NBG4615-revise-0119-4

FCC ID: I88NBG4615

Test Report

Download: PDF
FCCID_1406731

FCC ID.: I88NBG4615 Report No.: TS10080165-EME 7. Radiated Spurious Emission Name of Test Radiated Spurious Emission Base Standard FCC 15.247(d), 15.209, 15.205 Test Result: Complies Measurement Data: See Tables below Method of Measurement: Reference FCC document: KDB558074, ANSI C63.4 The frequency range from 30 MHz to 1000 MHz using Bilog Antenna. The frequency range over 1 GHz using Horn Antenna. Radiated emissions were invested cover the frequency range from 30 MHz to 1000 MHz using a receiver RBW of 120 kHz record QP reading, and the frequency over 1 GHz using a spectrum analyzer RBW of 1 MHz and 10 Hz VBW record Average reading. (15.209 paragraph), the Peak reading (1 MHz RBW/VBW) recorded also on the report. The EUT for testing is arranged on a wooden turntable. If some peripherals apply to the EUT, the peripherals will be connected to EUT and the whole system. During the test, all cables were arranged to produce worst-case emissions. The signal is maximized through rotation. The height of antenna and polarization is changing constantly for exploring for maximum signal level. The height of antenna can be up to 4 meters and down to 1 meter. The measurement for radiated emission will be done at the distance of three meters unless the signal level is too low to measure at that distance. In the case of the reading under noise floor, a pre-amplifier is used and/or the test is conducted at a closer distance. And then all readings are extrapolated back to the equivalent 3 meters reading using inverse scaling with distance. The EUT configuration please refer to the “Spurious set-up photo.pdf”. Page 69 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Test Diagram: Antenna Tower Horn or Bilog 1-4 meter Antenna 3 meter HPF and Pre-Amp. EUT 0.8 m Ground Plane □ Peripheral RF Test Receiver Emission Limit: The spurious Emission shall test through the 10th harmonic. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a). Frequency Limits (MHz) (dBμV/m@ 3 meter) 30-88 40 88-216 43.5 216-960 46 Above 960 54 Remark: 1. In the above table, the tighter limit applies at the band edges. 2. Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system Page 70 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Measurement results: frequencies equal to or less than 1 GHz The test was performed on EUT under 802.11b, 802.11g and 802.11n continuously transmitting mode. Channel 1, 6, 11 were verified. The worst case occurred at 802.11b Tx channel 1. EUT : NBG4615 Worst Case : 802.11b Tx at channel 1 Polarization Frequency Detector Corr. Reading Calculated Limit Margin (circle) (MHz) Factor (dBuV) dBuV/m (dBuV/m) (dB) (dB/m) Vertical 74.62 QP 10.39 28.56 38.95 40.00 -1.05 Vertical 249.22 QP 12.22 23.16 35.37 46.00 -10.63 Vertical 374.35 QP 15.06 24.22 39.28 46.00 -6.72 Vertical 384.05 QP 16.40 24.54 40.94 46.00 -5.06 Vertical 624.61 QP 20.75 21.23 41.98 46.00 -4.02 Vertical 874.87 QP 23.70 20.07 43.77 46.00 -2.23 Horizontal 74.62 QP 11.29 21.38 32.66 40.00 -7.34 Horizontal 249.22 QP 12.36 30.75 43.11 46.00 -2.89 Horizontal 374.35 QP 15.48 22.68 38.15 46.00 -7.85 Horizontal 384.05 QP 16.74 24.93 41.67 46.00 -4.33 Horizontal 624.61 QP 20.88 24.27 45.14 46.00 -0.86 Horizontal 874.87 QP 24.12 20.81 44.92 46.00 -1.08 Horizontal 1000.00 QP 25.78 15.00 40.77 54.00 -13.23 Remark: 1. Corr. Factor = Antenna Factor + Cable Loss 2. Corrected Level = Reading + Corr. Factor Page 71 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Measurement results: frequency above 1GHz EUT : NBG4615 Test Condition : 802.11b Tx at channel 1 (DAC0) Frequency Spectrum Antenna Preamp. Correction Reading Corrected Limit Margin Analyzer Polariz. Gain Factor Level @3m (MHz) Detector (H/V) (dB) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) 3210.00 PK V 35.54 34.62 44.53 43.61 54 -10.39 4824.00 PK V 36.07 37.77 53.41 55.11 74 -18.89 4824.00 AV V 36.07 37.77 51.26 52.96 54 -1.04 4824.00 PK H 36.07 37.77 43.21 44.91 54 -9.09 Remark: 1. Correction Factor = Antenna Factor + Cable Loss 2. Corrected Level = Reading + Correction Factor – Preamp. Gain 3. The frequency measured ranges from 1GHz to 25GHz.The data value listed above which is higher than the system noise floor. EUT : NBG4615 Test Condition : 802.11b Tx at channel 6 (DAC0) Frequency Spectrum Antenna Preamp. Correction Reading Corrected Limit Margin Analyzer Polariz. Gain Factor Level @3m (MHz) Detector (H/V) (dB) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) 4874.00 PK V 36.07 37.77 52.90 54.60 74 -19.40 4874.00 AV V 36.07 37.77 50.92 52.62 54 -1.38 4874.00 PK H 36.07 37.77 42.21 43.91 54 -10.09 Remark: 1. Correction Factor = Antenna Factor + Cable Loss 2. Corrected Level = Reading + Correction Factor – Preamp. Gain 3. The frequency measured ranges from 1GHz to 25GHz.The data value listed above which is higher than the system noise floor. Page 72 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME EUT : NBG4615 Test Condition : 802.11b Tx at channel 11 (DAC0) Frequency Spectrum Antenna Preamp. Correction Reading Corrected Limit Margin Analyzer Polariz. Gain Factor Level @3m (MHz) Detector (H/V) (dB) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) 4924.00 PK V 36.07 37.77 46.75 48.45 54 -5.55 4924.00 PK H 36.07 37.77 40.62 42.32 54 -11.68 Remark: 1. Correction Factor = Antenna Factor + Cable Loss 2. Corrected Level = Reading + Correction Factor – Preamp. Gain 3. The frequency measured ranges from 1GHz to 25GHz.The data value listed above which is higher than the system noise floor. EUT : NBG4615 Test Condition : 802.11g Tx at channel 1 (DAC0) Frequency Spectrum Antenna Preamp. Correction Reading Corrected Limit Margin Analyzer Polariz. Gain Factor Level @3m (MHz) Detector (H/V) (dB) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) 4824.00 PK V 36.07 37.77 57.66 59.36 74 -14.64 4824.00 AV V 36.07 37.77 43.65 45.35 54 -8.65 4824.00 PK H 36.07 37.77 43.9 45.6 54 -8.40 Remark: 1. Correction Factor = Antenna Factor + Cable Loss 2. Corrected Level = Reading + Correction Factor – Preamp. Gain 3. The frequency measured ranges from 1GHz to 25GHz.The data value listed above which is higher than the system noise floor. Page 73 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME EUT : NBG4615 Test Condition : 802.11g Tx at channel 6 (DAC0) Frequency Spectrum Antenna Preamp. Correction Reading Corrected Limit Margin Analyzer Polariz. Gain Factor Level @3m (MHz) Detector (H/V) (dB) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) 4874.00 PK V 36.07 37.77 55.58 57.28 74 -16.72 4874.00 AV V 36.07 37.77 42.53 44.23 54 -9.77 4874.00 PK H 36.07 37.77 44.93 46.63 54 -7.37 Remark: 1. Correction Factor = Antenna Factor + Cable Loss 2. Corrected Level = Reading + Correction Factor – Preamp. Gain 3. The frequency measured ranges from 1GHz to 25GHz.The data value listed above which is higher than the system noise floor. EUT : NBG4615 Test Condition : 802.11g Tx at channel 11 (DAC0) Frequency Spectrum Antenna Preamp. Correction Reading Corrected Limit Margin Analyzer Polariz. Gain Factor Level @3m (MHz) Detector (H/V) (dB) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) 4924.00 PK V 36.07 37.77 49.62 51.32 54 -2.68 4924.00 PK H 36.07 37.77 40.37 42.07 54 -11.93 Remark: 1. Correction Factor = Antenna Factor + Cable Loss 2. Corrected Level = Reading + Correction Factor – Preamp. Gain 3. The frequency measured ranges from 1GHz to 25GHz.The data value listed above which is higher than the system noise floor. Page 74 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME EUT : NBG4615 Test Condition : 802.11g Tx at channel 1 (DAC1) Frequency Spectrum Antenna Preamp. Correction Reading Corrected Limit Margin Analyzer Polariz. Gain Factor Level @3m (MHz) Detector (H/V) (dB) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) 4824.00 PK V 36.07 37.77 40.62 42.32 54 -11.68 4824.00 PK H 36.07 37.77 38.58 40.28 54 -13.72 Remark: 1. Correction Factor = Antenna Factor + Cable Loss 2. Corrected Level = Reading + Correction Factor – Preamp. Gain 3. The frequency measured ranges from 1GHz to 25GHz.The data value listed above which is higher than the system noise floor. EUT : NBG4615 Test Condition : 802.11g Tx at channel 6 (DAC1) Frequency Spectrum Antenna Preamp. Correction Reading Corrected Limit Margin Analyzer Polariz. Gain Factor Level @3m (MHz) Detector (H/V) (dB) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) 4874.00 PK V 36.07 37.77 40.50 42.20 54 -11.80 4874.00 PK H 36.07 37.77 39.15 40.85 54 -13.15 Remark: 1. Correction Factor = Antenna Factor + Cable Loss 2. Corrected Level = Reading + Correction Factor – Preamp. Gain 3. The frequency measured ranges from 1GHz to 25GHz.The data value listed above which is higher than the system noise floor. Page 75 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME EUT : NBG4615 Test Condition : 802.11g Tx at channel 11 (DAC1) Frequency Spectrum Antenna Preamp. Correction Reading Corrected Limit Margin Analyzer Polariz. Gain Factor Level @3m (MHz) Detector (H/V) (dB) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) 4924.00 PK V 36.07 37.77 41.45 43.15 54 -10.85 4924.00 PK H 36.07 37.77 38.50 40.20 54 -13.80 Remark: 1. Correction Factor = Antenna Factor + Cable Loss 2. Corrected Level = Reading + Correction Factor – Preamp. Gain 3. The frequency measured ranges from 1GHz to 25GHz.The data value listed above which is higher than the system noise floor. EUT : NBG4615 Test Condition : 802.11n HT20 Tx at channel 1 (DAC0+DAC1) Frequency Spectrum Antenna Preamp. Correction Reading Corrected Limit Margin Analyzer Polariz. Gain Factor Level @3m (MHz) Detector (H/V) (dB) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) 4824.00 PK V 36.07 37.77 58.12 59.82 74 -14.18 4824.00 AV V 36.07 37.77 42.70 44.40 54 -9.60 4824.00 PK H 36.07 37.77 43.66 45.36 54 -8.64 Remark: 1. Correction Factor = Antenna Factor + Cable Loss 2. Corrected Level = Reading + Correction Factor – Preamp. Gain 3. The frequency measured ranges from 1GHz to 25GHz.The data value listed above which is higher than the system noise floor. Page 76 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME EUT : NBG4615 Test Condition : 802.11n HT20 Tx at channel 6 (DAC0+DAC1) Frequency Spectrum Antenna Preamp. Correction Reading Corrected Limit Margin Analyzer Polariz. Gain Factor Level @3m (MHz) Detector (H/V) (dB) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) 4874.00 PK V 36.07 37.77 56.16 57.86 74 -16.14 4874.00 AV V 36.07 37.77 41.55 43.25 54 -10.75 4874.00 PK H 36.07 37.77 45.44 47.14 54 -6.86 Remark: 1. Correction Factor = Antenna Factor + Cable Loss 2. Corrected Level = Reading + Correction Factor – Preamp. Gain 3. The frequency measured ranges from 1GHz to 25GHz.The data value listed above which is higher than the system noise floor. EUT : NBG4615 Test Condition : 802.11n HT20 Tx at channel 11 (DAC0+DAC1) Frequency Spectrum Antenna Preamp. Correction Reading Corrected Limit Margin Analyzer Polariz. Gain Factor Level @3m (MHz) Detector (H/V) (dB) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) 3270.00 PK V 35.54 34.62 47.32 46.40 54 -7.60 4924.00 PK V 36.07 37.77 48.39 50.09 54 -3.91 4924.00 PK H 36.07 37.77 40.56 42.26 54 -11.74 Remark: 1. Correction Factor = Antenna Factor + Cable Loss 2. Corrected Level = Reading + Correction Factor – Preamp. Gain 3. The frequency measured ranges from 1GHz to 25GHz.The data value listed above which is higher than the system noise floor. Page 77 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME EUT : NBG4615 Test Condition : 802.11n HT40 Tx at channel 3 (DAC0+DAC1) Frequency Spectrum Antenna Preamp. Correction Reading Corrected Limit Margin Analyzer Polariz. Gain Factor Level @3m (MHz) Detector (H/V) (dB) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) 3210.00 PK V 35.54 34.62 48.49 47.57 54 -6.43 4844.00 PK V 36.07 37.77 48.12 49.82 54 -4.18 4844.00 PK H 36.07 37.77 39.98 41.68 54 -12.32 Remark: 1. Correction Factor = Antenna Factor + Cable Loss 2. Corrected Level = Reading + Correction Factor – Preamp. Gain 3. The frequency measured ranges from 1GHz to 25GHz.The data value listed above which is higher than the system noise floor. EUT : NBG4615 Test Condition : 802.11n HT40 Tx at channel 6 (DAC0+DAC1) Frequency Spectrum Antenna Preamp. Correction Reading Corrected Limit Margin Analyzer Polariz. Gain Factor Level @3m (MHz) Detector (H/V) (dB) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) 3240.00 PK V 35.54 34.62 45.16 44.24 54 -9.76 4874.00 PK V 36.07 37.77 48.42 50.12 54 -3.88 4874.00 PK H 36.07 37.77 41.31 43.01 54 -10.99 Remark: 1. Correction Factor = Antenna Factor + Cable Loss 2. Corrected Level = Reading + Correction Factor – Preamp. Gain 3. The frequency measured ranges from 1GHz to 25GHz.The data value listed above which is higher than the system noise floor. Page 78 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME EUT : NBG4615 Test Condition : 802.11n HT40 Tx at channel 9 (DAC0+DAC1) Frequency Spectrum Antenna Preamp. Correction Reading Corrected Limit Margin Analyzer Polariz. Gain Factor Level @3m (MHz) Detector (H/V) (dB) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) 3270.00 PK V 35.54 34.62 46.90 45.98 54 -8.02 4904.00 PK V 36.07 37.77 43.87 45.57 54 -8.43 4904.00 PK H 36.07 37.77 38.33 40.03 54 -13.97 Remark: 1. Correction Factor = Antenna Factor + Cable Loss 2. Corrected Level = Reading + Correction Factor – Preamp. Gain 3. The frequency measured ranges from 1GHz to 25GHz.The data value listed above which is higher than the system noise floor. Page 79 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME 8. Emission on Band Edge Name of Test Emission Band Edge Base Standard FCC 15.247(d) Test Result: Complies Measurement Data: See Tables & plots below Method of Measurement: Reference FCC document: KDB558074, ANSI C63.4 The frequency range from 30 MHz to 1000 MHz using Bilog Antenna. The frequency range over 1 GHz using Horn Antenna. Radiated emissions were invested cover the frequency range from 30 MHz to 1000 MHz using a receiver RBW of 120 kHz record QP reading, and the frequency over 1 GHz using a spectrum analyzer RBW of 1 MHz and 10 Hz VBW record Average reading. (15.209 paragraph), the Peak reading (1 MHz RBW/VBW) recorded also on the report. Page 80 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Test Mode: 802.11b (DAC0) The Max. Field Measurement Limit Strength in Margin Channel Freq.Band Detector @3m Restrict (dB) (MHz) (dBuV/m) Band (dBuV/m) PK 61.88 74 -12.12 1 (lowest) 2310-2390 AV 53.28 54 -0.72 PK 62.39 74 -11.61 11 (highest) 2483.5-2500 AV 53.27 54 -0.73 Test Mode: 802.11g (DAC0) The Max. Field Measurement Limit Strength in Margin Channel Freq.Band Detector @3m Restrict (dB) (MHz) (dBuV/m) Band (dBuV/m) PK 63.20 74 -10.80 1 (lowest) 2310-2390 AV 51.82 54 -2.18 PK 70.94 74 -3.06 11 (highest) 2483.5-2500 AV 53.42 54 -0.58 Page 81 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Test Mode: 802.11g (DAC1) The Max. Field Measurement Limit Strength in Margin Channel Freq.Band Detector @3m Restrict (dB) (MHz) (dBuV/m) Band (dBuV/m) PK 63.06 74 -10.94 1 (lowest) 2310-2390 AV 53.20 54 -0.80 PK 63.87 74 -10.13 11 (highest) 2483.5-2500 AV 53.23 54 -0.77 Test Mode: 802.11n HT20 (DAC0+DAC1) The Max. Field Measurement Limit Strength in Margin Channel Freq.Band Detector @3m Restrict (dB) (MHz) (dBuV/m) Band (dBuV/m) PK 63.09 74 -10.91 1 (lowest) 2310-2390 AV 52.32 54 -1.68 PK 64.59 74 -9.41 11 (highest) 2483.5-2500 AV 51.35 54 -2.65 Page 82 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Test Mode: 802.11n HT40 (DAC0+DAC1) The Max. Field Measurement Limit Strength in Margin Channel Freq.Band Detector @3m Restrict (dB) (MHz) (dBuV/m) Band (dBuV/m) PK 63.23 74 -10.77 3 (lowest) 2310-2390 AV 51.91 54 -2.09 PK 65.31 74 -8.69 9 (highest) 2483.5-2500 AV 53.33 54 -0.67 Page 83 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Band edge @ 802.11b mode channel 1 PK (DAC0) Band edge @ 802.11b mode channel 1 AV (DAC0) Page 84 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Band edge @ 802.11b mode channel 11 PK (DAC0) Band edge @ 802.11b mode channel 11 AV (DAC0) Page 85 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Band edge @ 802.11g mode channel 1 PK (DAC0) Band edge @ 802.11g mode channel 1 AV (DAC0) Page 86 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Band edge @ 802.11g mode channel 11 PK (DAC0) Band edge @ 802.11g mode channel 11 AV (DAC0) Page 87 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Band edge @ 802.11g mode channel 1 PK (DAC1) Band edge @ 802.11g mode channel 1 AV (DAC1) Page 88 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Band edge @ 802.11g mode channel 11 PK (DAC1) Band edge @ 802.11g mode channel 11 AV (DAC1) Page 89 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Band edge @802.11n HT20 mode channel 1 PK (DAC0+DAC1) Band edge @802.11n HT20 mode channel 1 AV (DAC0+DAC1) Page 90 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Band edge @802.11n HT20 mode channel 11 PK (DAC0+DAC1) Band edge @802.11n HT20 mode channel 11 AV (DAC0+DAC1) Page 91 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Band edge @802.11n HT40 mode channel 3 PK (DAC0+DAC1) Band edge @802.11n HT40 mode channel 3 AV (DAC0+DAC1) Page 92 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Band edge @802.11n HT40 mode channel 9 PK (DAC0+DAC1) Band edge @802.11n HT40 mode channel 9 AV (DAC0+DAC1) Page 93 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME 9. AC power line conducted emission Name of Test AC power line conducted emission Base Standard FCC 15.207 Test Result: Complies Measurement Data: See Tables & plots below Method of Measurement: Reference FCC document: KDB558074, ANSI C63.4 The EUT are connected to the main power through a line impedance stabilization network (LISN). This provides a 50 ohm/50 uH coupling impedance for the measuring equipment. The peripheral devices are also connected to the main power through a LISN that provides a 50 ohm/ 50 uH coupling impedance with 50 ohm termination. Both sides (Line and Neutral) of AC line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ANSI C63.4/2003 on conducted measurement. The bandwidth of the field strength meter (R & S Test Receiver ESCS 30) is set at 9kHz. The EUT configuration please refer to the “Conducted set-up photo.pdf”. Test Diagram: AC Power (1) LISN 1 EUT Notebook PC LISN 2 EMI Receiver AC Power (1) RJ-45 UTP Cat.5 10 meter Page 94 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Emission Limit: Freq. Conducted Limit (dBuV) (MHz) Q.P. Ave. 0.15~0.50 66 – 56* 56 – 46* 0.50~5.00 56 46 5.00~30.0 60 50 *Decreases with the logarithm of the frequency. Note: The EUT was tested while in continues transmit mode. Page 95 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Phase : Line EUT : NBG4615 Test condition : Continuously mode Remark : Adapter 1 Remark: 1. Correction Factor (dB)= LISN Factor (dB) + Cable Loss (dB) 2. Margin (dB) = Level (dBuV) – Limit (dBuV) Page 96 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Phase : Neutral EUT : NBG4615 Test condition : Continuously mode Remark : Adapter 1 Remark: 1. Correction Factor (dB)= LISN Factor (dB) + Cable Loss (dB) 2. Margin (dB) = Level (dBuV) – Limit (dBuV) Page 97 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Phase : Line EUT : NBG4615 Test condition : Continuously mode Remark : Adapter 2 Remark: 1. Correction Factor (dB)= LISN Factor (dB) + Cable Loss (dB) 2. Margin (dB) = Level (dBuV) – Limit (dBuV) Page 98 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Phase : Neutral EUT : NBG4615 Test condition : Continuously mode Remark : Adapter 2 Remark: 1. Correction Factor (dB)= LISN Factor (dB) + Cable Loss (dB) 2. Margin (dB) = Level (dBuV) – Limit (dBuV) Page 99 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Phase : Line EUT : NBG4615 Test condition : Continuously mode Remark : Adapter 3 Remark: 1. Correction Factor (dB)= LISN Factor (dB) + Cable Loss (dB) 2. Margin (dB) = Level (dBuV) – Limit (dBuV) Page 100 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Phase : Neutral EUT : NBG4615 Test condition : Continuously mode Remark : Adapter 3 Remark: 1. Correction Factor (dB)= LISN Factor (dB) + Cable Loss (dB) 2. Margin (dB) = Level (dBuV) – Limit (dBuV) Page 101 of 102

FCC ID.: I88NBG4615 Report No.: TS10080165-EME Appendix A: Test Equipment List Equipment Brand Frequency range Model No. Last Cal. Cal. interval EMI Test Receiver Rohde & Schwarz 9kHz~2.75GHz ESCS 30 2010/9/3 1 year EMI Test Receiver Rohde & Schwarz 9kHz~3GHz ESCI 2009/12/8 1 year Spectrum Analyzer Rohde & Schwarz 9kHz~30GHz FSP 30 2010/8/16 1 year Spectrum Analyzer Rohde & Schwarz 20Hz~40GHz FSEK 30 2010/1/18 1 year Horn Antenna SCHWARZBECK 1GHz~18GHz BBHA9120D 2010/8/31 2 years Bilog Antenna SCHWARZBECK 25MHz~1.7GHz VULB 9168 2009/9/22 2 years Turn Table HDGmbH N/A DS 420S N/A N/A Antenna Tower HDGmbH N/A MA 240 N/A N/A AFS42-00102 Pre-Amplifier MITER 100MHz~26.5GHz 2009/10/27 2 years 650 LISN Rohde & Schwarz 9KHz~30MHz ESH3-Z5 2009/3/13 2 years 100kHz ~ 65GHz Power Meter Anritsu (video 2495A 2010/10/20 1 year bandwith:65MHz) 300MHz ~ 40GHz Power Senor Anritsu (video 2411B 2010/10/20 1 year bandwith:50MHz) Note: The above equipments are within the valid calibration period. Measurement Uncertainty: Measurement uncertainty was calculated in accordance with TR 100 028-1. Parameter Uncertainty Radiated Emission ±5.056 dB Conducted Emission ±2.786 dB This uncertainty represents an expanded uncertainty expressed at approximately the 95 % confidence level using a coverage factor of k=2. Page 102 of 102


Document Created: 2011-01-19 13:34:55
Document Modified: 2011-01-19 13:34:55
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC