TestRpt_Power Density_Appendix C

FCC ID: IHDT56XL1

RF Exposure Info

Download: PDF
FCCID_4188348




Measurement Report for 30 GHz Verification Source, FRONT (SCREEN), Validation, UID 0 -, Channel 30000 (30000.0MHz) Device under Test Properties Name, Manufacturer Dimensions [mm] IMEI DUT Type , 30 GHz Verification Source 100.0 x 100.0 x 100.0 Bar/Brick Exposure Conditions Phantom Section Position, Test Distance Band Group, Frequency [MHz], Conversion Factor [mm] UID Channel Number 5G - FRONT (SCREEN), Validation CW, 30000.0, 1.0 5.55 mm 0-- 30000 Hardware Setup Phantom Medium Probe, Calibration Date DAE, Calibration Date 5G Phantom V0.1- xxxx Air --- EUmmWV2 - SN9374, 2018-03-23 DAE4 Sn1215, 2018-02-26 Scan Setup Measurement Results 5G Scan 5G Scan Grid Extents [mm] 60.0 x 60.0 x 2.5 Date 2018-04-06, 16:36 Grid Steps [mm] 2.5 x 2.5 Avg. Area [cm2] 1.00 Sensor Surface [mm] 5.55 Savg [W/m2] 39.8 MAIA MAIA not used Speak [W/m2] 54.8 Epeak [V/m] 133 Hpeak [A/m] 0.413 Power Drift [dB] -0.09 Warning(s) / Error(s) Details Area Scan Warning(s) Error(s)

Calibration Laboratory of Schmid & Partner s C Schweizerischer Kalibrierdienst Service suisse d'etalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recogn ition of calibration certificates Client Sporton Certificate No: DAE4-778_May18 CALIBRATION CERTIFICATE Object DAE4 - SD 000 D04 BM - SN: 778 Calibration procedure(s) QA CAL-06.v29 Calibration procedure for the data acquisition electronics (DAE) Calibration date: May 25, 2018 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (SI). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 ± 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards Cal Date (Certificate No.) Scheduled Calibration Keithley Multimeter Type 2001 I SN: 0810278 31-Aug-17 (No:21092) Aug-18 Secondary Standards ID # Check Date (in house) Scheduled Check Auto DAE Calibration Unit SE UWS 053 AA 1001 04-Jan-18 (in house check) In house check: Jan-19 Calibrator Box V2.1 SE UMS 006 AA 1002 04-Jan-18 (in house check) In house check: Jan-19 Name Function Signature Calibrated by: Dominique Steffen Laboratory Technician ~ 2 -. Approved by: Sven Kuhn Deputy Manager \ ,I , ~ l)}JLif 1 Issued: May 25, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: DAE4-778_May18 Page 1 of 5

Calibration Laboratory of S Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d'etalonnage C Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland s Swiss Calibration Service Accredited by the Swiss Accreditation SeNice (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for t he recognition of calibration certificates Glossary DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters • DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. • Connector angle: The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required . • The following parameters as documented in the Appendix contain technical information as a result from the performance test and require no uncertainty. • DC Voltage Measurement Linearity: Verification of the Linearity at + 10% and -10% of the nominal calibration voltage. Influence of offset voltage is included in this measurement. • Common mode sensitivity: Influence of a positive or negative common mode voltage on the differential measurement. • Channel separation: Influence of a voltage on the neighbor channels not subject to an input voltage. • AD Converter Values with inputs shorted: Values on the internal AD converter corresponding to zero input voltage • Input Offset Measurement Output voltage and statistical results over a large number of zero voltage measurements. • Input Offset Current: Typical value for information; Maximum channel input offset current, not considering the input resistance. • Input resistance: Typical value for information: DAE input resistance at the connector, during internal auto-zeroing and during measurement. • Low Battery Alarm Voltage: Typical value for information . Below this voltage, a battery alarm signal is generated. • Power consumption: Typical value for information. Supply currents in various operating modes. Certificate No: DAE4-778_May18 Page 2 of 5

DC Voltage Measurement AID - Converter Resolution nominal High Range: 1LSB; 6.1µV, full range; -100 ... +300 mV LowRange: 1LS8; 61nV, fullrange; -1 .......+3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors X y z High Range 404.721 ± 0.02% (k;2) 403.519 ± 0.02% (k;2) 405.076 ± 0.02% (k;2) Low Range 3.98715 ± 1.50% (k;2) 3.96471 ± 1.50% (k;2) 4.00070 ± 1.50% (k;2) Connector Angle Connector Angle to be used in DASY system 269.0 °±1 ° Certificate No: DAE4-778_May18 Page 3 of 5

Appendix (Additional assessments outside the scope of SCS0108) 1. DC Voltaae Linearitv High Range Reading (µV) Difference (µ V) Error(%) ChannelX + Input 199995.64 0.22 0.00 ChannelX + Input 20002.64 0.86 0.00 ChannelX - Input -19997.90 3.08 -0.02 Channel Y + Input 199995.52 0.45 0.00 Channel Y + Input 20001.45 -0.24 -0.00 ChannelY - Input -19999.33 1.69 -0.01 Channel Z + Input 199995.39 0.09 0.00 Channel Z + Input 19999.28 -2.37 -0.01 Channel Z - Input -20004.97 -3.83 0.02 Low Range Reading (µV) Difference (µV) Error(%) Channel X + Input 2001.37 0.09 0.00 Channel X + Input 201.71 0.03 0.02 ChannelX - Input -198.71 -0.55 0.28 Channel Y + Input 2002.06 0.78 0.04 ChannelY + Input 201.56 -0.13 -0.07 Channel Y - Input -198.85 -0.61 0.31 ChannelZ + Input 2001.83 0.60 0.03 ChannelZ + Input 200.63 -1.14 -0.57 ChannelZ - Input -199.30 -0.95 0.48 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 sec; Measurina time: 3 sec Common mode High Range Low Range Input Voltage (mV) Average Reading (µV) Average Reading (µV) Channel X 200 -4.34 -5.51 - 200 6.01 4.80 Channel Y 200 0.02 -1.10 - 200 0.55 0.11 ChannelZ 200 -13.81 -14.40 -200 12.18 11.59 3. Channel separation DASY measurement parameters: Auto Zero Time: 3 sec; Measurinn time: 3 sec Input Voltage (mV) Channel X (µV) Channel Y (µV) Channel Z (µV) ChannelX 200 - -0.84 -2.53 ChannelY 200 8.46 - 0.02 ChannelZ 200 4.29 6.73 - Certificate No: DAE4-778_May18 Page 4 of 5

4. AD-Converter Values with inputs shorted DASY measurement parameters: Auto Zero Time: 3 sec; Measurino time: 3 sec High Range (LSB) Low Range (LSB) ChannelX 16056 16906 Channel Y 16191 17602 Channel Z 16433 15344 5. Input Offset Measurement DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec lnout 10MQ Std. Deviation Average (µVJ min. Offset (µVJ max. Offset (µVJ (11Vl ChannelX -0.05 -1.10 1.05 0.43 ChannelY 0.23 -1.15 1.67 0.53 Channel Z -0.76 -1.76 0.94 0.52 6. Input Offset Current Nominal Input circuitry offset current on all channels: <25fA 7. In out Resistance /Tvpical values for information) Zeroing (kOhm) Measuring (MOhm) ChannelX 200 200 Channel Y 200 200 Channel Z 200 200 8. Low Batterv Alarm Voltaae (Tvpical values for information\ Typical values Alarm Level (VDC) Supply(+ Vee) +7.9 Supply (- Vee) -7.6 9. Power Consumotion (Typical values for information) Typical values Switched off (mA) Stand by (mA) Transmitting (mA) Supply(+ Vee) +0.01 +6 +14 Supply (- Vee) -0.01 -8 -9 Certificate No: DAE4-778_May18 Page 5 of 5







Document Created: 2019-03-24 11:05:29
Document Modified: 2019-03-24 11:05:29
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC