Test Report PCE CDMA BC10

FCC ID: IHDT56XS2

Test Report

Download: PDF
FCCID_4190710

FCC RF Test Report Report No. : FW8D2801A FCC RF Test Report APPLICANT : Motorola Mobility LLC EQUIPMENT : Mobile Cellular Phone BRAND NAME : Motorola MODEL NAME : XT1980-3 FCC ID : IHDT56XS2 STANDARD : 47 CFR Part 2, and 90(S) CLASSIFICATION : PCS Licensed Transmitter Held to Ear (PCE) The product was received on Dec. 28, 2018 and completely tested on Feb. 14, 2019. We, Sporton International (Kunshan) Inc., would like to declare that the tested sample has been evaluated in accordance with the procedures given in ANSI C63.26-2015 and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of Sporton International (Kunshan) Inc., the test report shall not be reproduced except in full. Approved by: James Huang / Manager Sporton International (Kunshan) Inc. No. 1098, Pengxi North Road, Kunshan Economic Development Zone, Jiangsu Province 215335, China Sporton International (Kunshan) Inc. Page Number : 1 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A TABLE OF CONTENTS REVISION HISTORY.......................................................................................................................................... 3 SUMMARY OF TEST RESULT ......................................................................................................................... 4 1 GENERAL DESCRIPTION .......................................................................................................................... 5 1.1 Applicant ............................................................................................................................................ 5 1.2 Manufacturer ..................................................................................................................................... 5 1.3 Feature of Equipment Under Test ..................................................................................................... 5 1.4 Product Specification of Equipment Under Test ............................................................................... 5 1.5 Modification of EUT ........................................................................................................................... 6 1.6 Specification of Accessory ................................................................................................................ 6 1.7 Maximum Conducted Power, Frequency Tolerance and Emission Designator ................................ 6 1.8 Testing Site........................................................................................................................................ 7 1.9 Applied Standards ............................................................................................................................. 7 2 TEST CONFIGURATION OF EQUIPMENT UNDER TEST ........................................................................ 8 2.1 Test Mode.......................................................................................................................................... 8 2.2 Connection Diagram of Test System ................................................................................................ 9 2.3 Support Unit used in test configuration and system .......................................................................... 9 2.4 Measurement Results Explanation Example .................................................................................... 9 2.5 Frequency List of Low/Middle/High Channels ................................................................................. 10 3 TEST RESULT ........................................................................................................................................... 11 3.1 Conducted Output Power Measurement ......................................................................................... 11 3.2 99% Occupied Bandwidth and 26dB Bandwidth Measurement...................................................... 12 3.3 Emissions Mask Measurement ....................................................................................................... 13 3.4 Emissions Mask – Out Of Band Emissions Measurement .............................................................. 15 3.5 Field Strength of Spurious Radiation Measurement ....................................................................... 17 3.6 Frequency Stability Measurement ................................................................................................... 19 4 LIST OF MEASURING EQUIPMENT ........................................................................................................ 21 5 UNCERTAINTY OF EVALUATION ........................................................................................................... 22 APPENDIX A. TEST RESULTS OF CONDUCTED TEST APPENDIX B. TEST RESULTS OF RADIATED TEST APPENDIX C. SETUP PHOTOGRAPHS Sporton International (Kunshan) Inc. Page Number : 2 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A REVISION HISTORY REPORT NO. VERSION DESCRIPTION ISSUED DATE FW8D2801A Rev. 01 Initial issue of report Feb. 27, 2019 Sporton International (Kunshan) Inc. Page Number : 3 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A SUMMARY OF TEST RESULT Report FCC Rule Description Limit Result Remark Section 3.1 §2.1046 Conducted Output Power Reporting only PASS - §2.1049 Occupied Bandwidth and 3.2 Reporting only PASS - §90.209 26dB Bandwidth §2.1051 Emission masks – 3.3 < 50+10log10(P[Watts]) PASS - §90.691 In-band emissions §2.1051 Emission masks – 3.4 < 43+10log10(P[Watts]) PASS - §90.691 Out of band emissions Under limit §2.1053 Field Strength of Spurious 3.5 < 43+10log10(P[Watts]) PASS 32.25 dB at §90.691 Radiation 2460.000 MHz §2.1055 Frequency Stability for 3.6 < 2.5 ppm PASS - §90.213 Temperature & Voltage Sporton International (Kunshan) Inc. Page Number : 4 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 1 General Description 1.1 Applicant Motorola Mobility LLC 222 W,Merchandise Mart Plaza, Chicago IL 60654 USA 1.2 Manufacturer Motorola Mobility LLC 222 W,Merchandise Mart Plaza, Chicago IL 60654 USA 1.3 Feature of Equipment Under Test Product Feature & Specification Equipment Mobile Cellular Phone Brand Name Motorola Model Name XT1980-3 FCC ID IHDT56XS2 CDMA/EVDO/GSM/GPRS/EGPRS/WCDMA/HSPA/ DC-HSDPA/HSPA+(16QAM is not supported)/LTE WLAN 2.4GHz 802.11b/g/n HT20/HT40 EUT supports Radios application WLAN 5GHz 802.11a/n HT20/HT40 WLAN 5GHz 802.11ac VHT20/VHT40/VHT80 Bluetooth BR / EDR / LE NFC/GNSS/FM Receiver Conducted: 352156100008097 MEID Code Radiation: 352156100008246 HW Version DVT2 SW Version PPF29.58 EUT Stage Identical Prototype Remark: The above EUT's information was declared by manufacturer. Please refer to the specifications or user's manual for more detailed description. 1.4 Product Specification of Equipment Under Test Product Specification subjective to this standard Tx Frequency BC10 : 817.9 ~ 823.1 MHz Rx Frequency BC10 : 862.9 ~ 868.1 MHz Maximum Output Power to Antenna 25.29 dBm Antenna Type Dipole Antenna CDMA2000 1xRTT : QPSK Type of Modulation CDMA2000 1xEV-DO : QPSK/8PSK Sporton International (Kunshan) Inc. Page Number : 5 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

seomovc«s. FCC RF Test Report Report No. : FW8D2801A 1.5 Modification of EUT No modifications are made to the EUT during all test items. 1.6 Specification of Accessory Specification of Accessory [AC Adapter 1(US) B rand N Name Mo otorola I (Salom) I Model Name —51 |SC—5 Power Rating VP: 100—240 Vac, 0.6A O/P: 5Vdc,3A or 9Vdc,2A or 12Vdc,1.5A [AC Adapter 2(US) Brand Nan_re Motorola (Chenyang) |Mode| Name [SC—51 Power Rating VP: 100—240 Vac, 0.6A O/P: 5Vdc,3A or 9Vdc,2A or 12Vdc,1.5A Batt Brand Name Amperex (Motorola) Model Name |KZ40 atter Y Power Rating 3.8Vdc,3600mAh Type Li—ion Polymer Brand Name Motorola (Cabletech) Model Name |SC18C49697 USB Cable 1 — — — — — Signal Line Type|1.0 meter, shielded cable, without ferrite core Brand Name |Motorola (Saibao) |Model Name [SC18C24367 USB Cable 2 ~ — — — — Signal Line Type|1.0 meter, shielded cable, without ferrite core Brand Name ____|Motorola (Luxshare) |Model Name [SC18C24368 USB Cable 3 Signal Line Type 1.0 meter, shielded cable, without ferrite core 1.7 Maximum Conducted Power, Frequency Tolerance and Emission Designator T ¢ Frequency Emissi Maximum e0 mission FCC Rule System vP . Tolerance . ces Modulation (Ppm) Designator power(W) Part 908 CDMA2000 BC10 1xRTT QPSK 0.0280 ppm 1M27FIW 0.3381 Sporton International (Kunshan) Inc. Page Number : 6 of 22 TEL : 86—512—57900158 Report Issued Date : Feb. 27, 2019 FAX : 86—512—57900958 Report Version : Rev. 01 FCC ID : IHDTSGXS2 Report Template No.: BUS—FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 1.8 Testing Site Sporton International (Kunshan) Inc. is accredited to ISO 17025 by National Voluntary Laboratory Accreditation Program (NVLAP code: 600155-0). Test Site Sporton International (Kunshan) Inc. No. 1098, Pengxi North Road, Kunshan Economic Development Zone, Jiangsu Province 215335, China Test Site Location TEL : 86-512-57900158 FAX : 86-512-57900958 Sporton Site No. FCC designation No. FCC Test Firm Registration No. Test Site No. TH01-KS CN5013 630927 03CH06-KS 1.9 Applied Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards:  47 CFR Part 2, 90(S)  ANSI C63.26-2015  FCC KDB 971168 D01 Power Meas. License Digital Systems v03r01 Remark: 1. All test items were verified and recorded according to the standards and without any deviation during the test. 2. This EUT has also been tested and complied with the requirements of FCC Part 15, Subpart B, recorded in a separate test report. Sporton International (Kunshan) Inc. Page Number : 7 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 2 Test Configuration of Equipment Under Test 2.1 Test Mode During all testing, EUT is in link mode with base station emulator at maximum power level. The spurious emission measurements were carried out in semi-anechoic chamber with 3-meter test range, and EUT is rotated on three test planes to find out the worst emission. Frequency range investigated for radiated emission is 30 MHz to 10th harmonic. Test Modes Band Radiated TCs Conducted TCs CDMA2000 BC10  1xRTT Link  1xRTT Link Note: The maximum RF output power levels are 1xRTT RC1 SO55 mode for CDMA2000 BC10 on QPSK Link; only these modes were used for all tests. Sporton International (Kunshan) Inc. Page Number : 8 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 2.2 Connection Diagram of Test System System BT AP router Notebook GPS Station Simulator Earphone Power EUT Notebook Source Cradle Earphone iPod WLAN AP Monitor This example is connection diagram of EUT test configurations. . For detail, please refer to test mode configuration and setup photographs for each test item. 2.3 Support Unit used in test configuration and system Item Equipment Trade Name Model No. FCC ID Data Cable Power Cord 1. System Simulator R&S CMU 200 N/A N/A Unshielded, 1.8 m 2. DC Power Supply GW INSTEK GPS-3030D N/A N/A Unshielded, 1.8 m 3. Earphone Lenovo SH100 N/A Unshielded,1.2m N/A 2.4 Measurement Results Explanation Example For all conducted test items: The offset level is set in the spectrum analyzer to compensate the RF cable loss and attenuator factor between EUT conducted output port and spectrum analyzer. With the offset compensation, the spectrum analyzer reading level is exactly the EUT RF output level. Example: The spectrum analyzer offset is derived from RF cable loss and attenuator factor. Offset = RF cable loss + attenuator factor. Following shows an offset computation example with cable loss 4.5 dB and 10dB attenuator. Offset (dB) = RF cable loss (dB) + attenuator factor (dB). = 4.5 + 10 = 14.5 (dB) Sporton International (Kunshan) Inc. Page Number : 9 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 2.5 Frequency List of Low/Middle/High Channels Frequency List Band Channel/Frequency(MHz) Lowest Middle Highest CDMA200 Channel 476 580 684 BC10 Frequency 817.9 820.5 823.1 Sporton International (Kunshan) Inc. Page Number : 10 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 3 Test Result 3.1 Conducted Output Power Measurement 3.1.1 Description of the Conducted Output Power Measurement A system simulator was used to establish communication with the EUT. Its parameters were set to enforce EUT transmitting at the maximum power. The measured power in the radio frequency on the transmitter output terminals shall be reported. 3.1.2 Measuring Instruments The measuring equipment is listed in the section 4 of this test report. 3.1.3 Test Procedures 1. The transmitter output port was connected to the system simulator. 2. Set EUT at maximum power through system simulator. 3. Select lowest, middle, and highest channels for each band and different modulation. 4. Measure and record the power level from the system simulator. 3.1.4 Test Setup 3.1.5 Test Result of Conducted Output Power Please refer to Appendix A. Sporton International (Kunshan) Inc. Page Number : 11 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 3.2 99% Occupied Bandwidth and 26dB Bandwidth Measurement 3.2.1 Description of (Occupied) Bandwidth Limitations Measurement The 99% occupied bandwidth is the width of a frequency band such that, below the lower and above the upper frequency limits, the mean powers emitted are each equal to a specified percentage 0.5% of the total mean transmitted power. The emission bandwidth is defined as the width of the signal between two points, located at the 2 sides of the carrier frequency, outside of which all emissions are attenuated at least 26 dB below the transmitter power. 3.2.2 Measuring Instruments The measuring equipment is listed in the section 4 of this test report. 3.2.3 Test Procedures 1. The EUT was connected to spectrum analyzer and system simulator via a power divider. 2. The 26dB and 99% occupied bandwidth (BW) of the middle channel for the highest RF power with full RB sizes were measured. 3.2.4 Test Setup 3.2.5 Test Result of 99% Occupied Bandwidth and 26dB Bandwidth Please refer to Appendix A. Sporton International (Kunshan) Inc. Page Number : 12 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 3.3 Emissions Mask Measurement 3.3.1 Description of Emissions Mask Measurement Equipment used in this licensed to EA or non-EA systems shall comply with the emission mask provisions of FCC Part 90.691.(a): (a) Out-of-band emission requirement shall apply only to the “outer” channels included in an EA license and to spectrum adjacent to interior channels used by incumbent licensees. The emission limits are as follows: (1) For any frequency removed from the EA licensee's frequency block by up to and including 37.5 kHz, the power of any emission shall be attenuated below the transmitter power (P) in watts by at least 116 Log10(f/6.1) decibels or 50 + 10 Log10(P) decibels or 80 decibels, whichever is the lesser attenuation, where f is the frequency removed from the center of the outer channel in the block in kilohertz and where f is greater than 12.5 kHz. (2) For any frequency removed from the EA licensee's frequency block greater than 37.5 kHz, the power of any emission shall be attenuated below the transmitter power (P) in watts by at least 43 + 10Log 10(P) decibels or 80 decibels, whichever is the lesser attenuation, where f is the frequency removed from the center of the outer channel in the block in kilohertz and where f is greater than 37.5 kHz. 3.3.2 Measuring Instruments The measuring equipment is listed in the section 4 of this test report. 3.3.3 Test Procedures 1. The EUT was connected to spectrum analyzer and base station via power divider. 2. The emissions mask of low and high channels for the highest RF powers were measured. 3. The measured RBW and the VBW set 3 times of RBW are then set in spectrum analyzer, and the RBW correction factor 10log (1% of OBW/measured RBW)(dB) was compensated, if required. 4. The test results were shown below plots with a correction offset factor including cable loss, insertion loss of power divider. Sporton International (Kunshan) Inc. Page Number : 13 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 3.3.4 Test Setup 3.3.5 Test Result (Plots) of Conducted Emissions Mask Please refer to Appendix A. Sporton International (Kunshan) Inc. Page Number : 14 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 3.4 Emissions Mask – Out Of Band Emissions Measurement 3.4.1 Description of Conducted Emissions Out of band emissions measurement The power of any emission FCC Part 90.691 (a)(2) on any frequency removed from the assigned frequency by out of the authorized bandwidth at least 43 + 10 log (P) dB. It is measured by means of a th calibrated spectrum analyzer and scanned from 30 MHz up to a frequency including its 10 harmonic. 3.4.2 Measuring Instruments The measuring equipment is listed in the section 4 of this test report. 3.4.3 Test Procedures 1. The EUT was connected to spectrum analyzer and system simulator via a power divider. 2. The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator. The path loss was compensated to the results for each measurement. 3. The middle channel for the highest RF power within the transmitting frequency was measured. 4. The conducted spurious emission for the whole frequency range was taken. 5. Make the measurement with the spectrum analyzer's RBW = 1MHz, VBW = 3MHz, taking the record of maximum spurious emission. 6. The RF fundamental frequency should be excluded against the limit line in the operating frequency band. 7. The limit line is derived from 43 + 10log(P)dB below the transmitter power P(Watts) = P(W)- [43 + 10log(P)] (dB) = [30 + 10log(P)] (dBm) - [43 + 10log(P)] (dB) = -13dBm. Sporton International (Kunshan) Inc. Page Number : 15 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 3.4.4 Test Setup 3.4.5 Test Result (Plots) of Conducted Emission Please refer to Appendix A. Sporton International (Kunshan) Inc. Page Number : 16 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 3.5 Field Strength of Spurious Radiation Measurement 3.5.1 Description of Field Strength of Spurious Radiated Measurement The radiated spurious emission was measured by substitution method according to ANSI C63.26. The power of any emission FCC Part 90.691 on any frequency removed from the assigned frequency by more than 250 percent of the authorized bandwidth at least 43 + 10 log (P) dB. The spectrum is scanned from 30 MHz up to a frequency including its 10th harmonic. 3.5.2 Measuring Instruments The measuring equipment is listed in the section 4 of this test report. 3.5.3 Test Procedures 1. The EUT was placed on a turntable with 0.8 meter for frequency below 1GHz and 1.5 meter for frequency above 1GHz respectively above ground. 2. The EUT was set 3 meters from the receiving antenna, which was mounted on the antenna tower. 3. The table was rotated 360 degrees to determine the position of the highest spurious emission. 4. The height of the receiving antenna is varied between one meter and four meters to search the maximum spurious emission for both horizontal and vertical polarizations. 5. Make the measurement with the spectrum analyzer's RBW = 1MHz, VBW = 3MHz, Sweep = 500ms, Taking the record of maximum spurious emission. 6. A horn antenna was substituted in place of the EUT and was driven by a signal generator. 7. Tune the output power of signal generator to the same emission level with EUT maximum spurious emission. 8. Taking the record of output power at antenna port. 9. Repeat step 7 to step 8 for another polarization. 10. EIRP (dBm) = S.G. Power – Tx Cable Loss + Tx Antenna Gain 11. ERP (dBm) = EIRP - 2.15 12. The RF fundamental frequency should be excluded against the limit line in the operating frequency band. 13. The limit line is derived from 43 + 10log(P) dB below the transmitter power P(Watts) Sporton International (Kunshan) Inc. Page Number : 17 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 3.5.4 Test Setup For radiated test from 30MHz to 1GHz For radiated test above 1GHz 3.5.5 Test Result of Field Strength of Spurious Radiated Please refer to Appendix B. Sporton International (Kunshan) Inc. Page Number : 18 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 3.6 Frequency Stability Measurement 3.6.1 Description of Frequency Stability Measurement The frequency stability shall be measured by variation of ambient temperature and variation of primary supply voltage to ensure that the fundamental emission stays within the authorized frequency block. The frequency stability of the transmitter shall be maintained within ±0.00025% (±2.5ppm) of the center frequency according to FCC Part 90.213. 3.6.2 Measuring Instruments The measuring equipment is listed in the section 4 of this test report. 3.6.3 Test Procedures for Temperature Variation 1. The EUT was set up in the thermal chamber and connected with the base station. 2. With power OFF, the temperature was decreased to -30°C and the EUT was stabilized for three hours. Power was applied and the maximum change in frequency was recorded within one minute. 3. With power OFF, the temperature was raised in 10°C step up to 50°C. The EUT was stabilized at each step for at least half an hour. Power was applied and the maximum frequency change was recorded within one minute. 3.6.4 Test Procedures for Voltage Variation 1. The EUT was placed in a temperature chamber at 20±5°C and connected with the system simulator. 2. The power supply voltage to the EUT was varied from 85% to 115% of the nominal value for other than hand carried battery equipment. 3. For hand carried, battery powered equipment, reduce the primary ac or dc supply voltage to the 4. battery operating end point, which shall be specified by the manufacturer. 5. The variation in frequency was measured for the worst case. Sporton International (Kunshan) Inc. Page Number : 19 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 3.6.5 Test Setup 3.6.6 Test Result of Temperature Variation Please refer to Appendix A. Sporton International (Kunshan) Inc. Page Number : 20 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 4 List of Measuring Equipment Calibration Instrument Manufacturer Model No. Serial No. Characteristics Test Date Due Date Remark Date Spectrum Conducted R&S FSV40 101040 10Hz~40GHz Aug. 07, 2018 Feb. 14, 2019 Aug. 06, 2019 Analyzer (TH01-KS) Thermal -40~+150°C Conducted Hongzhan LP-150U H2014011440 Jun. 27, 2018 Feb. 14, 2019 Jun. 26, 2019 Chamber 20%~95%RH (TH01-KS) EXA Spectrum Radiation Keysight N9010B MY57471084 10Hz-44GHz Jun. 25, 2018 Jan. 18, 2019 Jun. 24, 2019 Analyzer (03CH06-KS) Radiation Bilog Antenna TeseQ CBL6111D 44483 30MHz-1GHz Jan. 29, 2018 Jan. 18, 2019 Jan. 28, 2019 (03CH06-KS) Double Ridge Radiation ETS-Lindgren 3117 75957 1GHz~18GHz Oct. 20, 2018 Jan. 18, 2019 Oct. 19, 2019 Horn Antenna (03CH06-KS) Radiation SHF-EHF Horn Schwarzbeck BBHA 9170 BBHA170249 15GHz~40GHz Feb. 07, 2018 Jan. 18, 2019 Feb. 06, 2019 (03CH06-KS) Radiation Amplifier SONOMA 310N 187289 9KHz ~1GHZ Aug. 06, 2018 Jan. 18, 2019 Aug. 05, 2019 (03CH06-KS) TTA1840-35 Radiation Amplifier MITEQ 2014749 18~40GHz Feb. 08, 2018 Jan. 18, 2019 Feb. 07, 2019 -HG (03CH06-KS) high gain AMF-7D-00 Radiation MITEQ 101800-30-1 2025788 1Ghz-18Ghz Apr. 17, 2018 Jan. 18, 2019 Apr. 16, 2019 Amplifier (03CH06-KS) 0P Radiation Amplifier Keysight 83017A MY53270203 500MHz~26.5GHz Apr. 18, 2018 Jan. 18, 2019 Apr. 17, 2019 (03CH06-KS) AC Power Radiation Chroma 61601 F104090004 N/A NCR Jan. 18, 2019 NCR Source (03CH06-KS) Radiation Turn Table ChamPro EM 1000-T 060762-T 0~360 degree NCR Jan. 18, 2019 NCR (03CH06-KS) Radiation Antenna Mast ChamPro EM 1000-A 060762-A 1 m~4 m NCR Jan. 18, 2019 NCR (03CH06-KS) NCR: No Calibration Required Sporton International (Kunshan) Inc. Page Number : 21 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A 5 Uncertainty of Evaluation The measurement uncertainties shown below were calculated in accordance with the requirements of ANSI 63.26-2015. All the measurement uncertainty value were shown with a coverage K=2 to indicate 95% level of confidence. The measurement data show herein meets or exceeds the CISPR measurement uncertainty values specified in CISPR 16-4-2 and can be compared directly to specified limit to determine compliance. Uncertainty of Radiated Emission Measurement (30 MHz ~ 1000 MHz) Measuring Uncertainty for a Level of 2.5 dB Confidence of 95% (U = 2Uc(y)) Uncertainty of Radiated Emission Measurement (1GHz ~ 18GHz) Measuring Uncertainty for a Level of 2.0 dB Confidence of 95% (U = 2Uc(y)) Sporton International (Kunshan) Inc. Page Number : 22 of 22 TEL : 86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : 86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2 Report Template No.: BU5-FWCDMA Version 2.0

FCC RF Test Report Report No. : FW8D2801A Appendix A. Test Results of Conducted Test Conducted Output Power (Average power) Conducted Power (*Unit: dBm) Band CDMA2000 BC10 Channel 476 580 684 Frequency 817.9 820.5 823.1 1xRTT RC1 SO55 25.29 25.25 25.22 1xRTT RC3 SO55 25.23 25.22 25.18 1xRTT RC3 SO32(+ F-SCH) 25.24 25.21 25.15 1xRTT RC3 SO32 (+SCH) 25.23 25.21 25.19 1xEVDO RTAP 153.6Kbps 25.23 25.20 25.17 1xEVDO RETAP 4096Bits 25.23 25.21 25.18 Sporton International (Kunshan) Inc. Page Number : A1 of A8 TEL : +86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2

FCC RF Test Report Report No. : FW8D2801A 26dB Bandwidth Mode CDMA BC10(MHz) Mod. 1xRTT Lowest CH 1.4346 Middle CH 1.4306 Highest CH 1.4286 Sporton International (Kunshan) Inc. Page Number : A2 of A8 TEL : +86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2

FCC RF Test Report Report No. : FW8D2801A CDMA BC10 (1xRTT) Lowest Channel Middle Channel Highest Channel Sporton International (Kunshan) Inc. Page Number : A3 of A8 TEL : +86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2

FCC RF Test Report Report No. : FW8D2801A Occupied Bandwidth Mode CDMA BC10(MHz) Mod. 1xRTT Lowest CH 1.27 Middle CH 1.27 Highest CH 1.27 Sporton International (Kunshan) Inc. Page Number : A4 of A8 TEL : +86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2

FCC RF Test Report Report No. : FW8D2801A CDMA BC10 (1xRTT) Lowest Channel Middle Channel Highest Channel Sporton International (Kunshan) Inc. Page Number : A5 of A8 TEL : +86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2

FCC RF Test Report Report No. : FW8D2801A Conducted Band Edge CDMA BC10 (1xRTT) Lowest Band Edge Highest Band Edge Sporton International (Kunshan) Inc. Page Number : A6 of A8 TEL : +86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2

FCC RF Test Report Report No. : FW8D2801A Conducted Spurious Emission CDMA BC10 (1xRTT) Lowest Channel Middle Channel Highest Channel Sporton International (Kunshan) Inc. Page Number : A7 of A8 TEL : +86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2

FCC RF Test Report Report No. : FW8D2801A Frequency Stability CDMA BC10 Limit Test Conditions Middle Channel (1xRTT) 2.5ppm Temperature (°C) Voltage (Volt) Deviation (ppm) Result 50 Normal Voltage 0.0183 40 Normal Voltage 0.0073 30 Normal Voltage 0.0280 20(Ref.) Normal Voltage 0.0000 10 Normal Voltage 0.0024 0 Normal Voltage 0.0049 PASS -10 Normal Voltage 0.0061 -20 Normal Voltage 0.0171 -30 Normal Voltage 0.0085 20 Maximum Voltage 0.0232 20 Normal Voltage 0.0000 20 Battery End Point 0.0037 Note: Normal Voltage = 3.8V；Battery End Point (BEP) = 3.6V；Maximum Voltage =4.4V Sporton International (Kunshan) Inc. Page Number : A8 of A8 TEL : +86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2

FCC RF Test Report Report No. : FW8D2801A Appendix B. Test Results of Radiated Test CDMA BC10 (1xRTT) Over S.G. TX Cable TX Antenna Frequency ERP Limit Polarization Channel Limit Power loss Gain ( MHz ) ( dBm ) ( dBm ) (H/V) ( dB ) ( dBm ) ( dB ) (dBi) 1636 -68.67 -13 -55.67 -69.88 2.32 5.68 H 2454 -56.76 -13 -43.76 -57.39 3.02 5.80 H 3270 -64.59 -13 -51.59 -67.05 3.27 7.88 H Lowest 1636 -68.69 -13 -55.69 -69.90 2.32 5.68 V 2454 -62.44 -13 -49.44 -63.07 3.02 5.80 V 3270 -64.84 -13 -51.84 -67.30 3.27 7.88 V 1641 -67.39 -13 -54.39 -68.60 2.32 5.68 H 2460 -45.25 -13 -32.25 -45.88 3.02 5.80 H 3282 -64.64 -13 -51.64 -67.10 3.27 7.88 H Middle 1640 -67.04 -13 -54.04 -68.25 2.32 5.68 V 2460 -54.11 -13 -41.11 -54.74 3.02 5.80 V 3282 -64.65 -13 -51.65 -67.11 3.27 7.88 V 1646 -67.75 -13 -54.75 -68.96 2.32 5.68 H 2470 -52.83 -13 -39.83 -53.46 3.02 5.80 H 3294 -64.79 -13 -51.79 -67.25 3.27 7.88 H Highest 1646 -68.42 -13 -55.42 -69.63 2.32 5.68 V 2470 -58.24 -13 -45.24 -58.87 3.02 5.80 V 3294 -64.90 -13 -51.90 -67.36 3.27 7.88 V Remark: Spurious emissions within 30-1000MHz were found more than 20dB below limit line. Sporton International (Kunshan) Inc. Page Number : B1 of B1 TEL : +86-512-57900158 Report Issued Date : Feb. 27, 2019 FAX : +86-512-57900958 Report Version : Rev. 01 FCC ID : IHDT56XS2


Document Created: 2019-03-25 11:08:44
Document Modified: 2019-03-25 11:08:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC