MPE

FCC ID: I88MAX200M1

RF Exposure Info

Download: PDF
FCCID_903008

FCC ID. : I88MAX200M1 Report No.: EME-071149 Page 1 of 9 Maximum Permissible Exposure (MPE) Evaluation Report Report No. : EME-071149 Model No. : MAX-200M1 Issued Date : Nov. 06, 2007 Applicant : ZyXEL Communications Corporation 6, Innovation Rd II, Science-Based Industrial Park, Hsin-Chu, Taiwan Test By : Intertek Testing Services Taiwan Ltd. No. 11, Lane 275, Ko-Nan 1 Street, Chia-Tung Li, Shiang-Shan District, Hsinchu City, Taiwan This test report consists of 9 pages in total. It may be duplicated completely for legal use with the allowance of the applicant. It shall not be reproduced except in full, without the written approval of Intertek Laboratory. The test result(s) in this report only applies to the tested sample(s). Project Engineer Reviewed By Jimmie Liu Kevin Chen

FCC ID. : I88MAX200M1 Report No.: EME-071149 Page 2 of 9 Table of Contents Summary of Tests ............................................................................................................. 3 1. Introduction .................................................................................................................. 4 2. RF Exposure Limit ....................................................................................................... 4 3. RF Exposure calculations ............................................................................................. 5 4. Test results .................................................................................................................... 5

FCC ID. : I88MAX200M1 Report No.: EME-071149 Page 3 of 9 Summary of Tests MPE Evaluation meet FCC OET No. 65: 1997/ IEEE C95.1-1999 WiMAX IEEE802.16e Indoor Basic CPE-2.5GHz -Model: MAX-200M1 FCC ID: I88MAX200M1 Test Reference Results MPE Evaluation FCC Guidelines for Human Exposure IEEE C95.1 Pass

FCC ID. : I88MAX200M1 Report No.: EME-071149 Page 4 of 9 1. Introduction The EUT operates in the 2.5GHz band about WiMAX IEEE 802.16e. Due to the EUT (include antenna) at its normal operation distance is at least 20 cm from the human body, the EUT was defined as a Mobile Device. The reason to do the MPE Evaluation is to avoid the RF hazard to human body. The maximum output power and gain of the antenna were used to calculate the limited Power density (S) at 20cm distance away from the product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. According to 1.1307 (b)(1), systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. 2. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b). Limits for Maximum Permissible Exposure (MPE) Frequency Electric Field Magnetic Field Power Density Average Time Range Strength Strength (mW/cm2) (minutes) (MHz) (V/m) (A/m) (A) Limits for Occupational / Control Exposures 30-300 61.4 0.163 1.0 6 300-1500 - - F/300 6 1500-100,000 - - 5 6 (B) Limits for General Population / Uncontrolled Exposure 30-300 27.5 0.073 0.2 30 300-1500 - - F/1500 30 1500-100,000 - - 1.0 30 F= Frequency in MHz

FCC ID. : I88MAX200M1 Report No.: EME-071149 Page 5 of 9 3. RF Exposure calculations From §FCC 1.1310 table 1, the maximum permissible RF exposure for an uncontrolled environment is 1mW/(cm2) Power density (S) is calculated by the following formula: S = (P * G)/4πR2 where, S = Power density (mW/cm2) P = Output power to antenna (mW) R = Distance between radiating structure and observation point (cm) G = Gain of antenna in numeric π = 3.1416 Example: Assume a mobile device operates at 2412MHz and its maximum output power is 50mW, and the maximum gain of antenna is 1 (numeric) /0dBi. then the power density (S) = (50 * 1)/4*π*202 = 0.00995 (mW/cm2) 4. Test results Environmental Input Power Antenna Type Modulation Coding Rate Conditions 120Vac, 60Hz 26℃, 65% Dipole antenna QPSK 1/2 Maximum Output Power Limit of Frequency antenna power density power Band Width (MHz) gain to antenna density (MHz) (numeric (mW) (mW/cm2) (mW/cm2) 2500 1.41 116.1449 0.03264 1.0 5 2590 1.41 119.6741 0.03363 1.0 5 2685 1.41 77.2681 0.02171 1.0 5 2500 1.41 115.6112 0.03249 1.0 10 2590 1.41 113.2400 0.03182 1.0 10 2685 1.41 74.1310 0.02083 1.0 10 The Notice in Installation Manual has been stated as below: While installing and operating this transmitter, the radio frequency exposure limit of 1mW/(cm*cm) may be exceeded at distances close to the transmitter. therefore, the user must maintain a minimum distance of 20 cm from the device at all time.

FCC ID. : I88MAX200M1 Report No.: EME-071149 Page 6 of 9 Environmental Input Power Antenna Type Modulation Coding Rate Conditions 120Vac, 60Hz 26℃, 65% Dipole antenna QPSK 3/4 Maximum Output Power Limit of Frequency antenna power density power Band Width (MHz) gain to antenna density (MHz) (numeric (mW) (mW/cm2) (mW/cm2) 2500 1.41 111.6863 0.03139 1.0 5 2590 1.41 116.1449 0.03264 1.0 5 2685 1.41 75.3356 0.02117 1.0 5 2500 1.41 112.4605 0.03160 1.0 10 2590 1.41 109.9006 0.03088 1.0 10 2685 1.41 72.7780 0.02045 1.0 10 Environmental Input Power Antenna Type Modulation Coding Rate Conditions 120Vac, 60Hz 26℃, 65% Dipole antenna 16QAM 1/2 Maximum Output Power Limit of Frequency antenna power density power Band Width (MHz) gain to antenna density (MHz) (numeric (mW) (mW/cm2) (mW/cm2) 2500 1.41 109.3956 0.03074 1.0 5 2590 1.41 112.4605 0.03160 1.0 5 2685 1.41 73.6207 0.02069 1.0 5 2500 1.41 110.6624 0.03110 1.0 10 2590 1.41 107.8947 0.03032 1.0 10 2685 1.41 71.2853 0.02003 1.0 10 The Notice in Installation Manual has been stated as below: While installing and operating this transmitter, the radio frequency exposure limit of 1mW/(cm*cm) may be exceeded at distances close to the transmitter. therefore, the user must maintain a minimum distance of 20 cm from the device at all time.

FCC ID. : I88MAX200M1 Report No.: EME-071149 Page 7 of 9 Environmental Input Power Antenna Type Modulation Coding Rate Conditions 120Vac, 60Hz 26℃, 65% Dipole antenna 16QAM 3/4 Maximum Output Power Limit of Frequency antenna power density power Band Width (MHz) gain to antenna density (MHz) (numeric (mW) (mW/cm2) (mW/cm2) 2500 1.41 107.8947 0.03032 1.0 5 2590 1.41 111.6863 0.03139 1.0 5 2685 1.41 72.2770 0.02031 1.0 5 2500 1.41 108.1434 0.03039 1.0 10 2590 1.41 105.9254 0.02977 1.0 10 2685 1.41 69.3426 0.01947 1.0 10 Environmental Input Power Antenna Type Modulation Coding Rate Conditions 120Vac, 60Hz 26℃, 65% Patch antenna QPSK 1/2 Maximum Output Power Limit of Frequency antenna power density power Band Width (MHz) gain to antenna density (MHz) (numeric (mW) (mW/cm2) (mW/cm2) 2500 1.41 116.1449 0.03264 1.0 5 2590 1.41 119.6741 0.03363 1.0 5 2685 1.41 77.2681 0.02171 1.0 5 2500 1.41 115.6112 0.03249 1.0 10 2590 1.41 113.2400 0.03182 1.0 10 2685 1.41 74.1310 0.02083 1.0 10 The Notice in Installation Manual has been stated as below: While installing and operating this transmitter, the radio frequency exposure limit of 1mW/(cm*cm) may be exceeded at distances close to the transmitter. therefore, the user must maintain a minimum distance of 20 cm from the device at all time.

FCC ID. : I88MAX200M1 Report No.: EME-071149 Page 8 of 9 Environmental Input Power Antenna Type Modulation Coding Rate Conditions 120Vac, 60Hz 26℃, 65% Patch antenna QPSK 3/4 Maximum Output Power Limit of Frequency antenna power density power Band Width (MHz) gain to antenna density (MHz) (numeric (mW) (mW/cm2) (mW/cm2) 2500 1.41 111.6863 0.03139 1.0 5 2590 1.41 116.1449 0.03264 1.0 5 2685 1.41 75.3356 0.02117 1.0 5 2500 1.41 112.4605 0.03160 1.0 10 2590 1.41 109.9006 0.03088 1.0 10 2685 1.41 72.7780 0.02045 1.0 10 Environmental Input Power Antenna Type Modulation Coding Rate Conditions 120Vac, 60Hz 26℃, 65% Patch antenna 16QAM 1/2 Maximum Output Power Limit of Frequency antenna power density power Band Width (MHz) gain to antenna density (MHz) (numeric (mW) (mW/cm2) (mW/cm2) 2500 1.41 109.3956 0.03074 1.0 5 2590 1.41 112.4605 0.03160 1.0 5 2685 1.41 73.6207 0.02069 1.0 5 2500 1.41 110.6624 0.03110 1.0 10 2590 1.41 107.8947 0.03032 1.0 10 2685 1.41 71.2853 0.02003 1.0 10 The Notice in Installation Manual has been stated as below: While installing and operating this transmitter, the radio frequency exposure limit of 1mW/(cm*cm) may be exceeded at distances close to the transmitter. therefore, the user must maintain a minimum distance of 20 cm from the device at all time.

FCC ID. : I88MAX200M1 Report No.: EME-071149 Page 9 of 9 Environmental Input Power Antenna Type Modulation Coding Rate Conditions 120Vac, 60Hz 26℃, 65% Patch antenna 16QAM 3/4 Maximum Output Power Limit of Frequency antenna power density power Band Width (MHz) gain to antenna density (MHz) (numeric (mW) (mW/cm2) (mW/cm2) 2500 1.41 107.8947 0.03032 1.0 5 2590 1.41 111.6863 0.03139 1.0 5 2685 1.41 72.2770 0.02031 1.0 5 2500 1.41 108.1434 0.03039 1.0 10 2590 1.41 105.9254 0.02977 1.0 10 2685 1.41 69.3426 0.01949 1.0 10 The Notice in Installation Manual has been stated as below: While installing and operating this transmitter, the radio frequency exposure limit of 1mW/(cm*cm) may be exceeded at distances close to the transmitter. therefore, the user must maintain a minimum distance of 20 cm from the device at all time.


Document Created: 2007-11-28 16:57:33
Document Modified: 2007-11-28 16:57:33
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC