RF Exposure Part 4

FCC ID: IHDT56XS2

RF Exposure Info

Download: PDF
FCCID_4287341

In Collaboration with Add: No.51 Xueyuan Road, Haidie District, Beijing, 100191, China +86—10—62304633—2079 F : +86—10—62304633—2504 E—mail: ettl@chinattl.com hitp://www.chinattl.en Appendix (Additional assessments outside the scope of CNAS LO0570) Antenna Parameters with Head TSL Impedance, transformed to feed point 52.40— 2.59J0 Return Loss —29.30B Antenna Parameters with Body TSL Impedance, transformed to feed point 51.60— 3.86)0 Return Loss —27.70B General Antenna Parameters and Design Electrical Delay (one direction) 0.898 ns After long term use with 100W radiated power, only a slight warming ofthe dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antennais therefore short—circuited for DC—signals. On some of thedipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z19—6008 1 Page 4 of 8

r« In Collaboration with a @77 CALIBRATION dn LABORATORY Add: No.51 Xueyuan Road, HaidianDistrict, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com http=//www.chinattl.en DASYS Validation Report for Head TSL Date: 03.26.2019 Test Laboratory: CTTL, Beijing, China DUT: Dipole 750 MHz; Type: D750V3; Serial: D750V3 — SN: 1087 Communication System: UID 0, CW; Frequency: 750 MHz; Duty Cycle: 1:1 Medium parameters used: {= 750 MHz; 0 = 0.903 S/m; & = 43.01; p = 1000 kg/m3 Phantom section: Right Section DASYS Configuration: «+ Probe: EX3DV4 — SN3617; ConvF(10.03, 10.03, 10.03) @ 750 MHz; Calibrated: 1/31/2019 *« Sensor—Surface: 1.4mm (Mechanical Surface Detection) + Electronics: DAE4 Sn1331; Calibrated: 2/6/2019 * Phantom: MFP_V5.1C ; Type: QD 000 PS1CA; Serial: 1062 + Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7450) Dipole Calibration/Zoom Sean (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 55.05 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 3.00 W/kg SAR(I g) =2.1 W/kg; SAR(10 g) = 1.42 W/kg Maximum value of SAR (measured) =2.72 W/kg —1.86 —3.11 5.57 —T A2 —9.28 0 dB =2.72 W/kg =4.35 dBW/kg Certificate No: Z19—60081 Page 5 of 8

=‘TTLM a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinatt.com hitp://www.chinattl.en Impedance Measurement Plot for Head TSL Tri sil Log mag 10. 00de/ ref 0.000de (ri] I 5990 r53~750.00000 mz =251 265 do ~ 40. 00 30.00 20.00 10. 00 0.000)) 8 —20.00 ~20.00 1 ~30.00 ~40. 00 —50.00 x BM 511 snith (R+Jx) scale 1.000U [F1 vel] »1. 750.00000 mz 52.389 n —2.5920 n [1" Star so Niz wew 100 He Stop 960 Niz -ITI Certificate No: Z19—6008 1 Page 6 of 8

‘4 in Collaboration with 7]J;J, a ‘ CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinatt.com hitp://www.chinattl.en DASYS Validation Report for Body TSL Date: 03.26.2019 Test Laboratory: CTTL, Beijing, China DUT: Dipole 750 MHz; Type: D750V3; Serial: D750V3 — SN: 1087 Communication System: UID 0, CW; Frequency: 750 MHz; Duty Cycle: 1:1 Medium parameters used: {= 750 MHz; 0 = 0.935 $/m; &, = 56.85; p = 1000 kg/m3 Phantom section: Center Section DASYS Configuration: * Probe: EX3DV4 — SN3617; ConvF(9.85, 9.85, 9.85) @ 750 MHz; Calibrated: 1/31/2019 * Sensor—Surface: 1.4mm (Mechanical Surface Detection) + Electronics: DAE4 Sn1331; Calibrated: 2/6/2019 + Phantom: MFP_V5.1C ; Type: QD 000 P51CA; Serial: 1062 * Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7450) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 53.71 V/m; Power Drift= 0.01 dB Peak SAR (extrapolated) = 3.08 W/kg SAR(I g) =2.09 W/kg; SAR(10 g) = 1.41 W/kg Maximum value of SAR (measured) =2.75 W/kg —1.94 —3.89 5.83 —7.18 —9.72 0 dB =2.75 W/kg = 4.39 dBW/kg Certificate No: Z19—6008 1 Page 7 of 8

TTL CALIBRATION foBictoillk LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitp://www.chinattl.en Impedance Measurement Plot for Body TSL Tri iT tog may 10. 00087 ner 0. oods [Fi] 5990 rsa—750,00000 mz =27. 744 ds 40.00 30. 00 20.00 10.00 0.000p) ra —10.00 ~20. 00 ~30. 00 ~40.00 ~5o. 00 x BMR 12. smith (ReJ®) scale 1.000U [r2 be1] »1. 750.00000 mz 51.570 n —3.8607 o 54.961 _ / M5 [1stt sso mz ww 100 e Sten Sso mtz IMI Certificate No: Z19—60081 Page 8 of 8

b‘* In Collaboration with \\\\\\wn’ty By C B M ¢ gl CALIBRATION LABORATORY im ARAUA mm o — Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China 4,,//,\%\3 v CALIBRATION Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 C ARDY CNAS LO570 E—mail: cttl@chinattl.com http://www.chinattl.cn Client Sporton Certificate No: Z219—60082 CALIBRATION CERTIFICATE Object D835V2 — SN: 40151 Calibration Procedure(s) FF—211—003—01 Calibration Procedures for dipole validation kits Calibration date: March 27, 2019 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(Sl). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(22+3)‘c and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRP2 106277 20—Aug—18 (CTTL, No.J18X06862) Aug—19 Power sensor NRPBS 104291 20—Aug—18 (CTTL, No.J18X06862) Aug—19 Reference Probe EX3DV4 SN 3617 31—Jan—19(SPEAG,No.EX3—3617_Jan19) Jan—20 DAE4 SN 1331 06—Feb—19(SPEAG,No.DAE4—1331_Feb19) Feb—20 Secondary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Signal Generator E4438C MY49071430 23—Jan—19 (CTTL, No.J19X00336) Jan—20 NetworkAnalyzer E5071C MY46110673 24—Jan—19 (CTTL, No.J19XK00547) Jan—20 Name Function Signature Calibrated by: Zhao Jing SAR Test Engineer ‘Z(?J Reviewed by: Lin Hao SAR Test Engineer I‘fifli% Approved by: Qi Dianyuan SAR Project Leader % Issued: March 30, 2019 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: Z19—60082 Page 1 of 8

A'N In Collaboration with e § _p__€_ _a@ _0 g—‘T]-L CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.cn Glossary: TSL tissue simulating liquid ConvrF sensitivity in TSL / NORMx,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for assessment of specific absorption rate of human exposure to radio frequency fields from hand—held and body—mounted wireless communication devices— Part 1: Device used next to the ear (Frequency range of 300MHz to 6GHz)", July 2016 c) IEC 62209—2, "Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices used in close proximity to the human body (frequency range of 30MHz to 6GHz)", March 2010 d) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. Certificate No: Z19—60082 Page 2 of 8

In Collaboration with a ® s/"]/‘] Faaal CALIBRATION LABORATORY y Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http:/www.chinattl.en Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY52 52.10.2.1495 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom 5.1C Distance Dipole Center — TSL 15 mm with Spacer Zoom Scan Resolution dx, dy, dz = 5 mm Frequency 835 MHz +1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 41.5 0.90 mho/m Measured Head TSL parameters (22.0 £ 0.2) °C 42.7 £6 % 0.93 mho/m +6 % Head TSL temperature change during test <1.0 °C SAR result with Head TSL SAR averaged over 1 Cm" (1 g) of Head TSL Condition SAR measured 250 mW input power 2.36 Wikg SAR for nominal Head TSL parameters normalized to 1W 9.30 Wikg * 18.8 % (k=2) SAR averaged over 10 ecm (10 g) of Head TSL Condition SAR measured 250 mW input power 1.56 Wikg SAR for nominal Head TSL parameters normalized to 1W 6.16 Wikg * 18.7 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 665.2 0.97 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 56.7 +6 % 0.94 mho/m +6 % Body TSL temperature change during test <1.0 °C SAR result with Body TSL SAR averaged over 1 Cm° _(1 g) of Body TSL Condition SAR measured 250 mW input power 2.32 Wikg SAR for nominal Body TSL parameters normalized to 1W 9.53 W /kg * 18.8 % (k=2) SAR averaged over 10 ecm (10 g) of Body TSL Condition SAR measured 250 mW input power 1.52 Wikg SAR for nominal Body TSL parameters normalized to 1W 6.20 Wikg + 18.7 % (k=2) Certificate No: Z19—60082 Page 3 of 8

8 In Collaboration with mm @eJ~J;j, CALIBRATION s __p_c_LABORATORY _3 _94 !‘/ Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http:/www.chinattl.en Appendix (Additional assessments outside the scope of CNAS LO570) Antenna Parameters with Head TSL Impedance, transformed to feed point 50.80— 3.28j0 Return Loss — 29.50B Antenna Parameters with Body TSL Impedance, transformed to feed point 46.70— 3.98j0Q Return Loss — 25.50B General Antenna Parameters and Design Electrical Delay (one direction) 1.253 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z19—60082 Page 4 of 8

' 2 In Collaboration with m‘f~>p‘j, S_L_4 3 _9 ‘ CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.cn DASY5 Validation Report for Head TSL Date: 03.26.2019 Test Laboratory: CTTL, Beijing, China DUT : Dipole 835 MHz; Type: D835V2; Serial: D835V2 — SN: 4d151 Communication System: UID 0, CW; Frequency: 835 MHz; Duty Cycle: 1:1 Medium parameters used: f= 835 MHz; 0 = 0.925 S/m; s, = 42.68; p = 1000 kg/m3 Phantom section: Right Section DASY5 Configuration: e Probe: EX3DV4 — SN3617; ConvF(9.75, 9.75, 9.75) @ 835 MHz; Calibrated: 1/31/2019 e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAF4 Sn1331; Calibrated: 2/6/2019 e Phantom: MFP_V5.1C ; Type: QD 000 P51CA; Serial: 1062 e Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7450) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 57.34 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 3.55 W/kg SAR(1 g) =2.36 W/kg; SAR(10 g) = 1.56 W/kg Maximum value of SAR (measured) = 3.14 W/kg —1.99 —3.98 —5.98 —£.97 —9.96 0 dB = 3.14 W/kg = 4.97 dBW/kg Certificate No: Z19—60082 Page 5 of 8

® In Collaboration with mm\ a7J~7;J, @ CALIBRATION LABORATORY _ Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.en Impedance Measurement Plot for Head TSL Tri s11 Log Mag 10.00dB/ Ref 0.000ds [F1] *°—90 (<i~~g35, 00000 mnz —20.186 ds 40. 00 30. 00 20. 00 10. 00 0. 000 p| —10. 00 —20. 00 5 —30. 00 ~40. 00 —50. 00 s PWm s1i1 smith (R+]jX) scale 1.000U [F1 Del] »L 835.00000 MHz 50.823 o —3.2828 o 58.06 _ / 4 ~——__| Sn onl 1 Start 635 MHz IFBW 100 Hz Stop 1.035 gHz Me@i||© Certificate No: Z19—60082 Page 6 of 8

' # In Collaboration with =7/‘"7°J, S_P C 3 _9 v CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.en DASY5 Validation Report for Body TSL Date: 03.26.2019 Test Laboratory: CTTL, Beijing, China DUT : Dipole 835 MHz; Type: D835V2; Serial: D835V2 — SN: 4d151 Communication System: UID 0, CW; Frequency: 835 MHz; Duty Cycle: 1:1 Medium parameters used: f= 835 MHz; 0 = 0.944 S/m; s, = 56.66; p = 1000 kg/m3 Phantom section: Center Section DASY5 Configuration: e Probe: EX3DV4 — SN3617; ConvF(9.61, 9.61, 9.61) @ 835 MHz; Calibrated: 1/31/2019 e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAFE4 Sn1331; Calibrated: 2/6/2019 e Phantom: MFP_V5.1C ; Type: QD 000 P51CA; Serial: 1062 e Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7450) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 56.03 V/m; Power Drift = 0.04 dB Peak SAR (extrapolated) =3.53 W/kg SAR(1 g) =2.32 W/kg; SAR(10 g) = 1.52 W/kg Maximum value of SAR (measured) =3.12 W/kg —2.04 —4.08 —6.13 —8.1 7 —10.21 0 dB = 3.12 W/kg = 4.94 dBW/kg Certificate No: Z19—60082 Page 7 of 8

‘!!!!lllllllll....~;w In Collaboration with TTIL, _@ ‘ CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://www.chinattl.cn Impedance Measurement Plot for Body TSL Tri S11 Log Mag 10.00dB/ Ref 0.000d8 [F1] 50. 00 »L 835.00000 MHz —25.477 ds 40. 00 30. 00 20. 00 10. 00 0. 000 p) k —10. 00 —20.00 —30.00 —40,. 00 —50. 00 k PM si1 smith (R+jX) scale 1.000U [F1 Ddel] &XA P »1 835.00000 MHz 46.724 o —3.9773 n 47.923—pF_ * * f_D y3 1 Start 635 MHz \_ \.,._T_.d—f"( IFBW 100 Hz Stop 1.035 GHz DG@ll Certificate No: Z19—60082 Page 8 of 8

* In Collaboration with ‘\“\U" HEYAT @777 s_p___e_a_.q_4 § :; M AREW causntion Add: No.51 Xueyuan Road, Haidian tasonsrony District, Beijing, 100191, China CNAS#: 3" v cALIBRATION Tel: +86—10—62304633—2079 +86—10—62304633—2504 ,,h‘ CNAS LO570 E—mail: ettl@chinattl.com hutp://www.chinattl.en Client Sporton Certificate No: 219—60084 CALIBRATION CERTIFICATE Object D1750V2 — SN: 1090 Calibration Procedure(s) FF—Z211—003—01 Calibration Procedures for dipole validation kits Calibration date: March 27, 2019 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(22+3)‘C and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRP2 106277 20—Aug—18 (CTTL, No.J18X06862) Aug—19 Power sensor NRPBS 104291 20—Aug—18 (CTTL, No.J18X06862) Aug—19 Reference Probe EX3DV4 SN 3617 31—Jan—19(SPEAG,No.EX3—3617_Jan19) Jan—20 DAE4 SN 1331 06—Feb—19(SPEAG,No.DAE4—1331_Feb19) Feb—20 Secondary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Signal Generator E4438C MY49071430 23—Jan—19 (CTTL, No.J19X00336) Jan—20 NetworkAnalyzer E5071C MY46110673 24—Jan—19 (CTTL, No.J19X00547) Jan—20 Name Function Signature Calibrated by: Zhao Jing SAR Test Engineer fi#] Reviewed by: Lin Hao SAR Test Engineer IF(F% Approved by: Qi Dianyuan SAR Project Leader M/ Issued: March 29, 2019 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: Z19—60084 Page 1 of 8

!\* In Collaboration with -‘ 4. TTZL CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinatt.com hitps//www.chinattl.n Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORMx,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for assessmentof specific absorption rate of human exposure to radio frequency fields from hand—held and body—mounted wireless communication devices— Part 1: Device used next to the ear (Frequency range of 300MHz to 6GHz)", July 2016 c) IEC 62209—2, "Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices used in close proximity to the human body (frequency range of 30MHz to 6GHz)", March 2010 d) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. «_ Antenna Parameters with TSL: The dipole is mounted with the spacerto position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. & SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. Certificate No: Z19—60084 Page 2 of 8

§77Tr p_e_a in Collaboration with CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com hitp://www.chinattl.en Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY52 52.10.2.1495 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom 5.1C Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz = 5 mm Frequency 1750 MHz & 1 MHz Head TSL parameters Thefollowing parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 40.1 1.37 mho/m Measured Head TSL parameters (22.0 £ 0.2) °C 41.3 46 % 1.37 mho/m + 6 % Head TSL temperature change during test <1.0 °C —— —— SAR result with Head TSL SAR averaged over 1 cm (1 g) of Head TSL Condition SAR measured 250 mW input power 9.04 Wikg SAR for nominal Head TSL parameters normalized to 1W 36.4 Wikg £ 18.8 % (k=2) SAR averaged over 10 cm‘ (10 g) of Head TSL Condition SAR measured 250 mW input power 4.79 Wikg SAR for nominal Head TSL parameters normalized to 1W 19.2 Wikg £ 18.7 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 53.4 1.49 mho/m Measured Body TSL parameters (22.0 £0.2) °C 55.0 46 % 1.45 mho/m + 6 % Body TSL temperature change during test <1.0 °C —— —— SAR result with Body TSL SAR averaged over 1 cm> (1 g) of Body TSL Condition SAR measured 250 mW input power 9.21 Wikg SAR for nominal Body TSL parameters normalized to 1W 37.7 Wikg * 18.8 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL Condition SAR measured 250 mW input power 4.89 Wikg SAR for nominal Body TSL parameters normalized to 1W 19.9 Wikg * 18.7 % (k=2) Certificate No: Z19—60084 Page 3 of8

* In Collaboration with a TTIL CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinatt.com hitp://www.chinattl.en Appendix (Additional assessments outside the scope of CNAS LO570) Antenna Parameters with Head TSL Impedance, transformed to feed point 47.50— 2.34 jQ Return Loss —29.2 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 43.90—2.19 jQ Return Loss —23.2 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.085 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductorof the feeding line is directly connected to the second arm of the dipole. The antennais therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z19—60084 Page 4 of 8

aeffiiite© in Colleborstion vith a=‘/"/"J, a CALIBRATION LABORATORY rgar" Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com hitp:/www.chinattl.en DASYS5 Validation Report for Head TSL Date: 03.26.2019 Test Laboratory: CTTL, Beijing, China DUT: Dipole 1750 MHz; Type: D1750V2; Serial: D1750V2 — SN: 1090 Communication System: UID 0, CW; Frequency: 1750 MHz; Duty Cycle: 1:1 Medium parameters used: {= 1750 MHz; 0 = 1.37 $/m; &, = 41.27; p = 1000 kg/m3 Phantom section: Right Section DASY5 Configuration: * Probe: EX3DV4 — SN3617; ConvF(8.38, 8.38, 8.38) @ 1750 MHz; Calibrated: 1/31/2019 *« Sensor—Surface; 1.4mm (Mechanical Surface Detection) «+ Electronics: DAE4 Sn1331; Calibrated: 2/6/2019 «_ Phantom: MFP_V5.1C ; Type: QD 000 PS1CA; Serial: 1062 *« Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.12 (7450) System Performance Check/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=Smm, dy=5mm, dz=5mm Reference Value = $9.03 V/m; Power Drift = 0.03 dB Peak SAR (extrapolated) = 17.1 W/kg SAR(I g) = 9.04 W/kg; SAR(10 g) = 4.79 W/kg Maximum value of SAR (measured) = 14.2 W/kg dB 0 —3.36 —6.72 —10.07 13.43 —16.79 0 dB = 14.2 W/kg = 11.52 dBW/kg Certificate No: 719—60084 Page 5 of8

h“ In Collaboration with =TTLs_m_q_ Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinatt.com hitp://www.chinattl.en Impedance Measurement Plot for Head TSL Trisin l og Mag 10.00dB/ Ref 0.000d8 [F1] 50. 00 »11.7500000 anz ~20.158 da 40. 00 30.00 20.00 10. 00 0.00p) —10.00 ~20.00 ~30.00 ~40. 00 ~50.00 x BM 511 smith (ReJX) scale 1.0000 [F1 bel] »1. 1.7500000 ahz 47. 534 n —2.3303 o y/vr/—\ 1 Surt L5 GHe Stop 1195 Giic IRl Certificate No: Z19—60084 Page 6 of 8


Document Created: 2019-05-30 11:58:43
Document Modified: 2019-05-30 11:58:43
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC