-XTET, MGQVP-XTET, MGQWD-XTET, MGQD-XTET, MGQXX-XX (XX can be A-Z or 0-9, the first “XX” stands for mount base, the second “XX” stands for customer coder) ♣ ♣ Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. Trade mark: SCOSCHE FCC ID: IKQMGQ Standard(s) : 47 CFR Part 15, Subpart C Date of Receipt: 2019-08-12 Date of Test: 2019-08-12 to 2019-08-14 Date of Issue: 2019-08-19 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Keny Xu EMC Laboratory Manager

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 2 of 24 Revision Record Version Chapter Date Modifier Remark 01 2019-08-19 Original Authorized for issue by: Harry Wu /Project Engineer Eric Fu /Reviewer

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 3 of 24 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result 47 CFR Part 15, 47 CFR Part 15, Subpart Antenna Requirement N/A Pass Subpart C C 15.203 Radio Spectrum Matter Part Item Standard Method Requirement Result 47 CFR Part 15, ANSI C63.10 (2013) 47 CFR Part 15, Subpart 20dB Bandwidth Pass Subpart C Section 6.9.2 C 15.215 47 CFR Part 15, ANSI C63.10 (2013) 47 CFR Part 15, Subpart Restricted Bands Pass Subpart C Section 6.10.5 C 15.205 Radiated Emissions 47 CFR Part 15, ANSI C63.10 (2013) 47 CFR Part 15, Subpart Pass (9kHz-30MHz) Subpart C Section 6.4 C 15.205 & 15.209 Radiated Emissions 47 CFR Part 15, ANSI C63.10 (2013) 47 CFR Part 15, Subpart Pass (30MHz-1GHz) Subpart C Section 6.5 C 15.205 & 15.209 Declaration of EUT Family Grouping: Model No.: MGQ, MGQWDDP-AP2, MGQVP-AP2, MGQDWD-CP0, MGQWDDP-XTET, MGQVP-XTET, MGQWD-XTET, MGQD-XTET, MGQXX-XX (XX can be A-Z or 0-9, the first “XX” stands for mount base, the second “XX” stands for customer coder) Only the model MGQ was tested, since the electrical circuit design, layout, components used, internal wiring and functions were identical for the above models, with only difference on model name, mount base and packaging.

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 4 of 24 3 Contents Page 1 COVER PAGE ...... ... .cc ce en eenenerererreverererereererereererereeererereeereeeeereereeeeereeeneereeeneeneeveeneeneene en nenne en nennnvvvenenennnn 1 2 TEST SUMMARY ....... ... . e0 0000000006 06090rererereererereerererereererere e reeere e reeeeeaereereeneeeneene en eeeenenne en nennnevvenennnnvvenene 3 3 CONTENTS. 4 GENERAL INFORMATION ......... o0 eeeremreereereeermereeermereeermereeermerereeneneereeenmeereeenmeereennnenrenrnne 5 4.1 DETAILS OF E—ULT ; .. 220 en en en en m en eere en en e en en en en en en en en en en en en en eneve en en evee en enevee en enevneeenenenee n 5 4.2 Description or Support Units .5 4.3 MEASUREMENT UNCERTAINTY ..... .5 4.4 TEST LOCATION .6 4.5 TEest Faciuty.. .6 4.6 DEVIATION FROM STANDARDS. .6 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ..... .. ... . en en en eene m en en en en en en en en en en en en enevnenenenene 6 5 EQUIPMENT LIST ...... .ce eeeremreermmereeermereeermereeermereeermereeermerereenereeenmeeneereeenmeereennmeereeennnenre en 7 6 RADIO SPECTRUM TECHNICAL REQUIREMENT .........0.000000 0e eeermeereeermeeneereennmeerereennmerennmeeren n 9 6.1 ANTENNA REQUIREMENT .. .9 6.1.1 Test Requirement:..... .9 6.1.2 CONGIUSION ............l.ccsceereeememereveveerereeeenrereeenerereeenerereeenerereveeneneneneenenennenev en neneveenenenevnenenenevee n 9 7 RADIO SPECTRUM MATTER TEST RESULTS .......... cce eememmeeermnereeermereeermeneereeenmnmeereenmeereennmenrenee 10 7.1 200B BANDWIDTH.... 7.1.1 EU.T. Operation 7.1.2 Test S@tup Di@graM ....c.c.cclll 7.1.3 Measurement Procedure and Data. 7.2 RestTRICTED BaNDs .... 7.2.1 E.U.T. Operation.. 7.2.2 Test Setup Diagram 7.2.3 Measurement Procedure and Data. 7.3 RADIATED EMISSIONS (OKHz—30MHz)..... 7.3.1 E.U.T. Operation..... 7.3.2 Test Setup Diagram 7.3.3 Measurement Procedure and Data. 7.4 RADIATED EMISSIONS (3OMHz—1GHz). 7.4.1 EU.T. OD@AtiON......cccscccee. 7.4.2 Test SQ@tup Di@Qr@M ...z 7.4.3 Measurement Procedure and Data. 8 PHOTOGRAPHS..............ccommemmmeemmreemereemereeemereeemereeermerereeermeeenmeeneereeenmeereeenmeereennnenrc en 24 8.1 ces S e 24 8.2 EUT CONSTRUCTIONAL DETAILS (EUT PHOTOS)......... cesmm en en en en n m en n eneerenenenene en en en 24 Unless otherwise agreed in writing, this document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at hitp/waw.sas..comen/Terms—and—Conditions.aspx and, for electronic format documents, Subject to Terms and Gonditions for Electronte Documents at hylwim sgs. comfenTerms—ang:Condiions/erms.6.booument aspx. Attention is drawn to the limitation of lability, indamnification and jurlsdiction issues defined tharein. Any holder of this document is advised that information contained hereon raflects the Company‘s findings at the time of ts intervention only and within the limits of Clients instructions, if any. The Company‘s sole responsibiity is to its Client and this document does not exoncrate parties to a fransaction from exereising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or CR . appearance of this documentis unlawful and offendars may be prosecuted to the fullest extent of the law. Unlss othenwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. ng Sevies 4P Aftention: To check the authenticity of testing /inspection report & certificate, please contact us at télophone: (86—755) 8307 1443, or email: CN.Doecheck@sgs.com 0oi No.t Wortshap, N—10, d Secton, Science 8 Technology Pars Shenzhen, Cina 518057 t (86—755) 26012053 f (86—758) 26710504 wimsgsgroup.com.en aboclory fB BAARdERN—10K—S1B #B4i: 518057 t (€6—755)26012050 f (@6—755) 26710504 sgs:china@sgs.com t Member of the SGS Group (SGS SA)

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 5 of 24 4 General Information 4.1 Details of E.U.T. Power supply: Input: DC5V,3A / DC9V,2A / DC12V,1.5A Output: 5W/7.5W/10W/15W Car charger model: CQA8 Input: DC12V, 1.8A Output: DC3.6-6.5V, 3A / 6.5-9V, 2A / 9-12V, 1.5A, 2.0A Max. Cable: Type C cable: 150cm, Unshielded Operation Frequency: 110.577kHz to 147.115kHz Modulation Type: Load Modulation Antenna Type: Loop Antenna Antenna Gain: 0dBi Remark: Tests were conducted in all load modes and the worst case (DC 9V/1.67A Input) is reported only. 4.2 Description of Support Units Description Manufacturer Model No. Serial No. iPhone 8 Apple A1863 F4GVQ656JC6D SAMSUNG Galaxy S8 SAMSUNG SM-G9500 R28J9140LPB Mobile Phone XIAOMI M1902F1A 22006/K9SH018 4.3 Measurement Uncertainty No. Item Measurement Uncertainty 1 Radio Frequency ± 7.25 x 10-8 2 Occupied Bandwidth ± 3% ± 4.5dB (Below 1GHz) 3 RF Radiated power ± 4.8dB (Above 1GHz) ± 4.5dB (Below 1GHz) 4 Radiated Spurious emission test ± 4.8dB (Above 1GHz) 5 Temperature test ± 1°C 6 Humidity test ± 3% 7 Supply voltages ± 1.5% 8 Time ± 3%

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 6 of 24 4.4 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Shenzhen, Guangdong, China. 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. 4.5 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 3m Fully-anechoic chamber for above 1GHz, 10m Semi-anechoic chamber for below 1GHz, Shielded Room for Mains Port Conducted Interference Measurement and Telecommunication Port Conducted Interference Measurement of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-20026, R-14188, C-12383 and T-11153 respectively. • FCC –Designation Number: CN1178 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: 406779. • Innovation, Science and Economic Development Canada SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized by ISED as an accredited testing laboratory. CAB identifier: CN0006. IC#: 4620C. 4.6 Deviation from Standards None 4.7 Abnormalities from Standard Conditions None

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 7 of 24 5 Equipment List 20dB Bandwidth Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date Shielding Room SAEMC MSR733 SEM001-09 2019-06-13 2024-06-12 DC Power Supply ZhaoXin RXN-305D SEM011-02 2018-09-25 2019-09-24 Spectrum Analyzer Rohde & Schwarz FSP SEM004-06 2018-09-27 2019-09-26 JS1120-2 Measurement Software JS Tonscend N/A N/A N/A BT/WIFI V2. Coaxial Cable SGS N/A SEM031-02 2019-07-11 2020-07-10 Attenuator Weinschel Associates WA41 SEM021-09 N/A N/A Signal Generator KEYSIGHT N5173B SEM006-05 2018-09-27 2019-09-26 Power Meter Rohde & Schwarz NRVS SEM014-02 2018-09-25 2019-09-24 Electric and Magnetic NBM- Narda EMC2143 2018-02-07 2020-02-06 Field Analyzer 550/EHP-50F Electric Field Probe WANDEL & EMR-20 EMC0907 2019-05-21 2020-05-20 (100KHz-3GHz) GOLTERMANN EMF Tester Narda ELT-400 SZE039-4 2019-07-08 2020-07-07 Restricted Bands Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date Shielding Room SAEMC MSR733 SEM001-09 2019-06-13 2024-06-12 DC Power Supply ZhaoXin RXN-305D SEM011-02 2018-09-25 2019-09-24 Spectrum Analyzer Rohde & Schwarz FSP SEM004-06 2018-09-27 2019-09-26 JS1120-2 Measurement Software JS Tonscend N/A N/A N/A BT/WIFI V2. Coaxial Cable SGS N/A SEM031-02 2019-07-11 2020-07-10 Attenuator Weinschel Associates WA41 SEM021-09 N/A N/A Signal Generator KEYSIGHT N5173B SEM006-05 2018-09-27 2019-09-26 Power Meter Rohde & Schwarz NRVS SEM014-02 2018-09-25 2019-09-24 Electric and Magnetic NBM- Narda EMC2143 2018-02-07 2020-02-06 Field Analyzer 550/EHP-50F Electric Field Probe WANDEL & EMR-20 EMC0907 2019-05-21 2020-05-20 (100KHz-3GHz) GOLTERMANN EMF Tester Narda ELT-400 SZE039-4 2019-07-08 2020-07-07 Radiated Emissions (9kHz-30MHz) Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date 10m Semi-Anechoic SAEMC FSAC1018 SEM001-03 2018-03-31 2021-03-30 Chamber e3 V8.2014-6- Measurement Software AUDIX N/A N/A N/A 27

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 8 of 24 Coaxial Cable SGS N/A SEM029-01 2019-07-11 2020-07-10 EMI Test Receiver Rohde & Schwarz ESR SEM004-03 2019-04-01 2020-03-31 (9kHz-7GHz) BiConiLog Antenna ETS-LINDGREN 3142C SEM003-02 2019-05-24 2022-05-23 (26-3000MHz) Sonoma Instrument Pre-amplifier 310N SEM005-04 2019-04-12 2020-04-11 Co Active Loop Antenna ETS-Lindgren 6502 SEM003-08 2017-08-22 2020-08-21 Radiated Emissions (30MHz-1GHz) Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date 10m Semi-Anechoic SAEMC FSAC1018 SEM001-03 2018-03-31 2021-03-30 Chamber e3 V8.2014-6- Measurement Software AUDIX N/A N/A N/A 27 Coaxial Cable SGS N/A SEM029-01 2019-07-11 2020-07-10 EMI Test Receiver Rohde & Schwarz ESR SEM004-03 2019-04-01 2020-03-31 (9kHz-7GHz) BiConiLog Antenna ETS-LINDGREN 3142C SEM003-02 2019-05-24 2022-05-23 (26-3000MHz) Sonoma Instrument Pre-amplifier 310N SEM005-04 2019-04-12 2020-04-11 Co Active Loop Antenna ETS-Lindgren 6502 SEM003-08 2017-08-22 2020-08-21 General used equipment Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date Shanghai Humidity/ Temperature Meteorological ZJ1-2B SEM002-03 2018-09-27 2019-09-26 Indicator Industry Factory Shanghai Humidity/ Temperature Meteorological ZJ1-2B SEM002-04 2018-09-27 2019-09-26 Indicator Industry Factory Humidity/ Temperature Mingle N/A SEM002-08 2018-09-27 2019-09-26 Indicator Changchun Barometer Meteorological DYM3 SEM002-01 2019-04-04 2020-04-03 Industry Factory

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 9 of 24 6 Radio Spectrum Technical Requirement 6.1 Antenna Requirement 6.1.1 Test Requirement: 47 CFR Part 15, Subpart C 15.203 Limit: 6.1.2 Conclusion Standard Requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit permanently attached antenna or of an so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. EUT Antenna: The antenna is integrated on the main PCB and no consideration of replacement. The best case gain of the antenna is 0dBi. Antenna location: Refer to Appendix(Internal photos)

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 10 of 24 7 Radio Spectrum Matter Test Results 7.1 20dB Bandwidth Test Requirement 47 CFR Part 15, Subpart C 15.215 Test Method: ANSI C63.10 (2013) Section 6.9.2 Limit: NA 7.1.1 E.U.T. Operation Operating Environment: Temperature: 26.6 °C Humidity: 43.8 % RH Atmospheric Pressure: 1000 mbar Pretest these a:Charge mode_Keep the EUT charging(5W). modes to find b:Charge mode_Keep the EUT charging(7.5W). the worst case: c:Charge mode_Keep the EUT charging(10W) d:Charge mode_Keep the EUT charging(15W) The worst case d:Charge mode_Keep the EUT charging(15W) for final test: 7.1.2 Test Setup Diagram 7.1.3 Measurement Procedure and Data

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 11 of 24 * RBW 10 Hz Marker 1 [T1 ] * VBW 30 Hz -42.91 dBm Ref -20 dBm * Att 10 dB SWT 1 s 110.900000000 kHz -20 ndB [T1] 20.00 dB BW 25.961538462 Hz -30 Temp 1 [T1 ndB] A -62.71 dBm 1 PK 110.887019231 kHz VIEW -40 1 Temp 2 [T1 ndB] -62.86 dBm 110.912980769 kHz -50 -60 T1 T2 -70 3DB -80 -90 -100 -110 -120 Center 110.9 kHz 10 Hz/ Span 100 Hz * RBW 10 Hz Marker 1 [T1 ] * VBW 30 Hz -42.47 dBm Ref -20 dBm * Att 10 dB SWT 1 s 147.100000000 kHz -20 ndB [T1] 20.00 dB BW 26.121794872 Hz -30 Temp 1 [T1 ndB] A -62.55 dBm 1 PK 147.086858974 kHz VIEW 1 -40 Temp 2 [T1 ndB] -62.66 dBm 147.112980769 kHz -50 -60 T1 T2 -70 3DB -80 -90 -100 -110 -120 Center 147.1 kHz 10 Hz/ Span 100 Hz

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 12 of 24 7.2 Restricted Bands Test Requirement 47 CFR Part 15, Subpart C 15.205 Test Method: ANSI C63.10 (2013) Section 6.10.5 Limit: The fundamental wave can not fall in the restricted band 90KHz-110KHz 7.2.1 E.U.T. Operation Operating Environment: Temperature: 26.6 °C Humidity: 43.8 % RH Atmospheric Pressure: 1000 mbar Pretest these a:Charge mode_Keep the EUT charging(5W). modes to find b:Charge mode_Keep the EUT charging(7.5W). the worst case: c:Charge mode_Keep the EUT charging(10W) d:Charge mode_Keep the EUT charging(15W) The worst case d:Charge mode_Keep the EUT charging(15W) for final test: 7.2.2 Test Setup Diagram 7.2.3 Measurement Procedure and Data

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 13 of 24 * RBW 1 kHz Marker 1 [T1 ] * VBW 3 kHz -39.44 dBm Ref -10 dBm * Att 10 dB SWT 100 ms 129.006410256 kHz -10 OBW 36.538461538 kHz Temp 1 [T1 OBW] -20 -46.20 dBm A 110.576923077 kHz 1 PK Temp 2 [T1 OBW] VIEW -30 -49.99 dBm 147.115384615 kHz 1 -40 T1 T2 -50 -60 3DB -70 -80 -90 -100 -110 Start 100 kHz 10 kHz/ Stop 200 kHz According the test data of Radiated Emission(9-150KHz) in clause 7.3, the fundamental wave is not fall in the restricted band 90KHz-110KHz, the field strength also meet the 15.209 requirement, so this test is Pass.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 14 of 24 7.3 Radiated Emissions (9kHz-30MHz) Test Requirement 47 CFR Part 15, Subpart C 15.205 & 15.209 Test Method: ANSI C63.10 (2013) Section 6.4 Measurement Distance: 3m Limit: Frequency(MHz) Field strength(microvolts/meter) Measurement distance(meters) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 Remark: The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands 9-90kHz, 110-490kHz. Radiated emission limits in these three bands are based on measurements employing an average detector, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. If field strength is measured at only a single point, then that point shall be at the radial from the EUT that produces the maximum emission at the frequency being measured, as described in 5.4. If that point is closer to the EUT than λ/2π and the limit distance is greater than λ/2π, the measurement shall be extrapolated to the limit distance by conservatively presuming that the field strength decreases at a 40 dB/decade of distance rate to the λ/2π distance, and at a 20 dB/decade of distance rate beyond λ/2π. This shall be accomplished using Equation (2): FS(10m) = FS(30/300m) + 40log{d(near field)/d(10m)} + 20log{d(30/300m)/d(near field)} (2) If the single point measured is at a distance greater than λ/2π, then extrapolation to the limit distance shall be calculated using Equation (3): FS(10m) = FS(30/300m) + 20log{d(30/300m)/d(10m)} (3) If both the single point and the limit distance are equal to or closer to the EUT than λ/2π, then extrapolation to the limit distance shall be calculated using Equation (4): FS(10m) = FS(30/300m) + 40log{d(30/300m)/d(10m)} (4) Remark: dnear field = 47.77 / fMHz where fMHz is the frequency of the emission being measured in MHz.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 15 of 24 7.3.1 E.U.T. Operation Operating Environment: Temperature: 25 °C Humidity: 45 % RH Atmospheric Pressure: 1000 mbar Pretest these a:Charge mode_Keep the EUT charging(5W). modes to find b:Charge mode_Keep the EUT charging(7.5W). the worst case: c:Charge mode_Keep the EUT charging(10W) d:Charge mode_Keep the EUT charging(15W) The worst case b:Charge mode_Keep the EUT charging(7.5W). for final test: 7.3.2 Test Setup Diagram 7.3.3 Measurement Procedure and Data For testing performed with the loop antenna, the center of the loop was positioned 1 m above the ground and positioned with its plane vertical at the specified distance from the EUT. During testing the loop was rotated about its vertical axis for maximum response at each azimuth and also investigated with the loop positioned in the horizontal plane. Only the worst position of vertical was shown in the report.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 16 of 24 Mode:b, Detector:Peak

Level (dBuV/im) 140 Condition: 3m Job No. : 17369CR Test Mode: b Cable Ant Preamp Read Limit Over Freq Loss Factor Factor Level Level Lline Llimit MHz dB dB/m dB dBuV dBuV/m dBuV/m dB 1 0.187 @.07 11.83 32.21 75.85 55.54 102.15 —46.61 2 pp ©.595 @.14 11.83 32.25 68.26 47.98 72.12 —24.14 3 3.720 @.40 12.13 32.30 50.42 30.65 69.54 —38.89 Unless otherwise agreed in writing, this document is issued by the Company subject to its General Conditions of Service printed overieaf, available on request or accessible at hitp:\win.sgs.comen/Terms—and—Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at htipyTwin#. xc Attention is drawn to the limitation of lability, indamnification and Juriediction y holder of this document is advised that information contained hereon raflects the Cof s lindings at the time of is Intervention only and within the limite of Client‘s instructions, if any. The Company‘s sole responsibiity is to its Client and this document does not exonerate parties to a fransaction from exércising all their rights and obligations under the transaction documents. This document cannot be reproduced excent in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content of Hoblinnl t / 0t T appearanceof this document is unlawiul and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the %Inmmmflmm gerices§ results shown in this test report refer only to the sample() tested and such sample(s) are retained for 30 days only. Ml-nllnn To check the num-nn:uy testing !inspection report & certificate, please contact us at mapnon. (s6—755)as07 1443, all: CN.Doccheck@sas. Nn1wmkshup.M+10,Midde Secton, Sfimw&Tmnulogme Shenthen,Chine §18057.. t (6—750)20012058 1 (86—755) 26710504 wincsgegroup.comn fB BAABRdERN—10K—S1B #B4i: s1eos7 t (B6—758)26012053 1 (@6—755) 26710504 spschina@sys.com I Member of the SGS Group (SGS SA)

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 18 of 24 7.4 Radiated Emissions (30MHz-1GHz) Test Requirement 47 CFR Part 15, Subpart C 15.205 & 15.209 Test Method: ANSI C63.10 (2013) Section 6.5 Measurement Distance: 10m Limit: Frequency(MHz) Field strength(microvolts/meter) Measurement distance(meters) 30-88 100 3 88-216 150 3 216-960 200 3 Above 960 500 3 Remark: The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 19 of 24 7.4.1 E.U.T. Operation Operating Environment: Temperature: 25 °C Humidity: 45 % RH Atmospheric Pressure: 1000 mbar Pretest these a:Charge mode_Keep the EUT charging(5W). modes to find b:Charge mode_Keep the EUT charging(7.5W). the worst case: c:Charge mode_Keep the EUT charging(10W) d:Charge mode_Keep the EUT charging(15W) The worst case b:Charge mode_Keep the EUT charging(7.5W). for final test: 7.4.2 Test Setup Diagram

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 20 of 24 7.4.3 Measurement Procedure and Data a. The EUT was placed on the top of a rotating table 0.8 meters above the ground for below 1GHz at a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. g. Test the EUT in the lowest channel,the middle channel,the Highest channel h. The radiation measurements are performed in X, Y, Z axis positioning for Transmitting mode,And found the X axis positioning which it is worse case. i. Repeat above procedures until all frequencies measured was complete. Remark: Level= Read Level+ Cable Loss+ Antenna Factor- Preamp Factor

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 21 of 24 Mode:b; Polarization:Horizontal, Detector:Quasi-peak

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 22 of 24 Mode:b; Polarization:Vertical, Detector:Quasi-peak

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 23 of 24 The test was performed at a 10m test site. According to below formulate and the test data at 10m test distance, L3 / L10 = D10 / D3 Note: L3: Level @ 3m distance. Unit: uV/m; L10: Level @ 10m distance. Unit: uV/m; D3: 3m distance. Unit: m D10: 10m distance. Unit: m The level at 3m test distance is below: Level @ Frequency Level @ Level @ 3m Level @ 3m Limit @ 3m Ant. 10m Margin (dB) (MHz) 10m (uV/m) (uV/m) (dBuV/m) (dBuV/m) Polarization (dBuV/m) 37.94 25.76 19.41 64.70 36.22 40.00 -3.78 V 43.51 26.06 20.09 66.97 36.52 40.00 -3.48 V 130.38 14.61 5.38 17.92 25.07 43.50 -18.43 V 350.48 19.17 9.09 30.30 29.63 46.00 -16.37 V 547.10 24.32 16.44 54.81 34.78 46.00 -11.22 V 869.13 27.91 24.86 82.87 38.37 46.00 -7.63 V 30.53 17.01 7.09 23.63 27.47 40.00 -12.53 H 37.94 15.45 5.92 19.74 25.91 40.00 -14.09 H 172.60 12.80 4.37 14.55 23.26 43.50 -20.24 H 350.48 19.50 9.44 31.47 29.96 46.00 -16.04 H 742.26 26.99 22.36 74.54 37.45 46.00 -8.55 H 922.52 28.98 28.12 93.73 39.44 46.00 -6.56 H

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801736901 Page: 24 of 24 8 Photographs 8.1 Test Setup Refer to Setup Photos 8.2 EUT Constructional Details (EUT Photos) Refer to EUT external and internal photos - End of the Report -


Document Created: 2019-10-18 02:57:29
Document Modified: 2019-10-18 02:57:29
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC